Asus B760M-AYW WIFI Manuel utilisateur

Marque: Asus

Modèle: B760M-AYW WIFI

Catégorie: Cartes mères

Taper: Manuel utilisateur

Motherboard

B760M-AYW

WIFI

E22921

First Edition

November 2023

No part of this manual, including the products and software described in it, may be reproduced,

transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by

any means, except documentation kept by the purchaser for backup purposes, without the express

written permission of ASUSTeK COMPUTER INC. (“ASUS”).

Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless

such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the

product is defaced or missing.

ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS

DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,

LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),

EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM

ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.

SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR

INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,

AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO

RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN

THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.

Products and corporate names appearing in this manual may or may not be registered trademarks or

copyrights of their respective companies, and are used only for identification or explanation and to the

owners’ benefit, without intent to infringe.

iii

Contents

Safety information ...................................................................................................... iv

About this guide .......................................................................................................... v

Package contents ...................................................................................................... vii

B760M-AYW WIFI specifications summary ........................................................... viii

Chapter 1: Product Introduction

1.1 Before you proceed ................................................................................... 1-1

1.2 Motherboard layout....................................................................................1-2

1.3 CPU installation..........................................................................................1-8

1.4 DIMM installation......................................................................................1-10

1.5 Wi-Fi moving antenna installation .......................................................... 1-12

Chapter 2: BIOS and RAID Support

2.1 Knowing UEFI BIOS ................................................................................... 2-1

2.2 ASUS EZ Flash 3 ........................................................................................ 2-2

2.3 ASUS CrashFree BIOS 3............................................................................2-3

2.4 RAID configurations .................................................................................. 2-4

Appendix

General Notices ....................................................................................................... A-1

Notices for Wi-Fi model .......................................................................................... A-4

Warranty ................................................................................................................... A-9

ASUS contact information .................................................................................... A-11

Service and Support ............................................................................................. A-11

Product Register ................................................................................................... A-11

Safety information

Electrical safety

• To prevent electrical shock hazard, disconnect the power cable from the electrical

outlet before relocating the system.

• When adding or removing devices to or from the system, ensure that the power cables

for the devices are unplugged before the signal cables are connected. If possible,

disconnect all power cables from the existing system before you add a device.

• Before connecting or removing signal cables from the motherboard, ensure that all

power cables are unplugged.

• Seek professional assistance before using an adapter or extension cord. These

devices could interrupt the grounding circuit.

• Ensure that your power supply is set to the correct voltage in your area. If you are not

sure about the voltage of the electrical outlet you are using, contact your local power

company.

• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service

technician or your retailer.

Operation safety

• Before installing the motherboard and adding devices on it, carefully read all the

manuals that came with the package.

• Before using the product, ensure all cables are correctly connected and the power

cables are not damaged. If you detect any damage, contact your dealer immediately.

• To avoid short circuits, keep paper clips, screws, and staples away from connectors,

slots, sockets and circuitry.

• Avoid dust, humidity, and temperature extremes. Do not place the product in any area

where it may become wet.

• Place the product on a stable surface.

• If you encounter technical problems with the product, contact a qualified service

technician or your retailer.

• Your motherboard should only be used in environments with ambient temperatures

between 10°C and 35°C.

Button/Coin Batteries Safety Information

WARNING

KEEP OUT OF REACH OF CHILDREN

Swallowing can lead to chemical burns,

perforation of soft tissue, and death. Severe

burns can occur within 2 hours of ingestion.

Seek medical attention immediately.

About this guide

This user guide contains the information you need when installing and configuring the

motherboard.

How this guide is organized

This guide contains the following parts:

• Chapter 1: Product Introduction

This chapter describes the features of the motherboard and includes descriptions for

each part of the motherboard.

• Chapter 2: BIOS and RAID Support

This chapter tells how to boot into the BIOS, upgrade BIOS using the EZ Flash Utility

and support on RAID.

Where to find more information

Refer to the following sources for additional information and for product and software

updates.

1. ASUS website

The ASUS website (www.asus.com) provides updated information on ASUS hardware

and software products.

2. Optional documentation

Your product package may include optional documentation, such as warranty flyers,

that may have been added by your dealer. These documents are not part of the

standard package.

3. MyASUS

MyASUS offers a variety of support features such as helping to troubleshoot issues,

optimizing product performance, integrating ASUS software, and recovery drive

creation. Please visit https://www.asus.com/support for installation guide and FAQ.

MyASUS is only available on selected models, please check your motherboard’s

specifications summary to see if your motherboard supports MyASUS.

6. RAID Configuration Guide

Please visit https://www.asus.com/support for more information on the RAID

Configuration Guide.

4. Motherboard Installation Guide

Please visit https://www.asus.com/support for more information on the Motherboard

Installation Guide.

5. Driver and Utilities FAQ

Please visit https://www.asus.com/support for more information on downloading and

installing drivers and utilities for your motherboard.

vii

Conventions used in this guide

To ensure that you perform certain tasks properly, take note of the following symbols used

throughout this user guide.

CAUTION: Information to prevent damage to the components and injuries to

yourself when trying to complete a task.

IMPORTANT: Instructions that you MUST follow to complete a task.

NOTE: Tips and additional information to help you complete a task.

Package contents

Check your motherboard package for the following items.

Motherboard 1 x B760M-AYW WIFI motherboard

Cables 2 x SATA 6Gb/s cables

Miscellaneous

1 x ASUS Wi-Fi moving antennas

1 x I/O Shield

1 x M.2 Rubber package

1 x Screw package for M.2 SSD

Documentation 1 x Quick start guide

• If any of the above items is damaged or missing, contact your retailer.

• Items not listed in the Package contents list above are purchased separately and do

not come bundled with your motherboard package.

viii

B760M-AYW WIFI specifications summary

CPU

Intel® Socket LGA1700 for Intel® Core™14th & 13th Gen Processors, Intel®

Core™ 12th Gen, Pentium® Gold and Celeron® Processors*

Supports Intel® Turbo Boost Technology 2.0 and Intel® Turbo Boost Max

Technology 3.0**

* Refer to www.asus.com for CPU support list.

** Intel® Turbo Boost Max Technology 3.0 support depends on the CPU types.

Chipset Intel® B760 Chipset

Memory

2 x DIMM slots, Max. 96GB, DDR5 Non-ECC, Un-buffered Memory*

Dual Channel Memory Architecture

Supports Intel® Extreme Memory Profile (XMP) memory module

* Supported memory types, data rate (speed), and number of DRAM modules vary

depending on the CPU and memory configuration, for more information please

refer to CPU/Memory Support list under the Support tab of product information

site or visit https://www.asus.com/support/.

* Non-ECC, un-buffered DDR5 memory supports On-Die ECC function.

Graphics

1 x HDMI™ port**

* Graphics specifications may vary between CPU types. Please refer to

www.intel.com for any updates.

** Supports 4K@60Hz as specified in HDMI 2.1.

Expansion Slots

Intel® Core™ Processors (14th & 13th & 12th Gen)

- 1 x PCIe 4.0 x16 slot

Intel® B760 Chipset

- 2 x PCIe 4.0 x1 slots

* To ensure compatibility of the device installed, please refer to

https://www.asus.com/support/ for the list of supported peripherals.

Storage

Total supports 2 x M.2 slots and 4 x SATA 6Gb/s ports*

Intel® Core™ Processors (14th & 13th & 12th Gen)

- M.2_1 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 mode)

Intel® B760 Chipset

- M.2_2 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 mode)

- 4 x SATA 6Gb/s ports

* Intel® Rapid Storage Technology supports SATA RAID 0/1/5/10.

Ethernet 1 x Realtek 2.5Gb Ethernet

ASUS LANGuard

Wireless &

Bluetooth®

Wi-Fi 6 (802.11 a/b/g/n/ac/ax)

Supports 2.4/5GHz frequency band

Bluetooth® v5.3*

* The Bluetooth version may vary, please refer to the Wi-Fi module

manufacturer’s website for the latest specifications.

USB

Rear USB (Total 6 ports)

4 x USB 3.2 Gen 1 ports (4 x Type-A)

2 x USB 2.0 ports (2 x Type-A)

Front USB (Total 4 ports)

1 x USB 3.2 Gen 1 header supports 2 additional USB 3.2 Gen 1 ports

1 x USB 2.0 header supports 2 additional USB 2.0 ports

(continued on the next page)

B760M-AYW WIFI specifications summary

Audio

Realtek 7.1 Surround Sound High Definition Audio CODEC*

- Supports: Jack-detection, Multi-streaming, Front Panel Jack-retasking

- Supports up to 24-Bit/192 kHz playback

Audio Features

- Audio Shielding

- Premium audio capacitors

- Dedicated audio PCB layers

* A chassis with an HD audio module in the front panel is required to support 7.1

Surround Sound audio output.

Back Panel I/O Ports

4 x USB 3.2 Gen 1 ports (4 x Type-A)

2 x USB 2.0 ports (2 x Type-A)

1 x HDMI™ port

1 x Wi-Fi Module

1 x Realtek 2.5Gb Ethernet port

3 x Audio jacks

Internal I/O

connectors

Fan and Cooling Related

1 x 4-pin CPU Fan header

2 x 4-pin Chassis Fan headers

Power Related

1 x 24-pin Main Power connector

1 x 8-pin +12V Power connector

Storage Related

2 x M.2 slots (Key M)

4 x SATA 6Gb/s ports

USB

1 x USB 3.2 Gen 1 header supports 2 additional USB 3.2 Gen 1 ports

1 x USB 2.0 header supports 2 additional USB 2.0 ports

Miscellaneous

3 x Addressable Gen 2 headers

1 x Clear CMOS header

1 x COM Port header

1 x Front Panel Audio header (AAFP)

1 x S/PDIF Out header

1 x Speaker header

1 x SPI TPM header (14-1pin)

1 x 10-1 pin System Panel header

(continued on the next page)

B760M-AYW WIFI specifications summary

Special Features

ASUS 5X PROTECTION III

- DIGI+ VRM

- LANGuard

- Overvoltage Protection

- SafeSlot Core +

- Stainless-Steel Back I/O

ASUS Q-Design

- M.2 Q-Latch

- Q-DIMM

- Q-LED Core

- Q-Slot

ASUS Thermal Solution

- M.2 heatsink

- VRM heatsink design

ASUS EZ DIY

- ProCool

Aura Sync

- Addressable Gen 2 headers

Software Features

ASUS Exclusive Software

Armoury Crate

- Aura Sync

- Fan Xpert 2+

- Power Saving

- Two-Way AI Noise Cancelation

AI Suite 3

- DIGI+ VRM

- PC Cleaner

ASUS CPU-Z

MyASUS

Norton 360 Deluxe (60 Days Free Trial)

WinRAR

UEFI BIOS

ASUS EZ DIY

- ASUS CrashFree BIOS 3

- ASUS EZ Flash 3

- ASUS UEFI BIOS EZ Mode

BIOS 128 Mb Flash ROM, UEFI AMI BIOS

BIOS CAP Filename B760M-AYW WIFI: B760MAW.CAP

Manageability WOL by PME, PXE

Operating System Windows® 11

Windows® 10 64-bit

Form Factor mATX Form Factor

9.6 inch x 8.3 inch (24.4 cm x 21.1 cm)

Specifications are subject to change without notice. Please refer to the ASUS website for

the latest specifications.

1-1Motherboard User Manual

Product Introduction

Chapter 1: Product Introduction

• Unplug the power cord from the wall socket before touching any component.

• Before handling components, use a grounded wrist strap or touch a safely grounded

object or a metal object, such as the power supply case, to avoid damaging them due

to static electricity.

• Hold components by the edges to avoid touching the ICs on them.

• Whenever you uninstall any component, place it on a grounded antistatic pad or in the

bag that came with the component.

• Before you install or remove any component, ensure that the power supply is switched

off or the power cord is detached from the power supply. Failure to do so may cause

severe damage to the motherboard, peripherals, or components.

• The pin definitions in this chapter are for reference only. The pin names depend on the

location of the header/jumper/connector.

• The illustrations for this chapter are for reference only. The WiFi module is only

available on selected models.

1.1 Before you proceed

Take note of the following precautions before you install motherboard components or change

any motherboard settings.

1-2 Chapter 1: Product Introduction

1.2 Motherboard layout

DDR5 DIMM_A (64bit, 288-pin module)

DDR5 DIMM_B (64bit, 288-pin module)

CPU_FAN

CHA_FAN1

ADD_GEN 2_1

ADD_GEN 2_2

DIGI+

VRM

ADD_GEN 2_3

CHA_FAN2

F_PANEL

SPDIF_OUT

COM_DEBUG

SATA6G_1

CLRTC

TPM SATA6G_2 SATA6G_3

SATA6G_4

128Mb

BIOS

ATX_12V

ATX_PWR

U32G1_12

BATTERY

HDMI

USB_56

LAN_U32G1_910

U32G1_34

Audio

Codec

Super

I/O

PCIEX1(G4)_1

PCIEX1(G4)_2

2280 2260 2242

LGA1700

PCIEX16(G4)

USB_811

AAFP

24.4cm(9.6in)

COM

AUDIO

M.2_2(SOCKET3)

M.2_1(SOCKET3)

PCIE SATA

4.0 X4 X

PCIE SATA

4.0 X4 X

SPEAKER

Intel®

B760

Ethernet

21.1cm(8.3in)

2242 2260 2280

M.2(WIFI)

141213

5 1 10 10

6 4

171591110 4 16 7

1.2.1 Layout contents

1. CPU socket

The motherboard comes with a LGA1700 socket designed for Intel® Core™ 14th & 13th Gen

Processors, Intel® Core™ 12th Gen, Pentium® Gold and Celeron® Processors.

For more details, refer to CPU installation.

2. DIMM slots

The motherboard comes with Dual Inline Memory Modules (DIMM) slots designed for DDR5

(Double Data Rate 5) memory modules.

For more details, refer to DIMM installation.

1-3Motherboard User Manual

3. Expansion slots

This motherboard supports one PCIe x16 graphics card and two PCIe x1 network cards,

SCSI cards and other cards that comply with the PCI Express specification.

4. Fan headers

The Fan headers allow you to connect fans to cool the system.

5. Power connectors

These Power connectors allow you to connect your motherboard to a power supply. The

power supply plugs are designed to fit in only one orientation. Find the proper orientation and

push down firmly until the power supply plugs are fully inserted.

Ensure to connect the 8-pin power plug.

We recommend that you use a PSU with a higher power output when configuring a system

with more power-consuming devices. The system may become unstable or may not boot

up if the power is inadequate.

6. M.2 slots (Key M)

The M.2 slots allow you to install M.2 devices such as M.2 SSD modules.

• Intel® Core™ Processors (14th & 13th & 12th Gen)

M.2_1 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 mode)

• Intel® B760 Chipset

M.2_2 slot (Key M), type 2242/2260/2280 (supports PCIe 4.0 x4 mode)

7. SATA 6Gb/s ports

The SATA 6Gb/s ports allow you to connect SATA devices such as optical disc drives and

hard disk drives via SATA cables.

8. USB 3.2 Gen 1 header

The USB 3.2 Gen 1 header allows you to connect a USB 3.2

Gen 1 module for additional USB 3.2 Gen 1 ports. The USB 3.2

Gen 1 header provides data transfer speeds of up to 5 Gb/s.

9. USB 2.0 header

The USB 2.0 header allows you to connect a USB module for

additional USB 2.0 ports. The USB 2.0 header provides data

transfer speeds of up to 480 Mb/s.

DO NOT connect a 1394 cable to the USB connectors. Doing

so will damage the motherboard!

GND

FAN PWR

FAN IN

FAN PWM

1-4 Chapter 1: Product Introduction

10. Addressable Gen 2 headers

The Addressable Gen2 headers allow you to connect individually

addressable RGB WS2812B LED strips or WS2812B based LED strips.

Before you install or remove any component, ensure that the power

supply is switched off or the power cord is detached from the power

supply. Failure to do so may cause severe damage to the motherboard,

peripherals, or components.

• The Addressable Gen2 header supports WS2812B addressable RGB LED strips (5V/

Data/Ground), with a maximum power rating of 3A (5V), and the addressable headers

on this board can handle a combined maximum of 500 LEDs.

• Actual lighting and color will vary with LED strip.

• If your LED strip does not light up, check if the addressable RGB LED strip is

connected in the correct orientation, and the 5V connector is aligned with the 5V

header on the motherboard.

• The addressable RGB LED strip will only light up when the system is powered on.

11. Clear CMOS header

The Clear CMOS header allows you to clear the Real Time Clock (RTC) RAM

in the CMOS, which contains the date, time, system passwords, and system

setup parameters.

To erase the RTC RAM:

1. Turn OFF the computer and unplug the power cord.

2. Short-circuit pin 1-2 with a metal object or jumper cap for about 5-10 seconds.

3. Plug the power cord and turn ON the computer.

4. Hold down the <Del> key during the boot process and enter BIOS setup to re-

enter data.

DO NOT short-circuit the pins except when clearing the RTC RAM. Short-circuiting or

placing a jumper cap will cause system boot failure!

If the steps above do not help, remove the onboard button cell battery and short the two

pins again to clear the CMOS RTC RAM data. After clearing the CMOS, reinstall the button

cell battery.

12. COM Port header

The COM (Serial) Port header allows you to connect a COM port module.

Connect the COM port module cable to this header, then install the module

to a slot opening on the system chassis.

ADD_GEN 2

Ground

Data

+5V

PIN 1

CLRTC

PIN 1

RXD

DTR

DSR

CTS

COM

DCD

TXD

GND

RTS

1-5Motherboard User Manual

13. Front Panel Audio header

The Front Panel Audio header is for a chassis-mounted

front panel audio I/O module that supports HD Audio.

Connect one end of the front panel audio I/O module cable

to this header.

14. S/PDIF Out header

The S/PDIF Out header allows you to connect the Sony/Philips Digital

Interface (S/PDIF) Out module.

15. Speaker header

The Speaker header allows you to connect the chassis-mounted system

warning speaker. The speaker allows you to hear system beeps and warnings.

16. SPI TPM header

This header supports a Trusted Platform Module (TPM)

system with a Serial Peripheral Interface (SPI), allowing

you to securely store keys, digital certificates, passwords,

and data. A TPM system also helps enhance network

security, protects digital identities, and ensures platform

integrity.

17. System Panel header

The System Panel header supports several chassis-mounted functions.

• System Power LED header (+PWR_LED-)

The 2-pin header allows you to connect the System Power LED. The

System Power LED lights up when the system is connected to a power

source, or when you turn on the system power, and blinks when the

system is in sleep mode.

• Storage Device Activity LED header (+HDD_LED-)

The 2-pin header allows you to connect the Storage Device Activity

LED. The Storage Device Activity LED lights up or blinks when data

is read from or written to the storage device or storage device add-on

card.

• Power Button/Soft-off Button header (PWR_BTN)

The 2-pin header allows you to connect the system power button. Press the power

button to power up the system, or put the system into sleep or soft-off mode

(depending on the operating system settings).

• Reset button header (RESET)

The 2-pin header allows you to connect the chassis-mounted reset button. Press the

reset button to reboot the system.

AAFP

SPDIF_OUT

+5V

GND

Speaker Out

SPEAKER

PIN 1

TPM

PIN 1

VCCSPI

S_PLTRST#

F_SPI_PWR

F_SPI_CZS0#_R

T_SPI_MISO

F_SPI_HOLD#_R

S_SPI_TPM_IRQ#

S_SPI_TPM_CS2#

TPM_DETECT_L

GND

T_SPI_CLK

T_SPI_MOSI

PIN 1

PWR_BTN

PWR_LED+

PWR_LED-

PWR

GND

HDD_LED+

HDD_LED-

Ground

HWRST#

(NC)

F_PANEL

+PWR_LED-

+HDD_LED- RESET

1-6 Chapter 1: Product Introduction

1.2.2 Rear panel connectors

3 4 5 6

1 2

Rear panel connectors

1. Realtek 2.5Gb Ethernet port*

2. Audio jacks**

3. USB 2.0 ports 5, 6

4. HDMI™ port

5. USB 3.2 Gen 1 Type-A ports 3, 4, 9, 10

6. Wi-Fi module

* and **: Refer to the tables below for LAN port LEDs, and audio port definitions.

