Sterling 5698-33S-G05 Guide d'installation

Installation and Care Guide

Pivot Shower Door

Français, page “Français-1”

Español, página “Español-1”

5698, 5699

1331204-2A

Tools and Materials

Before You Begin

WARNING: Risk of serious injury. Damage before installation can result in glass shattering.

Inspect the glass and all parts for damage before installation.

WARNING: Risk of serious injury. Improper installation can result in glass shattering. Follow all

installation instructions.

WARNING: Risk of serious injury. Do not cut tempered glass. Tempered glass will shatter if cut.

WARNING: Risk of serious injury. Shower door and side panels can shatter. Regularly inspect the

glass and all parts for damage, missing, or loose parts.

WARNING: Risk of serious injury. Always wear safety glasses while cutting and drilling.

WARNING: Risk of personal injury. Do not cut the tempered glass. If the glass is cut, the glass

will shatter and may cause personal injury.

WARNING: Risk of personal injury or product damage. Unframed tempered glass should not

contact hard surfaces or it may shatter. Do not touch the edge of the tempered glass panel with the

tools or any hard objects. Do not set the unframed tempered glass directly on the ﬂoor.

IMPORTANT! This door is designed to accommodate walls that are less than 3/8″ (10 mm) out of plumb.

Verify the area the door will be attached to is within 3/8″ (10 mm) or better of plumb. The door may not

function properly if the wall is more than 3/8″ (10 mm) out of plumb.

IMPORTANT! Leave this manual for the end user. Read these instructions before installing or using this

product.

Your new Sterling door can be installed with the door opening to either the right or left. Install the

door with the pivot side away from the showerhead for best results.

Before starting the installation, lay out and identify all of the parts. Inspect for damage.

During the installation, protect the ﬂoor of the shower with a drop cloth to avoid damage.

The shower base should be installed and prepared at this time, including ﬁnished wall materials.

Closely follow the instructions pertaining to the sealant application on the door. Sealing areas other

than those shown may cause leaking.

Two people should perform this installation.

32-Teeth

Per Inch Blade

100% Silicone

SealantMiter Box

5/16" Masonry

Bit for TileMasking Tape Tin Snips

5/16"

9/64"

1331204-2A 2 Sterling

Parts Identiﬁcation

Wall Jamb

Strike

Jamb

Bulb Seal

Latch

Panel Assembly

Bottom Seal

Threshold

Pivot Pin

Bushing

Sleeve

Pivot Jamb

1319191

Hardware Pack

Wall Jamb

Sterling 3 1331204-2A

1. Determine the Door Conﬁguration

IMPORTANT! Install the pivot jamb of the door on the side opposite the showerhead.

IMPORTANT! Left side pivot conﬁguration is shown in installation steps unless otherwise indicated.

Determine whether the door will pivot on the right or left side.

Pivot Jamb

Left Pivot

Top View

Right Pivot

Showerhead

Pivot Jamb

1331204-2A 4 Sterling

2. Measure and Cut the Threshold

Cover the drain with tape to prevent the loss of small parts.

Use a drop cloth to protect the shower surface.

Measure distance ″A″ between the shower walls and mark it on the threshold.

Measure 1/16″ (2 mm) or the width of a saw blade from ″A″ and make a second mark on the

threshold as shown.

Cut the threshold at the second mark and ﬁle any rough edges.

A

1/16"

(2 mm)

A

Threshold

"A" Mark

Cut here.

A

Tape Measure

Sterling 5 1331204-2A

3. Position the Threshold

If needed, ﬁle the ends of the threshold to match the corner radius of the shower wall.

Position the threshold 1/4″ (6 mm) from the outside edge of the shower ledge along its entire

length. Mark the location.

Tape the threshold in place.

1/4"

(6 mm)

1331204-2A 6 Sterling

4. Position the Wall Jambs

IMPORTANT! The wall jambs must ﬁt tightly against the threshold and the wall.

Position the wall jambs on the threshold, ﬂush against the threshold lip and the wall.

Plumb the wall jambs.

Tape the wall jambs securely in place and mark its location.

Wall Jamb

Sterling 7 1331204-2A

5. Mark the Wall Jamb Screw Holes

Mark the wall at the four slotted holes on each wall jamb and remove the wall jambs.

1331204-2A 8 Sterling

6. Install the Wall Anchors

Drill a 5/16″ hole at each marked location. Use a masonry bit for tile walls.

Install the provided wall anchors.

Repeat for the opposite wall.

Thoroughly clean the shower base, ﬂoor, threshold, and wall.

1

2

3

Sterling 9 1331204-2A

7. Install the Wall Jambs

IMPORTANT! The round holes on the wall jambs must face the inside of the shower.

Replace the wall jamb.

Secure with the four provided #8-18 x 1-1/2″ screws.

Repeat for the second wall jamb.

#8-18 x1-1/2" Screw

1331204-2A 10 Sterling

8. Install the Latches

Install two latches into the strike jamb with the provided #6-20 x 1/2″ screws.

Strike Jamb

Strike Jamb Latch

#6-20 x 1/2"

Sterling 11 1331204-2A

9. Locate the Strike Jamb

IMPORTANT! Left pivot conﬁguration shown in installation steps unless otherwise indicated.

IMPORTANT! Do not install screws until instructed.

Slide the bulb seal strip completely into the T-slot of the strike jamb.

Fit the strike jamb into the threshold and the wall jamb.

Strike

Jamb

Strike Jamb

Bulb Seal Strip

1331204-2A 12 Sterling

10. Place the Setting Block

Place the setting block on the threshold, ﬂush against the strike jamb.

Setting Block

Sterling 13 1331204-2A

11. Assemble the Hinge Bracket

IMPORTANT! Left pivot conﬁguration shown. Install bushing sleeve and pivot pin to opposite end of

hinge bracket for right pivot installations.

Slide the bushing sleeve completely onto the door panel hinge bracket.

Press the pivot pin into the bottom of the hinge bracket.

Bushing Sleeve

Pivot Pin

1331204-2A 14 Sterling

12. Assemble the Pivot Jamb

Slide the pivot jamb onto the hinge bracket.

NOTE: The bottom of the pivot jamb should be ﬂush with the pivot pin. There should be a gap between

the bottom of the pivot jamb and the bottom of the hinge bracket.

Pivot Jamb

Sterling 15 1331204-2A

13. Install the Pivot Jamb

With help, ﬁt the pivot jamb and panel assembly into the pivot-side wall jamb. Ensure that the

strike end of the glass panel assembly is resting on the setting block.

1331204-2A 16 Sterling

14. Adjust the Jambs

Adjust the jambs as necessary until the door closes as desired.

Make large adjustments by moving the pivot jamb and door panel assembly in or out of the pivot

side wall jamb.

Make ﬁne adjustments by moving the strike jamb in or out of the strike side wall jamb.

Maximum adjustment is reached when the indicator lines on the strike and pivot jambs align with

the edge of the wall jambs.

Indicator

Line

Sterling 17 1331204-2A

15. Secure the Jambs

From the inside of the shower, drill 9/64″ pilot holes into the pivot jamb at the locations of the holes

in the wall jamb.

Secure the pivot jamb with the provided #8-18 x 3/8″ screws through the holes.

Remove the setting block.

Verify that the door closes as desired. Adjust the strike jamb if necessary.

From the inside of the shower, drill 9/64″ pilot holes into the strike jamb at the locations of the

holes in the wall jamb.

Secure the strike jamb with the provided #8-18 x 3/8″ screws through the holes.

1331204-2A 18 Sterling

16. Install the Handles

NOTE: The handle shown may differ from the one included in your shower door.

Assemble the handle.

NOTE: The exposed screwheads face the inside of the shower.

Sterling 19 1331204-2A

17. Install the Bottom Seal

IMPORTANT! If the seal is misshapen when taken out of the packaging, immerse it in warm water until

it regains its proper shape.

Measure the glass panel from hinge bracket to strike jamb.

Cut the bottom seal to this length.

Install the cut length of the bottom seal to the bottom edge of the inside of the glass panel.

Cut 1-1/4″ from the excess bottom seal and install to the bottom edge of the inside of the hinge

bracket.

1-1/4"

(32 mm)

1331204-2A 20 Sterling

La page charge ...

Sterling 5698-33S-G05 Guide d'installation

Ce manuel convient également à

Sterling 5698-33S-G05 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents