Marvel ML24RIS4LS Le manuel du propriétaire

Refrigerator / Freezer

Réfrigérateur / Congélateurs

Refrigeradores / Congeladors

ML24RFP0**

ML24RFS0**

ML24RFP4**

ML24RFS3**

ML24RIP5**

ML24RIS4**

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

ES Instrucciones de instalación, operación y mantenimiento

2

NOTE

!

CAUTION

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

is committed to building a quality product

in an environmentally friendly manner. Our processes are

tightly controlled and closely monitored. We have achieved

certications in ISO 9001 for quality assurance, ISO 14001

for environmental management, and OHSAS 18001 for oc-

cupational health and safety from Lloyd’s Register Quality

Assurance.

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Installing the water supply ...................................................6

Ice-maker operation .............................................................7

Product dimensions ...........................................................8

Starting your appliance ..................................................10

Using your Electronic control ............................................10

Sleep mode ...................................................................10

Turning your appliance "ON" or "OFF" ..........................11

Adjusting the temperature .............................................11

Temperature mode ........................................................11

Control lock ....................................................................11

Temperature sensor error codes ...................................12

Alarms ...........................................................................12

Door ajar ..................................................................12

Power failure .............................................................13

Temperature alarm ....................................................13

Vacation mode ..................................................................13

Overlay door panel installation ........................................14

Shelving congurations ....................................................18

Shelf removal ...................................................................19

Energy saving tips ............................................................19

Care and cleaning .............................................................20

Obtaining service .............................................................20

Troubleshooting refrigerator freezer and ice-maker ..........21

Troubleshooting ice-maker ..............................................22

Warranty ...........................................................................23

!

WARNING

WARNING - You can be killed or seriously injured

if you do not follow these instructions.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

!

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

3

NOTE

!

CAUTION

XXXXXXXXXXXX

!

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

!

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

!

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Warranty Registration

UNPACKING YOUR APPLIANCE

Online registration

available at

www.agamarvel.com

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.agamarvel.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the right

side near the top. (See gure 1).

Figure 1

4

!

CAUTION

!

WARNING

INSTALLING YOUR APPLIANCE

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unob-

structed. Overlay door models with articulated hinges are

intended for built-in applications only.

An optional stacking kit is required to stack products.

Failure to use a stacking kit could result in personal

injury. Contact your dealer or Aga Marvel customer

service at 800-223-3900 to order.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. AGA MARVEL does not recommend

the use of a custom made grille as air ow may be restrict-

ed. (See Figure 2).

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table "A".

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Rear

Leveling

Legs

Figure 2

Front Leveling

Legs

Front Grille,

keep this area

open.

Model Door Style

Minimum

Height

Maximum

Height

ML24 S

33

3

⁄4"

(85.7 cm)

34

3

⁄4"

(88.3 cm)

ML24 P

34"

(86.4 cm)

35"

(88.9 cm)

Table A

5

NOTE

Figure 3

Figure 4

Do not remove

ground prong

INSTALLING YOUR APPLIANCE

Front grille

Front grille screw

Figure 5

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

!

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Figure 6

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

6

• Do not use any thread sealers on these water line t-

tings.

• Reverse osmosis, softened water, and de-ionized water

are not recommended as they will adversely affect the

quality of the ice.

Water

Supply

Line

Clamp and

Screw

Water valve

inlet

Figure 7

Back view of

ice machine

NOTE

!

CAUTION

Water line from water valve

to ice-maker

INSTALLING THE WATER SUPPLY

MODEL ML24RI AND MODEL ML24RF WITH OPTIONAL ICE-MAKER KIT

Compression

tting

Water

supply

line

Water supply

service loop

to shut off

valve)

If you have model ML24RI you have a factory installed ice-

maker.

An optional ice-maker kit (part number S42418151) is avail-

able for model ML24RF which includes all of the necessary

parts for installation. The kit can be obtained from Marvel

customer service by calling 800-223-3900.

Water valve

inlet

Water Supply

Observe and follow all local building codes when installing

this appliance.

Use

1

⁄4" outside diameter copper tubing for your water sup-

ply which is available at any local hardware or plumbing

supply store. Bend the

1

⁄4" copper tubing to suit your instal-

lation being sure not to kink the tubing. Purchase enough

copper tubing length and coil it behind the unit to form a

"service loop" which will allow the appliance to be pulled

out from the installation for servicing or cleaning. Connect

the copper tubing to the "top side" of a cold water pipe to

prevent the ice-maker from plugging with sediment.

A shutoff valve is recommended on the water supply line to

ease servicing the appliance. NOTE: A SELF-PIERCING

TYPE VALVE IS NOT RECOMMENDED as they are prone

to clogging with sediment which will create pressure drop

reducing the water supply to the unit.

Connect the copper tubing water supply to the water valve

inlet with the compression nut tting provided. Secure the

water supply line to the back of the cabinet with the screw

and clamp provided in the corner of the back panel. (See

Figure 7).

Water pressure must be at a minimum of 20 psi for proper

operation and a maximum of 120 psi.

Make certain all water connections are watertight after in-

stallation. Form the tubing so that it will not vibrate against

the cabinet body or kink when your appliance is set in posi-

tion.

7

NOTE

Ice-maker operation

• The unit must be installed level for proper ice-maker

operation.

• The shutoff arm wire must be down in its lowest posi-

tion for the ice-maker to operate. (See Figure 8).

• When the freezer section and ice-maker unit has suf-

ciently cooled, the ice-maker will harvest ice cubes

automatically.

• When the ice bucket is full, the ice-maker will automati-

cally shut off.

• You may manually stop the ice-maker by raising the

shut off arm to the locking position at the up most posi-

tion. (See Figure 8).

Arm down, ice-maker

will operate

Arm up, stops operation

Figure 8

When operation of the appliance is to be discontinued

for any length of time, the ice cube mold in the ice-maker

should be emptied by allowing the ice-maker to dispense

cubes with the water supply turned off.

1. Turn the water supply off.

2. Raise the ice-maker bail arm.

3. Empty the ice bucket.

4. Replace the ice bucket in the unit and lower the bail

arm.

Dispensing of the cubes should occur within 2 hours. After

the ice-cubes dispense - empty, clean, and replace the ice

cube bucket, and raise the bail arm.

ICE-MAKER OPERATION

!

CAUTION

The water supply to the ice-maker must be turned on prior

to turning the ice-maker on. Failure to do so will cause

rapid dry cycling of the ice-maker mold heater resulting in

temperature control issues in the freezer compartment.

It is recommended the ice-maker is shut off when remov-

ing the bucket, or ice may be dispensed onto the freezer

compartment oor.

If the ice is not used regularly, it will clump together with

time. For best ice results, discard ice in the bin as required

and allow the ice-maker to make a new fresh batch of ice.

Shut-off the ice-maker by raising the shut-off arm before

removing the bucket.

Long and short term storage of ice-maker:

8

"A"

"B"

"C"

"D"

"E"

PRODUCT DIMENSIONS

MODEL

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

"A" "B" "C" "D" "E" "F" "G" "H" "J"

ML24R*S

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

23

7

⁄8"

(60.7 cm)

33

3

⁄4" to 34

3

⁄4"

(85.7 to 88.3 cm)

23

⁄32"

(60.2 cm)

25

21

⁄32"

(65.2 cm)

46

13

⁄32"

(117.9 cm)

25

11

⁄16"

(65.2 cm)

ML24R*P

24"

(61 cm)

**34

1

⁄4" to 35

1

⁄4"

(87 to 89.5 cm)

* 24"

(61 cm)

23

7

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

22

7

⁄8"

(58.1 cm)

-

46

1

⁄2"

(118.1 cm)

23

1

⁄8"

(58.7 cm)

DOOR STYLE

(S) Solid Door

(P) Solid Overlay Door (no handle)

Figure 9

Figure 9a

Figure 10

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 10).

9

"F"

"D"

"E"

"H"

"J"

"G"

Water

inlet

Water

inlet

4

7

⁄8"

(12.4 cm)

1

⁄4"

(3.2 cm)

PRODUCT DIMENSIONS

MODEL

PRODUCT DATA

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

ML24R*S 115V/60Hz/15A

140 lbs

(63.6 kg)

ML24R*P 115V/60Hz/15A

140 lbs

(63.6 kg)

* To install (P) models with the door face ush with adja-

cent cabinetry doors, custom decorative panel thickness

cannot exceed

3

⁄4" (19 mm).

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

Figure 11

21

1

⁄2"

(54.6cm)

10

Power Failure

ALARM RESET

Compartment

select

REF

FRZ

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

Sleep mode:

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 12).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, and activating vacation mode), the control must

be awake.

Starting your appliance:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 12).

STARTING YOUR APPLIANCE

Figure 12

Electronic control

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad

Display Area

Lock

keypad

System Status

indicators

NOTE

Your product has an automatic defrost feature that utilizes

an electric heater element. Periodically during defrost you

may observe the following:

• Water dripping and running sounds as a result of the

frost melt.

• Sizzling and popping sounds from water dripping on

the heater element.

• A faint reddish glow in the freezer compartment from

the electric heater element.

These are all “normal” operating characteristics related to

refrigeration product incorporating automatic defrost. They

do not represent any product fault or safety issue.

Using your electronic control:

11

NOTE

warmer respectively. When you have reached your desired

set-point temperature, press the "On/Off" keypad to accept,

or do nothing and the "Set" mode will time-out in 10-sec-

onds accepting the displayed temperature as the new

set-point.

The available set-point temperature range for your appli-

ance is -6°F (-21°C) to 6°F (-14°C) for the freezer com-

partment (ice-maker) and 34°F (1.2°C) to 42°F (5.7°C) for

the refrigerator compartment. If you attempt to adjust the

temperature outside of these ranges you will receive an

audible notication.

Freezer

compartment

selected

Refrigerator

compartment

selected

REF

FRZ

REF

FRZ

Temperatures can be set for each individual compartment

(refrigerator or freezer / ice-maker). To do so you must rst

select the compartment you want to set the temperature for.

You do so by pressing the refrigerator (REF) or freezer

(FRZ) button on the display. When pressed the LED light

will be illuminated for the respective display.

To change the set temperature for a particular compart-

ment, with the compartment enabled and out of sleep

mode, press the "-" or "+" keypads. "SET" will be indi-

cated on the user interface panel and the current set-point

temperature will display and ash. Subsequent presses of

the "-" or "+" keypads will adjust the temperature colder or

Adjusting the temperature:

When initially loading your product with warm contents, it

may take up to 48-hours for the storage compartment tem-

perature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

Turning your appliance ON and OFF:

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

USING YOUR ELECTRONIC CONTROL

Temperature mode:

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc"

then immediately release your nger from the keypad.

NOTE

If the control lock is active (illuminated lock icon) the

control will have to be unlocked before using the key-

pad to reset an alarm condition. See page 11 (Control

Lock) for instructions for unlocking the control.

12

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Refrigerator

Temperature

Sensor

Failed temperature sensor in the

refrigerator compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from com-

partment to prevent spoilage.

Freezer

Temperature

Sensor

Failed temperature sensor in the

freezer compartment. Can lead to

unwanted storage temperatures and/or

spoiled perishable goods.

Call service to have the

temperature sensor replaced and

remove all perishable goods from com-

partment to prevent spoilage.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord

immediately and call service to have

the defrost sensor replaced.

Door Ajar

ALARM RESET

This alarm condition can be reset by closing the door

or momentarily pressing the "On/Off" keypad, (i.e.-if

you are cleaning the storage compartment, etc.). The

alarm will recur in 5-minutes if the alarm condition

persists.

USING YOUR ELECTRONIC CONTROL

Alarms:

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

13

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Vacation mode:

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

USING YOUR ELECTRONIC CONTROL

NOTE

The audible alarm can be muted, for each occurrence, by

pressing the lock keypad.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

14

!

CAUTION

!

WARNING

!

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

!

WARNING

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

Figure 13a

Cabinet

"Z" Bracket

Figure 13

"P" clamp

and screw

Wire connector

see Figure 14

Figure 13b

Bottom of

door

OVERLAY DOOR PANEL INSTALLATION

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

5

⁄8" (15

mm) and

3

⁄4" (18 mm) are accommodated.

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 13b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 14.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

1

⁄2 inch and

remove the hinges and door from the unit.

15

!

CAUTION

Weight of overlay door panel must not exceed 15

pounds (6.8 kg).

Press and hold down this

tab on the wire connector

and pull the connector apart.

OVERLAY DOOR PANEL INSTALLATION

Step 2: Remove the door gasket

With the door laying on a at surface and starting at a

corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 15. Set the gasket

aside on a at surface.

There are 10 holes in the gasket retainer extrusions, (3 on

each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack.

Figure 14

Overlay panel to

be centered on

width of door.

Overlay panel

ush with top

and side of

door.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

Holes in

gasket

retainer.

Figure 15a

Figure 15

Step 3: Cut and drill the overlay panel

Depending on your model cut the overlay door panel to the

dimensions shown in Figures 16 to 19.

16

!

CAUTION

Weight of overlay door panel must not

exceed 15 pounds (6.8 kg).

1

5

⁄32"

(2.9 cm)

1

5

⁄32"

(2.9 cm)

OVERLAY DOOR PANEL INSTALLATION

Clearance for

screw head,

4 places

Hinge side of door

Clearance

for hinge

at top and

bottom

Figure 18

Left Hand Hinged Door

24" (61 cm) wide appliance

Figure 19

Left Hand Hinged Door

24" (61 cm) wide appliance

Top of door

1

3

⁄4"

(4.4 cm)

1

⁄4"

(6 mm)

Deep

1" (2.5 cm) diameter

x

1

⁄4" (6 mm) deep

6 places

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

1

⁄2"

(3.8 cm)

typical

1

11

⁄16"

(4.3 cm)

30

11

⁄32"

(77.1 cm)

1

⁄4" (6 mm)

radius is

permissible

14"

(35.6 cm)

1

3

⁄16"

(3 cm)

3

1

⁄8"

(7.9 cm)

Clearance

for hinge

at top and

bottom

Top of door

Clearance for

screw head,

4 places

Figure 16

Right Hand Hinged Door

24" (61 cm) wide appliance

Hinge side of door

23

3

⁄4"

(60.3 cm)

23

3

⁄4"

(60.3 cm)

Figure 17

Right Hand Hinged Door

24" (61 cm) wide appliance

3

1

⁄8"

(7.9 cm)

1

3

⁄4"

(4.4 cm)

2"

(5.1 cm)

3

11

⁄16"

(9.4 cm)

1

⁄4"

(6 mm)

Deep

30

11

⁄32"

(77.1 cm)

1" (2.5 cm) diameter

x

1

⁄4" (6 mm) deep

4 places

1

⁄2"

(3.8 cm)

typical

1

11

⁄16"

(4.3 cm)

4

7

⁄8"

(12.4 cm)

4

7

⁄8"

(12.4 cm)

14"

(35.6 cm)

1

3

⁄16"

(3 cm)

1

⁄4" (6 mm)

radius is

permissible

This side

facing interior

This side

facing interior

17

OVERLAY DOOR PANEL INSTALLATION

Material Type #10 Wood Screw

Hardwood

1

⁄8" (3.2 mm) Diameter Pilot Hole

Softwood

7

⁄64 (2.8 mm) Diameter Pilot Hole

Table B

Figure 20

#10 x 1/2"

screw

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom overlay panel should be

ush with the top of the door and centered along the width

of the door. See Figure 15a. Drill holes through the gasket

extrusion using the 10 holes as pilot holes. Use the drill

size from the chart in Table "B", being careful not to drill

through the front surface of the panel. If the overlay panel is

thinner than

5

⁄8" (16 mm) thick shorter screws will have to be

obtained. Fasten the panel to the door with the 10 screws

provided in the literature pack. (See Figure 20). Remove

the clamps and replace the gasket in the gasket extrusion

channels of the door. Some force may be required to seat

the gasket into the channels. Be sure the gasket corners

are seated properly.

Step 6: Secure the cabinet

Use the #8 x

3

⁄4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

Step 5: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figures 13 and

13a). Place wire harness from the grille and mount to the

bottom of the door with the screw and "P" clamp removed

in step 1. (See Figure 13b). Reconnect the wire harness,

(See Figure 14).

Figure 21

Cabinet

"Z" bracket

#8 x

3

⁄4" black

screws

(3 places)

18

SHELVING CONFIGURATIONS

Refrigerator / Freezer

24" (61 cm) wide see Figure 22:

Refrigerator:

(2) Half width cantilever adjustable glass shelf.

see Figure 25

(1) Full width xed position glass shelf

(1) Roller glide clear crisper drawer

Freezer:

(1) Fixed position metal shelf, see Figure 27.

Refrigerator / Freezer

24" (61 cm) wide see Figure 24:

Refrigerator:

(2) Half width cantilever adjustable glass shelf.

see Figure 25

(1) Roller glide full width ow thru shelf, Figure 28.

Freezer:

(1) Fixed position metal shelf, see Figure 27.

Refrigerator / Ice-maker

24" (61 cm) wide see Figure 23:

Refrigerator:

(2) Half width cantilever adjustable glass shelf.

(1) Full width xed position glass shelf

(1) Roller glide clear crisper drawer

Freezer:

(1) Ice-maker with ice bucket, see Figure 26.

Figure 22

Figure 25

Frame and at glass shelf

Figure 26

Ice Bucket

RI model only

Figure 27

Freezer shelf

RF model only

Ice-maker

and bucket

Figure 23

Figure 24

Freezer

compartment

19

SHELVING CONFIGURATIONS AND ENERGY SAVING TIPS

To remove the crisper :

Pull out until it stops. Lift up on the front of the pan, and

remove it from the frame.

To Add or Remove a Shelf

Remove stored product from the shelf. Do not try to remove

a loaded shelf from the appliance. Grasp the shelf front with

both hands, rotate the front upward and lift out. (See Figure

29). To install a shelf insert the shelf in the appliance and

insert the top hooks into the shelf support slots and drop

the shelf down so the hooks drop over the bottom of the

slots.

Make sure your cantilever shelf is secure on the shelf sup-

ports by pressing down on the shelf before loading.

!

CAUTION

Grasp the shelf

by the front with both

hands and rotate the front

of the shelf up, then lift the

shelf up and remove the

shelf from the shelf

ladders.

!

CAUTION

Never try to move a loaded shelf, remove everything from

the shelf before moving. Use both hands when moving the

shelf.

Figure 29

Figure 28

The following suggestions will minimize the

cost of operating your refrigeration appliance.

1. Do not install your appliance next to a hot appliance

(cooker, dishwasher, etc.), heating air duct, or other

heat sources.

2. Install product out of direct sunlight.

3. Ensure the front grille vents at front of appliance be-

neath door are not obstructed and kept clean to allow

ventilation for the refrigeration system to expel heat.

4. Plug your appliance into a dedicated power circuit. (Not

shared with other appliances).

5. When initially loading your new product, or whenever

large quantities of warm contents are placed within

refrigerated storage compartment, minimize door

openings for the next 12 hours to allow contents to pull

down to compartment set temperature.

6. Maintaining a relatively full storage compartment will

require less appliance run time than an empty compart-

ment.

7. Ensure door closing is not obstructed by contents

stored in your appliance.

8. Allow hot items to reach room temperature before plac-

ing in product.

9. Minimize door openings and duration of door openings.

10. Use the warmest temperature control set temperature

that meets your personal preference and provides the

proper storage for your stored contents.

11. When on vacation or away from home for extended pe-

riods, set the appliance to warmest acceptable tem-

perature for the stored contents and raise the ice-maker

bail arm to stop ice production.

12. Set the control to the “off” position if cleaning the

appliance requires the door to be open for an extended

period of time.

20

!

CAUTION

CARE AND CLEANING AND OBTAINING SERVICE

Front Grille

Be sure that nothing obstructs the required air ow open-

ings in front of the cabinet. At least once or twice a year,

brush or vacuum lint and dirt from the front grille area (see

page 4).

SHOCK HAZARD: Disconnect electrical power from the

appliance before cleaning with soap and water.

Cabinet

The painted cabinet can be washed with either a mild soap

and water and thoroughly rinsed with clear water. NEVER

use abrasive scouring cleaners.

Interior

Wash interior compartment with mild soap and water. Do

NOT use an abrasive cleaner, solvent, polish cleaner or

undiluted detergent.

Care of Appliance

1. Avoid leaning on the door, you may bend the door

hinges or tip the appliance.

2. Exercise caution when sweeping, vacuuming or mop-

ping near the front of the appliance. Damage to the

grille can occur.

3. Periodically clean the interior of the appliance as

needed.

4. Periodically check and/or clean the front grille as

needed.

In the Event of a Power Failure

If a power failure occurs, try to correct it as soon as pos-

sible. Minimize the number of door openings while the

power is off so as not to adversely affect the appliance's

temperature.

Light assembly replacement

All models use LED lamps to illuminate the interior of the

appliance. This component is very reliable, but should one

fail, contact a qualied service technician for replacement

of the LED.

If Service is Required:

• If the product is within the rst year warranty period

please contact your dealer or call AGA MARVEL Cus-

tomer Service at 800.223.3900 for directions on how to

obtain warranty coverage in your area.

• If the product is outside the rst year warranty period,

AGA MARVEL Customer Service can provide recom-

mendations of service centers in your area. A listing

of authorized service centers is also available at www.

agamarvel.com under the service and support section.

• In all correspondence regarding service, be sure to

give the service number, serial number, and proof of

purchase.

• Try to have information or description of nature of the

problem, how long the appliance has been running, the

room temperature, and any additional information that

may be helpful in quickly solving the problem.

• Table "C" is provided for recording pertinent information

regarding your product for future reference.

For Your Records

Date of Purchase

Dealer’s name

Dealer’s Address

Dealer’s City

Dealer’s State

Dealer’s Zip Code

Appliance Serial Number

Appliance Service Number

Date Warranty Card Sent (Must

be within 10 days of purchase).

Table C

La page charge ...

Marvel ML24RIS4LS Le manuel du propriétaire

Marvel ML24RIS4LS Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents