Maytag MDG28PNCGW Installation Instructions Manual

INSTALLATION

INSTRUCTIONS

CommerCial He Dryer

Gas

INSTRUCTIONS

D’INSTALLATION

sèCHe-linGe He CommerCial

À Gaz

INSTRUCCIONES

DE INSTALACIÓN

seCaDora He ComerCial

a Gas

ISTRUZIONI

D’INSTALLAZIONE

asCiuGatriCe He CommerCiale

a Gas

www.maytagcommerciallaundry.comW10590742A

MDG28PN

MDG28PD

2

TABLE OF CONTENTS

Page

Dryer Safety ............................................................................ 3

Dryer Disposal ........................................................................ 6

Tools & Parts .......................................................................... 7

Dimensions/Clearances ........................................................ 8

Installation Requirements ..................................................... 9

Venting Requirements ......................................................... 12

Gas Supply Requirements .................................................. 14

Installing Leveling Legs, Payment Device, and Coin Box 15

Leveling ................................................................................ 16

Complete Installation .......................................................... 17

Reversing Door Swing (optional) ........................................ 18

Maintenance Instructions ................................................... 20

If You Need Assistance ....................................................... 20

Technical Specications – Gas Dryer ................................ 21

Electronic Control Setup Instructions ............................... 22

Warranty ............................................................................... 27

TABLE DES MATIÈRES

Page

Sécurité du sèche-linge ........................................................ 28

Élimination du sèche-linge ................................................... 31

Outils et pièces ..................................................................... 32

Dimensions/Distances de dégagement ............................. 33

Exigences d’installation ....................................................... 34

Exigences concernant l’évacuation .................................... 37

Spécications de l’alimentation en gaz ............................. 40

Installation des pieds de nivellement, du dispositif

de paiement et de la caisse à monnaie ............................... 41

Nivellement ........................................................................... 42

Achever l’installation ............................................................ 43

Inversion du sens d’ouverture de la porte (facultatif) ........ 44

Instructions d’entretien ........................................................ 46

Si vous avez besoin d’assistance ....................................... 46

Fiche technique – sèche-linge à gaz .................................. 47

Instructions de réglage du tableau

de commande électronique ................................................. 48

Garantie ................................................................................. 54

ÍNDICE

Página

Seguridad de la secadora ..................................................... 55

Eliminación de la secadora .................................................. 58

Herramientas y piezas .......................................................... 59

Dimensiones y espacios libres ............................................ 60

Requisitos de instalación ..................................................... 61

Requisitos de ventilación ..................................................... 64

Requisitos del suministro de gas ........................................ 67

Instalación de las patas, del dispositivo del pago

y la caja de monedas ............................................................ 68

Nivelación .............................................................................. 69

Complete la instalación ....................................................... 70

Cómo invertir el cierre de la puerta (opcional) .................. 71

Instrucciones de mantenimiento ......................................... 73

Si necesita ayuda ................................................................. 73

Especicaciones técnicas – secadora a gas ..................... 74

Instrucciones de programación

del control electrónico ......................................................... 75

Garantía ................................................................................. 81

INDICE

Pagina

Sicurezza dell’asciugatrice .................................................. 82

Eliminazione dell’asciugatrice ............................................. 85

Attrezzi e componenti ......................................................... 86

Dimensioni/spazi ................................................................. 87

Requisiti dell’installazione .................................................. 88

Requisiti di scarico .............................................................. 91

Requisiti di alimentazione del gas ..................................... 93

Installazione dei piedini di regolazione, dello

dispositivo di pagamento e del salvadanaio ..................... 94

Livellamento ......................................................................... 95

Completamento dell’installazione ..................................... 96

Inversione della rotazione di apertura (facoltativo) .......... 97

Istruzioni di manutenzione .................................................. 99

Se avete bisogno dell’assistenza ....................................... 99

Dati tecnici – asciugatrice a gas ...................................... 100

Congurazione dei controlli elettronici ........................... 101

Garanzia ............................................................................. 107

3

DRYER SAFETY

The dryer shall be disconnected from its power source during service and when replacing parts. If the removal of plug is

foreseen, it shall be clearly indicated that the removal of the plug has to be such that an operator can check from any of the

points to which they have access that the plug remains removed.

If this is not possible, due to the construction of the dryer or its installation, a disconnection with a locking system in the

isolated position shall be provided.

n It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer

smells gas. This information should be obtained from your gas supplier.

n Post the following warning in a prominent location.

FOR YOUR SAFETY

1. DO NOT USE OR STORE PETROL OR OTHER FLAMMABLE MATERIALS IN THIS APPLIANCE OR NEAR THIS APPLIANCE.

2. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

3. DO NOT MODIFY THIS APPLIANCE.

4

DRYER SAFETY

CAUTION –

RISK OF FIRE/FLAMMABLE MATERIALS

This is an additional safety alert symbol that alerts you to the risk of re.

5

DRYER SAFETY

n Do not install or store the dryer where it will be exposed

to the weather.

n Do not tamper with controls.

n Clean dryer lint screen before or after each load.

n Do not use this dryer without the lint screen in place.

n Do not repair or replace any part of the dryer or attempt

any servicing unless specically recommended in

this Use and Care Guide or in published user-repair

instructions that you understand and have the skills

to carry out.

n Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

n Do not use heat to dry articles containing foam rubber

or similarly textured rubber-like materials.

n The nal part of a tumble dryer cycle occurs without

heat (cool-down cycle) to ensure that the articles are left

at a temperature that ensures that the items will not be

damaged.

n WARNING: Never stop a tumble dryer before the end

of the drying cycle unless all items are quickly removed

and spread out so that the heat is dissipated. (Avoids risk

of spontaneous combustion).

n In case of electrical supply failure, remove the load

quickly and spread it out to avoid risk of spontaneous

combustion.

n Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint,

dust, and dirt.

n The fresh air ventilation openings into the room and into

the dryer must not be blocked or sealed.

n Emergency stop control: After installation, access to

mains plug or disconnection from mains supply via a

double-pole switch must be ensured at all times in order

to ensure immediate deactivation of the dryer in case of

emergency.

n The interior of the dryer and dryer exhaust vent should

be cleaned periodically by qualied service personnel.

n See “Electrical Requirements” section for earthing

instructions.

n The dryer shall be disconnected from its power source

during service and when replacing parts. If the removal

of the plug is foreseen, it shall be clearly indicated that it

be possible for the operator to conrm the removal of the

plug from any point of access.

If this is not possible due to the construction of the dryer

or its installation, a disconnection with a locking system

in the isolated position shall be provided.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of re, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

SAVE THESE INSTRUCTIONS

n Read all instructions before using the dryer.

n This dryer is intended only for drying clothes and textiles

that have been washed in water. Do not use for any other

purpose.

n WARNING: If you smell gas, do not use the dryer or any

electrical equipment nearby. Warn other people to clear

the area. Contact the dryer owner immediately.

n Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch re.

n If it is unavoidable that fabrics that contain vegetable or

cooking oil or that have been contaminated by hair care

products be placed in a tumble dryer, they should rst

be washed in hot water with extra detergent – this will

reduce, but not eliminate the hazard.

n Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with petrol,

dry-cleaning solvents, other ammable, or explosive

substances as they give off vapors that could ignite

or explode.

n Items that have been soiled with substances such

as acetone, alcohol, petrol, kerosene, spot removers,

turpentine, waxes, and wax removers should be washed

in hot water with extra detergent before being dried in

the dryer.

n Do not dry unwashed items in the dryer.

n Do not use this dryer if industrial chemicals have been

used for cleaning. The possible presence of residual

quantities of aggressive or decomposed chemicals in

the load may produce damage to the dryer and harmful

fumes.

n Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

n This dryer is not intended for use by persons (including

children) with reduced physical, sensory, or mental

capabilities, or lack of experience or knowledge,

unless they have been given supervision or instruction

concerning use of the dryer by a person responsible

for their safety.

n Before the dryer is removed from service or discarded,

remove the door to the dryer compartment.

n Do not reach into the dryer if the drum is moving.

n Opening the dryer door will stop the function of the dryer.

n When loading or re-loading the dryer, avoid touching hot

metal parts of the drum (burn risk).

n If drum rotation is blocked due to trapped textiles,

disconnect the dryer from the electrical supply before gently

removing the blockage.

n If the dryer is not heating, or appears to be defective or

damaged, do not use it. Contact the owner.

6

DRYER DISPOSAL

This appliance is marked according to the European directive 2012/19/EU on Waste Electrical and Electronic Equipment

(WEEE).

By ensuring this product is disposed of correctly, you will help avoid potential negative consequences for the environment

and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be

treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical

and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city ofce,

your household waste disposal service or the shop where you purchased the product.

