Briggs & Stratton 20341 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 20341

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Ce manuel convient également à

020341-0

Manual No. 204571GS Revision A (04/15/2008)

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

Pressure Washer

Operator’s Manual

This pressure washer is rated in accordance to the Pressure Washer Manufacture Association

(PWMA) standard PW101 (Testing and Rating Performance of Pressure Washers).

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

reproduced or transmitted in any form by any means without

the express written permission of Briggs & Stratton Power

Products Group, LLC.

Thank you for purchasing this quality-built Briggs & Stratton pressure washer. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your

Briggs & Stratton pressure washer will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with pressure washers and

how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this pressure washer could be

used for, it is important that you read and understand these instructions thoroughly before attempting to start or operate this

equipment. Save these instructions for future reference.

This pressure washer requires final assembly before use. Refer to the Assembly section of this manual for instructions on

final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your pressure washer. Consult your Yellow Pages.

There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also

contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at BRIGGSandSTRATTON.COM.

Pressure Washer

Model Number

Revision

Serial Number

Engine

Model Number

Type Number

Code Number

Date Purchased

Table of Contents
Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety Rules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Unpack Pressure Washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Attach Handle and Accessory Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Add Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Add Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connect Hose and Water Supply to Pump. . . . . . . . . . . . . . . . . . . . . . . . . 10
Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Pressure Washer Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Start Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
How to Stop Your Pressure Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
How to Use Spray Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Applying Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Pressure Washer Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning Detergent Siphoning Tube. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Automatic Cool Down System (Thermal Relief). . . . . . . . . . . . . . . . . . . . . 16
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Pressure Washer Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Engine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
After Each Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Winter Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Long Term Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Warranties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Emissions Control System Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Pressure Washer Owner Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3
Français

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your pressure washer. Know its applications,

its limitations, and any hazards involved.

This pressure washer operates at a maximum of 2,800 PSI

(193 BARS) and a flow rate of up to 2.5 gallons per minute

(9.4 liters per minute). This high quality residential system

features an axial cam pump with stainless steel pistons,

automatic cool down system, detergent siphoning system,

nozzle extension with quick connect fitting, a variety of quick

connect spray tips, safety goggles, heavy duty 30’ (9.1 m)

hose, and more.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

The Emission Control System for this pressure washer is

warranted for standards set by the Environmental Protection

Agency and the California Air Resources Board.

Safety Rules

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all

safety messages that follow this symbol to avoid

possible injury or death.

The safety alert symbol ( ) is used with a signal word

(DANGER, CAUTION, WARNING), a pictorial and/or a safety

message to alert you to hazards. DANGER indicates a hazard

which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury. CAUTION indicates a hazard

which, if not avoided, might result in minor or moderate

injury. NOTICE indicates a situation that could result in

equipment damage. Follow safety messages to avoid or

reduce the risk of injury or death.

Hazard Symbols and Meanings

A - Explosion G - Flying Objects

B - Fire H - Slippery Surface

C - Electric Shock I - Fall

D - Toxic Fumes J - Fluid Injection

E - Kickback K - Moving Parts

F - Hot Surface L - Read Manual

4 BRIGGSandSTRATTON.COM

A B C

D E

G H

J K L

WARNING

The engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth

defects, or other reproductive harm.

WARNING

Risk of electrocution.

Contact with power source can cause electric

shock or burn.

• NEVER spray near power source.

WARNING

Use of pressure washer can create puddles and

slippery surfaces.

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• The cleaning area should have adequate slopes and drainage to

reduce the possibility of a fall due to slippery surfaces.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING OR DRAINING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• DO NOT spray flammable liquids.

WHEN TRANSPORTING OR REPAIRING EQUIPMENT

• Transport/repair with fuel tank EMPTY or with fuel shutoff valve

OFF.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes dryers,

or other appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

Some chemicals or detergents may be harmful if

inhaled or ingested, causing severe nausea,

fainting, or poisoning.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area, even

if windows and doors are open.

• Use a respirator or mask whenever there is a chance that vapors

may be inhaled.

• Read all instructions with mask so you are certain the mask will

provide the necessary protection against inhaling harmful

vapors.

WARNING

Certain components in this product and related

accessories contain chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

6 BRIGGSandSTRATTON.COM

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of pressure

washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE

WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt and

then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate pressure washer.

• NEVER repair high pressure hose. Replace it.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button and

squeeze spray gun trigger, to release high pressure, every time

you stop engine.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

NOTICE

High pressure spray may damage fragile items including

glass.

• DO NOT point spray gun at glass when using red 0° spray tip.

• NEVER aim spray gun at plants.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

WARNING

Starter and other rotating parts can entangle

hands, hair, clothing, or accessories.

• NEVER operate pressure washer without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• If you have questions about intended use, ask dealer or contact

qualified service center.

• NEVER operate units with broken or missing parts, or without

protective housing or covers.

• DO NOT by-pass any safety device on this machine.

• DO NOT tamper with governed speed.

• DO NOT operate pressure washer above rated pressure.

• DO NOT modify pressure washer in any way.

• Before starting pressure washer in cold weather, check all parts

of the equipment to be sure ice has not formed there.

• NEVER move machine by pulling on hoses. Use handle provided

on unit.

• Check fuel system for leaks or signs of deterioration, such as

chafed or spongy hose, loose or missing clamps, or damaged

tank or cap. Correct all defects before operating pressure

washer.

• This equipment is designed to be used with Briggs & Stratton

Power Products authorized parts ONLY. If equipment is used

with parts that DO NOT comply with minimum specifications,

user assumes all risks and liabilities.

Assembly

Read entire operator’s manual before you attempt

to assemble or operate your new pressure washer.

Your pressure washer requires some assembly and is ready

for use after it has been properly serviced with the

recommended oil and fuel.

If you have any problems with the assembly of your pressure

washer, please call the pressure washer helpline at

(800) 743-4115. If calling for assistance, please have the

model, revision, and serial number from the identification

label available.

Unpack Pressure Washer

1. Remove the parts bag, accessories, and inserts

included with pressure washer.

2. Open carton completely by cutting each corner from

top to bottom.

3. Ensure you have all included items prior to assembly.

Items in the carton include:

• Main Unit

• Handle

• High Pressure Hose

• Spray Gun

• Nozzle Extension with Quick Connect Fitting

• Plastic Accessory Tray

• Oil Bottle

• Parts Bag (which includes the following):

• Safety Goggles

• Operator’s Manual

• Owner’s Registration Card

• Bag of 4 Multi–Colored Spray Tips

• Handle/Accessory Tray Fastening Hardware Kit

(which includes):

• Carriage Bolts (2)

• Plastic Knobs (2)

• Tree Clips (4)

To prepare your pressure washer for operation, you will

need to perform these tasks:

1. Fill out and send in registration card.

2. Attach handle and accessory tray to main unit.

3. Add oil to engine crankcase.

4. Add fuel to fuel tank.

5. Connect high pressure hose to spray gun and pump.

6. Connect water supply to pump.

7. Attach nozzle extension to spray gun.

8. Select/attach quick connect spray tip to nozzle

extension.

Attach Handle and Accessory Tray

1. Place handle (A) onto handle supports (B) connected to

main unit. Make sure holes (C) in handle align with

holes (C) on handle supports.

NOTE: It may be necessary to move the handle supports

from side to side in order to align the handle so it will slide

over the handle supports.

2. Insert carriage bolts (D) through holes from back of

unit and attach a plastic knob (E) from front of unit.

Tighten by hand.

3. Place accessory tray (F) over holes (H) on handle

(viewing from front of unit). Push the tree clips (G) into

the holes until they sit flat against the accessory tray.

4. Insert multi–colored spray tips and other supplied

accessories in spaces provided in accessory tray. See

How to Use Accessory Tray.

8 BRIGGSandSTRATTON.COM

Add Engine Oil

1. Place pressure washer on a flat, level surface.

2. Clean area around oil fill and remove yellow oil fill

cap/dipstick.

3. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening.

4. Replace oil fill cap/dipstick and fully tighten.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High

altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems

after using fuel, switch to a different fuel provider or change

brands. This engine is certified to operate on gasoline. The

emission control system for this engine is EM (Engine

Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add regular unleaded fuel (A) to fuel tank (B). Be

careful not to overfill. Allow about 1.5" (4 cm) (C) of

tank space for fuel expansion.

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane / 85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See a Briggs and Stratton authorized dealer for

high altitude adjustment information. Operation of the engine

at altitudes below 2,500 feet (762 meters) with the high

altitude kit is not recommended.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• DO NOT attempt to crank or start the engine before it has been

properly serviced with the recommended oil. This may result in

an engine failure.

NOTICE

Avoid pressure washer damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

WARNING

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or

death.

WHEN ADDING FUEL

• Turn pressure washer OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve pressure

in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

Connect Hose and Water Supply to Pump

NOTE: Remove and discard the shipping caps from the

pump’s high pressure outlet and water inlet before attaching

hoses.

1. Uncoil high pressure hose and attach one end of hose

to base of spray gun. Tighten by hand.

2. Attach other end of high pressure hose to high

pressure outlet on pump (A). Tighten by hand.

3. Run water through your garden hose for 30 seconds to

clean out any debris.

IMPORTANT: DO NOT siphon standing water for the water

supply. Use ONLY cold water (less than 100°F (38°C)).

4. Before connecting garden hose to water inlet, inspect

inlet screen (A). Clean screen if it contains debris or

have it replaced if damaged. DO NOT run pressure

washer if inlet screen is damaged.

5. Connect the garden hose (not to exceed 50 feet (15 m)

in length) to the water inlet. Tighten by hand.

6. Turn ON the water. Press red button (B) and squeeze

the trigger on the gun to purge the pump system of air

and impurities.

Checklist Before Starting Engine

Review the unit’s assembly to ensure you have performed all

of the following.

1. Be sure to read the Operator Safety section and How to

Use Your Pressure Washer in Operation section before

using pressure washer.

2. Make sure handle is in place and secure.

3. Check that oil has been added to proper level in the

engine crankcase.

4. Add proper fuel to fuel tank.

5. Check for properly tightened hose connections.

6. Check to make sure there are no kinks, cuts, or damage

to high pressure hose.

7. Provide a proper water supply at an adequate flow.

10 BRIGGSandSTRATTON.COM

NOTICE

DO NOT run the pump without the water supply connected

and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER connect high pressure hose to nozzle extension.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

NOTICE

Damage to pump or water inlet connector will occur if a

One Way Valve (vacuum breaker or check valve) is

connected to pump.

• There MUST be at least ten feet (3M) of unrestricted garden

hose between the pressure washer inlet and any device, such as

a One Way Valve.

• Damage to equipment caused by attaching a One Way Valve to

pump will void warranty.

Features and Controls

Read this Operator’s Manual and safety rules before operating your pressure washer.

Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A- Spray Tips— Detergent, 0°, 15° and 40°: for various high

pressure cleaning applications.

B - Spray Gun — Controls the application of water onto

cleaning surface with trigger device. Includes trigger lock.

C - Accessory Tray — Provides convenient storage for

standard and optional accessories, such as brushes,

turbo wands, etc.

D - Warning/Operating Instructions Tag — Identifies

hazards and proper procedure to start/stop pressure

washer.

E - Nozzle Extension with Quick Connect — Allows you to

switch between four different nozzles.

F - Choke Lever — Prepares a cold engine for starting.

G - Air Filter — Protects engine by filtering dust and debris

out of intake air.

H - Recoil Starter — Used for starting the engine manually.

J - High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

K - Fuel Valve — Used to turn fuel supply on and off to

engine.

L - Throttle Lever — Sets engine in starting mode for recoil

starter and stops a running engine.

M - Fuel Tank — Fill tank with regular unleaded fuel. Always

leave room for fuel expansion.

N - Detergent Siphoning Tube/Filter — Use to siphon

pressure washer safe detergents into the low pressure

stream.

P - Pump — Develops high pressure.

R - Automatic Cool Down System — Cycles water through

pump when water reaches 125°-155°F. Warm water will

discharge from pump onto ground. This system prevents

internal pump damage.

S - Oil Drain — Drain engine oil here.

T - Oil Fill — Check and add engine oil here.

U - High Pressure Outlet — Connection for high pressure

hose.

V - Water Inlet — Connection for garden hose.

Items Not Shown:

Identification Label (under base plate) — Provides model

and serial number of pressure washer. Please have these

readily available if calling for assistance.

12 BRIGGSandSTRATTON.COM

Operation

If you have any problems operating your pressure washer,

please call the pressure washer helpline at (800) 743-4115.

Pressure Washer Location

Clearances and Air Movement

Place pressure washer outdoors in an area that will not

accumulate deadly exhaust gas. DO NOT place pressure

washer where exhaust gas (A) could accumulate and enter

inside or be drawn into a potentially occupied building.

Ensure exhaust gas is kept away from any windows, doors,

ventilation intakes, or other openings that can allow exhaust

gas to collect in a confined area. Prevailing winds and air

currents should be taken into consideration when positioning

pressure washer.

How to Start Your Pressure Washer

To start your pressure washer for the first time, follow these

instructions step-by-step. This starting information also

applies if you have let the pressure washer sit idle for at least

a day.

1. Place pressure washer near an outside water source

capable of supplying water at a flow rate greater than

3.5 gallons (13.2 l) per minute and no less than 20 PSI

(1.38 BARS) at pressure washer end of garden hose.

DO NOT siphon supply water.

2. Check that high pressure hose is tightly connected to

spray gun and pump. See Assembly section.

3. Make sure unit is in a level position.

4. Connect garden hose to water inlet on pressure washer

pump.

5. Turn ON water, point gun in a safe direction and press

red button and squeeze trigger to purge pump system of

air and impurities.

6. Attach nozzle extension to spray gun. Tighten by hand.

7. Choose spray tip you want to use, pull back on collar of

nozzle extension, insert spray tip and release collar. Tug

on spray tip to make sure it is securely in place. See

How to Use Spray Tips.

WARNING

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• Keep at least 5 ft. (1.5 m) clearance on all sides of pressure

washer including overhead.

WARNING

Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate pressure washer ONLY outdoors.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area, even

if windows and doors are open.

NOTICE

DO NOT run the pump without the water supply connected

and turned on.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

8. Rotate fuel shut-off valve to “On” position (A) (fully

counter-clockwise).

9. Move throttle control lever (B) to “High” position,

shown on engine as a rabbit .

10. Move choke lever to “Choke” position.

NOTE: For a warm engine, be sure the choke lever is in the

“Run” position.

IMPORTANT: Before starting the pressure washer, be sure

you are wearing adequate safety goggles.

11. When starting engine, position yourself as

recommended and grasp starter grip handle and pull

slowly until you feel some resistance. Then pull rapidly

to start engine.

12. Return starter grip handle slowly. DO NOT let rope

“snap back” against starter.

13. When engine starts, slowly move choke lever to “Run”

position, as engine warms. If engine falters, move choke

lever to “Choke” position, then to “Run” position.

14. After each starting attempt, where engine fails to run,

always point gun in safe direction and press red button

and squeeze spray gun trigger to release high pressure.

Move choke lever to “Choke” position, and repeat

steps 11 through 13.

15. If engine fails to start after six pulls, move choke lever

to “Run” position, and repeat steps 11 through 13.

NOTE: Always keep the throttle lever in the “Fast”

position when operating the pressure washer.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• DO NOT allow CHILDREN to operate pressure washer.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• NEVER aim spray gun at people, animals, or plants.

• DO NOT secure spray gun in open position.

• DO NOT leave spray gun unattended while machine is running.

• NEVER use a spray gun which does not have a trigger lock or

trigger guard in place and in working order.

• Always be certain spray gun, nozzles and accessories are

correctly attached.

WARNING

Risk of eye injury.

Spray can splash back or propel objects.

• Always wear safety goggles when using this equipment or in

vicinity of where equipment is in use.

• Before starting the pressure washer, be sure you are wearing

adequate safety goggles.

• NEVER substitute safety glasses for safety goggles.

WARNING

Starter cord kickback (rapid retraction) can result

in bodily injury. Kickback will pull hand and arm

toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• NEVER pull starter cord without first relieving spray gun

pressure.

• When starting engine, pull cord slowly until resistance is felt and

then pull rapidly to avoid kickback.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

14 BRIGGSandSTRATTON.COM

How to Stop Your Pressure Washer

1. Release spray gun trigger and let engine idle for two

minutes.

2. Move throttle to SLOW position, then STOP

position (A).

3. ALWAYS point gun in a safe direction and press red

button and squeeze spray gun trigger to release

retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

How to Use Accessory Tray

The unit is equipped with an accessory tray with places to

store your spray gun, nozzle extension and spray tips. There

is also a hook at the front of the accessory tray to hold your

high pressure hose.

NOTE: The extra hole in the tray is for storing a utility brush.

The extra clip in the tray is for storing a turbo nozzle. The

brush and turbo nozzle are NOT included with your pressure

washer. You can buy these items as optional accessories.

1. Place nozzle extension through hole on accessory tray

as shown.

2. Place spray gun through hole on accessory tray on

right side of unit as shown.

3. Hang high pressure hose on hook attached to

accessory tray on front of tray as shown.

4. Insert multi–colored spray tips in spaces provided in

accessory tray.

WARNING

Contact with muffler area can result in serious

burns.

Exhaust heat/gases can ignite combustibles,

structures or damage fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of pressure

washer including overhead.

• Code of Federal Regulation (CFR) Title 36 Parks, Forests, and

Public Property require equipment powered by an internal

combustion engine to have a spark arrester, maintained in

effective working order, complying to USDA Forest service

standard 5100-1C or later revision. In the State of California a

spark arrester is required under section 4442 of the California

Public resources code. Other states may have similar laws.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• After each starting attempt, where engine fails to run, always

point spray gun in safe direction, press red button and squeeze

spray gun trigger to release high pressure.

How to Use Spray Tips

The quick–connect on the nozzle extension allows you to

switch between four different quick connect spray tips. Spray

tips can be changed while pressure washer is running once

spray gun trigger lock is engaged. The spray tips vary the

spray pattern as shown below.

Follow these instructions to change spray tips:

1. Pull back collar on quick–connect and pull current

spray tip off. Store spray tips in holes provided in the

accessory tray.

2. Select desired spray tip:

• For gentle rinse, select white 40° spray tip.

• To scour surface, select yellow 15° or red 0° spray tip.

• To apply detergent, select black spray tip.

3. Pull back on collar, insert new spray tip and release collar.

Tug on spray tip to make sure it is securely in place.

Usage Tips

• For most effective cleaning, keep spray tip from 8 to

24 inches (20 to 61 cm) away from cleaning surface.

• If you get spray tip too close, especially using a high

pressure spray tip, you may damage surface being

cleaned.

• DO NOT get closer than 6 inches (15 cm) when

cleaning tires.

Applying Detergent

To apply detergent, follow these steps:

1. Review use of spray tips.

2. Prepare detergent solution as required by job.

3. Place small filter end of detergent siphoning tube into

detergent container.

NOTE: Make sure the filter is fully submerged in detergent

while applying detergent.

4. Make sure black spray tip is installed.

NOTE: Detergent cannot be applied with the high pressure

spray tips (White, Yellow or Red).

5. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

6. Start engine following instructions How to Start Your

Pressure Washer.

7. Apply detergent to a dry surface, starting at lower

portion of area to be washed and work upward, using

long, even, overlapping strokes.

8. Allow detergent to "soak in" for 3-5 minutes before

washing and rinsing. Reapply as needed to prevent

surface from drying. DO NOT allow detergent to dry on

(prevents streaking).

IMPORTANT: You must flush the detergent siphoning

system after each use by placing the filter into a bucket of

clean water, then run the pressure washer in low pressure

for 1-2 minutes.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER exchange spray tips without locking the trigger lock on

the spray gun.

• DO NOT twist spray tips while spraying.

40° White 15° Yellow 0° Red

Black

Use to apply

chemical

Low Pressure

High Pressure

CAUTION

Chemicals can cause bodily injury, and/or property

damage.

• NEVER use caustic liquid with pressure washer.

• Use ONLY pressure washer safe detergents/soaps. Follow all

manufacturers instructions.

NOTICE

Contact with the hot muffler can damage detergent

siphoning tube.

• When inserting the filter into a detergent solution bottle, route

the tube so as to keep it from inadvertently contacting the hot

muffler.

NOTICE

You must attach all hoses before you start the engine.

• Starting the engine without all the hoses connected and without

the water turned ON will damage the pump.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

16 BRIGGSandSTRATTON.COM

Pressure Washer Rinsing

For Rinsing:

1. Remove black spray tip from nozzle extension.

2. Select and install desired high pressure spray tip

following instructions How to Use Spray Tips.

3. Keep the spray gun a safe distance from the area you

plan to spray.

4. Apply a high pressure spray to a small area, then check

the surface for damage. If no damage is found, it is

okay to continue cleaning.

5. Start at the top of the area to be rinsed, working down

with same overlapping strokes as you used for washing

and applying detergent.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it

with clean water before stopping the engine.

1. Place detergent siphoning tube/filter in a bucket full of

clean water.

2. Remove high pressure spray tip from nozzle extension.

3. Select and install black detergent spray tip following

instructions How to Use Spray Tips.

4. Flush for 1-2 minutes.

5. Shut off engine following instructions How to Stop

Pressure Washer and turn off water supply.

6. ALWAYS point spray gun in a safe direction, press red

button and squeeze spray gun trigger to release

retained high water pressure.

IMPORTANT: Spray gun traps high water pressure, even

when engine is stopped and water is disconnected.

Automatic Cool Down System (Thermal Relief)

If you run the engine on your pressure washer for

3-5 minutes without pressing the trigger on the spray gun,

circulating water in the pump can reach temperatures above

125°F (51°C). The system engages to cool the pump by

discharging the warm water onto the ground.

WARNING

Kickback from spray gun can cause you to fall.

• Operate pressure washer from a stable surface.

• Be extremely careful if you must use the pressure washer from

a ladder, scaffolding, or any other similar location.

• Firmly grasp spray gun with both hands when using high

pressure spray to avoid injury when spray gun kicks back.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button and

squeeze spray gun trigger, to release high pressure, every time

you stop engine.

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Clean if clogged. Replace if perforated or torn.

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any qualified

dealer for service.

The pressure washer’s warranty does not cover items that

have been subjected to operator abuse or negligence. To

receive full value from the warranty, the operator must

maintain the pressure washer as instructed in this manual,

including proper storage as detailed in Winter Storage and

Long Term Storage.

NOTE: Should you have questions about replacing

components on your pressure washer, please call

(800) 743-4115 for assistance.

Some adjustments will need to be made periodically to

properly maintain your pressure washer.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart above.

NOTE: Once a year you should clean or replace the spark

plug, clean or replace the air filter, and check the spray gun

and nozzle extension assembly for wear. A new spark plug

and clean air filter assure proper fuel-air mixture and help

your engine run better and last longer.

Pump Oil

DO NOT attempt any oil maintenance on this pump. The

pump is pre-lubricated and sealed from the factory, requiring

no additional maintenance for the life of the pump.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See the Emissions Warranty.

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Check/clean water inlet screen

• Check high pressure hose

• Check detergent siphoning hose

• Check spray gun and assembly for leaks

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service air cleaner

Every 50 Hours or Yearly

• Change engine oil

• Service spark arrester

Every 100 Hours or Yearly

• Service spark plug

• Air cooling system

18 BRIGGSandSTRATTON.COM

Before Each Use

1. Check engine oil level.

2. Clean debris.

3. Check water inlet screen for damage.

4. Check high pressure hose for leaks.

5. Check detergent siphoning tube/fiter for damage.

6. Check spray gun and nozzle extension assembly for

leaks.

7. Rinse out garden hose to flush out debris.

Pressure Washer Maintenance

Clean Debris

Daily or before use, clean accumulated debris from cleaning

system. Keep linkage, spring and controls clean. Keep area

around and behind muffler free from any combustible debris.

Inspect cooling air slots and openings on the pressure

washer. These openings must be kept clean and

unobstructed.

Pressure washer parts should be kept clean to reduce the

risk of overheating and ignition of accumulated debris.

• Use a damp cloth to wipe exterior surfaces clean.

• Use a soft bristle brush to loosen caked on dirt, oil, etc.

• Use a vacuum cleaner to pick up loose dirt and debris.

Check and Clean Inlet Screen

Examine the screen on the pump’s water inlet. Clean it if the

screen is clogged or replace it if screen is damaged.

Check High Pressure Hose

The high pressure hose can develop leaks from wear,

kinking, or abuse. Inspect the hose each time before using it.

Check for cuts, leaks, abrasions or bulging of cover, damage

or movement of couplings. If any of these conditions exist,

replace the hose immediately.

Check Detergent Siphoning Tube

Examine the filter on the detergent tube and clean if clogged.

The tube should fit tightly on the barbed fitting. Examine the

tube for leaks or tears. Replace the filter or tube if either is

damaged.

Check Gun and Nozzle Extension

Examine the hose connection to the spray gun and make

sure it is secure. Test the trigger by pressing the red button

and making sure the trigger “springs back” into place when

you release it. You should not be able to press the trigger

without pressing the red button. Replace spray gun

immediately if it fails any of these tests.

Nozzle Maintenance

A pulsing sensation felt while squeezing the spray gun

trigger may be caused by excessive pump pressure. The

principal cause of excessive pump pressure is a spray tip

clogged or restricted with foreign materials, such as dirt, etc.

To correct the problem, immediately clean the spray tip

following these instructions:

1. Shut off engine and turn off water supply.

2. ALWAYS point spray gun in a safe direction, press red

button and squeeze spray gun trigger to release

retained high water pressure.

3. Remove spray tip from end of nozzle extension.

4. Use a small paper clip to free any foreign material

clogging or restricting spray tip (A).

5. Remove nozzle extension from spray gun.

NOTICE

Improper treatment of pressure washer can damage it and

shorten its life.

• DO NOT insert any objects through cooling slots.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER repair high pressure hose. Replace it.

• Replacement hose rating MUST exceed maximum pressure

rating of unit.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

Spray gun traps high water pressure, even when

engine is stopped and water is disconnected,

which can cause injury.

• Keep high pressure hose connected to pump and spray gun

while system is pressurized.

• ALWAYS point spray gun in safe direction, press red button and

squeeze spray gun trigger, to release high pressure, every time

you stop engine.

6. Using a garden hose, remove additional debris by back

flushing water through nozzle extension. Back flush

between 30 to 60 seconds.

7. Reinstall spray tip into nozzle extension.

8. Reconnect nozzle extension to spray gun.

9. Make sure garden hose is connected to water inlet.

Check that high pressure hose is connected to spray

gun and pump. Turn on water.

10. Start engine following instructions How to Start Your

Pressure Washer.

11. Test pressure washer by operating with each quick

connect spray tip.

O-Ring Maintenance

Purchase an O-Ring/Maintenance Kit, model 6048, by

contacting the nearest authorized service center. It is not

included with the pressure washer. This kit includes

replacement o-rings, rubber washer and water inlet filter.

Refer to the instruction sheet provided in the kit to service

your unit’s o-rings.

Engine Maintenance

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

NOTE: Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol with

“SJ/CF ENERGY CONSERVING” or higher, is an

acceptable oil at all temperatures. Use of synthetic

oil does not alter required oil change intervals.

WARNING

The high pressure stream of water that this

equipment produces can cut through skin and its

underlying tissues, leading to serious injury and

possible amputation.

• NEVER repair leaking connections with sealant of any kind.

Replace o-ring or seal.

WARNING

Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR PRESSURE

WASHER

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

20 BRIGGSandSTRATTON.COM

Checking Oil Level

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure pressure washer is on a level surface.

2. Remove oil dipstick and wipe dipstick with clean cloth.

Replace and tighten dipstick. Remove and check oil level.

3. Verify oil is at “Full” mark on dipstick. Replace and

tighten dipstick.

Adding Engine Oil

1. Make sure pressure washer is on a level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the

“Full” mark on dipstick. DO NOT overfill.

4. Replace and tighten dipstick.

Changing Engine Oil

Change the engine oil after the first 5 hours and every

50 hours thereafter. If you are using your pressure washer

under extremely dirty or dusty conditions, or in extremely

hot weather, change the oil more often.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change oil while engine is still warm from running, as

follows:

1. Make sure unit is on a level surface.

2. Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

3. Clean area around oil drain plug. The oil drain plug is

located at base of engine, opposite carburetor.

4. Remove oil drain plug and drain oil completely into a

suitable container.

5. Reinstall oil drain plug and tighten securely. Remove oil

fill cap/dipstick.

6. Slowly pour oil (about 20 oz.) into oil fill opening to the

“Full” mark on dipstick. DO NOT overfill.

7. Replace and tighten oil fill cap/dipstick.

8. Wipe up any spilled oil.

Service Air Cleaner

Your engine will not run properly and may be damaged if

you run it with a dirty air cleaner.

Service the air cleaner once every 25 hours of operation or

once each year, whichever comes first. Service more often if

operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen screw (A) and tilt cover (B) down.

2. Carefully remove cartridge (C) assembly.

3. To clean cartridge, gently tap pleated paper side on a

flat surface.

4. Reinstall clean or new cartridge assembly inside cover.

5. Insert cover’s tabs (D) into slots in bottom of base (E).

6. Tilt cover up and tighten screw securely to base.

Service Spark Plug

Change the spark plug every 100 hours of operation or once

each year, whichever comes first. This will help your engine

to start easier and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Check electrode gap with wire feeler gauge and set

spark plug gap to 0.030 inch (0.76 mm) if necessary.

CAUTION

Avoid prolonged or repeated skin contact with used motor

oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

NOTICE

Overfilling with oil may cause the engine to not start, or

hard starting.

• DO NOT overfill.

• If over the FULL mark on dipstick, drain oil to reduce oil level to

FULL mark on dipstick.

La page charge ...

Briggs & Stratton 20341 Manuel utilisateur

Marque: Briggs & Stratton

Modèle: 20341

Catégorie: Nettoyeurs haute pression

Taper: Manuel utilisateur

Ce manuel convient également à

020341-0

Télécharger le PDF

rapport

dans d''autres langues

English: Briggs & Stratton 20341 User manual