VTech CS6214-21 Guide de démarrage rapide

Marque: VTech

Modèle: CS6214-21

Taper: Guide de démarrage rapide

Ce manuel convient également à

Connect the telephone base

Speciﬁcations are subject to change without notice.

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of the

Telecommunications Industry Association. Used under license.

Compatible with

Hearing Ai

d T-Coil

TIA-1083 The ENERGY STAR® program (www.energystar.gov) recognizes and

encourages the use of products that save energy and help protect our

environment. We are proud to mark this product with the ENERGY

STAR® label indicating it meets the latest energy efﬁciency guidelines.

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Handset: 1921.536-1928.448 MHz

Telephone Base: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal

effective

range

Maximum power allowed by FCC and IC.

Actual operating range may vary according to

environmental conditions at the time of use.

Power

requirement Handset: 2.4V Ni-MH battery

Telephone base: 6V DC @ 400mA

Charger: 6V DC @ 400mA

Memory Directory: 30 memory locations;

up to 30 digits and 15 characters

Caller ID log: 30 memory locations;

up to 24 digits and 15 characters

If you subscribe to digital subscriber line (DSL) high-speed Internet

service through your telephone line, make sure you connect a DSL

ﬁlter (not included) to the telephone wall jack.

Go to www.vtechphones.com to register your

product for enhanced warranty support and latest

VTech product news.

Go to phones.vtechcanada.com (Canada) for latest

VTech product news.

Quick start guide

CS6214

CS6214-2

CS6214-11

CS6214-21

DECT 6.0 cordless telephone

Quick

start

guide

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

THIS SIDE UP

Install the battery

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1939

Connect the charger Charge the battery

12 hrs

The battery is low and needs charging.

The battery is charging.

The battery is fully charged.

New voicemail received from your telephone

service provider.

NEW

There are new caller ID log entries.

HANDSET

NEW

10:15.pm12/25

Display

After you install your telephone or power returns following

a power outage and battery depletion, the handset will

prompt you to set the date and time.

Press SELECT.

Enter the time.

Press SELECT.

When the handset

prompts you to set

the date and time

Directory

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed

to reduce the risk of ﬁre, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

4. CAUTION: Do not install the telephone base at a height above 2 meters.

5. Do not use this product near water such as near a bath tub, wash bowl, kitchen sink,

laundry tub or a swimming pool, nor in a wet basement or shower.

6. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

7. Avoid placing the telephone system in places with extreme temperature, direct sunlight,

or other electrical devices. Protect your phone from moisture, dust, corrosive liquids and

fumes.

8. Slots and openings in the back or bottom of the telephone base and handset are provided

for ventilation. To protect them from overheating, these openings must not be blocked by

placing the product on a soft surface such as a bed, sofa or rug. This product should never

be placed near or over a radiator or heat register. This product should not be placed in any

area where proper ventilation is not provided.

9. This product should be operated only from the type of power source indicated on the

marking label. If you are not sure of the type of power supply in your home or ofﬁce,

consult your dealer or local power company.

10. Do not allow anything to rest on the power cord. Do not install this product where the cord

may be walked on.

11. Never push objects of any kind into this product through the slots in the telephone base or

handset because they may touch dangerous voltage points or create a short circuit. Never

spill liquid of any kind on the product.

12. To reduce the risk of electric shock, do not disassemble this product, but take it to an

authorized service facility. Opening or removing parts of the telephone base or handset

other than speciﬁed access doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the product is subsequently used.

13. Do not overload wall outlets and extension cords.

14. Unplug this product from the wall outlet and refer servicing to an authorized service facility

under the following conditions:

• When the power supply cord or plug is damaged or frayed.

• If liquid has been spilled onto the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operation instructions. Improper

adjustment of other controls may result in damage and often requires extensive work

by an authorized technician to restore the product to normal operation.

• If the product has been dropped and the telephone base and/or handset has been

damaged.

• If the product exhibits a distinct change in performance.

15. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote

risk of electric shock from lightning.

16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under certain

circumstances, a spark may be created when the adapter is plugged into the power

outlet, or when the handset is replaced in its cradle. This is a common event associated

with the closing of any electrical circuit. The user should not plug the phone into a power

outlet, and should not put a charged handset into the cradle, if the phone is located in

an environment containing concentrations of ﬂammable or ﬂame-supporting gases,

unless there is adequate ventilation. A spark in such an environment could create a ﬁre or

explosion. Such environments might include: medical use of oxygen without adequate

ventilation; industrial gases (cleaning solvents; gasoline vapors; etc.); a leak of natural

gas; etc.

17. Only put the handset of your telephone next to your ear when it is in normal talk mode.

18. The power adapter is intended to be correctly oriented in a vertical or ﬂoor mount

position. The prongs are not designed to hold the plug in place if it is plugged into a

ceiling, under-the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall

be easily accessible.

20. CAUTION: Use only the batteries indicated in this manual. There may be a risk

of explosion if a wrong type of battery is used for the handset. Use only the supplied

rechargeable batteries or replacement batteries (BT162342/BT262342) for the handset.

Do not dispose of batteries in a ﬁre. They may explode.

21. Use only the adapter included with this product. Incorrect adapter polarity or voltage can

seriously damage the product.

SAVE THESE INSTRUCTIONS

Battery

• CAUTION: Use Only Supplied Battery.

• Do not dispose of the battery in a ﬁre. Check with local waste management codes for

special disposal instructions.

• Do not open or mutilate the battery. Released electrolyte is corrosive and may cause

burns or injury to the eyes or skin. The electrolyte may be toxic if swallowed.

• Exercise care in handling batteries in order not to create a short circuit with conductive

materials.

• Charge the battery provided with this product only in accordance with the instructions

and limitations speciﬁed in this manual.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless telephones):

Wireless Technology Research, LLC (WTR), an independent research entity, led a

multidisciplinary evaluation of the interference between portable wireless telephones and

implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six inches from the pacemaker.

• Should NOT place wireless telephones directly over the pacemaker, such as in a breast

pocket, when it is turned ON.

• Should use the wireless telephone at the ear opposite the pacemaker.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons

using wireless telephones.

About cordless telephones

• Privacy: The same features that make a cordless telephone convenient create some

limitations. Telephone calls are transmitted between the telephone base and the cordless

handset by radio waves, so there is a possibility that the cordless telephone conversations

could be intercepted by radio receiving equipment within range of the cordless handset.

For this reason, you should not think of cordless telephone conversations as being as

private as those on corded telephones.

• Electrical power: The telephone base of this cordless telephone must be connected to a

working electrical outlet. The electrical outlet should not be controlled by a wall switch.

Calls cannot be made from the cordless handset if the telephone base is unplugged,

switched off or if the electrical power is interrupted.

• Potential TV interference: Some cordless telephones operate at frequencies that may

cause interference to televisions and VCRs. To minimize or prevent such interference, do

not place the telephone base of the cordless telephone near or on top of a TV or VCR. If

interference is experienced, moving the cordless telephone farther away from the TV or

VCR often reduces or eliminates the interference.

• Rechargeable batteries: Exercise care in handling batteries in order not to create a

short circuit with conducting material such as rings, bracelets and keys. The battery or

conductor may overheat and cause harm. Observe proper polarity between the battery

and the battery charger.

• Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe manner.

Do not burn or puncture the battery. Like other batteries of this type, if burned or

punctured, they could release caustic material which could cause injury.

1Enter the date.

LCD language setting

If you accidentally set the LCD language to Spanish or French,

press MENU and then enter 364# to change the handset LCD

language back to English while the handset is not in use.

Press

End a call Adjust volume

Press

- OR -

For more support information

Mike Smith

800-595-9511

HANDSET

10:15p

12/25

NEW

Date: MM/DD/YY

Date: 12/2?/YY

Date: 12/25/19

Time: 1?:MM --

Time: 10:59 AM

Note: If you have skipped the prompt, you can set up again by

pressing MENU to enter Set date/time, and then follow the steps

above.

HANDSET

ECO

NEW

ANS ON

10:15

MSG#

5/10

NOTESNOTE

US CA

For operations and guides to help you using your telephone, and for

latest information and supports, go and check the online help topics

and online FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/cs6214 (US); OR phones.

vtechcanada.com (Canada)

• Scan the QR code on the right. Launch the camera app or QR code

scanner app on your smartphone or tablet. Hold the device’s camera

up to the QR code and frame it. Tap the notiﬁcation to trigger the

redirection of the online help.

- If the QR code is not clearly displayed, adjust your camera’s focus by

moving your device closer or further away until it is clear.

You can also call our Customer Support at 1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de blessures corporelles ou d’électrocution, suivez

toujours ces mesures préventives de base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les instructions.

2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.

3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas de

nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et légèrement humecté.

4. ATTENTION: Ne pas installer le socle téléphonique à une hauteur supérieure à 2 mètres.

5. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un évier

de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol humide ou sous la

douche.

6. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants. L’appareil

pourrait tomber et être sérieusement endommagé.

7. Évitez d’installer le système téléphonique dans les endroits soumis à une température

extrême, à la lumière directe du soleil ou à proximité immédiate d’autres appareils

électriques ou électroniques. Protégez votre téléphone contre les sources d’humidité, la

poussière, les vapeurs et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées à l’arrière

ou en dessous. Aﬁn d’empêcher la surchauffe, ces ouvertures ne doivent pas être

obstruées en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires.

Ne placez pas cet appareil à proximité d’un élément de chauffage ni d’une plinthe

électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet fermé qui ne

possède pas d’aération adéquate.

9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les étiquettes

de l’appareil. Si vous ne connaissez pas le voltage de votre maison, consultez votre

marchand ou votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans un endroit

sécuritaire, là où personne ne pourra trébucher sur la ligne d’alimentation ni le cordon

téléphonique modulaire.

11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil, car ils

pourraient toucher à des points de tension dangereux ou court-circuiter des pièces, ce qui

constituerait un risque d’incendie ou d’électrocution. N’échappez pas de liquides dans

l’appareil.

12. Aﬁn de réduire les risques d’électrocution, ne démontez pas l’appareil, mais apportez-le

plutôt à un centre de service qualiﬁé s’il doit être réparé. En enlevant le couvercle, vous

vous exposez à des tensions dangereuses ou autres dangers similaires. Un remontage

inadéquat peut être à l’origine d’une électrocution lors d’une utilisation ultérieure de

l’appareil. Débranchez l’appareil avant de procéder au nettoyage. Utilisez un chiffon

humide et doux.

13. Ne surchargez pas les prises de courant et les rallonges.

14. Débranchez cet appareil de la prise de courant et communiquez avec le département de

service à la clientèle de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est endommagé ou écorché.

• Si du liquide a été échappé dans l’appareil.

• Si l’appareil a été exposé à une source d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas normalement en respectant les instructions de

fonctionnement. Réglez uniquement les commandes indiquées dans le les

instructions de fonctionnement. Les réglages incorrects des autres commandes

pourraient provoquer un dommage qui pourrait exiger un travail exhaustif de la part

d’un technicien autorisé aﬁn de rétablir le fonctionnement normal de l’appareil.

• Si le produit a été échappé et que le socle et/ou le combiné a été endommagé.

• Si le produit afﬁche une nette diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre qu’un sans ﬁl) pendant un orage. Les éclairs peuvent

être à l’origine d’une électrocution.

16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de la fuite. En

certaines circonstances, une ﬂammèche pourrait être provoquée lorsque l’adaptateur

est branché à une prise de courant, ou lorsque le combiné est déposé sur le socle. Ceci

est un événement commun associé à la fermeture d’un circuit électrique. L’utilisateur

ne devrait pas brancher le téléphone à une prise de courant, et ne devrait pas déposer

le combiné chargé sur le socle, si le téléphone se trouve à proximité d’un endroit

comportant des concentrations de gaz inﬂammables, à moins que la ventilation soit

adéquate. Une ﬂammèche dans un tel endroit pourrait provoquer un incendie ou une

explosion. De tels environnements peuvent comprendre: des endroits où l’on utilise

de l’oxygène médical sans ventilation adéquate; des gaz industriels (dissolvants de

nettoyage, des vapeurs d’essence, etc.); une fuite de gaz naturel, etc.

17. Ne placez que le combiné de votre téléphone près de votre oreille lorsqu’en mode de

conversation.

18. Ces adaptateurs ont été conçus pour être orientés en position verticale ou montés au

sol. Les broches ne sont pas conçues pour maintenir l’adaptateur en place si celui-ci est

barnché dans une prise au plafond ou sous une table/ armoire.

19. Pour le MATERIEL RACCORDE PAR PRISE DE COURANT, le socle de prise de courant doit

etre installe a proximite du materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y avoir un risque d’explosion si vous utilisez le mauvais

type de piles pour le téléphone. N’utilisez que les piles rechargeable inclus ou les piles

de rechange (BT162342/BT262342). N’incinérez pas les piles. Celles-ci risqueraient

d’exploser.

21. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un adaptateur dont la

polarité ou la tension serait inadéquate risque d’endommager sérieusement le produit et

mettre votre sécurité en péril.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou l’équivalent.

• Ne jetez pas la pile au feu. Vériﬁez les instructions spéciﬁques de mise aux rebus auprès

des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile. L’électrolyte qui s’en échapperait est corrosif et

pourrait causer des brûlures ou des blessures aux yeux ou à la peau. L’électrolyte est

toxique si avalé.

• Soyez prudents lorsque vous manipulez les piles aﬁn d’éviter les courts-circuits

provoqués par des matériaux conducteurs.

• Rechargez la pile incluse avec cet appareil, selon les instructions et limites spéciﬁées dans

ce guide d’utilisation.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (s’applique uniquement aux téléphones numériques sans ﬁl) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une ﬁrme de recherche

indépendante, a mené une évaluation pluridisciplinaire des interférences entre les

téléphones sans ﬁl portatifs et les stimulateurs cardiaques implantés dans l’organisme.

Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins :

Avis aux détenteurs de stimulateurs cardiaques

• Ils doivent tenir le téléphone sans ﬁl à une distance d’au moins six pouces du stimulateur

cardiaque.

• Ils ne doivent PAS placer le téléphone sans ﬁl directement sur le stimulateur cardiaque,

tel que dans une poche de chemise, lorsque celui-ci est en marche.

• Ils doivent utiliser le téléphone sans ﬁl en l’appuyant sur l’oreille qui se trouve dans la

direction opposée au stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a pas identiﬁé de risque pour les détenteurs de

simulateurs cardiaques causés par les gens qui utilisent un téléphone sans ﬁl à proximité de

ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes caractéristiques qui constituent des avantages pour les

téléphones sans ﬁl afﬁchent également des restrictions. Les appels téléphoniques

sont transmis entre le combiné sans ﬁl et le socle par le biais d’ondes radio ; il y a donc

la possibilité que vos conversations téléphoniques sans ﬁl soient interceptées par des

équipements de réception radio se trouvant dans la portée du combiné sans ﬁl. Pour cette

raison, vous ne devez pas percevoir les communications téléphoniques sans ﬁl comme étant

aussi conﬁdentielles que celles des téléphones à cordons.

Alimentation électrique : Le socle de ce téléphone sans ﬁl doit être branché à une prise

électrique fonctionnelle. La prise électrique ne doit pas être contrôlée par un interrupteur

mural. Les appels ne pourront pas être effectués du combiné sans ﬁl si le socle est débranché

ou mis hors tension ou si le courant est coupé.

Possibilité d’interférences aux téléviseurs : Certains téléphones sans ﬁl fonctionnent sur

des fréquences pouvant causer des interférences aux téléviseurs et aux magnétoscopes.

Pour réduire ou prévenir de telles interférences, ne placez pas le socle du téléphone

sans ﬁl près ou sur un téléviseur ou magnétoscope. S’il y a présence de parasites, il est

conseillé d’éloigner le téléphone sans ﬁl du téléviseur ou du magnétoscope aﬁn de réduire

possiblement les interférences.

Piles rechargeables : Manipulez les piles avec soin aﬁn de ne pas les court-circuiter avec

des bagues, bracelets ou clés. Les piles ou le conducteur peut surchauffer et causer des

blessures. Respectez la polarité adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure métallique de nickel : Jetez ces blocs-piles de

manière écologique et sécuritaire. Ne les incinérez pas et ne les percez pas. Tel que les autres

piles de ce type, elles pourraient dégager une matière toxique qui peut causer

des blessures corporelles si elles sont brûlées ou percées.

The RBRC® seal

The RBRC seal on the nickel-metal hydride battery indicates that VTech

Communications, Inc. is voluntarily participating in an industry program to

collect and recycle these batteries at the end of their useful lives, when taken

out of service within the United States and Canada.

The RBRC program provides a convenient alternative to placing used nickel-

metal hydride batteries into the trash or municipal waste, which may be illegal

in your area.

VTech’s participation in RBRC makes it easy for you to drop off the spent battery at local retailers

participating in the RBRC program or at authorized VTech product service centers. Please call

1 (800) 8 BATTERY® for information on Ni-MH battery recycling and disposal bans/restrictions

in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements for

a Class B digital device under Part 15 of the Federal Communications Commission (FCC)

rules. These requirements are intended to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by the party

responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Privacy of communications may not be ensured when using this telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio frequency

energy that can be safely absorbed by a user or bystander according to the intended usage

of the product. This product has been tested and found to comply with the FCC criteria. The

handset may be safely held against the ear of the user. The telephone base shall be installed

and used such that parts of the user’s body other than the hands are maintained at a distance

of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements

adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the

back or bottom of this equipment contains, among other things, a product identiﬁer in the

format US:AAAEQ##TXXXX. This identiﬁer must be provided to your telephone service

provider upon request.

The plug and jack used to connect this equipment to premises wiring and the telephone

network must comply with applicable Part 68 rules and technical requirements adopted

by ACTA. A compliant telephone cord and modular plug is provided with this product. It is

designed to be connected to a compatible modular jack that is also compliant. An RJ11 jack

should normally be used for connecting to a single line and an RJ14 jack for two lines. See

the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you may

connect to your telephone line and still have them ring when you are called. The REN for this

product is encoded as the 6th and 7th characters following the US: in the product identiﬁer

(e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be ﬁve

(5.0) or less. For more information, please contact your telephone service provider.

This equipment must not be used with Party Lines. If you have specially wired alarm dialing

equipment connected to your telephone line, ensure the connection of this equipment

does not disable your alarm equipment. If you have questions about what will disable alarm

equipment, consult your telephone service provider or a qualiﬁed installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until the

problem has been corrected. Replacement to this telephone equipment can only be made

by the manufacturer or its authorized agents. For replacement procedures, follow the

instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service provider

may temporarily discontinue your telephone service. The telephone service provider is

required to notify you before interrupting service. If advance notice is not practical, you will

be notiﬁed as soon as possible. You will be given the opportunity to correct the problem

and the telephone service provider is required to inform you of your right to ﬁle a complaint

with the FCC. Your telephone service provider may make changes in its facilities, equipment,

operation, or procedures that could affect the proper functioning of this product. The

telephone service provider is required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid compatible.

If this product has memory dialing locations, you may choose to store emergency telephone

numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test emergency

numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,

Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to

the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired

operation of the device.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the Industry

Canada technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN indicates

the maximum number of devices allowed to be connected to a telephone interface. The

termination of an interface may consist of any combination of devices subject only to the

requirement that the sum of the RENs of all the devices not exceed ﬁve.

This product meets the applicable Innovation, Science and Economic Development Canada

technical speciﬁcations.

California Energy Commission battery

charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the box.

These instructions are intended for California Energy Commission (CEC) compliance testing only.

When the CEC battery charging testing mode is activated, all telephone functions, except battery

charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all handsets

are plugged with charged batteries before proceeding.

2. While you press and hold /FIND HANDSET, plug the telephone base power adapter back

to the power outlet.

3. After about 30 seconds, when the IN USE light starts ﬂashing, release /FIND HANDSET and

then press it again within 2 seconds. When the phone successfully enters the CEC battery

charging testing mode, all handsets display To register HS and See manual alternatively.

When the phone fails to enter this mode, repeat Step 1 through Step 3 above.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it back in.

Then the telephone base is powered up as normal.

2. Press and hold /FIND HANDSET at the telephone base for about four seconds until the

IN USE light turns on.

3. Then press # on the handset. It displays Registering...

The handset show Registered and you hear a beep when the registration process completes.

The registration process takes about 60 seconds to complete.

Limited Warranty

What does this limited warranty cover?

The manufacturer of this VTech product, VTech Communications, Inc. (“VTech”), warrants

to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all

accessories provided by VTech in sales package (“Product”) are free from material defects in

material and workmanship, pursuant to the following terms and conditions, when installed

and used normally and in accordance with operating instructions. This limited warranty

extends only to the Consumer for Products purchased and used in the United States of

America and Canada.

What will VTech Communications do if the Product is not free from material defects in

materials and workmanship during the limited warranty period (“Materially Defective

Product”)?

During the limited warranty period, VTech’s authorized service representative will replace

at VTech’s option, without charge, a Materially Defective Product. If we choose to replace

the Product, we may replace it with a new or refurbished Product of the same or similar

design. VTech will return replacement products to you in working condition. VTech will retain

defective parts, modules, or equipment. Replacement of the Product, at VTech’s option, is

your exclusive remedy. You should expect the replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the product extends for ONE (1) YEAR from date of purchase

(90 days on products purchased as Refurbished*). This limited warranty also applies to

replacement Products for a period of either (a) 90 days from the date the replacement

Product is shipped to you or (b) the time remaining on the original one-year limited warranty

(90-day limited warranty on products that are purchased as Refurbished*), whichever is

longer.

*Refurbished products purchased from our online store carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical

damage, improper installation, abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration or modiﬁcation by anyone

other than an authorized service representative of VTech; or

3. Product to the extent that the problem experienced is caused by signal conditions,

network reliability or cable or antenna systems; or

4. Product to the extent that the problem is caused by use with non-VTech electrical

accessories; or

5. Product whose warranty/quality stickers, Product serial number plates or electronic

serial numbers have been removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair from outside the United States,

or used for commercial or institutional purposes (including but not limited to Products

used for rental purposes); or

7. Product returned without valid proof of purchase (see 2 below); or

8. Charges for installation or set up, adjustment of customer controls, and installation or

repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of America, please visit our website at www.

vtechphones.com or call 1 (800) 595-9511 for instructions regarding where to return the

Product. In Canada, go to phones.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s

controls and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit

and transportation and are responsible for delivery or handling charges incurred in the

transport of Product(s) to the service location. VTech will return replaced product under this

limited warranty to you, transportation, delivery or handling charges prepaid. VTech assumes

no risk for damage or loss of the Product in transit.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech

service location along with a description of the malfunction or difﬁculty;

2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased

(Product model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes

all other written or oral communications related to this product. VTech provides no other

warranties for this product. The warranty exclusively describes all of VTech’s responsibilities

regarding the product.

There are no other expressed warranties. No one is authorized to make modiﬁcations to this

warranty and you should not rely on any such modiﬁcation.

State Law Rights: This warranty gives you speciﬁc legal rights, and you may also have other

rights which vary from state to state.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and

merchantability (an unwritten warranty that the product is ﬁt for ordinary use) are limited to

one year from date of purchase. Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar

damages (including, but not limited to lost proﬁts or revenue, inability to use the product, or

other associated equipment, the cost of substitute equipment, and claims by third parties)

resulting from the use of this product. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above limitation or exclusion may not apply to

you.

Please retain your original sales receipt as proof of purchase

Disclaimer and Limitation of

Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or

loss resulting from the use of this user’s manual. VTech Communications, Inc. and its suppliers

assume no responsibility for any loss or claims by third parties that may arise through the use

of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

Need help?

Caller ID

If you subscribe to caller ID service, information about each

caller appears after the ﬁrst or second ring.

The caller ID log stores up to 30 entries. Each entry has up

to 24 digits for the phone number and 15 characters for the

name.

Review caller ID log entries

Press .

Scroll to browse the

entries.

Dial a caller ID log entry

Press SELECT.

Edit the name

if needed, then

press SELECT.

Edit name

Save a caller ID log entry to the directory

Delete a caller ID log entry

When your desired

caller ID entry

displays on the

handset screen

When your desired

caller ID entry

displays on the

handset screen

When your desired

caller ID entry

displays on the

handset screen

Press

Press DELETE to delete.

Caller ID

Press SELECT.

12Edit the phone

number if

needed.

HANDSET

10:15p

12/25

NEW

Mike Smith

595-9511

09:05.p

12/25

NEW

Mike Smith

595-9511

09:05.p

12/25

NEW

Mike Smith

595-9511

09:05.p

12/25

NEW

Mike Smith

595-9511

09:05.p

12/25

NEW

Edit number

595-9511_

Edit number

800-595-9511_

VTech CS6214-21 Guide de démarrage rapide

Marque: VTech

Modèle: CS6214-21

Taper: Guide de démarrage rapide

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: VTech CS6214-21 Quick start guide

VTech CS6214-21 Guide de démarrage rapide

Ce manuel convient également à

VTech CS6214-21 Guide de démarrage rapide

dans d''autres langues

Documents connexes