MODEL NOMENCLATURE:

MDG – Maytag Dryer – Gas PN – Electronic Control – Non-Pay

## (e.g. 28) – Model Type Number PD – Electronic Control – Coin Drop Enabled

7

Tools Needed:

203 mm (8") 203 mm (8") or 254 mm (10") Flat-blade screwdriver Phillips screwdriver

or 254 mm (10") Adjustable wrench

Pipe wrench that opens to 25 mm (1")

Torx T20

®†

Security 25 mm (1") Hex-head 8 mm (5/16") Socket wrench Pliers

screwdriver or bit socket wrench (that open to 39 mm [1

9

/

16

"])

Level Utility knife 6 mm (1/4") Nut driver Locking pliers

Caulk gun and caulk Vent clamps Pipe-joint compound 686 mm (27") Wood block

(for installing new exhaust vent) suitable for gas type

Flashlight (optional) 25 mm (1") Ruler or measuring tape Putty knife

Open-end wrenches

TOOLS & PARTS

†® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

NOTE: The circuit diagram for this dryer is located inside the lower front panel, within the Tech Sheets.

Parts Supplied:

n Foot boots (4)

n Leveling legs (4)

n PN models: Card reader bezel, hardware

8

DIMENSIONS/CLEARANCES

Front View Side View Back View

Dimensions

Clearances

Recessed Front View

686 mm

(27")

965 mm

(38")

25 mm

(

1"

)

736 mm

(29")

921 mm

(36

1

/4")

25 mm

(

1"

)

695 mm

(27

1

/4")

203 mm

(8")

356 mm

(14")

25 mm

(1")

0 mm

(0")

381 mm

(15")

0 mm

(0")

159 mm

(6

1

/4")

715 mm

(28

1

/8")

89 mm

(3

1

/2")

358 mm

(

14"

)

32 mm

(

1

/4"

)

152 mm

(5

7

/8")

Closet Side View

9

Your dryer can be installed in a basement, laundry room,

or recessed area.

Companion appliance location requirements should also

be considered.

IMPORTANT: Do not install or store the dryer where it

will be exposed to the weather. Proper installation is your

responsibility.

You will need:

n A level oor with a maximum slope of 25 mm (1") under

entire dryer. Installing the dryer on soft oor surfaces,

such as carpets or surfaces with foam backing, is not

recommended.

n A sturdy and solid oor to support the dryer with a total

weight (load) of 204 kg (450 lbs).

Installation clearances

n The location must be large enough to allow the dryer door

to be fully opened.

n Additional spacing should be considered for ease of

installation and servicing. The door opens more than 180°.

n Additional clearances might be required for wall, door,

and oor moldings.

n Additional spacing of 25 mm (1") on all sides of the dryer

is recommended to reduce noise transfer.

n Companion appliance spacing should also be considered.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

n Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

NOTE: For installation in Australia and New Zealand,

install dryer in accordance with AS/NZS 5601.1 and local

governance codes.

n Make sure that lower edges of the cabinet, plus the back and

bottom sides of the dryer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See

“Recessed Area and Closet Installation Instructions” below

for minimum spacing requirements.

n Do not install on carpet.

Location

INSTALLATION REQUIREMENTS

Recessed Area and Closet Installation Instructions

This dryer may be installed in a recessed area or closet. The

dryer must not be installed behind a lockable door, a sliding door,

or a door with a hinge on the opposite side to that of the dryer

in such a way that a full opening of the dryer door is restricted.

For recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer or in

“Dimensions/Clearances.”

The installation spacing is in millimeters and is the minimum

allowable. Additional spacing should be considered for ease

of installation, servicing, and compliance with local codes

and ordinances.

If closet door is installed, the minimum unobstructed air

opening in the top and bottom is required. Louvered doors

with equivalent air openings are acceptable.

The dryer must be exhausted outdoors.

No other fuel-burning appliance may be installed in the same

closet as the dryer.

NOTE: For installation in Australia and New Zealand, refer

to AS/NZS 5601.1 for ventilation requirements.

NOTE: This dryer is not intended to be placed on top

of a washer.

10

INSTALLATION REQUIREMENTS

Electrical Requirements

EARTHING INSTRUCTIONS

SAVE THESE INSTRUCTIONS

IMPORTANT: Observe all governing codes and ordinances.

You will need an earthed electrical outlet located within

610 mm (2 feet) of either side of the dryer.

This dryer is supplied/tted with an electrical supply cord

and plug. It should be connected to electrical supply socket

at the voltage shown on the rating plate. The minimum supply

fuse capacity should be 5A. The dryer must be positioned so

that the plug is clearly visible and accessible. This plug also

provides the function of an emergency stop control for the user.

If the tted plug is not used, the electrical connection must be

carried out by a competent electrician in accordance with local

or national codes.

If the supply cord is damaged, it must be replaced with a

specially terminated cord by an authorized service agent

or a similarly competent person in order to avoid a hazard.

Do not use an adapter.

Do not use an extension cord.

NOTE: In accordance with the European EMC Directive

(2004/108/EC), the maximum electricity supply system

impedance to which the gas dryer should be connected

is declared to be 0.054 Ohm + j0.034 Ohm.

NOTE: Electrical safety standards: The manufacturer has

chosen compliance with IEC/EN.60335 standards as the most

appropriate for this product.

If codes permit and an additional earth bond wire is used, it is

recommended that a qualied electrician determine that the

earth bond path is adequate.

Using the universal cord included with this dryer:

The gas dryer is equipped with a universal cord with

interchangeable plugs.

1. To use the universal cord, select the plug end that ts your

electrical outlet, and plug it into the adapter on the supply

cord.

2. Secure the plug end in place on the cord by aligning the

2 cover halves over the cord adapter and clipping them

together.

11

INSTALLATION REQUIREMENTS

Gas Supply Requirements

IMPORTANT: Observe all governing codes and ordinances.

Gas Supply

Before installation, check that the local gas distribution

conditions, nature of gas and pressure, and the adjustment

of the appliance are compatible. Burner information will be

found on the model/serial rating plate in the door recess of the

dryer. If this information does not agree with the type of gas

available, see your dealer.

Natural Gas:

This dryer is factory adjusted for use with NATURAL GAS (G20),

and no further adjustment should be required at installation.

L.P. Gas:

This dryer is also certied for use with L.P. (propane or butane)

gases with appropriate conversion. No attempt shall be made

to convert the appliance from the gas specied on the model/

serial rating plate for use with a different gas without consulting

the serving gas supplier.

Conversion must be done by a competent service technician.

Gas conversion kit (European Country), part number

W10233219, is available for purchase from your dealer. Gas

conversion kit (Australia), part number W10315369, is available

for purchase from your dealer. Full instructions are supplied

with the kit.

Natural gas (France/Belgium):

This dryer is also certied for France/Belgium for use

with G20/G25 gases (20 mbar/25 mbar) with appropriate

conversion. No attempt should be made to convert this

appliance from the gas specied on the gas rating label

for use with a different gas without consulting the serving

gas supplier. Gas conversion must be done by a qualied gas

service technician. Conversion kit, part number (W10181947)

is available for purchase from your dealer. Full instructions are

supplied with the kit.

Supply line requirements:

Provide a rigid gas supply line to the dryer location. It should

be minimum 12.5 mm (1/2") ID. When acceptable to the gas

supplier and local codes, 10 mm (3/8") ID rigid supply line may

be used for lengths under 6.1 m (20'). Pipe-joint compounds

resistant to the action of L.P. gas must be used.

NOTE: For installation in Australia and New Zealand, refer

to AS/NZS 5601 for pipe sizing details.

Gas connection to the dryer itself should be made by means

of a exible gas hose suitable for the appliance and gas

category in accordance with national installation regulations.

If in doubt, contact the gas supplier. It should be minimum

10 mm (3/8") ID.

A means of restraint should be used between the dryer and the

wall to avoid straining of the rigid gas supply when the dryer

is moved. An appropriate length of chain and a wall hook is

recommended.

The dryer gas inlet connection is a 3/8" NPT thread.

An adapter is supplied for conversion to standard ISO.228-1

thread (3/8" BSP).

Check for leaks by using an approved noncorrosive

leak-detection solution. Bubbles will show a leak. Correct any

leak found. A pressure measurement tapping is provided on the

gas valve within the dryer, accessible after removal of the lower

front panel.

The dryer must be disconnected from the gas supply piping

system during any pressure testing of that system.

The expected pressures for the gas supply are listed in Inches

of Water Column in the table below:

Gas Supply Minimum Maximum

Natural Gas 5.2 10.5

LP Gas 8.0 13.0

12

VENTING REQUIREMENTS

WARNING: To reduce the risk of re, this dryer MUST BE

EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

■ Following these venting requirements will minimize ducting

air noise.

■ Exhaust air must not be discharged into a ue which is used

for exhausting fumes from other appliances burning gas or

other fuels, including open res (i.e. available airow into

the room should match airow out from the room).

■ Adequate ventilation must be provided to avoid the back

ow of gases into the room from appliances burning other

fuels, including open res.

■ Dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, attic, crawlspace, or a concealed

space of a building. Only rigid or exible metal vent shall

be used for exhausting.

■ Do not use an exhaust hood with a magnetic latch.

■ Only a 102 mm (4") heavy, metal exhaust vent and clamps

may be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in nal dryer location.

■ Remove excess to avoid sagging and kinking that may

result in reduced airow and poor performance.

■ Do not install in enclosed walls, ceilings, or oors.

■ The total length should not exceed 2.4 m (7

3

⁄

4

ft.).

■ An exhaust hood should cap the vent to keep rodents

and insects from entering the building.

102 mm

(

4"

)

102 mm (4") heavy, metal exhaust vent

Elbows:

■ 45° elbows provide better airow than 90° elbows.

■ Plan installation to use the fewest number of elbows

and turns.

■ Allow as much room as possible when using elbows

or making turns. Bend vent gradually to avoid kinking.

■ Vent outlet is located at the center of the bottom dryer back.

■ The vent can be routed up, down, left, right, behind the

dryer, or straight out the back of the dryer.

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with

screws or other fastening devices that extend into interior

of duct and catch lint. Do not use duct tape.

Better

Good

NOTES:

n Although usually each single-load dryer should have

an unobstructed outdoor air opening of 24 in.

2

(154 cm

2

)

(based on 1 in.

2

[6.5 cm

2

] per 1,000 Btu [252 kcal]), common

makeup air openings are also acceptable. Set up common

openings so the makeup air is distributed equally to all of

the dryers. Keep in mind that the coverage area must be

increased by 33% to account for the use of registers or

louvers over the openings. Also, makeup air openings

should not be installed near the location where exhaust

vents exit the building.

n If using an existing vent system, clean lint from entire length

of the system and make sure exhaust hood is not plugged

with lint. Replace plastic or metal foil vents with rigid metal

or exible metal vents. Review “Vent System Chart” and,

if necessary, modify existing vent system to achieve best

drying performance.

13

12" min.

(305 mm)

102 mm (4") Diameter Exhaust Hoods

Box hood Louvered hood Angled hood

Vent Hoods

VENTING REQUIREMENTS

Exhaust hood must be at least 305 mm (12") from the ground

or any object that may be in the path of the exhaust (such as

owers, rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of 90˚ Turns

Box and

Louvered Hood

Angled Hood

0 39.6 m (130 ft.) 39.3 m (129 ft.)

1 38.1 m (125 ft.) 36.3 m (119 ft.)

2 35.1 m (115 ft.) 33.2 m (109 ft.)

3 32.3 m (106 ft.) 30.5 m (100 ft.)

4 29.9 m (98 ft.) 28.0 m (92 ft.)

For vent systems not covered by the “Vent System Chart,”

see your parts distributor.

Provision must be made for enough air for combustion

and ventilation. (Check governing codes and ordinances.)

See “Recessed Area and Closet Installation Instructions”

in the “Location” section.

A 102 mm (4") outlet hood is preferred. However, a 64 mm

(2

1

⁄

2

") outlet exhaust hood may be used. A 64 mm (2

1

⁄

2

") outlet

creates greater back pressure than other hood types. For

permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 102 mm (4") clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 102 mm (4") clamp.

5. Move dryer into nal position. Do not crush or kink vent.

Make sure dryer is level.

Vent collar

305 mm min.

(12")

14

The outside end of main vent should have a sweep elbow

directed downward.

If main vent travels vertically through the roof, rather than

through wall, install a 180° sweep elbow on end of vent at least

610 mm (2 ft.) above surface of roof.

The opening in wall or roof shall have a diameter 13 mm (1⁄2")

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

A main vent can be used for venting a group of dryers. The

main vent should be sized to remove 5663 l/min. (200 CFM)

of air per dryer. Large-capacity lint screens of proper design

may be used in main vent if checked and cleaned frequently.

The room where the dryers are located should have make-up

air equal to or greater than CFM of all the dryers in the room.

A Back-draft Damper Kit is available from your distributor and

should be installed in the vent of each dryer to keep exhausted

air from returning into dryers and to keep exhaust in balance

within main vent. Unobstructed return air openings are required.

Each vent should enter the main vent at an angle pointing in

the direction of the airow. Vents entering from the opposite

side should be staggered to reduce the exhausted air from

interfering with the other vents.

The maximum angle of each vent entering the main vent should

be no more than 30°.

Keep air openings free of dry-cleaning uid fumes. Fumes

create acids which, when drawn through the dryer heating

units, can damage dryers and items being dried.

A clean-out cover should be located on the main vent for

periodic cleaning of the vent system.

If an Exhaust Hood Cannot Be Used Multiple Dryer Venting

VENTING REQUIREMENTS

30˚ max.

Air ow

* Minimum clearance above

any accumulation of snow,

ice, or debris such as leaves

1. Remove red cap from gas pipe.

2. Connect gas supply to dryer. If the exible gas hose has

10 mm (3/8") BSP thread, use the supplied conversion thread

adapter. Use pipe-joint compound resistant to the action

of L.P. gas for gas connections.

If necessary for service, open the toe panel. Use a putty knife

to press on the 2 toe panel locks located at the top of the toe

panel. Pull downward on the toe panel to open. Toe panel is

hinged at the bottom.

Make Gas Connection

GAS SUPPLY REQUIREMENTS

3. Open the shut-off valve in the gas supply line.

4. Test all connections by brushing on an approved

noncorrosive leak-detection solution. Bubbles will show

a leak. Correct any leaks found.

15

INSTALLING LEVELING LEGS, PAYMENT DEVICE, AND COIN BOX

The payment device, control panel lock and key, and coin box

lock and key are not included and are available from usual

industry sources.

1. Prepare dryer for leveling legs

NOTE: Slide dryer onto cardboard or hardboard before moving

to avoid damaging oor covering.

Using two or more people, move dryer to desired installation

location.

Take tape off front corners of dryer. Open dryer and remove

the literature and parts packages. Wipe drum interior with damp

cloth to remove any dust.

Take two cardboard corners from the dryer carton and place

them on the oor in back of the dryer. Firmly grasp body of the

dryer and gently lay it on its back on the cardboard corners.

2. Screw in leveling legs

Examine leveling legs and nd diamond

marking. Screw legs into leg holes by

hand. Use an adjustable wrench or

25 mm (1") hex-head socket wrench to

nish turning legs until diamond marking

is no longer visible. Then t a covered foot

boot over each leg foot. A longer leveling foot

(Part Number 279810) is available if needed

on extremely sloped oors.

To protect the oor, use a large piece of cardboard from the

dryer carton. Stand dryer up on the cardboard. Slide the dryer

until it is close to its nal location. Leave enough room for

electrical connection and to connect the exhaust vent.

3. Install payment device and coin box

Remove the service door of the meter case by lifting

it up at the back. If applicable, install the money-accepting

device. (Refer to manufacturer’s instructions for proper

installation.)

Replace the meter case service door. Put the coin vault

with lock and key in the meter case opening.

Remove cardboard or hardboard from under dryer. Adjust

the legs of the dryer up or down until the dryer is level.

Foot

Diamond

marking

16

1. Remove cardboard from beneath dryer. Place a level on top

edges of dryer, checking each side and front. If not level, tip

dryer and adjust feet up or down as shown in Steps 3 and 4,

repeating as necessary.

LEVELING

Leveling your dryer properly reduces excess noise and vibration.

Not Level LEVEL Not Level

2. Grip dryer from top and rock back and forth, making sure all

four feet are rmly on oor. Repeat, rocking dryer from side

to side. If dryer rocks, go to Step 3 and adjust leveling feet.

If all four feet are in rm contact with oor, go to Step 4.

4. When dryer is level and all four feet are rmly in contact

with the oor, use a 25 mm or 1" open-end or adjustable

wrench to turn nuts on leveling feet tightly against dryer

cabinet.

HELPFUL TIP: You may want to prop dryer with wooden

block.

3. If dryer is not level, remove the rubber boot if used; then use

an adjustable wrench or 25 mm (1") hex-head socket wrench

to turn legs until adjustment is completed. Check levelness of

dryer after all feet are rmly touching the ground and the level

shows dryer top to be level front to back and side to side.

HELPFUL TIP: You may want to prop up front of dryer

about 102 mm (4") with a wood block or similar object

that will support weight of dryer.

17

1. Check the electrical requirements. Be sure that you have

the correct electrical supply and the recommended earthing

method. See “Electrical Requirements.”

2. Check that all parts are now installed. If there is an extra part,

go back through the steps.

3. Check that you have all of your tools.

4. Dispose of/recycle all packaging materials.

5. Plug into an earthed outlet, or connect power.

COMPLETE INSTALLATION

6. Check dryer operation. Using a full heat cycle, let the dryer

run for at least ve minutes. Dryer will stop when time is

used up.

NOTE: Dryer door must be closed for dryer to operate. When

door is open, dryer stops, but timer continues to run. To restart

dryer, close door and press cycle keypad.

7. If the burner does not ignite and you can feel no heat

inside the dryer, shut off dryer for ve minutes. Check that

all supply valve controls are in “ON” position and that the

electrical cord is plugged in. Repeat ve-minute test.

WARNING

Electric Shock Hazard

This dryer must be earthed.

Securely tighten all electrical connections.

Failure to do so can result in death, fire, or

electric shock.

18

REVERSING DOOR SWING (OPTIONAL)

Remove the Door Assembly

1. Place a towel or soft cloth on top of dryer or work space

to avoid scratching of the surface.

2. Remove 3 of the 4 screws that hold the door hinge on the

front panel of the dryer. Partially loosen the remaining screw

with keyhole opening and lift the door off the screw.

3. Lay the door assembly on a previously prepared at surface

with the inside (inner door assembly) facing up, and remove

6 Phillips-head screws to release outer door assembly from

inner door assembly.

NOTE: It is important that you remove only 6 indicated screws.

4. Lift the inner door assembly off outer door assembly.

5. Rotate outer door 180°.

Reverse Hinge

1. Use a small at-blade screwdriver to remove 2 plug

strips from the inner door. Slide the head of the screwdriver

under the plugs, without scratching inner door surface, and

lift up strip.

2. Remove the 4 screws that attach to inner door hinge.

19

REVERSING DOOR SWING (OPTIONAL)

3. Move hinge to other side. Reinstall 4 screws.

4. Reinstall plug strips on opposite side of the inner door.

5. Check for ngerprints on the glass. Clean if necessary.

Replace the Door Assembly

1. Place the inner door assembly inside the outer door

assembly.

2. Reassemble the inner and outer door assemblies with

the 6 screws.

Reverse the Strike

1. Use a small at-blade screwdriver to remove plug strip from

the dryer door opening. Slide the head of the screwdriver

under the plugs, without scratching dryer surface, and lift

up strip.

2. Remove the strike using a Phillips screwdriver.

3. Insert strike on the opposite side.

Reinstall the Door

1. Partially insert the third screw from the top; then slide the

hinge onto this screw while hooking the hinge into the front

panel hole. Reattach door to dryer front panel with the

remaining 3 screws.

2. Check for ngerprints on the glass. Clean if necessary.

3. Close door and check that it latches securely.

20

MAINTENANCE INSTRUCTIONS

n Clean lint screen before and after each cycle.

n Removing accumulated lint:

From inside the dryer cabinet:

Lint should be removed every 2

years or more often, depending

on dryer usage. Cleaning should

be done by a qualied person.

From the exhaust vent:

Lint should be removed every 2

years, or more often, depending

on dryer usage.

n Keep area around dryer clear and free from combustible

materials, gasoline, and other ammable vapors and liquids.

n Keep dryer area clear and free from items that would

obstruct the ow of combustion and ventilation air.

If dryer does not operate, check the following:

n Electrical supply is connected.

n Circuit breaker is not tripped or house fuse is not blown.

n Door is closed. Listen closely to hear the door switch

activate.

n Cycle selection keypad has been pushed rmly and display

shows cycle time.

n Check that gas supply shut-off valves are set in open

position.

Direct all requests for service to the Maytag Commercial

Laundry Distributor that sold the appliance.

When calling, please know the purchase date and the

complete model and serial number of your appliance. This

information will help us to better respond to your request.

IF YOU NEED ASSISTANCE

La page charge ...

Maytag MDG28PNCGW Installation Instructions Manual

Maytag MDG28PNCGW Installation Instructions Manual

dans d''autres langues

Documents connexes

Autres documents