Speed LED

Status Description

OFF No link

GREEN 2.5 Gbps connection

ORANGE 1 Gbps / 100 Mbps /

10 Mbps connection

Activity Link LED

Status Description

OFF No link

GREEN Linked

BLINKING Data activity

ACT/LINK

LED

SPEED

LED

LAN port

* Realtek 2.5Gb Ethernet port LED indications

We strongly recommend that you connect your devices to ports with matching data transfer

rate. For example connecting your USB 3.2 Gen 1 devices to USB 3.2 Gen 1 ports for

faster and better performance for your devices.

1-7Motherboard User Manual

** Audio 2, 4, 5.1 or 7.1-channel configuration

Port 2-channel 4-channel 5.1-channel 7.1-channel

Rear panel

LINE IN - Rear Speaker

Out

Rear Speaker

Out

Rear Speaker

Out

LINE OUT Front Speaker

Out

Front Speaker

Out

Front Speaker

Out

Front Speaker

Out

MIC IN - Center/

Subwoofer

Center/

Subwoofer

Front panel

HEADPHONE

(Lime) - - - Side Speaker Out

MIC IN

(Pink) - - - -

1-8 Chapter 1: Product Introduction

1.3 CPU installation

• Ensure that you install the correct CPU designed for LGA1700 socket only. DO NOT

install a CPU designed for LGA1155, LGA1156, LGA1151, and LGA1200 sockets on

the LGA1700 socket.

• The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to

prevent bending the connectors on the socket and damaging the CPU.

• Ensure that all power cables are unplugged before installing the CPU.

• Upon purchase of the motherboard, ensure that the PnP cap is on the socket and

the socket contacts are not bent. Contact your retailer immediately if the PnP cap

is missing, or if you see any damage to the PnP cap/socket contacts/motherboard

components. ASUS will shoulder the cost of repair only if the damage is shipment/

transit-related.

Install a heatsink or AIO cooler after installing the CPU. Please refer to the Motherboard

Installation Guide on the ASUS support site, or to the user manual of the heatsink/AIO

cooler for steps on installing the heatsink/AIO cooler.

Take caution when lifting the load lever,

ensure to hold onto the load lever when

releasing the load lever. Letting go of the

load lever immediately after releasing it may

cause the load lever to spring back and cause

damage to your motherboard

1-9Motherboard User Manual

1-10 Chapter 1: Product Introduction

1.4 DIMM installation

A DDR5 memory module is notched differently from a DDR, DDR2, DDR3, or DDR4

module. DO NOT install a DDR, DDR2, DDR3, or DDR4 memory module to the DDR5

slot.

Recommended memory configurations

DIMM_B

DIMM_A

DIMM_B

DIMM_A

You may install Non-ECC DDR5 DIMMs into the DIMM sockets.

• You may install varying memory sizes in the DIMM channels. The system maps the

total size of the lower-sized channel for the dual-channel configuration. Any excess

memory from the higher-sized channel is then mapped for single-channel operation.

• The default memory operation frequency is dependent on its Serial Presence Detect

(SPD), which is the standard way of accessing information from a memory module.

Under the default state, some memory modules for overclocking may operate at a

lower frequency than the vendor-marked value.

• For system stability, use a more efficient memory cooling system to support a full

memory load or overclocking condition.

• Always install the DIMMS with the same CAS Latency. For an optimum compatibility,

we recommend that you install memory modules of the same version or data code

(D/C) from the same vendor. Check with the vendor to get the correct memory

modules.

• Visit the ASUS website for the latest QVL.

The figure illustrates the location of the DDR5 DIMM sockets

DIMM_A

DIMM_B

La page est en cours de chargement...

Asus B760M-AYW WIFI Manuel utilisateur

Marque: Asus

Modèle: B760M-AYW WIFI

Catégorie: Cartes mères

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

italiano: Asus B760M-AYW WIFI Manuale utente
English: Asus B760M-AYW WIFI User manual
română: Asus B760M-AYW WIFI Manual de utilizare

Asus B760M-AYW WIFI Manuel utilisateur

Asus B760M-AYW WIFI Manuel utilisateur

dans d''autres langues

Documents connexes