Maytag MHN33PRCWW Guide d'installation

INSTALLATION

INSTRUCTIONS

CommerCial StaCked WaSher/

dryer GaS or eleCtriC

www.maytagcommerciallaundry.com

W10920979A

INSTRUCTIONS

D’INSTALLATION

laveuSe/SéCheuSe SuperpoSéeS

à uSaGe CommerCial

à Gaz ou éleCtrique

INSTRUCCIONES

DE INSTALACIÓN

lavadora/SeCadora ComerCialeS

apiladaS a GaS o eléCtriCaS

TABLE OF CONTENTS

Page

Stacked Washer/Dryer Safety .............. 2

Tools & Parts ............................................ 5

Alternate Parts and Accessories ......... 6

Dimensions/Clearances ....................... 7

Stacked Washer/Gas Dryer

Installation Requirements .................... 8

Stacked Washer/Electric Dryer

Installation Requirements .................. 11

Dryer Venting Requirements ............. 15

Dryer Gas Supply Requirements ...... 18

Installing Stacked Washer/Dryer ...... 19

Washer Drain System .......................... 22

Electric Dryer Electrical

Connections ........................................... 23

Leveling .................................................... 27

Reversing Dryer Door Swing .............. 29

Stacked Washer/Dryer

Maintenance Instructions ................... 32

If You Need Assistance ........................ 33

Electronic Control Setup

Instructions ............................................. 34

Warranty .................................................. 40

TABLE DES MATIÈRES

Page

Sécurité de la laveuse/sécheuse

superposées ............................................ 41

Outils et pièces ..................................... 44

Pièces supplémentaires

et accessoires ........................................ 45

Dimensions/Distances

de dégagement ..................................... 46

Exigences d’installation pour

la laveuse/sécheuse à gaz

superposées ............................................ 47

Exigences d’installation pour la

laveuse/sécheuse électriques

superposées .......................................... 50

Exigences concernant

l’évacuation de la sécheuse .............. 55

Spéciﬁcations de l’alimentation

en gaz de la sécheuse ......................... 58

Installation de la laveuse/sécheuse

superposées ........................................... 59

Système d’évacuation

de la laveuse ........................................... 62

Raccordements de la sécheuse

électrique ................................................ 63

Nivellement .............................................. 67

Inversion du sens d’ouverture

de la porte de la sécheuse ..................69

Instructions d’entretien de la

laveuse/sécheuse superposées .......72

Si vous avez besoin d’assistance ..... 73

Instructions de réglage du tableau

de commande électronique ............... 74

Garantie ................................................... 81

ÍNDICE

Página

Seguridad de la lavadora/

secadora apiladas ................................. 82

Herramientas y piezas .......................... 85

Piezas y accesorios adicionales ...... 86

Dimensiones y espacios libres ......... 87

Requisitos de instalación de la

lavadora/secadora

a gas apiladas ........................................ 88

Requisitos de instalación de

la lavadora/secadora eléctricas

apiladas ................................................... 91

Requisitos de ventilación

de la secadora ....................................... 95

Requisitos del suministro

de gas de la secadora ......................... 98

Instalación de la lavadora/

secadora apiladas ................................. 99

Sistema de desagüe

de la lavadora ....................................... 102

Conexiones eléctricas

de la secadora eléctrica ................... 103

Nivelación ..............................................108

Cómo invertir el cierre

de la puerta de la secadora .............. 110

Instrucciones de mantenimiento

de la lavadora/secadora

apiladas .................................................. 112

Si necesita ayuda ................................ 113

Instrucciones de programación

del control electrónico ...................... 115

Garantía ................................................. 121

2

STACKED WASHER/DRYER SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

follow

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

■ It is recommended that the owner post, in a prominent location, instructions for the customer’s use in the event the customer smells

gas. This information should be obtained from your gas supplier.

■ Post the following warning in a prominent location.

3

STACKED WASHER/DRYER SAFETY

In the State of Massachusetts, the following installation instructions apply:

■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by

the State of Massachusetts.

■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.

■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).

IMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, Part 1, CSA C22.1.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this

or any other appliance.

–

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call the re department.

–

Installation and service must be performed by a qualied installer, service agency, or

the gas supplier.

•

Clear the room, building, or area of all occupants.

4

STACKED WASHER/DRYER SAFETY

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of re, electric shock, or injury to persons when using the washer/dryer, follow basic

precautions, including the following:

WARNING:

SAVE THESE INSTRUCTIONS

■

Read all instructions before using the washer/dryer.

■

Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch re.

■

Do not wash or dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other ammable, or explosive

substances as they give off vapors that could ignite or

explode.

■

Do not add gasoline, dry-cleaning solvents, or other

ammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

■

Do not allow children to play on or in the washer/dryer.

Close supervision of children is necessary when the

washer/dryer is used near children.

■

Before the washer/dryer is removed from service or

discarded, remove the doors to the washer/dryer

compartments.

■

Do not reach into the washer/dryer if the tub, agitator or

drum is moving.

■

Do not install or store the washer/dryer where it will be

exposed to water and/or the weather.

■

Do not tamper with controls.

■

Clean dryer lint screen before or after each load.

■

Under certain conditions, hydrogen gas may be produced

in a hot water system that has not been used for 2 weeks

or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water

system has not been used for such a period, before using

the washing machine, turn on all hot water faucets and let

the water ow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

ammable, do not smoke or use an open ame during

this time.

■

Do not repair or replace any part of the washer/dryer or

attempt any servicing unless specically recommended

in this Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

■

Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

■

Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

■

Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

■

The interior of the machine and dryer exhaust vent should

be cleaned periodically by qualied service personnel.

■

See “Electrical Requirements” section of the Installation

Instructions booklet for grounding instructions.

5

TOOLS & PARTS

Tools Needed:

8" (203 mm) or 10" (254 mm)

Pipe Wrench

8" (203 mm) or 10" (254 mm)

Adjustable Wrench That Opens

to 1" (25 mm)

Flat-Blade Screwdriver Phillips Screwdriver

Torx

®†

T-20 Security

Screwdriver or Bit

1" (25 mm) Hex-Head

Socket Wrench

5⁄16" Socket Wrench

Pliers

(that open to 1

9

/

16

" [39 mm])

Level

Utility Knife

1/4" (6 mm) Nut Driver

Locking Pliers

Caulk Gun and Caulk

(for installing new exhaust vent)

Vent Clamps

Pipe-Joint Compound

Suitable for Gas Type

27" (686 mm) Wood Block

Flashlight (optional)

1/2" (13 mm) and 9/16"

(14 mm) Open-End Wrenches

Ruler or Measuring Tape

Parts Supplied:

Water Inlet Hoses (2)

Inlet Hose Washers (4)

U-Shaped Hose Form

Transit Bolt Hole Plug (4)

Beaded Tie Strap

Drain Hose/Clamp

†

® TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.

6

ALTERNATE PARTS AND ACCESSORIES

Alternate Parts

Your installation may require additional parts. If you are interested in purchasing one of the items listed here, call the toll-free number in

the “If You Need Assistance” section.

If You Have: You Will Need to Buy:

Overhead sewer Standard 20 gal. (76 L) 39" (990 mm) tall drain tub or utility sink, sump pump, and

connectors (available from local plumbing suppliers)

1" (25 mm) standpipe 2" (51 mm) diameter to 1" (25 mm) diameter Standpipe Adapter, Part Number 3363920

Connector Kit Part Number 285835

Drain hose too short Extension Drain Hose, Part Number 285863

Connector Kit Part Number 285835

Lint clogged Drain Drain Protector, Part Number 367031

Connector Kit Part Number 285835

Floor drain system Siphon break, Part Number 285834

Connector Kit (x2) Part Number 285835

Extension Drain Hose, Part Number 285863

Water faucets beyond reach of ﬁll hoses Two longer water ﬁll hoses:

6 ft. (1.8 m) 90° bend hose, Part Number 76314

10 ft. (3.0 m), Part Number 350008

Accessories

Enhance your washer/dryer with these premium accessories.

For more high-quality items or to order,

call 1-800-901-2042 or visit us at

www.maytag.com/accessories.

In Canada, call 1-800-807-6777 or visit us at

www.whirlpoolparts.ca

Part Number Accessory

8212526 Washer drip tray, ﬁts under all

31682 All-purpose appliance cleaner

1903WH Laundry supply storage cart

279818 3-way dryer venting kit

285834 Siphon break kit

7

DIMENSIONS/CLEARANCES

Front View Side View Back View

27"

(686 mm)

1"

(25 mm)

74"

(1880 mm)

1"

(25 mm)

74"

(1880 mm)

51"

(1295 mm)

29.5 "

(751 mm)

1

/2

Clearances

Side Clearances Back/Top Clearances

0"

(0 mm)

0"

(0 mm)

8

Selecting the proper location for your washer/dryer improves

performance and minimizes noise and possible washer “walk.”

Your washer/dryer can be installed in a basement, laundry room,

or recessed area. This washer/dryer is not intended for install in

a mobile home or recreational vehicle. See the “Drain System”

section for more information.

Companion appliance location requirements should also

be considered.

IMPORTANT: Do not install or store the washer/dryer where it will

be exposed to the weather. Do not store or operate the washer/dryer

in temperatures at or below 32°F (0°C). Some water can remain

in the washer and can cause damage in low temperatures. Proper

installation is your responsibility.

You will need:

■ A water heater set to deliver 120°F (49°C) water to the washer.

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the washer.

See the “Electrical Requirements” section.

■ Hot and cold water faucets located within 4 ft. (1.2 m) of the

hot and cold water ﬁll valves, and water pressure of 20–100 psi

(137.9–689.6 kPa).

■ A level ﬂoor with a maximum slope of 1" (25 mm) under entire

washer/dryer. Installing the washer/dryer on soft ﬂoor surfaces,

such as carpets or surfaces with foam backing,

is not recommended.

■ A sturdy and solid ﬂoor to support the washer/dryer with

a total weight (water and load) of 450 lbs (204 kg).

■ A ﬂoor drain under the bulkhead. Prefabricated bulkheads with

electrical outlets, water inlet lines, and drain facilities should be

used only where local codes permit.

Stacked Washer/Gas Dryer Location

STACKED WASHER/GAS DRYER INSTALLATION

REQUIREMENTS

Stacked washer/gas dryer installation clearances:

■ The location must be large enough to allow the washer

and dryer doors to be fully opened.

■ Additional spacing should be considered for ease of installation

and servicing. The doors open more than 180°. The washer

door is not reversible.

■ Additional clearances might be required for wall, door, and

ﬂoor moldings.

■ Additional spacing of 1" (25 mm) on all sides of the washer/

dryer is recommended to reduce noise transfer and to improve

spin-up performance of the washer.

■ Companion appliance spacing should also be considered.

When installing a gas dryer:

IMPORTANT: Observe all governing codes and ordinances.

■ Check code requirements: Some codes limit or do not

permit installation of clothes dryers in garages, closets,

or sleeping quarters. Contact your local building inspector.

■ Make sure that lower edges of the cabinet, plus the back and

bottom sides of the washer, are free of obstructions to permit

adequate clearance of air openings for combustion air. See the

“Recessed Area and Closet Installation Instructions” below for

minimum spacing requirements.

Recessed Area Installation Instructions

This washer/dryer may be installed in a recessed area. For recessed

area installations, minimum clearances can be found on the warning

label on the rear of the dryer or in the “Dimensions/Clearances”

section.

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

NOTE: The dryer must be exhausted outdoors.

9

Stacked Washer/Gas Dryer Grounding

IMPORTANT: The washer/dryer must be electrically grounded in

accordance with local codes and ordinances or, in the absence

of local codes, with the National Electrical Code, ANSI/NFPA 70,

latest edition, or Canadian Electrical Code, CSA C22.1. If codes

permit and a separate ground wire is used, it is recommended that

a qualiﬁed electrical installer determine that the ground path

is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

■ Do not ground to a gas pipe.

■ Do not have a fuse in the neutral or ground circuit.

■ A 120 volt, 60 Hz, AC only, 15- or 20-amp, fused electrical

circuit is required. A time-delay fuse or circuit breaker is also

recommended. It is recommended that a separate circuit

serving only this washer/dryer be provided.

■ This washer/dryer is equipped with a power supply cord having

a 3 prong grounding plug.

■ To minimize the possibility of shock, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of

the customer to have the properly grounded outlet installed by

a qualiﬁed electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the

ground path is adequate.

■ Check with a qualiﬁed electrician if you are not sure the

washer/dryer is properly grounded.

STACKED WASHER/GAS DRYER INSTALLATION

REQUIREMENTS

Stacked Washer/Gas Dryer Electrical Requirements

10

IMPORTANT: Observe all governing codes and ordinances.

This installation must conform with all local codes and ordinances.

In the absence of local codes, installation must conform with

American National Standard, National Fuel Gas Code ANSI

Z223.1/NFPA 54 or CAN/CSA B149.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park, Quincy, MA 02269

CSA International

8501 East Pleasant Valley Road

Cleveland, Ohio 44131-5575

The design of this washer/dryer has been certiﬁed by CSA

International for use at altitudes up to 10,000 feet (3,048 m) above

sea level at the B.T.U. rating indicated on the model/serial plate.

Burner input adjustments are not required when the washer/dryer

is operated up to this elevation.

When installed above 10,000 feet (3,048 m), a four percent (4%)

reduction of the burner B.T.U. rating shown on the model/serial

plate is required for each 1,000 foot (305 m) increase in elevation.

For assistance when converting to other gas types and/or installing

above 10,000 feet (3,048 m) elevation, contact your local service

company.

WARNING

Explosion Hazard

Use a new CSA International approved gas supply line.

Install a shut-off valve.

Securely tighten all gas connections.

If connected to propane, have a qualified person make

sure gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Stacked Washer/Gas Dryer Gas Supply

STACKED WASHER/GAS DRYER INSTALLATION

REQUIREMENTS

11

Selecting the proper location for your washer/dryer improves

performance and minimizes noise and possible washer “walk.”

Your washer/dryer can be installed in a basement, laundry room,

or recessed area. This washer/dryer is not intended for install in

a mobile home or recreational vehicle. See the “Drain System”

section.

Companion appliance location requirements should also be

considered.

IMPORTANT: Do not install or store the washer/dryer where it will

be exposed to the weather. Do not store or operate the washer/dryer

in temperatures at or below 32°F (0°C). Some water can remain

in the washer and can cause damage in low temperatures. Proper

installation is your responsibility.

You will need:

■ A water heater set to deliver 120°F (49°C) water to the washer.

■ A grounded electrical outlet located within 6 ft. (1.8 m) of

where the power cord is attached to the back of the washer.

See “Electrical Requirements.”

■ Hot and cold water faucets located within 4 ft. (1.2 m)

of the hot and cold water ﬁll valves, and water pressure

of 20–100 psi (137.9–689.6 kPa).

■ A level ﬂoor with a maximum slope of 1" (25 mm) under entire

washer/dryer. Installing the washer/dryer on soft ﬂoor surfaces,

such as carpets or surfaces with foam backing,

is not recommended.

■ A sturdy and solid ﬂoor to support the washer/dryer with a total

weight (water and load) of 450 lbs (204 kg).

■ A ﬂoor drain under the bulkhead. Prefabricated bulkheads with

electrical outlets, water inlet lines, and drain facilities should be

used only where local codes permit.

Stacked Washer/Electric Dryer Location

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

Stacked washer/electric dryer installation clearances

■ The location must be large enough to allow the washer and

dryer doors to be fully opened.

■ Additional spacing should be considered for ease of installation

and servicing. The doors open more than 180°. The washer

door is not reversible.

■ Additional clearances might be required for wall, door, and ﬂoor

moldings.

■ Additional spacing of 1" (25 mm) on all sides of the washer/

dryer is recommended to reduce noise transfer, and improve

spin-up performance of washer.

■ Companion appliance spacing should also be considered.

Recessed Area and Closet Installation Instructions

This washer/dryer may be installed in a recessed area or closet.

For recessed area and closet installations, minimum clearances

can be found on the warning label on the rear of the dryer.

The installation spacing is in inches and is the minimum allowable.

Additional spacing should be considered for ease of installation,

servicing, and compliance with local codes and ordinances.

NOTE: The dryer must be exhausted outdoors.

12

■ Do not have a fuse in the neutral or ground circuit.

■ This washer/dryer is equipped with a power supply cord having

a 3 prong grounding plug.

■ To minimize the possibility of shock, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation of

the customer to have the properly grounded outlet installed by

a qualiﬁed electrician.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate.

■ Check with a qualiﬁed electrician if you are not sure the washer

is properly grounded.

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

Stacked Washer/Electric Dryer Electrical Requirements

Stacked Washer/Electric Dryer Grounding

Washer Electrical Requirements

13

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

It is your responsibility:

■ To contact a qualiﬁed electrical installer.

■ To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

■ The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved in

remodeling after 1996, and all mobile home installations.

■ A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■ To supply the required 3- or 4-wire, single phase, 240 volt,

60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt

electrical supply, if speciﬁed on the serial/rating plate) on a

separate 30 amp circuit, fused on both sides of the line. A time

delay fuse or circuit breaker is recommended. Connect to an

individual branch circuit. Do not have a fuse in the neutral or

grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor is

permanently connected to the neutral conductor (white wire)

within the dryer. If the dryer is installed with a 4-wire electrical

supply connection, the neutral ground conductor must be

removed from the external ground connector (green screw),

and secured under the neutral terminal (center or white wire)

of the terminal block. When the neutral ground conductor is

secured under the neutral terminal (center or white wire) of the

terminal block, the dryer cabinet is isolated from the neutral

conductor.

■ If local codes do not permit the connection of a neutral ground

wire to the neutral wire, see the “Optional 3-wire connection”

section.

■ A 4-wire power supply connection must be

used when the appliance is installed in a location where

grounding through the neutral conductor is prohibited.

Grounding through the neutral is prohibited for (1) new branch-

circuit installations, (2) mobile homes, (3) recreational vehicles,

and (4) areas where local codes prohibit grounding through the

neutral conductor.

Electric Dryer Power Supply Cord

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes

dryers. The kit should contain:

■ A UL listed 30 amp power supply cord, rated 240 volt

minimum. The cord should be type SRD or SRDT and be at

least 4 ft. (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or “U” shaped spade terminals with

upturned ends.

■ A UL listed strain relief.

If your outlet looks like this:

4-wire

receptacle

(14-30R)

3-wire

receptacle

(10-30R)

Then choose a 4-wire power supply cord with ring or

spade terminals and UL listed strain relief. The 4-wire

power supply cord, at least 4 ft. (1.22 m) long, must

have four 10-gauge copper wires and match a 4-wire

receptacle of NEMA Type 14-30R. The ground wire

(ground conductor) may be either green or bare.

The neutral conductor must be identiﬁed by a white

cover.

Then choose a 3-wire power supply cord with ring or

spade terminals and UL listed strain relief. The 3-wire

power supply cord, at least 4 ft. (1.22 m) long, must

have three 10-gauge copper wires and match a

3-wire receptacle of NEMA Type 10-30R.

If your outlet looks like this:

Dryer Electrical Requirements

14

Fire Hazard

Use 10 gauge copper wire.

Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected

to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (gold).

Securely tighten all electrical connections.

Failure to do so can result in death, re, or

electrical shock.

Dryer Direct Wire

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

■ Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with ﬂexible metallic conduit. All

current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum).

■ At least 5 ft. (1.52 m) long.

STACKED WASHER/ELECTRIC DRYER INSTALLATION

REQUIREMENTS

15

DRYER VENTING REQUIREMENTS

WARNING: To reduce the risk of ﬁre, this dryer must be exhausted

outdoors.

IMPORTANT: Observe all governing codes and ordinances.

Dryer exhaust must not be connected into any gas vent, chimney,

wall, ceiling, attic, crawlspace, or a concealed space of a building.

Only rigid or ﬂexible metal vent shall be used for exhausting.

■ Only a 4" (102 mm) heavy, metal exhaust vent and clamps may

be used.

■ Do not use plastic or metal foil vent.

Rigid metal vent:

■ Recommended for best drying performance and to avoid

crushing and kinking.

Flexible metal vent: (Acceptable only if accessible to clean)

■ Must be fully extended and supported in ﬁnal dryer location.

■ Remove excess to avoid sagging and kinking that may result in

reduced airﬂow and poor performance.

■ Do not install in enclosed walls, ceilings, or ﬂoors.

■ The total length should not exceed 7

3

⁄

4

ft. (2.4 m).

NOTE: If using an existing vent system, clean lint from entire length

of the system and make sure exhaust hood is not plugged with lint.

Replace plastic or metal foil vents with rigid metal or ﬂexible metal

vents. Review the “Vent System Chart” and if necessary, modify

existing vent system to achieve best drying performance.

4"

(102 mm)

4" (102 mm) heavy, metal exhaust vent

Elbows:

■ 45° elbows provide better airﬂow than 90° elbows.

Good

Better

Clamps:

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws

or other fastening devices that extend into interior of duct and

catch lint. Do not use duct tape.

16

4" (102 mm) Diameter Exhaust Hoods

box hood louvered hood angled hood

Vent Hoods

DRYER VENTING REQUIREMENTS

Exhaust hood must be at least 12" (305 mm) from the ground or

any object that may be in the path of the exhaust (such as ﬂowers,

rocks, bushes, or snow).

Maximum Vent Length/Vent Connection

Maximum length of vent system depends upon the type of vent

used, number of elbows, and type of exhaust hood.

Vent System Chart (Rigid Metal Vent)

No. of

90˚ Turns

Box and

Louvered Hoods

Angled

Hood

0 135 ft. (41.2 m) 129 ft. (39.3 m)

1 125 ft. (38.1 m) 119 ft. (36.3 m)

2 115 ft. (35.1 m) 109 ft. (33.2 m)

3 106 ft. (32.3 m) 100 ft. (30.5 m)

4 98 ft. (29.9 m) 92 ft. (28.0 m)

For vent systems not covered by the vent speciﬁcation chart, see

your parts distributor.

Provision must be made for enough air for combustion and

ventilation. (Check governing codes and ordinances.) See the

“Recessed Area and Closet Installation Instructions” in the

“Stacked Washer/Gas Dryer Location” and “Stacked Washer/

Electric Dryer Location” sections.

A 4" (102 mm) outlet hood is preferred. However, a 2

1

⁄

2

" (64 mm)

outlet exhaust hood may be used. A 2

1

⁄

2

" (64 mm) outlet creates

greater back pressure than other hood types.

For permanent installation, a stationary vent system is required.

Connect Vent

1. If connecting to existing vent, make sure the vent is clean.

2. Using a 4" (102 mm) clamp, connect vent to exhaust outlet

in dryer.

NOTE: Do not remove vent collar.

Vent System Length

3. Tighten hose clamp with Phillips screwdriver.

4. Make sure the vent is secured to exhaust hood with

a 4" (102 mm) clamp.

5. Move dryer into ﬁnal position. Do not crush or kink vent. Make

sure dryer is level.

12" min.

(305 mm)

Vent collar

17

The outside end of main vent should have a sweep elbow directed

downward.

If main vent travels vertically through the roof, rather than through

wall, install a 180° sweep elbow on end of vent at least

2 ft. (610 mm) above surface of roof.

The opening in wall or roof shall have a diameter 1⁄2" (13 mm)

larger than vent diameter. Vent should be centered in opening.

Do not install screening over end of vent for best performance.

12" min.

(305 mm)*

A main vent can be used for venting a group of dryers. The main

vent should be sized to remove 200 CFM of air per dryer. Large-

capacity lint screens of proper design may be used in main vent

if checked and cleaned frequently. The room where the dryers are

located should have make-up air equal to or greater than CFM of

all the dryers in the room.

Back-draft Damper Kit, Part No. 3391910, is available from

your distributor and should be installed in the vent of each dryer to

keep exhausted air from returning into dryers and to keep exhaust

in balance within main vent. Unobstructed return air openings are

required.

If an Exhaust Hood Cannot be Used

Multiple Dryer Venting

DRYER VENTING REQUIREMENTS

Each vent should enter the main vent at an angle pointing in the

direction of the airﬂow. Vents entering from the opposite side

should be staggered to reduce the exhausted air from interfering

with the other vents.

The maximum angle of each vent entering the main vent should be

no more than 30°.

24" min.

(610 mm)

30˚ max.

Air ow

* Minimum clearance above any

accumulation of snow, ice, or

debris such as leaves

18

This dryer is equipped for use with natural gas. It is design-certiﬁed by CSA International for propane and butane gases with appropriate

conversion. No attempt shall be made to convert dryer from gas speciﬁed on serial/rating plate for use with a different gas without consulting

the serving gas supplier.

Conversion must be done by a qualiﬁed service technician.

Gas conversion kit part numbers are listed on gas valve burner base.

Type of Gas

DRYER GAS SUPPLY REQUIREMENTS

Recommended Method

Provide a gas supply line of 1⁄2" (13 mm) rigid (IPS) pipe to dryer

location. Pipe joint compounds that resist action of propane gas

must be used. Do not use TEFLON

®†

tape. With propage gas, piping

or tubing size can be 1⁄2" (13 mm) minimum. Usually, propane gas

suppliers determine size and materials used in the system.

Gas Supply Pressure Testing

A 1/8" (3 mm) NPT minimum plugged tapping, accessible for

gauge testing, must be installed immediately downstream of the

installed shut-off valve to the dryer (as shown above). The dryer

must be disconnected from the gas supply piping system during

any pressure testing of the system at test pressures in excess of

1/2" psig (352 kg/m

2

).

Alternate Method

The gas supply may also be connected using 3⁄8" (10 mm)

approved copper or aluminum tubing. If the total length of

the supply line is more than 20 ft. (6.1 m), larger tubing will

be required.

If using natural gas, do not use copper tubing. Pipe joint

compounds that resist action of type of gas supplied must

be used.

Shut-off valve required

The supply line must be equipped with a manual shut-off valve

installed within 6 ft. (1.8 m) of dryer in accordance with National

Fuel Gas Code, ANSI Z223.1. This valve should be located in

same room as dryer. It should be in a location that allows ease

of opening and closing. Do not block access to shut-off valve. In

Canada, an individual manual shut-off valve must be installed in

accordance with the B149 installation codes CAN/CGA B149.1

and CAN/CGA B149.2.

Gas Supply Line

Flexible Metal Appliance Connector

It is recommended that a new ﬂexible stainless steel gas line,

design-certiﬁed by CSA International, be used for connecting the

dryer to the gas supply line. (The gas pipe which extends through

the lower rear of the dryer is provided with 3⁄8" (10 mm) male

pipe thread.)

NOTE: Do not kink or damage the ﬂexible stainless steel gas line

when moving the door.

Rigid Pipe Connection

The rigid pipe connection requires a combination of pipe ﬁttings

to obtain an in-line connection to dryer.

†®TEFLON is a registered trademark of Chemours.

19

4. Models with separate washer power cords: Push the power

cord plug into the opening on the right side of the rear panel and

pull the power cord through the opening on the left side of the

rear panel and close holes with the attached cap. Do not pull

plug end of power cord through the right side hole.

NOTE: To avoid damage to internal washer parts or the power

cord, if the cord does not pull out of the washer rear panel

easily, do not force it. Remove the washer rear panel and guide

the power cord around the obstruction and out the hole on the

left side of the rear panel.

5. Close the bolt holes with the four transport bolt hole plugs.

IMPORTANT: If the washer/dryer is to be transported, call your

product distributor or installer. To avoid suspension and structural

damage, your washer/dryer must be properly set up for relocation

by a trained professional.

INSTALLING STACKED WASHER/DRYER

NOTE: Slide washer/dryer onto cardboard or hardboard before

moving to avoid damaging ﬂoor covering.

IMPORTANT: Position the washer/dryer so that the rear of the

washer is within approximately 3 ft. (900 mm) of its ﬁnal location.

There are four shipping bolts in the rear panel of the washer that

support the suspension system during transportation. These bolts

also retain the power cord inside the washer until the bolts are

removed.

1. Keep the washer/dryer in the upright position while removing the

shipping bolts.

2. Using a 1/2" (13 mm) wrench, loosen each of the bolts.

3.

Once the bolt is loose, move it to the center of the hole and

completely pull out the bolt, including the plastic spacer covering

the bolt. Once all four bolts are removed, discard the bolts and

spacers.

Remove Transport System

20

INSTALLING STACKED WASHER/DRYER

Insert new hose washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

Connect Inlet Hoses to Water Faucets

Make sure the washer drum is empty.

1. Attach a hose to the hot water faucet. Screw on coupling

by hand until it is seated on the washer.

2. Attach a hose to the cold water faucet. Screw on coupling

by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve.

Damage to the valves can result.

Clear Water Lines

■ Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe, or bucket, to get rid of particles

in the water lines that might clog the inlet valve screens.

■ Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

coupling

washer

Connect Inlet Hoses to Washer

1. Attach the cold water hose to the washer’s cold water inlet

valve. Screw on coupling by hand until it is seated on the

washer.

2. Attach the hot water hose to the washer’s hot water inlet valve.

Screw on coupling by hand until it is seated on the washer.

3. Using pliers, tighten the couplings with an additional

two-thirds turn.

NOTE: Do not overtighten. Damage to the valve can result.

4. Turn on the water faucets completely and check for leaks.

NOTE: Replace inlet hoses after 5 years of use to reduce the risk

of hose failure. Record hose installation or replacement dates on

the hoses for future reference. Periodically inspect and replace

hoses if bulges, kinks, cuts, wear, or leaks are found.

Connect Inlet Hoses

La page charge ...

Maytag MHN33PRCWW Guide d'installation

Maytag MHN33PRCWW Guide d'installation

dans d''autres langues

Documents connexes

Autres documents