Whirlpool MGD7100DC0 Guide d'installation

Marque: Whirlpool

Modèle: MGD7100DC0

Catégorie: Sèche-linge

Taper: Guide d'installation

GAS DRYER INSTALLATION INSTRUCTIONS

CANADIAN ELECTRIC DRYER INSTRUCTIONS

INSTRUCTIONS POUR L'INSTALLATION DE LA St_CHEUSE

GAZ (I_.-U. ET CANADA)

I_LECTRIQUE (CANADA UNIQUEMENT)

Table of Contents

DRYER SAFETY .......................................................................... 2

iNSTALLATiON REQUIREMENTS .............................................. 4

Tools and Parts ...................................................................... 4

LOCATION REQUIREMENTS ..................................................... 5

ELECTRIC DRYER POWER HOOKUP-CANADA ONLY ........... 6

GAS DRYER POWER HOOKUP ................................................. 7

iNSTALL LEVELING LEGS .......................................................... 9

MAKE GAS CONNECTION ......................................................... 9

VENTING .................................................................................... 10

Venting Requirements ......................................................... 10

Plan Vent System ................................................................. 11

Install Vent System .............................................................. 12

CONNECT iNLET HOSE (STEAM MODEL ONLY) ................... 12

CONNECT VENT ....................................................................... 14

LEVEL DRYER ........................................................................... 14

COMPLETE iNSTALLATiON CHECKLIST ............................... 15

DOOR REVERSAL (OPTIONAL) ............................................... 15

Table des mati_res

SECURITE DE LA SECHEUSE .................................................. 23

EXIGENCES D'INSTALLATION ................................................. 25

Outillage et pi_ces ............................................................. 25

EXIGENCES D'EMPLACEMENT ............................................... 26

SLeCHEUSE ELECTRIQUE RACCORDEMENT A

UALIMENTATION leLECTRIQUE - CANADA SEULEMENT ..... 27

RACCORDEMENT D'UNE SLeCHEUSE A GAZ ........................ 28

iNSTALLATiON DES PIEDS DE NIVELLEMENT ...................... 30

RACCORDEMENT AU GAZ ....................................................... 30

EVACUATION ............................................................................. 31

Exigences concernant 1'6vacuation ................................. 31

Planification du syst_me d'_vacuation ............................ 32

installation du syst_me d'_vacuation ............................... 34

RACCORDEMENT DU TUYAU D'ALIMENTATION

(MOD_=LE A VAPEUR UNIQUEMENT) ...................................... 34

RACCORDEMENT DU CONDUIT DqeVACUATION ................. 36

REGLAGE DE L'APLOMB DE LA SLeCHEUSE .......................... 36

ACHEVER [.'iNSTALLATiON LISTE DE VERIFICATION ........... 37

INVERSION DE LA PORTE (FACULTATIF) ................................ 37

Para una version de estas instrucciones en espa_ol, visite www.Whirlpool.com

iNSTALLATiON NOTES

Date of purchase:

Date of installation:

installer:

Model number:

Serial number:

NOTES CONCERNANT L'INSTALLATION

Date d'achat:

Date d'installation:

Installateur:

Num_ro de module:

Num_ro de s_rie:

W10573707B

W10573708B=SP

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING - ...i.. ofFi,o..

- Clothes dryer installation must be performed by a qualified installer,

- install the clothes dryer according to the manufacturer's instructions and local codes.

- Do not install a clothes dryer with flexible plastic venting materials or flexible metal

(foil type) duct. if fie×ible metal duct is installed, it must be of a specific type identified

by the appliance manufacturer as suitable for use with clothes dryers. Fle×ible venting

materials are known to collapse, be easily crushed, and trap lint. These conditions will

obstruct clothes dryer airflow and increase the risk of fire.

= To reduce the risk of severe injury or death, follow all installation instructions,

= Save these instructions,

WARNING: For your safety, the information in this manual must be followed to minimize I

the risk of fire or explosion, or to prevent property damage, personal injury, or death, j

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO iF YOU SMELL GAS:

®Do not try to light any appliance.

®Do not touch any electrical switch; do not use any phone in your building.

®Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

o if you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

WARNING: Gas leaks cannot always be detected by smell.

Gas suppliers recommend that you use a gas detector approved by UL or CSA.

For more information, contact your gas supplier.

If a gas leak is detected, follow the "What to do if you smell gas" instructions.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSi Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

In the State of Massachusetts, the following installation instructions apply:

[] installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] if using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

iMPORTANT: When discarding or storing your old clothes dryer, remove the door.

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed for all installations:

Flat-blade screwdriver

#2 Phillips screwdriver

1/4" and 5/16" nut driver Level

recommended)

Tape measure Pliers

Utility knife Tin snips (new vent installations)

Caulking gun and compound Adjustable wrench that opens to

(new vent installations) 1" (25 mm) or hex-head socket wrench

Tools needed for gas installations:

Parts supplied (all models):

Leveling legs (4)

Parts supplied (steam models):

"Y" connector

Parts package is located in dryer drum. Check that all parts

are included.

NOTE: Do not use leveling legs supplied with dryer if installing

with a pedestal or a stack kit.

Parts needed: (Not supplied with dryer)

[] Vent clamps

[] Vent elbows and vent work

Parts needed (steam models):

2' (0.6 m) inlet hose

5' (1.52 m) inlet hose

and rubber washer

Additional parts may be required, depending in your installation.

Check local codes. Check existing electrical supply and venting.

Read "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

Optional Equipment: (Not supplied with dryer)

Refer to your Use and Care Guide for information about

accessories available for your dryer.

8" or 10" pipe wrench

Pipe-joint compound

resistant to LP gas

8" or 10" adjustable wrench

(for gas connections)

LOCATIONREQUIREMENTS

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at Jeast 18 inches (460 rnm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

DRYER DiMENSiONS

Front view:

383/4ii Min.

(984 ram)

39" Max,

(990 ram)

4-- 27" --_

(686 ram)

[

, ©

You will need:

[] A location allowing for proper exhaust installation.

See "Venting Requirements."

[] A separate 15 or 20 amp circuit for a gas dryer or 30 amp

circuit for an electric dryer.

[] If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer.

See "Electrical Requirements."

[] Floor must support dryer weight of 200 Ibs. (90.7 kg).

Also consider weight of companion appliance.

[] Cold water faucets located within 4 ft. (1.2 m) of the water

fill valves, and water pressure of 20 - 120 psi (138 - 827 kPa).

You may use the water supply for your washer using the

supplied "Y" connector and a short hose (which you will

need to purchase).

[] Level floor with maximum slope of 1" (25 mm) under entire

dryer. If slope is greater than 1" (25 mm), install Extended

Dryer Feet Kit, Part Number 279810. If not level, clothes

may not tumble properly and automatic sensor cycles may

not operate correctly.

[] For garage installation, place dryer at least 18" (460 mm)

above floor. If using a pedestal, you will need 18" (460 mm)

to bottom of dryer.

[] The dryer must not be installed or stored in an area where

it will be exposed to water and/or weather.

iMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below

40° F (4° C). Lower temperatures may cause dryer not to

shut off at end of automatic sensor cycles, resulting in longer

drying times.

Side view:

(1220 ram).

31"

(787mm)

3/4_1"

(18 rnm)

53/4 li*

(146 turn)

J 31/2"

(257 ram)

* Approx. measurement

Back view:

Waterinlet

(Steam Models Onl

Vent m_J

--d

61/4"

(159 rnm)

297/8"*

(759 ram)

(156 ram)

Approx. measurement

NOTE: Most installations require a minimum of 5" (127 mm)

clearance behind dryer for exhaust vent with elbow. See "Venting

Requirements."

Installation Clearances

For each arrangement, consider allowing more space for ease

of installation and servicing; spacing for companion appliances

and clearances for walls, doors, and floor moldings. Space

must be large enough to allow door to fully open. Add spacing

on all sides of dryer to reduce noise transfer. If a closet door

or Iouvered door is installed, top and bottom air openings

in door are required.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

NOTE: No other fuel-burning appliance can be installed in the

same closet as a dryer.

installation spacing for recessed area

or closet installation

All dimensions show recommended and minimum spacing

allowed.

[] Additional spacing should be considered for ease of

installation and servicing.

[] Additional clearances might be required for wall, door, floor

moldings, dryer venting, and gas line.

[] Additional spacing should be considered on all sides

of the dryer to reduce noise transfer.

[] For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

[] Companion appliance spacing should also be considered.

Recommended installation clearances {dryer only):

Mobile home installations require:

[] Metal exhaust system hardware, available for purchase from

your dealer. For further information, see "Assistance or

Service" section in your Use and Care Guide.

[] Special provisions must be made in mobile homes to

introduce outside air into dryer. Openings (such as a nearby

window) should be at least twice as large as dryer exhaust

opening.

For mobile home installation of gas dryers:

[] Mobile Home Installation Hold-down Kit Part Number 346764

is available to order. For further information, see "Assistance

or Service" section in your Use and Care Guide.

ELECTRIC DRYER

POWER HOOKUP - CANADA ONLY

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 4 prong outlet,

Failure to do so can result in death or electrical shock.

', "':-=2

5 H * i i,

(127 ram) "

(76 ram)

* 0" (0 mm) spacing is allowed.

Mobile home = Additional installation requirements:

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR,

Part 3280 (formerly the Federal Standard for Mobile home

construction and Safety, Title 24, HUD Part 280) or Standard

CAN/CSA-Z240 MH.

It is your responsibility:

[] To contact a qualified electrical installer.

[] To be sure that the electrical connection is adequate and in

conformance with Canadian Electrical Code, C22.1 - latest

edition and all local codes. A copy of above codes standard

may be obtained from: Canadian Standards Association,

178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

[] To supply the required 4 wire, single phase, 120/240 volt,

60 Hz, AC only electrical supply on a separate 30-amp circuit,

fused on both sides of the line. A time-delay fuse or circuit

breaker is recommended. Connect to an individual branch

circuit.

[]

This dryer is equipped with a CSA

International Certified Power Cord

intended to be plugged into a standard

14-30R wall receptacle. The cord is 5 ft.

(1.52 m) long. Be sure wall receptacle is

within reach of dryer's final location.

4-wire receptacle

(14-30R)

If using a replacement power supply cord, it is recommended that

you use Power Supply Cord Replacement Part Number 8529008.

For further information, please reference service numbers located

in "Assistance or Service" section of your Use and Care Guide.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS DRYER POWER HOOKUP

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

FaiJure to follow these instructions can result in death,

fire, or electrical shock.

[] 120 Volt, 60 Hz, AC only, 15- or 20- amp fused electrical

supply is required. A time-delay fuse or circuit breaker is

recommended. It is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNinG: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with

the dryer: if it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

GAS SUPPLY REQUIREMENTS

Explosion Hazard

Use a new CSA international approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (330 ram) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

GAS TYPE

Natural Gas:

This dryer is equipped for use with Natural gas. It is design-

certified by CSA international for LP (propane or butane) gases

with appropriate conversion.

[] Your dryer must have the correct burner for the type of gas in

your home. Burner information is located on the rating plate in

the door well of your dryer. If this information does not agree

with the type of gas available, contact your dealer or call the

phone numbers referenced in the "Assistance or Service"

section of your Use and Care Guide.

LP Gas Conversion:

iMPORTANT: Conversion must be made by a qualified

technician.

No attempt shall be made to convert the appliance from the gas

specified on the model/serial rating plate for use with a different

gas without consulting your gas company.

GASSUPPLYLiNE

Option 1 (Recommended Method)

Flexible stainless steel gas connector:

[] If local codes permit, use a new flexible stainless steel gas

connector (Design Certified by the American Gas Association

or CSA International) to connect your dryer to the rigid gas

supply line. Use an elbow and a 3/8" flare x 3/8" NPT adapter

fitting between the stainless steel gas connector and the dryer

gas pipe, as needed to prevent kinking.

Option 2 (Alternate Method)

Approved aluminum or copper tubing:

[] Must include 1/8" NPT minimum plugged tapping accessible

for test gauge connection, immediately upstream of the gas

connection to the dryer. See illustration.

[] 1/2" IPS pipe is recommended.

[] 3/8" approved aluminum or copper tubing is acceptable for

lengths under 20 ft. (6.1 m) if local codes and gas supplier

permit.

[] If you are using Natural gas, do not use copper tubing.

[] Lengths over 20 ft. (6.1 m) should use larger tubing and

a different size adapter fitting.

[] If your dryer has been converted to use LP gas, 3/8" LP

compatible copper tubing can be used. If the total length of the

supply line is more than 20 ft. (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of LP gas

must be used. Do not use TEFLON_'*_ttape.

[] Must include shut-off valve

GAS SUPPLY CONNECTION REQUIREMENTS

[] Use an elbow and a 3/8" flare x 3/8" NPT adapter fitting

between the flexible gas connector and the dryer gas pipe,

as needed to avoid kinking.

[] Use only pipe-joint compound. Do not use TEFLON <etape.

[] This dryer must be connected to the gas supply line with a

listed flexible gas connector that complies with the standard for

connectors for gas appliances, ANSi Z21.24 or CSA 6.10.

BURNER INPUT REQUIREMENTS

Elevations above 2,000 ft. (610 m):

[] When installed above 2,000 ft. (610 m) a 4% reduction of the

burner Btu rating shown on the model/serial number plate is

required for each 1,000 ft. (305 m) increase in elevation.

Gas supply pressure testing

[] The dryer must be disconnected from the gas supply piping

system during pressure testing at pressures greater than

1/2 psi.

DRYER GAS PiPE

[] The gas pipe that comes out through the rear of your dryer has

a 3/8" male pipe thread.

in the U.S.A.:

An individual manual shut-off valve must be installed within

six (6) ft. (1.8 m) of the dryer in accordance with the National

Fuel Gas Code, ANSi Z223.1. The location should be easy to

reach for opening and closing.

In Canada:

An individual manual shut-off valve must be installed in

accordance with the B149.1, Natural Gas and Propane

installation Code. It is recommended that an individual

manual shut-off valve be installed within six (6) ft. (1.8 m) of

the dryer. The location should be easy to reach for opening

and closing.

A !_

A. 3/8" flexible gas connector

B. 3/8" pipe to flare adapter fitting

C. 1/8" NPT minimum plugged tapping

D. 1/2" NPT gas supply line

E. Gas shut-off valve.

*5¾"

(146 ram}

1/2nn

(38 ram)

3/8" NPT dryer gas pipe

* NOTE: If the dryer is mounted on a pedestal, the gas

pipe height must be an additional 10" (254 mm) or

15.5" (394 mm) from the floor, depending on the pedestal

model. For a garage installation, the gas pipe height must

be an additional 18" (460 mm) from the floor.

t®TEFLON is a registered trademark of E.I. Dupont De Nemours and Company.

INSTALL LEVELING LEGS

Excessive Weight Hazard

Use two or more people to move and install dryer,

Failure to do so can result in back or other injury.

F1, Prepare dryer for leveling legs

m m

To avoid damaging floor, use a large flat piece of cardboard

from dryer carton; place under entire back edge of dryer.

Firmly grasp dryer body (not console panel) and gently lay

dryer down on cardboard.

2, Screw in leveling legs _"_

diamond

marking

(

Examine leveling legs, find diamond marking. Screw legs into

leg holes by hand - use a wrench to finish turning legs until

diamond marking is no longer visible.

Place a carton corner post from dryer packaging under each

of the 2 dryer back corners. Stand the dryer up. Slide the

dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

MAKE GAS CONNECTION

(gas models only)

1, Connect gas supply to dryer

A • • • r_

• • B

A. Flared male fitting

B. Non-flared male fitting

Remove red cap from gas pipe. Using a wrench to tighten,

connect gas supply to dryer. Use pipe-joint compound

on threads of all non-flared male fittings. Ifflexible metal

tubing is used, be sure there are no kinks.

NOTE: For LP gas connections, you must use pipe-joint

compound resistant to action of LP gas Do not use

TEFLON ®tape.

2, Plan pipe fitting connection (option

/•

A B

A. 3/8" flexible gas connector C. 3/8" to 3/8" pipe elbow

B.3/8" dryer gas pipe D. 3/8" pipe-to-flare adapter

fitting

A combination of pipe fittings must be used to connect dryer

to existing gas line. A recommended connection is shown.

Your connection may be different, according to supply line

type, size, and location.

f3, Open shut-off valve

A. Closedvalve

B. Openvalve

Open shut-off valve in supply line; valve is open when handle

is parallel to gas pipe. Then, test all connections by brushing

on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leak found.

VENTING

Venting Requirements

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed space

of a building. Only rigid or flexible metal vent shall be used for

exhausting.

[]

( 0'

(102 rnrn)

4" (102 ram) heavy metal exhaust vent

Only a 4" (102 mm) heavy metal exhaust vent and clamps

may be used.

Do not use plastic or metal foil vent.

Rigid metal vent:

[] Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only ifaccessible to clean)

[] Must be fully extended and supported in final dryer location.

[] Remove excess to avoid sagging and kinking that may result

in reduced airflow and poor performance.

[] Do not install in enclosed walls, ceilings, or floors.

[] The total length should not exceed 73/4ft. (2.4 m).

[] The length of flexible metal vent used must be included in

the overall vent system design as shown in the "Vent System

Charts."

NOTE: If using an existing vent system, clean lint from entire

length of the system and make sure exhaust hood is not plugged

with lint. Replace plastic or metal foil vents with rigid metal

or flexible metal vents. Review "Vent System Charts" and if

necessary, modify existing vent system to achieve best drying

performance.

Exhaust hoods:

[] An exhaust hood should cap the vent to keep rodents and

insects from entering the home.

[] Must be at least 12" (305 mm) from ground or any object

that may obstruct exhaust (such as flowers, rocks, bushes,

or snow).

[] Do not use an exhaust hood with a magnetic latch.

Recommended Styles:

Louvered Hood

Acceptable Style:

Angled Hood

Elbows:

Box Hood

[] 45° elbows provide better airflow than 90° elbows.

Bet

Clamps:

[] Use clamps to seal all joints.

[] Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct

and catch lint. Do not use duct ta )e.

Improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Plan Vent System

Choose your exhaust installation type

Recommended exhaust installation:

A. Dryer R Rigid metal or

B Elbow flexible metal vent

C. Wall G. Vent length

D. Exhaust hood necessary to

E. Clamps connect elbows

H. Exhaust outlet

Fire Hazard

Cover unused exhaust holes with a manufacturer's

exhaust cover kit.

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

Optional exhaust installations:

This dryer can be converted to exhaust out the right side, left

side (all models except WGD71HEW), or through the bottom. If

you prefer, you may contact your local dealer to have the dryer

converted.

A B C

A. Standard rear offset exhaust installation

B. Left- or right-side exhaust installation

C. Bottom exhaust installation

Special provisions for mobile homes:

Exhaust vent must be securely fastened to a noncombustible

portion of mobile home and must not terminate beneath the

mobile home. Terminate exhaust vent outside.

t-4 _-

Determine vent path:

[] Select route that will provide straightest and most direct

path outdoors.

[] Plan installation to use fewest number of elbows and turns.

[] When using elbows or making turns, allow as much room

as possible.

[] Bend vent gradually to avoid kinking.

[] Use as few 90° turns as possible.

Determine vent length and elbows needed for best

drying performance:

[] Use the "Vent System Charts" on the next page to determine

type of vent material and hood combinations acceptable to

use.

NOTE: Do not use vent runs longer than those specified

in "Vent System Charts."

Exhaust systems longer than those specified will:

[] Shorten life of dryer.

[] Reduce performance, resulting in longer drying times

and increased energy usage.

The "Vent System Charts" provide venting requirements

that will help achieve best drying performance.

Standard Vent System Chart

Number of Type Angled

90° elbows of vent hoods

0 Rigid metal 64 ft. (20 m)

1 Rigid metal 54 ft. (16.5 m)

Rigid metal 44 ft. (13.4 m)

Rigid metal 35 ft. (10.7 m)

Rigid metal 27 ft. (8.2 m)

Long Vent System Chart*

Number of Type Angled

90° elbows of vent hoods

0 Rigid metal 160 ft. (48.8 m)

1 Rigid metal 150 ft. (45.7 m)

2 Rigid metal 140 ft. (42.7 m)

3 Rigid metal 130 ft. (39.6 m)

4 Rigid metal 120 ft. (36.6 m)

*For Model WGD71 HEW only; for all other models, refer to the

Standard Vent System Chart above. To find your model number,

refer to the model and serial number plate in the inner door well.

NOTE: For long vent systems, use of box/Iouvered hoods will

improve venting regardless of length.

Install Vent System

1, Install exhaust hood

_ 12" rain.

Install exhaust hood and use caulking compound to seal

exterior wall opening around exhaust hood.

2. Connect vent to exhaust hood

Vent must fit over the exhaust hood. Secure vent to exhaust

hood with 4" (102 mm) clamp. Run vent to dryer location using

straightest path possible. Avoid 90° turns. Use clamps to seal

all joints. Do not use duct tape, screws, or other fastening

devices that extend into interior of vent to secure vent,

because they can catch lint.

CONNECT INLET HOSE

(STEAM MODEL ONLY)

For non-steam models, skip to "Connect Vent."

The dryer must be connected to the cold water faucet using the

new inlet hoses (not supplied). Do not use old hoses.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates on

the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

Turn cold water off, remove hose,

and replace rubber washer

Turn cold water faucet off and remove washer inlet hose.

Remove old rubber washer from inlet hose and replace with

new rubber washer.

Attach2ft(0.6m)inlethosetocoldwaterfaucet.Screwon

couplingbyhanduntilitisseatedonfaucet.Thenattach"Y"

connectortomaleendofthe2ft(0.6m)inlethose.Screwon

couplingbyhanduntilitisseatedonconnector.

Attach long hose to dryer fill valve

and tighten coupling

Remove protective cap from

water inlet valve. Attach other end

of long hose to fill valve at bottom of dryer

back panel. Screw on coupling by hand until it is seated on

fill valve connector. Using pliers, tighten the couplings an

additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling

can result.

Using pliers, tighten the couplings with additional two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

connector and tighten couplings

Check that the water faucets are turned on.

Attach one of the 5 ft (1.5 m) inlet hose ends to the "Y"

connector. Attach washer cold inlet hose to other side of

"Y" connector. Screw on coupling by hand until it is seated

on connector. Using pliers, tighten the couplings an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the coupling can result.

Check for leaks around "Y" connector, faucet, and hoses.

CONNECT VENT

1, Connect vent to exhaust outlet

Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure vent is

clean. Dryer vent must fit over dryer exhaust outlet and inside

exhaust hood. Check that vent is secured to exhaust hood

with a 4" (102 mm) clamp.

2, Move dryer to final location

Move dryer to final location, taking care not to crush or

kink vent or flexible gas line.

After dryer is in place, remove corner posts and cardboard

from under dryer.

LEVEL DRYER

fl -. Level dryer

Place

level here

Check levelness of dryer from

side to side. Repeat from front to back.

NOTE: The dryer must be level for the moisture sensing system

to operate correctly

Not Level LEVEL Not Level

Adjust leveling legs

If dryer is not level, prop up using a wood block, use wrench

to adjust legs up or down, and check again for levelness.

Once dryer is level, make sure all four legs are snug against

the floor and the dryer does not rock.

COMPLETE INSTALLATION

CHECKLIST

[_ Check that all parts are now installed. Ifthere is an extra

part, go back through steps to see what was skipped.

[_ Check that you have all of your tools.

[_ Dispose of/recycle all packaging materials.

[_ Be sure the water faucets are on.

[_ Check for leaks around "Y" connector, faucet, and hoses.

[_ Check dryer's final location. Be sure vent is not crushed

or kinked.

[_ Check that dryer is level. See "Level Dryer."

[_ Remove film on console and any tape remaining on dryer.

[_ Wipe dryer drum interior thoroughly with a damp cloth to

remove any dust.

[_ Read "Dryer Use" in your Use and Care Guide.

[_ If you live in a hard water area, use of a water softener is

recommended to control the buildup of scale through the

water system in the dryer. Over time, the buildup of lime

scale may clog different parts of the water system, which will

reduce product performance. Excessive scale buildup may

lead to the need for certain part replacement or repair.

Electric Models

[_ Plug into a grounded outlet.

Gas Models

[_ Plug into a grounded outlet.

[_ Check that gas supply is on.

[_ Check for leaks.

[_ Check to be sure that the flexible gas line is not crushed

or kinked.

All Models:

[_ Select aTimed Dry heated cycle, and start dryer. Do not

select Air Only Temperature setting.

if dryer will not start, check the following:

• Start button has been pressed firmly.

• Dryer is plugged into an outlet and/or electrical supply is

connected.

• Household fuse is intact and tight, or circuit breaker has

not tripped.

• Dryer door is closed.

This dryer automatically runs an installation diagnostic routine

at the start of its first cycle.

NOTE: You may notice an odor when dryer is first heated. This

odor is common when heating element is first used. The odor will

go away.

DOOR REVERSAL (OPTIONAL)

The following instructions are for models with a round and

square-shaped doors.

Tools needed:

Min. 8" long TORX®tt

T25®** screwdriver

#2 Phillips screwdriver

Reverse door swing round-shaped door - single handle

IMPORTANT: If the protective film has not yet been

removed from the dryer, peel the film from the dryer

door before proceeding.

Using a TORX ®T25®screwdriver, remove the 4 screws

securing the door hinge to the dryer and lift up and out to

remove the door. Place the door on a soft towel or other

non-scratch surface. Reinstall the 4 screws in the holes.

*t ® TORX and T25 are registered trademarks of Acument Intellectual Properties, LLC.

® ®

@ ®

Using a TORX ®T25®screwdriver, remove the 2 screws

securing the door strike to the door frame of the dryer. Rotate

the strike 180° and attach to the opposite side of dryer door

frame, as shown.

_, Remove inner door from outer door

_sr

Position the door with the inside of the door facing up.

Using a Phillips screwdriver, remove the 10 screws securing

the inner door to the outer door. Lift off the inner door and

set aside.

4, Remove outer window assembly

from trim ring

Fig. A

Fig. B

Using a Phillips screwdriver, remove the 2 screws from the

outer window retainer and rotate the outer window assembly

clockwise until the square notches line up with the 4 tabs

on the trim ring indicated with arrows in the figure A above.

Then lift out the outer window and retainer up and off the trim

ring and set aside (B).

5, Reverse outer window assembly

Handle

Fig. A

Handle

Fig. B

Using a Phillips screwdriver, remove the 4 screws from the

outer window retainer and lift off the trim ring off the window

(A). Rotate trim ring 180° and secure with the 4 screws

removed earlier (B).

--_

6, Rotate and reassemble outer window

assembly to trim ring

Bottom

of door

Notches

Fig. A

Fig. B

With the edge with 2 notches at the top, align the notches

on the outer window assembly with the tabs on the trim ring

and lower into place as shown in figure A. Rotate the outer

window assembly counterclockwise to lock tabs into place

(figure B). Using a Phillips screwdriver, secure with 2 screws

removed earlier.

IMPORTANT: Do not overtighten.

Remove hinge and latch

Hinge

Using a TORX®T25®screwdriver, remove the 3 TORX®screws

securing the latch plate and latch backing plate and the

5 screws holding the hinge assembly in place.

9. Reinstall inner door assembly

: 9 Bottom

of door

Position the door with the inside of the door facing up.

Reinstall the 10 screws securing the inner door to the

outer door.

8. Reinstall hinge and latch on

opposite sides

Using a TORX ®T25®screwdriver, reinstall the latch plate, latch

backing plate, and hinge assembly on the opposite sides from

which they were removed.

Using a TORX ®T25®screwdriver, remove the 4 screws on the

dryer. Insert the tabs on the hinge into the mounting slot and

slide down to engage the top tab. Secure in place with the

4 TORX ®T25®screws removed earlier.

Reverse door swing round-shaped door = double handle

1, Remove door from dryer

® ®

iMPORTANT: If the protective film has not yet been removed

from the dryer, peel the film from the dryer door before

proceeding.

Using a TORX®T25®screwdriver, remove the 4 screws

securing the door hinge to the dryer and lift up and out to

remove the door. Place the door on a soft towel or other

non-scratch surface. Reinstall the 4 screws in the holes.

® ®

Using a TORX®T25 ®screwdriver, remove the 2 screws

securing the door strike to the door frame of the dryer. Rotate

the strike 180° and attach to the opposite side of dryer door

frame, as shown.

3. Remove inner door from outer door

Position the door with the inside of the door facing up.

Using a Phillips screwdriver, remove the 10 screws securing

the inner door to the outer door. Lift off the inner door and

set aside.

4. Remove hinge and latch

g Latch

Hinge

Using a TORX®T25®screwdriver, remove the 3 TORX®screws

securing the latch plate and latch backing plate and the 5

screws holding the hinge assembly in place.

Reinstall hinge and latch on

opposite sides

Using a TORX ®T25®screwdriver, reinstall the latch plate and

latch backing plate with the 3 TORX ®screws removed earlier

and the hinge assembly with the 5 screws on the opposite

sides from which they were removed.

6, Reinstall inner door assembly

Bottom

of door

Position the door with the inside of the door facing up.

Reinstall the 10 screws securing the inner door to the

outer door.

Using a TORX ®T25®screwdriver, remove the 4 screws on the

dryer. Insert the tabs on the hinge into the mounting slot and

slide down to engage the top tab. Secure in place with

the 4 TORX ®T25®screws removed earlier.

Reverse door swing square-shaped door

1, Remove door from dryer

Using a TORX®T25®screwdriver, remove the 4 screws

securing the door hinge to the dryer and lift up and out to

remove the door. Place the door on a soft towel or other

non-scratch surface. Retain or set aside the 4 screws.

La page charge ...

Whirlpool MGD7100DC0 Guide d'installation

Marque: Whirlpool

Modèle: MGD7100DC0

Catégorie: Sèche-linge

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool MGD7100DC0 Installation guide

Whirlpool MGD7100DC0 Guide d'installation

Whirlpool MGD7100DC0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents