Maytag EPIC Z MGD9800TQ0 Manuel utilisateur

Marque: Maytag

Modèle: EPIC Z MGD9800TQ0

Catégorie: Sèche-linge

Taper: Manuel utilisateur

Ce manuel convient également à

]VIAYI AG ®

E P IC _TM

FRONT-LOADING GAS DRYER

USE & CARE GUIDE

SECADORA A GAS DE CARGA FRONTAL

MANUAL DE USO Y CUIDADO

p % %

SECHEUSE A GAZ A CHARGEMENT FRONTAL

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEA[URES, OPERATION/PERFORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1.800.688.9900

IN CANADA, CALl: 1.800.807.6777

VISIT OUR WEBSI1E AT WWW.MAYTAG.COM

IN CANADA, WWW.MAY I°AG.CA

SI IIENE PREGUN[AS RESPECTO A [AS CARACTER[STICAS,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVIC[O TECNICO, LI AME AL: 1.800.688.9900

EN CANAD,g,, El AME AL: 1.800.807.6777

VISITE NUESTRO SIT[O WEB EN

_/WW.MAYTAG .COM

EN CANAD,g,, WWW.MAYFAG.CA

AU CANADA, POUR ASSISTANCE, INSTALLA_1ION OU SERVICE,

COMPOSEZ I E : 1.800.807.6777

OU VISITEZ NOTRE SITE INTERNET ,_

WWW.MAYTAG .CA

W10139630A

_£:iiiiiiiiiiiiii@£!!@i!!!iiiiiii_ii_!!iiii[£_i_£_i_ _i:i!:_:_i!!iii!!i_ii_i!!_{_!i(!!_!_!_!_!!_iiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_¸¸

TABLE OF CONTENTS

DRYER SAFETY ...................................................................... 3

INSTALLATION INSTRUCTIONS ......................................... 5

Tools and Parts ................................................................... 5

Optional Pedestal ............................................................... 5

kocation Requirements ....................................................... 6

Electrical Requirements ...................................................... 8

Gas Supply Requirements .................................................. 9

Venting Requirements ...................................................... 10

Plan Vent System .............................................................. 12

Install Vent System ........................................................... 1_¢

Install keveling Eegs ......................................................... 1_

Make Gas Connection ...................................................... 14

Connect Vent ................................................................... 14

Level [Dryer ...................................................................... 14

Reverse Door Swing ......................................................... 15

Complete Installation ....................................................... 17

DRYER USE.......................................................................... 18

Starting Your Dryer ........................................................... 18

Stopping Your [Dryer ........................................................ 19

Pausing or Restarting ........................................................ 19

Control I.ocked ................................................................. 19

Drying and Cycle Tips ...................................................... 19

Status [.ights ...................................................................... 20

Cycles .............................................................................. 20

Additional Features .......................................................... 21

Drying Rack ..................................................................... 22

DRYER CARE ...................................................................... 23

Cleaning the Dryer ].ocation ............................................ 2_

Cleaning the Lint Screen .................................................. 23

Cleaning the Dryer Interior ............................................... 24

Removing Accumulated Lint ............................................ 24

Vacation and Moving Care .............................................. 24

Changing the Drum I.ight ................................................. 24

TROUBLESHOOTING ......................................................... 25

ASSISTANCE OR SERVICE ................................................... 27

WARRANTY ........................................................................ 28

INDICE

SEGURIDAD DE LA SECADORA ........................................ 30

INSTRUCCIONES DE INSTALACION ................................ 32

Herrarnientas y piezas ..................................................... 32

Pedestal optional ............................................................ 32

Requisitos de ubicaciGn ................................................... 33

Requisitos elGctricos ........................................................ 35

Requisitos del suministro de gas ...................................... 36

Requisitos de ventilaciGn ................................................. 37

PlanificaciGn del sistema de ventilaciGn .......................... 39

InstalaciGn del sistema de ventilaciGn ............................. 40

InstalaciGn de las patas niveladoras ................................. 41

ConexiGn del suministro de gas ....................................... 41

ConexiGn del ducto de escape ........................................ 42

NivelaciGn de la secadora ............................................... 42

CGmo invertir el cierre de la puerta ................................. 42

Complete la instalaciGn ................................................... 44

USO DE LA SECADORA ..................................................... 45

Puesta en marrha de la secadora ..................................... 45

Detenci6n de la marcha de la secadora .......................... 46

Pausa o reanudaci6n de la marcha .................................. 46

Control bloqueado .......................................................... 47

Sugerencias de ciclos y secado ........................................ 47

kuces de estado ............................................................... 47

Ciclos .............................................................................. 48

Caracter[sticas adicionales ............................................... 49

Estante de secado ............................................................ 50

CUIDADO DE LA SECADORA .......................................... 51

kimpieza del lugar donde est.1 la secadora ...................... 51

I impieza del filtro de pelusa ............................................ 51

I]mpieza del interior de la secadora ................................ 5I

EliminaciGn de pelusa acumulada ................................... 52

Cuidado para las vacaciones y la mudanza ..................... 52

Cambio de la luz del tambor ........................................... 52

SOLUCION DE PROBLEMAS ............................................. 53

AYUDA O SERVICIO TECNICO ......................................... 55

GARANTiA ......................................................................... 56

__!_i!!iiiiiiiiiiiiiiiiiiiiiiiiii!i!!@ii!!!!!!!!!!!!!!!!!ili!i!i!!ii!i!!:_ii[b 5ii!i£@iiii_ii!iiii!_£!iiiiiiiiiiiiiiiiiii_i_!ii!{iiiiiiill¸i_

TABLE DES MATIERES

SECURITI_ DE LA SECHEUSE ............................................... 57

INSTRUCTIONS D'INSTALLATION ................................... 59

Outillage et pi_ces ........................................................... 59

Pi_destal facultatif ............................................................ .-59

Exigences d'emplacement ................................................ 60

SpGcifications 61ectriques ................................................. 62

SpGcifications de I'alimentation en gaz ............................ 6_¢

Exigences concernant 1'Gvacuation .................................. 64

Planification du systGme d'Gvacuation ............................. 66

Installation du systGme d'Gvacuation ................................ 67

Installation des pieds de nivellement ............................... 67

Raccordement au gaz ...................................................... 68

Raccordement du conduit d'Gvacuation .......................... 69

Mise _ niveau de la s_cheuse ........................................... 69

Inversion du sens d'ouverture de la porte ........................ 69

Achever I'installation ....................................................... 71

UTILISATION DE LA SECHEUSE ........................................ 72

Mise en marche de la s6cheuse ....................................... 72

Arr6t de la s6cheuse ......................................................... 73

Pause ou remise en marche ............................................. 73

Verrouillage des commandes ........................................... 74

Conseils pour le s6chage et les programmes .................... 74

T@-noins lumineux ........................................................... 74

Programmes ..................................................................... 75

Caract6ristiques suppl6mentaires ..................................... 76

Grille de s6chage ............................................................. 77

ENTRETIEN DE LA SI_CHEUSE ........................................... 78

Nettoyage de I'emplacement de la s6cheuse ................... 78

Nettoyage du filtre _ charpie ............................................ 78

Nettoyage de I'int6rieur de la s6cheuse ............................ 79

Retrait de la charpie accumul6e ....................................... 79

Pr6cautions _ prendre pour les vacances et

avant un d6m6nagement .................................................. 79

Changement de I'ampoule d'6clairage du tambour ......... 79

DEPANNAGE ...................................................................... 80

ASSISTANCE OU SERVICE .................................................. 82

GARANTIE .......................................................................... 83

2 _l:lllllll_}_!!iii!iiii_ii!!iiiiiiiiiiiiii@%_ii}ii_ii}ii_ii}ii_ii}ii_ii}ii_ii}ii_ii}

i_i_!iii_i_iiIi!iiiiIi!iiiiIi!iiiiIi!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii_)!_}iiiii!!_!_!_!_!_!_!_!_!_!_!_!_i_¸ _ii_ i!i!_iii_1i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i!!!_iiiiiiiiiiiiiiiiiiiiiiiiiiii_:_i!i

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

I WARNING: For your safety, the information in this manual must be followed to minimize

the risk of fire or explosion, or to prevent property damage, personal injury, or death,

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Clear the room, building, or area of all occupants.

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

.... :}

IMPORTANTSAFETYINSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

[] Read all instructions before using the dryer.

[] Do not place items exposed to cooking oils in your dryer.

Items contaminated with cooking oils may contribute to

a chemical reaction that could cause a load to catch fire.

[] Do not dry articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry-

cleaning solvents, or other flammable or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not allow children to play on or in the dryer. Close

supervision of children is necessary when the dryer is

used near children.

[] Before the dryer is removed from service or discarded,

remove the door to the drying compartment.

[] Do not reach into the dryer if the drum is moving.

[] Do not install or store the dryer where it will be exposed

to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or attempt

any servicing unless specifically recommended inthis

Use and Care Guide or in published user-repair

instructions that you understand and have the skills to

carry out.

[] Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric

softener or product.

[] Do not use heat to dry articles containing foam rubber or

similarly textured rubber-like materials.

[] Clean lint screen before or after each load.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust,

and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodically by qualified service personnel.

[] See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

In the State of Massachusetts, the following installation instructions apply:

[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by

the State of Massachusetts.

[] If using a ball valve, it shall be a T-handle type.

[] A flexible gas connector, when used, must not exceed 3 feet.

iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation Code, CSA B149.1.

The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National

Electrical Code, ANSI/NFPA 70 or Canadian Electrical Code, CSA C22.1.

:ili;iiiiiiiiiiiiiiiiiiiiiiiiiiii!iiiiiiiiiIi!iiiiIi!iiiiIi!iiiiIi!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiiii!iiiii_iii!i:iii!_!_!_!_!_i!!ii!_i!_!_!_!_!_i!i_ii!_i!ii!!_!_!_!_!!!g!!>:i_!;i_!!!ii:;>_!_i_!;i_!_i!!!!!!!!!_i_!ii!!!_i!!_!iiiii!_!:!_!!il!!!!!!!ii!_iiiiiii_i¸ !!_!_!_!_!_!_i!i_ii!_i!_ii!!_!_!_!_!_i!i_ii1!_!_!_!_!!_!Ii_i!ii_i_!!!iii!i:iii!!_i!!ii_iiii!!_!_i!i_ii!_i_!ii!ii!!_!_!!i!!:!ii_iiii_iXi_i_i_i!i!iiiii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i!!!iiiiiiiiiiiiiiiiiiiiiiiiiiiii_!i_¸i:

INSTALLATION INSTRUCTIONS

Gather fine required tools and parts before starting installation. Read and follow the

instructions provided with any tools listed here.

• 8" or 10" pipe wrench

• 8" or 10" adjustable wrench (for gas

connections)

• Flat-blade screwdriver

• Adjustable wrench that opens to 1" (2.5

cm) or hex-head socket wrench (for

adjusting dryer feet)

• V2'nut driver or socket wrench

(recommended)

• level

• Knife

• Vent clamps

• Pipe-joint compound resistant to I.P gas

• Caulking gun and compound (for

installing new exhaust vent)

• Pliers

• Tape measure

Are you placing the dryer on a pedestal? You have the option of purchasing pedestals of

different heights separately for this dryer. You may select a 10" (25.4 cm) pedestal or a

15.5" (39.4 cm) pedestal with a storage drawer. The pedestal will add to the total height of the

dryer for a total height of approximately 46" (116.8 cm) or 51.5" (1 "_;0.8cm), respectively.

For a garage installation, you will need to place the 10" (25.4 cm) pedestal at least

9" (22.9 cm) above the floor. You will need to place the 15.5' (?;9,4 cm) pedestal at least

3" (7,6 cm) above the floor.

Parts supplied

Remove [)arts packages from dryer drum. Check that all parts are included.

4 [ewfling legs

NOTE: [::)o not use leveling legs if installing the dryer on a pedestal.

Parts needed

Check local codes and with gas supplier. Check existing gas supply, electrical supply and

venting. Read "Electrical Requirements," "Gas Supply Requirements" and "Venting

Requirements" before purchasing parts.

• For close-clearance installations between 31.5" (80.01 cm) and 37" (93.98 cm), see "Plan

Vent System" section for venting requirements.

(93.98 era)

Optional pedestal ( t5.5" 139.4 cm] model shown)

The pedestals are available in several colors.

lb order, call the dealer from whom you purchased your dryer or refer to the "Assistance or

Service" section.

Pedestal Height Color Part Number

10" (25.4 cm) White MHP1000SQ0

10" (25.4 cm) Black MHP1000SB0

15.5" (39.4 cm) White MHP1500SQ0

15.5" (39.4 cm) Black MHP1500SB0

15.5" (39.4 cm) Pacific Blue MHP1500SK0

Stack Kit

Are you planning to stack your washer and dryer? 1o do so, you will need to purchase a Stack

Kit. To order, call the dealer from whom you purchased your dryer or refer to the "Assistance

or Service" section. Ask for Part Number 8212640.

Mobile home installations require special parts (listed following) that may be ordered by

calling the dealer from whom you purchased your dryer. For further information, please refer

to the "Assistance or Service" section.

• Mobile Home Installation Kit. Ask for Part Number 346764.

• Metal exhaust system hardware.

ExplosionHazard

Keep flammable materials and vapors, such as

gasoline, away from dryer,

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, e×plosion, or fire.

You will need

• A location that allows for proper exhaust installation. A gas dryer must be exhausted to

the outdoors. See "Venting Requirements."

• A grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See

"Electrical Requirements."

• A sturdy floor to support the total dryer weight of 200 Ibs (90.7 kg). The combined weight

of a companion appliance should also be considered.

• A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. If slope is greater

than 1" (2.5 cm), install Extended Dryer Feet Kit, Part Number 279810. Clothes may not

tumble properly, and automatic sensor cycles may not operate correctly if dryer is not

level.

• For a garage installation, you will need to place the dryer at least 18" (46 cm) above the

floon If using a pedestal, you will need 18" (46 cm) to the bottom of the dryer.

Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer

might not shut off at the end of an automatic cycle. This can result in longer drying times.

The dryer must not be installed or stored in an area where it will be exposed to water and/or

weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in

garages, closets, mobile homes or sleeping quarters. Contact your local building inspecton

NOTE: No other fuel-burning appliance can be installed in the same closet as a dryer.

Installation clearances

[he location must be large enough to allow the dryer door to open fully.

Dryer Dimensions

(96.52 cm)

(80 cm) 27"

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

[he following spacing dimensions are recommended for this dryer. This dryer has been tested

for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be

considered for the following reasons:

• Additional spacing should be considered for ease of installation and servicing.

• Additional clearances might be required for wall, door and floor moldings.

• Additional spacing should be considered on all sides of the dryer to reduce noise transfer.

• For closet installation, with a door, minimum ventilation openings in the top and bottom

of the door are required. [ ouvered doors with equivalent ventilation openings are

acceptable.

• Companion appliance spacing should also be considered.

Custom undercounter installation - Dryer only

9" _ _IIW

(9cm) __ _ __ [Z]

38"rnin.

(96.52 cm)

I"* _ -_-..-.-27"---_ _ I"*

2.5 crn (68.6 cm) 2.5 cm

*Required spacing

Closet installation - Dryer only

_'_48 in.2_

(319 cm:

24in.2'

(188cmz) "

I1"'t* 81w_,-18"**1

(2.5cm) (8Ocm)(12.7cm)

_3"*

(7.6cm)

A. Side view - closet or confined area

B. Closet door with vents

*Required spacing

**For side or bottom venting, O" (0 cm) spacing is allowed.

Recessed or closet installation - Dryer on pedestal

I -1''

(2.5 cm) (68.6 cm)

IiI

1".1I*- 31w.-_-Is"**l

(2.5 cm) (2.5 cm) (80 cm) (12.7 cm)

A B

Recommended installation spacing for cabinet installation

• For cabinet installation, with a door, minimum ventilation openings ill tile top of tile

cabinet are required,

" • _,_17.8 cm)

8"*

m) 5 ** 31_/2 11

(12.7cm)(80.0cm)(2.5cm)(2.5cm)(68.6cm)(2.5cm)

(22.9 cm)

* Required spacing

** For side or bottom venting, 0" (0 cm) spacing is allowed.

A. Recessed area

B.Side view - closet or confined are'a

*Required spacing

**For side or bottom venting, O" (0 cm) spacing is allowed.

Recommended installation spacing for recessed or closet installation, with

stacked washer and dryer

The dimensions shown are for the recommended spacing.

*Required spacing

48 irt. 2 *

(310crn2)

gNN-

24 in.2

(155cm2)

3"* (7.6 cm)

-_ _- 1"* (2.5crn)

(12.7crn)

6"* (_5.2 cm)

,>_,,

76" _........

(/93 cm) --

_ 1" --_ _ 27"_1_

(2.5 cm) 68.6 cm

*Required spacing

Mobile home - Additional installation requirements

This dryer is suitable for mobile home installations. The installation must conform to tile

Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280) or

Standard CAN/CSA-Z240 MH.

Mobile home installations require:

[] Metal exhaust system hardware, which is aw_ilable for purchase from your dealer.

[] Mobile Home Installation Kit Part Number 346764. See "tools and Parts" section for

information on ordering.

[] Special provisions must be made in mobile homes to introduce outside air into the dryer.

[he opening (such as a nearby window) should be at least twice as large as the dryer

exhaust opening.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

120 Volt, 60 Hz., AC only, 15- or 20-amp fused electrical supply is required. A time-delay

fuse or circuit breaker is recommended, it is also recommended that a separate circuit

serving only this dryer be provided.

GROUNDING iNSTRUCTiONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or

breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This dryer is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is properly

installed and grounded in accordance with all local codes

and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative

or personnel if you are in doubt as to whether the dryer is

properly grounded. Do not modify the plug provided with the

dryer: if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

SAVE THESE INSTRUCTIONS

Explosion Hazard

Use a new CSA international approved gas supply line.

Install a shut=off valve.

Securely tighten all gas connections.

if connected to LP, have a qualified person make sure

gas pressure does not exceed 13" (33 cm) water

column.

Examples of a qualified person include:

licensed heating personnel,

authorized gas company personnel, and

authorized service personnel.

Failure to do so can result in death, explosion, or fire.

Gas Type

Natural gas:

This dryer is equipped for use with Natural gas. It is design-certified by CSA International for

[P/propane or butane/gases with appropriate conversion.

• Your dryer must have the correct burner for the type of gas in your home. Burner

information is located on the rating plate in the door well of your dryer. If this information

does not agree with the type of gas available, contact your dealer or call the phone

numbers referenced in the "Assistance or Service" section.

LP gas conversion:

Conversion must be made by a qualified technician.

No attempt shall be made to convert the appliance from the gas specified on the model/serial

rating plate for use with a different gas without consulting your gas company.

Gas supply line

• Must include Ws"NPT minimum plugged tapping accessible for test gauge connection,

immediately upstream of the gas connection to the dryer. See illustration.

• _/2"IPS pipe is recommended.

• %" approved aluminum or copper tubing is acceptable for lengths under 20 ft (6.1 m) if

local codes and gas supplier permit.

• If you are using Natural gas, do not use copper tubing.

• lengths over 20 ft (6.1 m) should use larger tubing and a different size adapter fitting.

• If your dryer has been converted to use [P gas, %" ].P compatible copper tubing can be

used. If the total length of the supply line is more than 20 ft (6.1 m), use larger pipe.

NOTE: Pipe-joint compounds that resist the action of I.P gas must be used. Do not use

[EF[.ON _'*tape.

• Must include a shutoff valve:

In the U.S.A.:

An individual manual shutoff valve must be installed within six (6) feet (1.8 m) of the dryer

in accordance with the National Fuel Gas Code, ANSI Z223.1. The location should be

easy to reach for opening and closing.

In Canada:

An individual manual shutoff valve must be installed in accordance with the Bq49.1,

Natural Gas and Propane Installation Code. [t is recommended that an individual manual

shutoff valve be installed within six (6) feet (1.8 m) of the dryer. The location should be

easy to reach for opening and closing.

A C E

B D

A. %" fl_'xible gas connector

B.%" pipe to flare"adapter fitting

C. Vs" NPT mil}imum plugged tapping

D. _/_"NPTgas supply line

E.Gas shutoff valve

t®TEFLON is a legistered trademark of E.I. DLI Pont De Nemouls and Company.

Gas supply connection requirements

• Use an elbow and a %" flare x %" NPT adapter fitting between the flexible gas connector

and the dryer gas pipe, as needed to avoid kinking.

• Use only pipe-joint compound. Do not use TEFLON _* tape.

• This dryer must be connected to the gas supply line with a listed flexible gas connector

that complies with the standard for connectors for gas appliances, ANSI Z21.24 or CSA

6.10.

Burner input requirements

Elevations above 10,000 ft (3,048 m):

• When installed above I0,000 ft (3,048 m) a 4% reduction of the burner Btu rating shown

on the model/serial number plate is required for each ,000 ft (7_;05m) increase in

elevation.

Gas supply pressure testing

• The dryer must be disconnected from the gas supply piping system during pressure testing

at pressures greater than V2psi.

Dryer gas pipe

• The gas pipe that comes out through the rear of your dryer has a 3/8"male pipe thread.

A. ½" NPT gas supply line

B. _" NPT dryer pipe

*NOTE: If the dryer is mounted on a pedestal, the gas pipe height must be an additional 10"

(25.4 cm) or 1.>.._ (39.4 cm) from the floor, depending on the pedestal model. For a garage

installation, the gas pipe height must be an additional 18" (46 cm) from the floor.

¢)

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result in death

or fire.

WARNING: Io reduce the risk of fire, this dryer MUS-] BE EXHAUSTED OUTDOORS.

IMPORTANT: Observe all governing codes and ordinances.

[he dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a

concealed space of a building.

If using an existing vent system

• Clean lint from the entire length of the system and make sure exhaust hood is not plugged

with lint.

• Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.

• Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance.

If this is a new vent system

Vent material

• Use a heavy metal vent. Do not use plastic or metal foil vent.

• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

4" ( 10.2 cm) heavy metal _'xhaust v_'nt

Vent products can be purchased from your dealer or by calling Maytag Services. For more

information, see the "Assistance or Service" section.

Rigid metal vent

• For best drying performance, rigid metal vents are recommended.

• Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

• Flexible metal vents are acceptable only if accessible for cleaning.

• Flexible metal vent must lye fully extended and supported when the dryer is in its final

location.

• Remove excess flexible metal vent to avoid sagging and kinking that may result in

reduced airflow and poor performance.

• Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45 ° elbows provide better airflow than 90 ° elbows.

Clamps

Good Better

Use clamps to seal all joints.

Exhaust vent must not be connected or secured with screws or other fastening devices

that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

(10.2 cm)

A. Louv_'md hood style

B.Box hood style

The angled hood style (shown here) is acceptable.

(10.2 cm)_

v_ 21/2"

(6.4 cm)

• An exhaust hood should cap the vent to keep rodents and insects from entering the home.

• Exhaust hood must lye at least 12" (30.5 cm) from the ground or any object that may be in

the path of the exhaust (such as flowers, rocks or bushes, snow line, etc./.

• Do not use an exhaust hood with a magnetic latch.

improper venting can cause moisture and lint to collect

indoors, which may result in:

[] Moisture damage to woodwork, furniture, paint, wallpaper,

carpets, etc.

[] Housecleaning problems and health problems.

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

_ ...............D

A. Dryer

B. Elbow

C. Wall

D. Fxhaust hood

E. Clamps

£ Rigid metal or flexible metal vent

G. Vent length necessary to connect elbows

H. Exhaust outlet

Optional exhaust installations

This dryer can be converter] to exhaust out the right side, left side or through the bottom. If

you prefer, you may contact your local dealer to have the dryer converted.

Fire Hazard

Cover unused exhaust holes with one of the

following kits:

279818 (white)

279820 (black)

280102 (pacific blue)

Contact your local dealer.

Failure to follow these instructions can result in death,

fire, electrical shock, or serious injury.

A. Standard rear offset exhaust installation

B.Left or right side exhaust installation

C.Bottom exhaust h_stallation

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two close-

clearance installations are shown. Refer to the manufacturer's instructions.

\- _ _iiii.....

I //

i i u

A B

A. Over-the-top installation (also available with one

offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase.

Please see the "Assistance or Service" section to order.

• Over-the-lop Installation:

Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent mismatch):

Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch

Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch

Part Number 4396014- 29" (73.66 cm) to 50" (127 cm) mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home

structure and must not terminate beneath the mobile home. [erminate the exhaust vent

outside.

Determine vent path

• Select the route that will provide the straightest and most direct path outdoors.

• Plan the installation to use the fewest number of elbows and turns.

• When using elbows or making turns, allow as much room as possible.

• Bend vent gradually to avoid kinking.

• Use the fewest 90 ° turns possible.

Determine vent length and elbows needed for best drying performance

• Use tile following Vent system chart to determine type of vent material and hood

combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust

systems longer than those specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and increased energy usage.

]he Vent system chart provides venting requirements that will help to achieve the best drying

performance.

Vent system chart

NOTE: Side and bottom exhaust installations have a 90 ° turn inside the dryer. lb determine

maximum exhaust length, add one 90° turn to the chart.

Number of 90 ° Type of vent Box or Iouvered Angled hoods

turns or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (I 1 m) 28 ft/8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (I 3.4 m) 38 ft (11.6 m)

Flexible metal 27 ff (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ff (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ff (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ff (7 m) 15 ft (4.6 m)

1. Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust

hood with 4" (10.2 cm) clamp.

3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in

"Plan V_nt System." Avoid 90_ turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior of the vent to secure vent.

Excessive Weight Hazard

Use two or more people to move and install dryer.

Failure to do so can result in back or other injury.

[b protect the floor, use a large flat piece of cardboard from the dryer carton. Place

cardboard under the entire back edge of the dryer.

2. Firmlygraspthebodyofthedryer.Gentlylaythedryeronthecardboard.Seeillustration. Acombinationofpipefittingsmustbeusedtoconnectthedryertotheexistinggasline.

Shownisarecommendedconnection.Yourconnectionmaylyedifferent,accordingtothe

supfylylinetype,sizeandlocation.

Examine the leveling legs. Find the diamond marking.

-a

4. Screw the legs into tile leg holes by hand. Use a wrench to finish turning the legs until the 3.

diamond marking is no longer visible.

5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent or gas line.

For mobile home use

Gas dryers must be securely fastened to the floor at the time of installation.

Mobile home installations require a Mobile Home [nstallation Kit. For more information,

please reference the service numbers in the "Assistance or Service" section.

Remove the red cap from the gas pipe.

Using a wrench to tighten, connect the gas supply to the dryer. Use pipe-joint compound

on the threads of all non-flared male fittings. If flexible metal tubing is used, lye sure there

are no kinks.

A. Hated male fitting

B. Non-flared male" fitting

A. ?_" f/e'xib/_" gas connector

B. ?_" dryer pipe

C. %" to _" pipe elbow

D. _" pipe-to-flar_" adapter fitting

Open the shutoff valve in the supply line. The valve is open when the handle is parallel to

the gas pipe.

A. Closed valve

B.Open valve

]bst all connections by brushing on an approved noncorrosive leak-detection solution.

Bubbles will show a leak. Correct any leak found.

1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. ]f connecting to

existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust

outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a

4" (10.2 cm) clamp.

2. Move dryer into its final location. Do not crush or kink vent.

3. (On gas models) Check that there are no kinks in the flexible gas line.

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

' I 0

:_,_ .....

Check the levelness of the dryer. Check levelness first side to side, then front to back.

NOTE: For LP gas connections, you must use pipe-joint compound resistant to the action

of [P gas. Do not use TEFLON '_ tape.

t:_TEFLON is a registeled tlademalk of E.I. Du Pont De Nemours and Company.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs

up or down and check again for levelness.

Youcanchangeyourdoorswingfromaright-sideopeningtoaleft-sideopening,ifdesired. 4. Remove the 6 screws to release the outer door assembly from the inner door assembly

/see illustration). It is important that you remove only the 6 indicated screws.

Remove the door

1. Open the dryer door. Remove the 4 screws that hold the door hinge oil the front panel of

the dryer. [.oosen, but do not remove, the screw with the top keyhole opening last (second

from the top).

A. Dryer

B.Do not remove.

C. Dryer door

lift and pull forward on the door so that the keyhole clears the screw head. Remove the

door.

lay the dryer door on a flat, protected surface with the inside door assembly facing up.

Remove the last screw from Step 1. Remove the 2 screws holding the handle to the door.

lift the inner door assembly off of the outer door assembly. Unsnap the handle from the

outer door assembly, move it to the other side, and snap in. Set the outer door assembly

aside.

Reverse the hinge and hinge bracket

1. Place the inner door, screw head side up, on the work surface.

2. Remove the 4 screws that hold the hinge to the door.

3. Removethe2screwsthatholdthehandlebrackettothedoor. scratchthedryersurface.Liftup.Repeatinthemiddleandatthebottom.Removethe

plugstripinthedooropeningandinsertintheoppositeside.

4. Movehingetotheothersideandreat_achwiththe4screwsremovedinStep2.

5. Movehandlebrackettotheothersideandreattachwiththe2screwsremovedinStep3.

6. Settheinnerdoorassemblyaside.

Reinstalling the door

1. Check for fingerprints on the glass. Clean if necessary.

2. Place the inner door assembly into the outer door assembly. Align the hinge in the

opening on the side. To fit correctly, the inside door assembly edge is completely inside

the outside door assembly edge.

3. Reassemble the inner and outer door assemblies with the 6 screws.

Style 2: Remove the label.

• Peel off the label located on the opposite side of the door opening covering the hinge

mounting holes. Apply the label over the original hinge holes.

Insert a screw in the second opening from the top of the hinge opening and partially

tighten. Hang the door by placing the top hinge keyhole over the second screw head and

tighten the screw. By putting this screw in first, the door will hang in place while you

insert and tighten the remaining 4 screws.

Replace the 2 handle screws for the door handle of the door assembly.

Remove the plug strip or labeh

Style 1: Remove the plug strip.

• Use a small flat-blade screwdriver to remove the plug strip in the door opening. Slide

the head of the screwdriver under the top portion of the plug strip, being certain not to

A. Dryer door

B. Dryer

C. Insert this screw first.

7. Close the door and check that it latches securely.

ml: lele l ssIallalie s

1. Check that all parts are now instal led. If there is an extra part, go back through the steps to 6.

see which step was skipped. 7.

2. Check that you have all of your tools. 8.

3. Check the dryer's final location. Be sure the vent is not crushed or kinked. 9.

4. Check that the dryer is level. See "level Dryer." 10.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

11.

Remove any protective film or tape remaining on the dryer.

Dispose of/recycle all packaging materials.

Read "Dryer Use."

Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only

Temperature setting.

If the dryer will not start, check the following:

• Controls are set ill a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into a grounded 3 prong outlet.

• Electrical supply is connected.

• Household fuse is intact and tight, or circuit breaker has not tripped.

• Dryer door is closed.

When the dryer has been running for 5 minutes, open the dryer door and feel for heat. [f

you feel heat, cancel cycle and close doon If you do not feel heat, turn off the dryer and

check that the gas supply line shutoff valve is open.

• [f the gas supply line shutoff valve is closed, open it, then repeat the 5-minute test as

outlined above.

• [f the gas supply line shutoff valve is open, contact a qualified technician.

PY';i

3:1

5. Plug into a grounded 3 prong outlet. Turn on power.

!! lll:l{!_!!iii!iiii_ii!!iiiiiiiiiiiiii@_i_!_!_!_!i;ii_ii}ii_ii}ii_ii}ii_ii}ii_ii}ii_ii}ii_ii}ii_ii} i@!_!_!_!i!ii;::!!i!!!:i!!!17

DRYER USE

High

AUTOMATIC MANUAL

CONTROL ON _ ) Estimated Ti.... _--

Heavy Duty CYCLES Timed Dry Remaining IO Medium

Wet O Casu Rapid Dry Less Air Only Off

Da'_qP O De[icateJ/(t_O_/ffSuper U _ _/ e ?

Cool Down O Dehcate

DRYNRSS TEMP EXTRA CYCLE

Extra Care 0 LEVEL CARE END

SIGNAL

Control Locked O Hold for 3

second_ to

lock / unlock Pause

control

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in death,

explosion, or fire.

Fire Hazard

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on

it (including cooking oils).

items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle.

Failure to follow these instructions can result in death

or fire.

This manual covers several different models. Your dryer may not have all of the cycles and

features described.

The following is a guide to starting your dryer. Please refer to specific sections of this manual

for more detailed information.

1. Clean lint screen before each load. See "Cleaning the ].int Screen."

2. Place laundry in dryer and shut door.

Rotate the dial to select either an Automatic or Manual Cycle then press the CONTROl.

ON button. The preset settings and drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

• Point the dial to an Automatic Cycle,

Select DRYNESS I.EVEI to adjust how dry you want the load to be. The time displayed

is an estimated length of the cycle based on the Dryness Level selected. As the cycle

runs, the control senses the dryness of the load and adjusts the time automatically for

the selected Dryness Level.

I ore

Less

DRYNESS

LEVEL

NOTE: Time is not adjustable for Automatic Cycles. Pressing the Manual Dry Time l- or +2

buHons will cause a triple beep, indicating that the time cannot be changed.

• Press the EXTRA CARE feature button if this option is desired.

• Press the CYCI.E END SIGNAl button to set signal volume to desired level.

• Press and hold HOlD TO START button until dryer starts (about 1 second).

Once an Automatic Cycle has started, the Extra Care feature and the Cycle End Signal

level can be adjusted. Press the OFF key twice to stop the dryer and clear the settings,

allowing you to select another cycle and Dryness [eveh

How Automatic Cycles Work

This feature improves drying performance with Auto Moisture Sensing Plus, which

advances the cycle as moisture is extracted from clothing. A thermistor (electronic

temperature sensor) and moisture sensing strips in the dryer drum help measure the

amount of moisture in the clothes as they tumble. An electronic control determines the

load type to help save time, avoid overdrying, and increase the accuracy of the end

dryness level. After the first 5 minutes of an automatic cycle, the estimated time display

will adjust based on the approximate load size, cycle, dryness level selected and amount

of moisture left in the clothes. When the clothes have reached approximately 80% of the

dryness level selected, the estimated time display will adjust again, showing the final

drying time. Auto Moisture Sensing Plus takes the guesswork out of drying time and

enhances fabric care.

To use a Manual Cycle

• Rotate the dial to select a Manual Cycle.

Press the MANUAl DRY TIME (- or +) buttons until the desired drying time is displayed.

[_p - or +, and the time will change by 1-minute intervals. Press and hold - or +, and the

time will change by 5-minute intervals. The initial time displayed is the actual drying time.

DRY TIME

NOTE: The Manual Dry Time feature can be used only with Manual Cycles.

• Press TEMP until the desired temperature illuminates.

NOTE: Pressing the Dryness I.evel button will cause the triple beep indicating that this

option is not selectable. Also, a Dryness level is not indicated.

• Press the EXTRA ([ARE feature button if this option is desired.

• Press the CYCI.E END SIGNAl button to set volume to desired level.

• Press and hold HOLD TO START button until dryer starts (about I second).

While a Manual Cycle is running, you can change the settings for Time, 1emperature, the

Extra Care feature, and the Cycle End Signal. Press the OFF button twice to stop the dryer

and clear the settings, allowing you to select another cycle.

TO stop your dryer at any time

Press OFF twice or open the door.

TO pause the dryer at any time

Open the door or press OFF once.

To restart the dryer

Close the door and press and hold HOLD TO START button until dryer starts. ......

NOTE: Drying will continue from where the cycle was interrupted if you close the door and ,i

press Start within 5 minutes, if the cycle is interrupted for more than 5 minutes, the dryer will

shut off. Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to avoid unintended use of the dryer. You can also

use the Control locked feature to avoid unintended cycle or option changes during dryer

operation.

To enable the Control Locked feature when dryer is running:

Press and hold the CYCLE END SIGNAl. button for _ seconds. The control is locked when a

single beep is heard and the Control [.ocked status light is on.

• When the dryer is off, it is not necessary to press the Control On button before activating

the Control [ocked feature.

To unlock:

Press and hold the CYCLE END SIGNAL button for 3 seconds to turn this feature off.

NOTE: When the dryer is running and Control [.ocked is on, the dryer can be stopped by

pressing the Off button, but can't be restarted until the control is unlocked.

...... ==_;; ............. 7' ..... II l:t'_

Select the correct cycle and dryness level or temperature for your load. If an Automatic Cycle

is running, the display shows the estimated cycle time when your dryer is automatically

sensing the dryness level of your load. [f a Manual Cycle is running, the display shows the

exact number of minutes remaining in the cycle.

Cool [::)own tumbles the load without heat during the last few minutes of all cycles. Cool

[::)own makes the loads easier to handle and reduces wrinkling. [he length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If desired, add a fabric softener sheet. Follow package instructions.

• Removetheloadfromthedryerassoonastumblingstopstoreducewrinkling.Thisis

especiallyimportantforpermanentpress,knitsandsyntheticfabrics.

• Avoiddryingheavyworkclotheswithlighterfabrics.Thiscouldcauseoverdryingof

lighterfabrics,leadingtoincreasedshrinkingorwrinkling.

Cycle tips

• Dry most loads using the preset cycle settings.

• Refer to the Automatic or Manual Preset Cycle Settings chart (in the "Cycles" section) for a

guide to drying various loads.

• Drying temperature and Dryness Level are preset when you choose an Automatic

Cycle. You can choose a different dryness level, depending on your load by pressing

the DRYNESS lEVEE button to select MORE or lESS.

• If you wish to adjust the cycle length of a Manual Cycle, you must press the MANUAl

DRY TIME (- or +) buttons. Adjust the temperature of a Manual Cycle by pressing

TEMP until the desired temperature is selected.

NOTE: You cannot choose a Dryness level with Manual Cycles.

C_P _ /I,_/__"'_ __g

You may follow the progress of your dryer with the drying status indicator lights.

Sensing 0

Wet O

Damp O

Cool Down O

Cycle Complete O

Extra Care O

Control Locked O

Sensing

When a cycle is first turned on, tile Sensing light illuminates until a wet item is detected.

• In an Automatic Cycle, if a wet item has not been detected within 10 minutes, the Sensing

light will turn off and the dryer will shut down.

• In a Manual Cycle, if a wet item is not detected after 10 minutes the Wet light turns on

and the selected cycle continues.

Wet

The Wet light will turn on when a wet item has been detected in the dryer. [he Wet light will

remain on until:

• [he damp dry point is reached in an Automatic Cycle.

• [he dryer enters the cool down period in a Manual Cycle.

Damp

The Damp light indicates that the load has reached the damp dry level.

NOTE: The Damp light is not used with Manual Cycles.

Cool Down

The Cool Down light illuminates during the cool down part of the cycle, laundry is cooling

down for ease in handling.

Cycle Complete

The Cycle Complete light illuminates when a drying cycle is finished. If the Extra Care feature

has been selected, the Extra Care feature indicator light will also be on.

The Cycle Complete light turns off 1 hour after the end of a drying cycle (including the Extra

Care cycle of 2 hours), when Off is pressed, or when the door is opened.

Extra Care Feature

[he Extra Care feature light illuminates when this option is selected. This indicator stays on

with the Cycle Complete light.

Control Locked

[he Control Locked light illuminates when this option is enabled.

Indicator lights

Other indicator lights on the control panel show Cycle, ]emperature and Cycle End Signal

settings selected.

The time display will indicate the estimated or actual time remaining in a cycle.

Select the drying cycle that matches the type of load you are drying. See Automatic preset or

Manual preset cycle settings charts.

AUTOMATIC

Heavy Duty

Normal

Casual

Delicate v

Delicate

CYCLES

MANUAL

Timed Dry

, Touchup

I _ Rapid Dry

Cycle Ck;ntrol knob

Automatic Cycles

Automatic Cycles allow you to match the cycle to the load you are drying. See the following

Automatic preset cycle settings chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and automatically adjusts the drying

time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavyweight mixed loads, cotton towels or jeans.

2 0

La page charge ...

Maytag EPIC Z MGD9800TQ0 Manuel utilisateur

Marque: Maytag

Modèle: EPIC Z MGD9800TQ0

Catégorie: Sèche-linge

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag EPIC Z MGD9800TQ0 User manual
español: Maytag EPIC Z MGD9800TQ0 Manual de usuario

Maytag EPIC Z MGD9800TQ0 Manuel utilisateur

Ce manuel convient également à

Maytag EPIC Z MGD9800TQ0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents