Sub-Zero 5310890 Guide d'installation

Designer Series

Undercounter Refrigeration

Installation Guide

SPECIFICATIONS, INSTALLATION,

AND MORE

2 | Sub-Zero Customer Care 800.222.7820

Designer Series Undercounter Refrigeration

Contents

3 Designer Series Undercounter Refrigeration

4 Opening Dimensions

5 Electrical Requirements

6 Plumbing Requirements

6 Preparation

7 Anti-Tip Bracket

7 90° Door Stop

8 Placement

8 Alignment

9 Water Line

10 Door Panel

12 Panel Installation

14 Completion

Features and speciﬁcations are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

Important Note

To ensure this product is installed and operated as safely

and eciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or prod-

uct damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise speciﬁed.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

subzero.com | 3

Designer Series Undercounter Refrigeration

Product Information

Important product information, including the model and

serial number, are listed on the product rating plate. The

rating plate is located inside the cabinet, in the upper left

area of the unit. Refer to the illustration below.

If service is necessary, contact Sub-Zero Factory Certiﬁed

Service with the model and serial number. For the name of

the nearest Sub-Zero Factory Certiﬁed Service or for ques-

tions regarding the installation, visit the Product Support

section of our website, subzero.com, or call Sub-Zero

Customer Care at 800-222-7820.

RATING PLATE

Rating plate location

4 | Sub-Zero Customer Care 800.222.7820

The depth of each model is 23⁄" (587). Allow for panel

thickness when planning the ﬁnished opening depth. A

minimum 3⁄"

(89) ﬁnished return is required on all sides of

the opening. Framed cabinets require additional ﬁnished

ﬁller material behind the face frame for a proper installa-

tion. Refer to the illustration.

DUAL INSTALLATION

If two units are installed side by side, a dual installation kit

may be required. Installations without a custom ﬁller strip

require a dual installation kit. If a dual installation kit is not

speciﬁed, a 2"

(51) ﬁller strip is recommended between the

units. Dual installations without a ﬁller strip can only be

accomplished using two units with opposite hinges. Refer

to the illustrations below.

Dual installation kits are available through an authorized

Sub-Zero dealer. For local dealer information, visit the ﬁnd

a showroom section of our website, subzero.com. For

questions regarding the installation, call Sub-Zero Cus-

tomer Care at 800-222-7820.

DUAL OPENING WIDTH W

Two 24" Models 48" (1219)

Dual installation kit required.

Site Preparation

Opening Dimensions

DESIGNER SERIES UNDERCOUNTER MODELS

W

OPENING WIDTH

H

OPENING

HEIGHT

TOP VIEW

SIDE

VIEW FRONT VIEW

NOTE:

3

1

/2" (89) finished returns will be visible and should be finished to match cabinetry.

3

/4" (19)

TYPICAL

FRAMED

CABINETRY

W

FILLER

3

1

/2" (89)

FINISHED

RETURN

FRAMELESS

CABINETRY

W

3

/4" (19)

TYPICAL

3

1

/2" (89)

FINISHED

RETURN

24" (610)

OPENING

DEPTH

WITHOUT FILLER STRIP

FILLER STRIP

Opposite hinges

Same side hinges

OPENING DIMENSIONS W H

24" Model 24" (610) 34⁄" (876)

subzero.com | 5

Electrical Requirements

Installation must comply with all applicable electrical

codes.

The electrical supply must be located within the shaded

area shown in the illustration below. A separate circuit

servicing only this appliance is required.

IMPORTANT NOTE: For indoor models, a ground fault cir-

cuit interrupter (GFCI) is not recommended and may cause

interruption of operation.

For the outdoor model, a ground fault circuit interrupter

(GFCI) is required to reduce the risk of electrical shock.

The electrical outlet must be positioned with the ground-

ing prong to the right of the thinner blades.

1

/4" (6)

4"

(102)

3"

(76)

9"

(229)

FLOOR

RIGHT SIDE

OF OPENING

Electrical supply location

CAUTION

The outlet must be checked by a qualiﬁed electrician

to be sure it is wired with the correct polarity. Verify

the outlet is properly grounded.

WARNING

If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly quali-

ﬁed persons in order to avoid a hazard.

WARNING

Do not locate multiple portable socket-outlets,

power strip, or portable power supplies at the rear of

the appliance.

WARNING

Do not use an extension cord, two-prong adapter, or

remove the power cord ground prong.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp dedicated circuit

Receptacle 3-prong grounding-type

Site Preparation

6 | Sub-Zero Customer Care 800.222.7820

Plumbing Requirements

MODEL DEU2450CI

Installation must comply with all applicable plumbing

codes.

For ease of installation, recess the water shut o into the

wall or place it in an adjacent cabinet. Locate the water

supply line within the shaded area shown in the illustra-

tion below. Connect the water supply line to the house

supply with an easily accessible shut-o valve. Do not use

self-piercing valves.

An in-line ﬁlter is required when water conditions have a

high sediment content.

A reverse osmosis system can be used provided there is

constant water pressure of 35–120 psi

(2.4–8.3 bar) supplied

to the unit at all times. A copper line is not recommended

for this application.

PLUMBING REQUIREMENTS

Water Supply Line ⁄" OD copper, braided

stainless steel, or PEX tubing

Water Pressure 35–120 psi (2.4–8.3 bar)

Excess Water Line for Connection 5' (1.5 m)

Preparation

Uncrate the unit and inspect for damage. Remove and

recycle packing materials. Do not discard the kickplate,

anti-tip bracket, and hardware.

Remove the kickplate by extracting the two mounting

screws. Refer to the illustration below.

SCREW

Kickplate removal

4"

(102)

3"

(76)

9"

(229)

LEFT SIDE

OF OPENING

AREA EXTENDS

1

/2" (13)

FORWARD ON FLOOR

Water supply location

Site Preparation

subzero.com | 7

90° Door Stop

The door stop pins provided with the unit limit the door

swing to 90°.

IMPORTANT NOTE: If a 90° door opening is desired, the

pins must be installed prior to installing the unit into the

opening.

To install, open the door to approximately 80°. Insert one

hinge pin into each hinge. Refer to the illustration below.

DOOR STOP PIN

90° door stop

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

bracket must be installed.

The anti-tip bracket should be attached to the wall behind

the unit with the bracket ﬂange located ⁄"

(6) above the

top of the unit. Refer to the illustration below. Failure to

properly position the anti-tip bracket will prevent proper

engagement.

1

/4" (6)

ANTI-TIP

BRACKET

Anti-tip bracket

Site Preparation

8 | Sub-Zero Customer Care 800.222.7820

Alignment

LEVELING

Once the unit is in position, rotate the front legs clockwise

to raise and counterclockwise to lower. Rear height adjust-

ment can be made from the front. Using a Phillips drive,

turn clockwise to raise the unit or counterclockwise to

lower. Use the lowest torque setting when using a power

drill. Do not turn the leveling legs by hand. Refer to the

illustration below.

When the unit is properly leveled, door adjustments are

less likely to be necessary.

IMPORTANT NOTE: Level the unit to the ﬂoor, not the

surrounding cabinetry. This could aect the operation of

the unit, such as door closing.

WARNING

To reduce the possibility of the unit tipping forward,

the front leveling legs must be in contact with the

ﬂoor.

REAR

ADJUSTMENT

FRONT

ADJUSTMENT

Leveling

Installation

Placement

CAUTION

Before moving the unit into position, secure the door

closed and protect any ﬁnished ﬂooring.

WARNING

When positioning the appliance, ensure the supply

cord is not trapped or damaged.

Use an appliance dolly to move the unit near the opening.

If the unit has been on its back or side, it must stand

upright for a minimum of 24 hours before connecting

power.

Plug the power cord into the grounded outlet. For model

DEU2450CI, insert the water supply line into the hole on

the back of the unit. Refer to the illustration below. Pull the

excess water line forward as the unit is slid into the open-

ing. Verify the anti-tip bracket is properly engaged.

BACK OF UNIT

HOLE FOR

WATER LINE

Water line (model DEU2450CI)

subzero.com | 9

Water Line

MODEL DEU2450CI

Under the unit, ⁄" plastic tubing is connected to the unit

with a preassembled ⁄" compression connection. The

water line ﬁtting connection kit, provided with the unit,

contains a ⁄" compression union ﬁtting for connection to

the household water line.

Purge the water line prior to ﬁnal connection to the unit.

This will remove any debris that may be present in the

tubing from installing the new water line. Connect the

plastic tubing from the unit to the house water supply line

with the ﬁtting connection kit provided. Refer to the

illustration below. Check all water line ﬁttings for leaks.

IMPORTANT NOTE: Water lines cannot be exposed to

freezing temperatures.

WARNING

Connect to potable water supply only.

WATER LINE

CONNECTION

Water line connection

Installation

Alignment

ANCHORING

CAUTION

If using a power drill to predrill holes or install

screws, verify the drill chuck does not contact the

units face frame.

Adjust the depth of the unit to ﬁt ﬂush with the surround-

ing cabinetry. Allow for panel thickness. Once aligned,

verify the door opens properly, then install screws in each

bracket.

WARNING

To avoid a hazard due to instability of the appliance,

it must be ﬁxed in accordance with the instructions.

Anchoring

10 | Sub-Zero Customer Care 800.222.7820

Custom Panel

A custom door panel and handle hardware must be

installed.

A ⁄"

(16) minimum to ⁄" (19) maximum thick panel is

required. The panel cannot exceed the maximum panel

weight indicated in the chart below. The depth of each

model is 23⁄"

(587). Allow for panel thickness when plan-

ning the ﬁnished opening depth.

Minimum ⁄"

(3) reveals are required.

PANEL WEIGHT MAX

24" Model 22 lb (10 kg)

Finish all sides of the custom panel. They will be visible

when the door is open.

A D-style handle is recommended. Locate the door handle

near the edge of the panel opposite the hinge and cen-

tered top to bottom. Stainless steel tubular and pro handles

are avail able through an authorized Sub-Zero dealer. For

local dealer information, visit the ﬁnd a showroom section

of our website, subzero.com.

Door Panel

Stainless Steel Panel

Stainless steel panels are available through an authorized

Sub-Zero dealer. Stainless steel panels include a stainless

steel kickplate cover. The outdoor model requires the use

of a Sub-Zero stainless steel outdoor accessory panel. For

local dealer information, visit the ﬁnd a showroom section

of our website, subzero.com.

Minimum ⁄"

(3) reveals are required.

subzero.com | 11

Custom Panel

TOE KICK CLEARANCE

The height of the toe kick area can extend beyond the

typical toe kick height, provided it does not exceed the

dimensions in the illustration below. For questions

regarding the installation, call Sub-Zero Customer Care

at 800-222-7820.

Door Panel

MAXIMUM DOOR OPENING

As the panel width and/or depth increases, so does the

potential for panel interference. Interference may be

minimized by using the 90° door stop.

3

/8" (10)

DOOR CLOSED

3

/4" (19) PANEL

1

/

8

"

(3) REVEAL

ADJACENT

CABINETRY

DOOR

OPEN

90°

DOOR OPEN

MAXIMUM 115°

Maximum door opening (top view)

DOOR

PANEL

HINGE

23

1

/

8

"

(587)

TO BACK OF UNIT

2" (51)

TO

4

1

/2" (114)

FROM

FLOOR

3

1

/2" (89)

MAX DEPTH

1

/8" (29)

KICKPLATE

ADJUSTMENT

34

1

/2" (876)

TYPICAL

PRODUCT

HEIGHT

DECORATIVE KICKPLATE

CANNOT EXTEND

BEYOND THIS

POINT

3

/8" (86)*

DECORATIVE

KICKPLATE

HEIGHT

*Not included. Dimension will vary as the product height increases or decreases

from the typical product height.

Toe kick clearance (side view)

12 | Sub-Zero Customer Care 800.222.7820

Panel Installation

DOOR PANEL INSTALLATION

Typical panel dimensions are based on an 34⁄"

(876) ﬁn-

ished height with ⁄"

(3) reveals. Placement of the template

must be adjusted for panels exceeding the typical dimen-

sions.

Place the panel face down on a protected work surface.

Position the template ﬂush with the top and sides of the

panel. Verify the correct side of the template is being used,

then mark and drill holes. Refer to the illustration below.

Use a Torx drive to partially insert a #8 x ⁄" screw into the

second hole from the top on each side of the panel. The

screws should be approximately ⁄"

(4) proud of the panel

and will support the weight of the panel during installation.

Align the support screws on the back of the panel with the

slotted holes on both door mounting brackets. Refer to

the illustration below. Opening the door slightly may help

with alignment. Once the panel is supported by the screws,

partially insert a #8 x ⁄" screw into the second hole from

the bottom on each side of the panel, but do not tighten.

CAUTION

As reveals between cabinetry and the unit decrease,

severe ﬁnger pinching can occur while the door is

closing.

TOP OF DOOR PANEL

LEFT SIDE DOOR PANEL

RIGHT SIDE DOOR PANEL

Door panel template

BACK OF PANEL

Door panel mounting

subzero.com | 13

Panel Installation

DOOR PANEL ADJUSTMENT

Close the door. Make any necessary adjustments to align

the panel and reveals.

For side-to-side adjustment, move the panel side to side,

then install and tighten all mounting screws.

For up-and-down and in-and-out adjustments, slightly

loosen the bracket screws. Depending on the level of

adjustment required, it may be helpful to loosen all of the

bracket screws which will allow for maximum adjustment.

Once the bracket screws are loosened, use a wrench to

rotate the cams to make adjustments. After the adjust-

ments have been made, tighten all bracket screws. Refer to

the illustrations below.

Panel Installation

BRACKET

SCREWS

IN-AND-OUT

CAM

BRACKET

SCREWS

UP-AND-DOWN

CAM

In-and-out adjustment

Up-and-down adjustment

14 | Sub-Zero Customer Care 800.222.7820

KICKPLATE INSTALLATION

The kickplate must be removable for service. The ﬂoor

cannot interfere with removal. Finger-tighten the adjust-

ment bracket nuts. Refer to the illustration below. Make

in-and-out adjustments, then wrench-tighten the bracket

nuts. Install the kickplate with the provided screws.

A decorative kickplate can be attached to the factory-

installed kickplate. The three rows of vented louvers

cannot be covered. A decorative kickplate cannot be

attached to the outdoor model.

To install a decorative kickplate, remove the paper backing

from the magnets and attach the decorative kickplate to

the magnets. The magnets allow the decorative kickplate

to be removed if necessary.

Completion

DOOR TRIM INSTALLATION

After the door panel has been adjusted, install the deco-

rative side trim to the door. To install, start at the top

and align the trim with the front and rear ﬂanges on the

bracket, then snap into place by pushing the trim toward

the back of the panel. Once the top is secure, continue the

installation downward until the remaining trim is com-

pletely secure. Refer to the illustration below.

SIDE TRIM INSTALLATION

Install the decorative trim strip to the handle side of the

unit. The side trim snaps over the brackets attached to the

handle side of the unit. Refer to the illustration below.

Installation

Door side trim

Unit side trim

KICKPLATE

ADJUSTMENT

SCREW

MAGNET

Kickplate adjustment

Kickplate installation

subzero.com | 15

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowﬂake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.

Installation

Completion

WARNING

Follow all city and state laws when storing, recycling,

or discarding unused refrigerators and freezers.

2 | Atención al cliente de Sub-Zero 800.222.7820

Refrigeración bajo mostrador de la Serie de Diseño

Contenido

3 Refrigeración bajo mostrador de la Serie de Diseño

4 Dimensiones de abertura

5 Requisitos eléctricos

6 Requisitos de plomería

6 Preparación

7 Soporte antivuelco

7 Tope para puerta a 90°

8 Colocación

8 Alineación

9 Línea de agua

10 Panel de la puerta

12 Instalación del panel

14 Finalización

Las características y especiﬁcaciones están sujetas a

cambios sin previo aviso. Visite subzero.com/specs para

obtener la información más actualizada.

Aviso importante

Para garantizar que este producto se instale y opere de

la forma más segura y eﬁciente posible, tome nota de los

siguientes tipos de información resaltada en este manual:

AVISO IMPORTANTE señala la información que es

especialmente importante.

PRECAUCIÓN indica una situación en la que se pueden

sufrir heridas leves o provocar daños al producto si no se

siguen las instrucciones.

ADVERTENCIA indica peligro de que se produzcan heridas

graves o incluso la muerte si no se siguen las precauciones.

AVISO IMPORTANTE: En toda esta guía, las dimensiones

entre paréntesis son milímetros, a menos que se

especiﬁque lo contrario.

AVISO IMPORTANTE: Guarde estas instrucciones para el

inspector eléctrico local.

subzero.com | 3

Refrigeración bajo mostrador de la Serie de Diseño

Información del producto

La información importante del producto, incluidos el

modelo y el número de serie de la unidad, se encuentra

en la placa de datos del producto. La placa de datos

se encuentra dentro del gabinete, en el área superior

izquierda de la unidad. Consulte la siguiente ilustración.

Si necesita servicio, póngase en contacto con el centro

de servicio autorizado de Sub-Zero y tenga a la mano el

modelo y número de serie de la máquina. Para obtener

los datos del centro de servicio autorizado de Sub-Zero

más cercano o si tiene preguntas acerca de la instalación,

visite la sección de soporte técnico en nuestra página de

Internet subzero.com o llame a la línea de atención al

cliente de Sub-Zero al 800-222-7820.

PLACA DE DATOS

Ubicación de la placa de datos

4 | Atención al cliente de Sub-Zero 800.222.7820

La profundidad de cada modelo es de 23⁄" (587). Para

determinar la profundidad de la abertura ya con acabados,

considere el grosor del panel. Se necesita un tubo de

retorno de 3⁄"

(89) con acabados en todos los lados de la

abertura. Los gabinetes con marco necesitan material de

relleno de acabado detrás del marco frontal para lograr

una instalación adecuada. Consulte la ilustración.

INSTALACIÓN DOBLE

Si se instalan dos unidades lado a lado, puede ser

necesario un kit de instalación doble. Las instalaciones

sin una tira de relleno personalizada requieren un kit de

instalación doble. Si el uso de un kit de instalación doble

no está especiﬁcado, se recomienda utilizar una tira de

relleno de 2"

(51) entre las unidades. Las instalaciones

dobles sin una tira de relleno solo se pueden realizar

cuando se utilizan dos unidades con bisagras opuestas.

Revise las siguientes ilustraciones.

Los kits de instalación doble están disponibles a través

de un distribuidor autorizado de Sub-Zero. Para obtener

más información acerca de los distribuidores locales,

consulte la sección “encuentre una sala de exhibición” en

nuestra página web subzero.com. Para preguntas sobre

la instalación, comuníquese con la línea de atención al

cliente de Sub-Zero al 800-222-7820.

ANCHURA DE ABERTURA DOBLE W

Dos modelos de 24" 48" (1219)

Se requiere kit de instalación doble.

Preparación del sitio

Dimensiones de abertura

MODELOS BAJO MOSTRADOR

ANCHO DE LA

ABERTURA

W

ALTURA DE LA

ABERTURA

H

VISTA SUPERIOR

VIST

A LATERAL VISTA FRONTAL

NOTA: Los tubos de retorno de

3

1

/2" (89) con acabados se podrán ver y se deben

ter

minar para que se ajusten a los gabinetes.

TÍPICO

DE

3

/4" (19)

GABINETE

CON MARCO

W

RELLENO

TUBO DE

RETORNO

DE

3

1

/2" (89)

CON ACABADOS

GABINETES

SIN MARCO

W

TÍPICO

DE

3

/4" (19)

TUBO DE

RETORNO

DE

3

1

/2" (89)

CON ACABADOS

PROFUNDIDAD DE

LA ABERTURA

DE

24" (610)

SIN TIRA DE RELLENO

TIRA DE RELLENO

Bisagras opuestas

Bisagras en el mismo lado

DIMENSIONES DE ABERTURA W H

Modelo de 24" 24" (610) 34⁄" (876)

subzero.com | 5

Requisitos eléctricos

La instalación debe cumplir con todos los códigos

eléctricos vigentes.

El suministro eléctrico debe colocarse dentro del área

sombreada que se muestra en la siguiente ilustración.

Se necesita un circuito independiente que le suministre

electricidad únicamente a este electrodoméstico.

AVISO IMPORTANTE: Para los modelos internos, no es

recomendable utilizar un interruptor circuito de fallos de

conexión a tierra (Ground Fault Circuit Interrupter, GFCI),

ya que puede interrumpir el funcionamiento de la unidad.

Para los modelos externos, es necesario instalar un

interruptor de circuito de fallos de conexión a tierra (GFCI)

para reducir el riesgo de descarga eléctrica.

El tomacorriente eléctrico debe colocarse de tal forma que

la clavija con conexión a tierra quede a la derecha de las

aspas más delgadas.

1

/4" (6)

4"

(102)

3"

(76)

9"

(229)

SUELO

LADO DERECHO

DE LA ABERTURA

Ubicación del suministro

eléctrico

PRECAUCIÓN

Un electricista caliﬁcado debe revisar el

tomacorriente para asegurarse de que la conexión

del cableado se haya realizado con la polaridad

correcta. Compruebe que el tomacorriente esté

debidamente conectado a tierra.

ADVERTENCIA

Si el cable de alimentación está dañado, debe ser

reemplazado por el fabricante, su agente de servicio

o personas caliﬁcadas de manera similar para evitar

un peligro.

ADVERTENCIA

No coloque múltiples tomas de corriente, enchufe

múltiple o suministros eléctricos portátiles en la

parte posterior del electrodoméstico.

ADVERTENCIA

No use un cable de extensión, adaptador de dos

clavijas ni retire la clavija con conexión a tierra del

cable de corriente.

REQUISITOS ELÉCTRICOS

Suministro eléctrico 115 V CA, 60 Hz

Servicio Circuito dedicado de 15 amperes

Receptáculo Conexión a tierra de 3 clavijas

Preparación del sitio

6 | Atención al cliente de Sub-Zero 800.222.7820

Requisitos de plomería

MODELO DEU2450CI

La instalación debe cumplir con todos los códigos de

plomería vigentes.

Para facilitar la instalación, empotre en la pared la

válvula de cierre de agua o colóquela en un gabinete

adjunto. Localice la línea de suministro de agua en la

zona sombreada que se muestra en la ilustración a

continuación. Conecte la línea de suministro de agua al

suministro de la casa con una válvula de cierre de fácil

acceso. No utilice válvulas autoperforantes.

Se requiere un ﬁltro en línea cuando las condiciones del

agua tienen un alto contenido de sedimentos.

Se puede utilizar un sistema de ósmosis inversa siempre

y cuando la presión del agua que llegue a la unidad se

mantenga de forma constante entre 35 y 120 psi (de 2.4

a 8.3 bares) en todo momento. No es recomendable usar

tuberías de cobre para esta aplicación.

REQUISITOS DE PLOMERÍA

Tuberías de suministro de agua Tubería de cobre, trenzada de

acero inoxidable o PEX de ⁄"

de diámetro exterior

Presión del agua De 35 a 120 psi (de 2.8 a

8.3bares)

Tubería de exceso de agua para

la conexión

5' (1.5 m)

Preparación

Desembale la unidad e inspeccione si tiene algún daño.

Retire y recicle los materiales de embalaje. No deseche el

zócalo, el soporte antivuelco ni las piezas de montaje.

Para quitar el zócalo extraiga los dos tornillos para

montaje. Consulte la siguiente ilustración.

TORNILLO

Extracción del zócalo

4"

(102)

3"

(76)

9"

(229)

LADO IZQUIERDO

DE LA ABERTURA

EL ÁREA SE EXTIENDE

1

/2" (13)

EN EL SUELO

Ubicación del suministro de

agua

Preparación del sitio

La page charge ...

Sub-Zero 5310890 Guide d'installation

Ce manuel convient également à

Sub-Zero 5310890 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents