Indesit FRI 886.1 MT Mode d'emploi

Marque: Indesit

Modèle: FRI 886.1 MT

Catégorie: Fours

Taper: Mode d'emploi

FRI 886.1 MT

English

Operating Instructions

OVEN

Français

Mode d’emploi

FOUR

Contents

Operating Instructions,1

Warnings,2

Assistance,4

Description of the appliance,5

Description of the appliance,6

Installation,7

Start-up and use,9

Modes,10

Precautions and tips,14

Maintenance and care,15

Troubleshooting,16

Sommaire

Mode d’emploi,1

Avertissements,2

Assistance,4

Description de l’appareil,5

Description de l’appareil,6

Installation,17

Mise en marche et utilisation,19

Programmes,20

Précautions et conseils,24

Nettoyage et entretien,25

Anomalies et remèdes,26

Warnings

WARNING: The appliance and its accessible parts

become hot during use. Care should be taken to

avoid touching heating elements. Children less than 8

years of age shall be kept away unless continuously

supervised. This appliance can be used by children

aged from 8 years and above and persons with

reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been

given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards

involved. Children shall not play with the appliance.

Cleaning and user maintenance shall not be made

by children without supervision.

Do not use harsh abrasive cleaners or sharp metal

scrapers to clean the oven door glass since they can

scratch the surface, which may result in shattering of

the glass.

“Before initiating the automatic cleaning cycle:

• clean the oven door;

• remove large or coarse food residues from the

inside of the oven using a damp sponge. Do not

use detergents;

• remove all accessories and the sliding rack kit

(where present);

• do not place tea towels”

Keep children away from the appliance during the

automatic cleaning cycle as surfaces may become

very hot.

Never use steam cleaners or pressure cleaners on

the appliance.

WARNING: Ensure that the appliance is switched

off before replacing the lamp to avoid the possibility

of electric shock.

! When you place the rack inside, make sure that the

stop is directed upwards and in the back of the cavity.

Avertissements

ATTENTION : Cet appareil ainsi que ses parties

accessibles deviennent très chauds pendant leur

fonctionnement. Il faut faire attention à ne pas toucher

les éléments chauffants. Ne pas faire approcher les

enfants de moins de 8 ans à moins qu’ils ne soient

sous surveillance constante. Le présent appareil peut

être utilisé par des enfants de plus de 8 ans et par

des personnes présentant des capacités physiques,

sensorielles ou mentales réduites ou n’ayant pas

l’expérience ou les connaissances indispensables,

à condition qu’ils soient sous bonne surveillance ou

qu’ils aient reçu les instructions nécessaires pour une

utilisation de l’appareil en toute sécurité et à condition

qu’ils se rendent compte des dangers encourus. Les

enfants ne doivent pas jouer avec l’appareil. Les

opérations de nettoyage et d’entretien ne doivent

pas être effectuées par des enfants non surveillés.

Ne pas utiliser de produits abrasifs ni de spatules

métalliques coupantes pour nettoyer la porte du four

en verre, sous peine d’éraer la surface et de briser

le verre.

Avant d’activer la fonction de nettoyage automatique :

• nettoyer la porte du four

• enlever avec une éponge humide les résidus les

plus gros. Ne pas utiliser de détergents ;

• sortir tous les accessoires ainsi que le kit éventuel

de glissières coulissantes ;

• ne pas placer de torchons ou de maniques sur la

poignée du four.

Lors du nettoyage automatique, les surfaces peuvent

devenir chaudes, c’est pourquoi il convient d’éloigner

les jeunes enfants.

Ne jamais nettoyer l’appareil avec des nettoyeurs

vapeur ou haute pression.

ATTENTION : s’assurer que l’appareil est éteint

avant de procéder au remplacement de l’ampoule,

an d’éviter tout risque d’électrocution.

! Lors de l’introduction de la grille, s’assurer que

l’arrêt est bien tourné vers le haut et se trouve dans

la partie arrière de l’enceinte.

Assistance

Warning:

The appliance is tted with an automatic diagnostic system which detects any

malfunctions. Malfunctions are signalled through messages of the following

type: “F—” followed by numbers.

Call for technical assistance in the event of a malfunction.

Before calling for Assistance:

• Check whether you can x the problem yourself.

• Restart the programme to check whether the malfunction has

disappeared.

• If it has not, contact the Authorised Technical Assistance Service.

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The message shown on the TEMPERATURE display.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the data plate located

on the appliance.

Assistance

Attention :

L’appareil dispose d’un système d’autotest qui permet de détecter toute

anomalie de fonctionnement. Ces anomalies sont afchées sous la forme:

«F—» suivi de chiffres.

Contacter alors un service d’assistance technique.

Avant d’appeler le service de dépannage :

• Vérier s’il est possible de résoudre le problème soi-même ;

• Redémarrer le programme pour contrôler si le problème a été résolu;

• Si ce n’est pas le cas, contacter le service d’Assistance technique agréé.

! Ne jamais faire appel à des techniciens non agréés.

Indiquer :

• le type d’anomalie;

• le code erreur afché sur l’écran TEMPERATURE

• le modèle de l’appareil (Mod.);

• son numéro de série (S/N).

Ces informations gurent sur la plaque signalétique apposée sur l’appareil

Description of the appliance

Overall view

1 POSITION 1

2 POSITION 2

3 POSITION 3

4 POSITION 4

5 POSITION 5

6 GUIDES for the sliding racks

7 DRIPPING PAN

8 GRILL

9 Control panel

9 6

Description de l’appareil

Vue d’ensemble

1 NIVEAU 1

2 NIVEAU 2

3 NIVEAU 3

4 NIVEAU 4

5 NIVEAU 5

6 GLISSIERES de coulissement

7 Support LECHEFRITE

8 Support GRILLE

9 Tableau de bord

Description of the appliance

Control panel

1. MANUAL COOKING MODE Icons

2. PYROLYSIS selector

3. TEMPERATURE display

4. TEMPERATURE icon

5. DURATION icon

6. TIME display

7. END OF COOKING Icon

8. CONTROL PANEL LOCK icon

9. START / STOP

10. LIGHT icon

11. CLOCK icon

12. MINUTE MINDER Icon

13. TIME / TEMPERATURE ADJUSTMENT Icons

14. PREHEATING / RESIDUAL HEAT icons

15. DOOR LOCK indicator

16. AUTOMATIC/ECO COOKING MODE icons

17. CONTROL PANEL POWER BUTTON

Description de l’appareil

Tableau de bord

1. Icônes PROGRAMMES MANUELS

2. Sélection PYROLYSE

3. Afcheur TEMPERATURE

4. Icône TEMPÉRATURE

5. Icône DURÉE

6. Afcheur TEMPS

7. Icône FIN CUISSON

8. Icône VERROUILLAGE COMMANDES

9. DÉPART / ARRÊT

10. Icône ECLAIRAGE

11. Icône HORLOGE

12. Icône MINUTEUR

13. Icônes RÉGLAGE TEMPS / TEMPÉRATURE

14. Icône PRÉCHAUFFAGE / CHALEUR RÉSIDUELLE

15. Voyant PORTE VERROUILLÉE

16. Icônes PROGRAMMES AUTOMATIQUES / ECO

17. ALLUMAGE PANNEAU

Installation

! Please keep this instruction booklet in a safe place for future reference. If

the appliance is sold, given away or moved, please make sure the booklet is

also passed on to the new owners so that they may benet from the advice

contained within it.

! Please read this instruction manual carefully: it contains important information

concerning the safe operation, installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it should be disposed

of in accordance with local separated waste collection standards (see

Precautions and tips).

! The appliance must be installed by a qualied professional in accordance

with the instructions provided. Incorrect installation may damage property or

cause harm to people or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance operates properly:

• The panels adjacent to the oven must be made of heat-resistant material.

• Cabinets with a veneer exterior must be assembled with glues which can

withstand temperatures of up to 100°C.

• To install the oven under the counter (see diagram) or in a kitchen unit,

the cabinet must have the following dimensions:

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

560 mm.

547 mm. min.

! The appliance must not come into contact with electrical parts once it has

been installed. The indications for consumption given on the data plate have

been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the cabinet must be

removed. It is advisable to install the oven so that it rests on two strips of

wood, or on a completely at surface with an opening of at least 45 x 560

mm (see diagrams).

560 mm.

45 mm.

Centring and xing

Position the 4 tabs on the side of the oven so that they are lined up with the

4 holes on the outer frame. Adjust the tabs according to the thickness of the

cabinet side panel, as shown below:

20 mm thick: take off the removable part of the

tab (see diagram).;

18 mm thick: use the rst groove, which has

already been set in the factory (see diagram).

16 mm thick: use the second groove (see

diagram).

Secure the appliance to the cabinet by opening the oven door and putting 4

screws into the 4 holes on the outer frame.

! All parts which ensure the safe operation of the appliance must not be

removable without the aid of a tool.

Electrical connection

Ovens equipped with a three-pole power supply cable are designed to operate

with alternating current at the voltage and frequency indicated on the data

plate located on the appliance (see below).

Fitting the power supply cable

1. Open the terminal board by inserting

a screwdriver into the side tabs of the

cover. Use the screwdriver as a lever

by pushing it down to open the cover

(see diagram).

2. Install the power supply cable by

loosening the cable clamp screw

and the three wire contact screws

L-N- .

Connect the wires to the corresponding

terminals: the Blue wire to the terminal

marked (N), the Brown wire to the

terminal marked (L) and the Yellow/

Green wire to the terminal marked

(see diagram).

3. Secure the cable by fastening the

clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load indicated on the data

plate (see table).

The appliance must be directly connected to the mains using an omnipolar

switch with a minimum contact opening of 3 mm installed between the

appliance and the mains. The switch must be suitable for the charge indicated

and must comply with current electrical regulations (the earthing wire must not

be interrupted by the switch). The supply cable must be positioned so that it

does not come into contact with temperatures higher than 50°C at any point

(the back panel of the oven, for example).

! The installer must ensure that the correct electrical connection has been

performed and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that

• The appliance is earthed and the plug is compliant with the law.

• The socket can withstand the maximum power of the appliance, which is

indicated on the data plate.

• The voltage is in the range between the values indicated on the data plate.

• The socket is compatible with the plug of the appliance. If the socket is

incompatible with the plug, ask an authorised technician to replace it. Do

not use extension cords or multiple sockets.

! Once the appliance has been installed, the power supply cable and the

electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by authorised technicians

only (see Assistance).

! The manufacturer declines any liability should these safety measures

not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 32,4 cm

depth 41.5 cm

Volume*

59 l

Dimensions**

width 45.5 cm

height 32,4 cm

depth 41.5 cm

Volume**

62 l

Electrical

connections

voltage: 220-240V~ 50Hz

(see data plate) maximum power

absorbed 2800 W

* Only for models with drawn rails.

** Only for models with wire rails.

Energy

Label e

Ecodesign

Declared energy consumption for

Forced convection Class

mode: Baking

This appliance conforms to the

following European Economic

Community directives:

- 2006/95/EC dated 12/12/06 (Low

Voltage) and subsequent amendments.

- 2004/108/EC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent amendments.

- 93/68/EEC dated 22/07/93 and

subsequent amendments.

- 2012/19/EU and subsequent

amendments.

- 1275/2008 standby/off mode.

EU Directive no 65/2014

supplementing Directive 2010/30/EU.

EU Regulation no 66/2014

implementing Directive 2009/125/EC.

Standard EN 60350-1

Standard EN 50564

Start-up and use

WARNING! The oven is provided

with a stop system to extract the

racks and prevent them from

coming out of the oven (1).

As shown in the drawing, to extract

them completely, simply lift the

racks, holding them on the front

part, and pull (2).

! The rst time you use your appliance, heat the empty oven with its door closed

at its maximum temperature for at least half an hour. Make sure that the room

is well ventilated before switching the oven off and opening the oven door. The

appliance may emit a slightly unpleasant odour caused by protective substances

used during the manufacturing process burning away.

! To make the setting process easier, press and hold the “

” and “ ” buttons

to scroll through the numbers on the display rapidly.

! Each setting will automatically be stored in the appliance memory after 10

seconds.

! The touch controls cannot be activated if the user is wearing gloves.

! In order to optimise the cooking performance, when starting the selected

function, product settings will be applied that could cause a delayed start of

the fan and heating elements.

Control panel lock

! The control panel can be locked while the oven is off, once cooking has

started or nished and during programming.

To lock the oven controls, press and hold the

button for at least 2

seconds. A buzzer will sound and the TEMPERATURE display shows the

key symbol “O—n”. The

icon will light up to indicate lock activation.

To deactivate the lock, press and hold the button again for at least 2

seconds.

Setting the clock

! The clock can only be set when the oven is switched off. If the oven is in

standby mode, pressing the

button once will display the current time

setting. Press it again to set the time.

After connection to the power supply network or after a blackout, the

button and the digits on the TIME display will ash for 10 seconds.

To set the clock:

1. Press the

button.

2. Adjust the hour gure using the “ ” and “ ” buttons.

3. Once you have reached the correct hour value, press the

button.

4. Repeat the above process to set the minutes.

If a blackout occurs, it will be necessary to reset the clock. If the

icon

ashes on the display, this indicates that the clock has not been set correctly.

Setting the minute minder

! The minute minder may be set regardless of whether the oven is switched

on or off. It does not switch the oven on or off.

When the set time has elapsed, the timer emits a buzzer that will automatically

stop after 30 seconds or when any active button on the control panel is

pressed.

To adjust the timer proceed as follows:

1. Press button

2. Set the desired time using buttons “ ” and “ ”.

3. Once you have reached the desired value, press the

button again.

The lit

symbol will remind you that the minute minder is on.

To cancel the minute minder, press the

button and use the “ ” and “ ”

buttons to set the time to 00:00. Press button

again.

The

icon will switch off to indicate that the minute minder has been disabled.

Starting the oven

1. Switch the control panel on by pressing the button. The appliance

buzzer sounds three times (ascending) and all buttons light up in sequence.

2. Press the button corresponding to the desired cooking mode. The

TEMPERATURE display shows:

- the temperature associated with the mode, if programming manually;

- “Auto”, if programming is automatic.

The TIME display shows:

- the current time, if programming manually;

- the duration, if programming is automatic.

3. Press the

button to begin cooking.

4. The oven will begin its preheating phase, the preheating indicators will light

up as the temperature rises.

5. When the preheating process has nished, a buzzer sounds and all the

preheating indicator lights show that this stage has been completed: the food

can then be placed in the oven.

6. During cooking it is always possible to:

- change the temperature by pressing the

button, followed by the “ ”

and “

” buttons (manual modes only);

- set the duration of a cooking mode (see Cooking Modes);

- press the

button to stop cooking. In this case the appliance stores the

temperature modied previously in its memory (manual modes only);

- switch off the oven by pressing the

button for 3 seconds.

7. If a blackout occurs while the oven is already in operation, an automatic

system within the appliance will reactivate the cooking mode from the point at

which it was interrupted, provided that the temperature has not dropped below

a certain level. Programmed cooking modes which have not yet started will

not be restored and must be reprogrammed (for example: a cooking mode

has been programmed to start at 20:30. At 19:30 a blackout occurs. When the

power supply is restored, the mode will have to be reprogrammed).

! There is no preheating stage for the GRILL mode.

! Never put objects directly on the bottom of the oven; this will prevent the

enamel coating from being damaged.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the oven, a cooling fan

blows a stream of air between the control panel and the oven door, as well

as towards the bottom of the oven door.

At the beginning of the PYROLISIS mode, the cooling fan operates at low

speed.

! Once cooking has been completed, the cooling fan continues to operate

until the oven has cooled down sufciently.

Oven light

The light comes on when the oven door is opened or when a cooking mode

starts.

The

button can be used to switch on the light at any time.

Residual heat indicators

The appliance is tted with a residual heat indicator. When the oven is off,

the “residual heat” bar on the display lights up to indicate high temperatures

inside the oven cavity. The individual segments of the bar switch off one by

one as the temperature inside the oven falls.

Demo mode

The oven can operate in the DEMO mode: all heating elements are

deactivated, and the controls remain operative.

To activate DEMO mode, press and release button

, then buttons “ ” and

“

” simultaneously for 6 seconds, and then press and release button .

A buzzer sounds and the TEMPERATURE display shows “dEon”. To

deactivate DEMO mode, when the oven is off press and hold button

and

button “

” simultaneously for 3 seconds. A buzzer sounds and the “dEoF”

message disappears from the display.

Restoring the factory settings

The oven factory settings can be restored to reset all selections made by

the user (clock and customised durations). To carry out a reset, switch off

the oven, then press and hold the button corresponding to the rst manual

cooking mode (top left) and the

button simultaneously for 6 seconds.

Once the restore procedure is complete, a buzzer will sound. The rst time

the

button is pressed, the oven will behave as if it is being switched

on for the rst time.

Standby

This product complies with the requirements of the latest European Directive

on the limitation of power consumption of the standby mode. If no buttons

are pressed for 30 minutes and the control panel/door lock has not been

activated, the appliance automatically reverts to standby mode. Standby mode

is indicated by the high luminosity “Clock button” light. As soon as interaction

with the machine resumes, the system’s operating mode is restored.

Modes

! Every time the oven is switched on, it suggests the rst manual cooking mode.

Manual cooking modes

! All cooking modes have a default cooking temperature which may be

adjusted manually to a value between 30°C and 250°C as desired (300°C

for GRILL mode). Any temperature adjustments will be stored in the

appliance memory and suggested again the next time this mode is used.

If the selected temperature is lower than the temperature inside the oven,

the text “Hot” appears on the TEMPERATURE display. However, it will still

be possible to start cooking.

MULTILEVEL mode

All heating elements and the fan are activated. Since the heat remains constant

throughout the oven, the air cooks and browns food in a uniform manner. A

maximum of two racks may be used at the same time.

BARBECUE mode

The top heating element and the rotisserie spit (where present) are activated.

The high and direct temperature of the grill is recommended for food which

requires a high surface temperature. Always cook in this mode with the oven

door closed (see “Practical cooking advice”).

TURNSPIT mode

The function is ideal for turnspit cooking. Always cook in this mode with the

oven door closed.

FAN GRILLING mode

The top heating element and the rotisserie spit (where present) are activated

and the fan begins to operate. During part of the cycle the circular heating

element is also activated. This combination of features increases the

effectiveness of the unidirectional thermal radiation provided by the heating

elements through the forced circulation of the air throughout the oven.

This helps prevent food from burning on the surface and allows the heat to

penetrate right into the food. Always cook in this mode with the oven door

closed (see “Practical cooking advice”).

PIZZA modes

The top and circular heating elements switch on and the fan begins to operate.

This combination heats the oven rapidly. If you use more than one rack at a

time, switch the position of the dishes halfway through the cooking process.

BAKING mode

The rear heating element and the fan are switched on, thus guaranteeing the

distribution of heat in a delicate and uniform manner throughout the entire oven.

This mode is ideal for baking temperature sensitive foods (such as cakes,

which need to rise).

Rotisserie spit

To operate the rotisserie function

(see diagram) proceed as follows:

1. Place the dripping pan in position

2. Place the rotisserie support in

position 3 and insert the spit in the

hole provided on the back panel of

the oven.

3. Start the rotisserie function by

selecting the

modes;

! When mode is on, the rotisserie will stop if the door is opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set values, guaranteeing

a perfect result every time - automatically. These values are set using the

C.O.P.® (Programmed Optimal Cooking) system. The cooking cycle stops

automatically and the oven indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not.

The cooking duration can be customised according to personal taste by

modifying the relevant value - before cooking begins - by ±5/20 minutes

depending on the selected programme. The duration can however be

modied even once cooking has begun. If the value is modied before the

programme begins, it is stored in the memory and suggested again by the

appliance when the programme is next used. If the temperature inside the

oven is higher than the suggested value for the selected mode, the text “Hot”

appears on the TEMPERATURE display and it will not be possible to begin

cooking; wait for the oven to cool.

! When the cooking stage has been reached, the oven buzzer sounds.

! Do not open the oven door as this will disrupt the cooking time and

temperature.

ROAST mode

Use this function to cook beef, veal, pork, chicken and lamb. Place the

food inside the oven while it is still cold. The dish may also be placed in a

preheated oven.

CHICKEN mode

This function is ideal for cooking chicken (whole or in pieces). Place the

food inside the oven while it is still cold. The dish may also be placed in a

preheated oven.

BAKED CAKES mode

This function is ideal for cooking desserts which are made using natural yeast,

baking powder and desserts which contain no yeast. Place the dish in the

oven while it is still cold. The dish may also be placed in a preheated oven.

TARTS mode

This function is ideal for all tart recipes (which normally need to be heated

well from underneath). Place the food inside the oven while it is still cold.

The dish may also be placed in a preheated oven.

PASTRIES mode

This function is ideal for baked desserts (made using natural yeast). Place

the food inside the oven while it is still cold; the dish may also be placed in a

preheated oven if desired.

BREAD mode

Use this function to bake bread. To obtain the best results, we recommend

that you carefully observe the instructions below:

• follow the recipe;

• do not exceed the maximum weight of the dripping pan;

• remember to pour 50 g (0,5 dl) of cold water into the baking tray in

position 5.

• The dough must be left to rise at room temperature for 1 – 1 ½ hours

(depending on the room temperature) or until the dough has doubled in

size.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and lower levels

Recipe for 1000 g of dough: 600 g our, 360 g water, 11g salt, 25 g fresh yeast

(or 2 sachets of powder yeast)

Method:

• Mix the our and salt in a large bowl.

• Dilute the yeast in lukewarm water (approximately 35 degrees).

• Make a small well in the mound of our.

• Pour in the water and yeast mixture.

• Knead the dough by stretching and folding it over itself with the palm of

your hand for 10 minutes until it has a uniform consistency and is not too

sticky.

• Form the dough into a ball shape, place it in a large bowl and cover it with

transparent plastic wrap to prevent the surface of the dough from drying

out. Select the manual LOW TEMPERATURE function on the oven and

set the temperature to 40°C. Place the bowl inside and leave the dough

to rise for approximately 1 hour (the dough should double in volume).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan, on a sheet of baking paper.

• Dust the loaves with our.

• Make incisions on the loaves.

• Place the food inside the oven while it is still cold.

• Start the

BREAD cooking mode.

• Once baked, leave the loaves on one of the grill racks until they have

cooled completely.

Programming cooking

! A cooking mode must be selected before programming can take place.

! Once a cooking mode has been selected, the

button is activated; it will

then be possible to program a duration. The button is only activated after

a duration has been set; it will then be possible to program a delayed start.

Programming the duration

1. Press the

button; the button and the numbers on the TIME

display will ash.

2. Set the duration by pressing buttons “ ” and “ ”.

3. Once you have reached the desired duration, press the

button again.

4. Press the

button to begin cooking.

5. When cooking has nished, “END” appears on the TEMPERATURE display

and a buzzer sounds.

• For example: it is 9:00 a.m. and a duration of 1 hour and 15 minutes is

programmed. The programme will stop automatically at 10:15 a.m.

Programming delayed cooking

! A cooking duration must be set before the cooking end time can be scheduled.

! For the delayed programming to work properly, the clock should be set to

the correct time.

1. Press the

button and repeat steps 1 to 3 as described for the duration

setting.

2. Then press the

button and set the end time using the “ ” and “

” buttons.

3. Once you have reached the desired end time, press the button again.

4. Press the

button to activate the programmed mode.

The

and buttons will ash alternately to indicate that programming

has taken place; in the time before cooking starts, the TIME display will show

the duration and the cooking end time alternately.

5. Once cooking has nished, “END” appears on the TEMPERATURE display

and a buzzer sounds.

• For example: it is 9:00 a.m. and a time of 1 hour and 15 minutes is

programmed, while the end time is set to 12:30. The programme will

start automatically at 11:15 a.m.

To cancel programming press the

button.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-assisted cooking. This is

because excessive direct heat can burn temperature sensitive foods.

! In the GRILL and FAN GRILLING cooking modes, particularly when using

the rotisserie spit, place the dripping pan in position 1 to collect cooking

residues (fat and/or grease).

MULTILEVEL

• Use positions 2 and 4, placing the food which requires more heat on 2.

• Place the dripping pan on the bottom and the rack on top.

GRILL

• Place the rack in position 3 or 4. Position the food in the centre of the rack.

• We recommend that the temperature is set to its maximum level. The top

heating element is regulated by a thermostat and may not always operate

constantly.

PIZZA

• Use a lightweight aluminium pizza pan. Place it on the rack provided.

For a crispy crust, do not use the dripping pan as this extends the total

cooking duration and prevents the crust from forming.

• If the pizza has a lot of toppings, we recommend adding the mozzarella

cheese to the top of the pizza halfway through the cooking process.

Modes Foods Weight

(in kg)

Preheating

Manual

Standard

guide

rails

Sliding

guide

rails

Multilevel*

1+1

2 and 4

1 and 2/3

1 or 2

2 and 4

1 and 3

yes

20-25

30-35

20-30

65-75

45-50

30-35

35-40

20-25

10-20

20-25

25-35

Grill*

0,7

0,5

0,8

0,7

n° 4 or 5

n° 4 or 6

3 or 4

2 or 3

300

10-20

10-15

15-20

10-20

10-12

3-5

70-80

Fan grilling*

1,5

210

200

210

55-60

30-35

70-80

60-70

60-75

70-80

40-45

Pizza*

Pizza

Focaccia bread

0,5

yes

15-20

20-25

Baking*

0,5

0,7

0,6

0,7

0,8

0,5

2 or 3

2 and 4

2 or 3

1 and 3

1 or 2

1 and 3

1 or 2

1 and 2

yes

180

180-190

160-170

180-190

180

200

210

25-35

40-50

45-55

20-25

35-40

20-30

20-25

30-35

180

20-25

Automatic**

Roast

Roast dishes12 or 32 no

Bread***

Bread (see recipe)

11 or 21 no

Baked cakes

12 or 32 no

Tarts

0,52 or 32 no

Cooking advice table

Rack position Recommended

Temperature

(°C)

Cooking

duration

(minutes)

1 and 3 and 5

1 and 2 and 4

50 0,5

210-220

180

160-170

200-210

190-200

180

180-190

190

180

210

190-200

210-220

190-200

Turnspit*

Chicken on the turnspit

Duck on the turnspit

Chicken

Chicken/poultry

Pastries

1,5

250

70-80

60-70

1,2-1,5

2 o 32 no

Precautions and tips

! This appliance has been designed and manufactured in compliance with

international safety standards. The following warnings are provided for safety

reasons and must be read carefully.

General safety

• The appliance was designed for domestic use inside the home and is

not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in covered areas. It is

extremely dangerous to leave the appliance exposed to rain and storms.

• When moving or positioning the appliance, always use the handles

provided on the sides of the oven.

• Do not touch the appliance while barefoot or with wet or damp hands and

feet.

• The appliance must be used by adults only for the preparation of

food, in accordance with the instructions provided in this booklet.

Any other use of the appliance (e.g. for heating the room) constitutes

improper use and is dangerous. The manufacturer may not be held

responsible for any damage caused as a result of improper, incorrect

and unreasonable use of the appliance.

• Do not touch the heating elements or certain parts of the oven door

when the appliance is in use; these parts become extremely hot.

Keep children well away from the appliance.

• Make sure that the power supply cables of other electrical appliances do

not come into contact with the hot parts of the oven.

• The ventilation and heat dispersal openings must never be obstructed.

• Always grip the oven door handle in the centre: the ends may be hot.

• Always use oven gloves when placing cookware in the oven or when

removing it.

• Do not use aluminium foil to line the bottom of the oven.

• Do not place ammable materials in the oven: if the appliance is switched

on accidentally, the materials could catch re.

• When unplugging the appliance, always pull the plug from the mains

socket; do not pull on the cable.

• Do not perform any cleaning or maintenance work without having

disconnected the appliance from the electricity mains.

• If the event of malfunctions, under no circumstances should you attempt

to perform the repairs yourself. Contact an authorised Service Centre (see

Assistance).

• Do not rest objects on the open oven door.

• Do not let children play with the appliance.

• The appliance should not be operated by people (including children)

with reduced physical, sensory or mental capacities, by inexperienced

individuals or by anyone who is not familiar with the product. These

individuals should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary instructions

relating to the operation of the appliance.

• The appliance is not intended to be operated by means of an external

timer or separate remote-control system.

Disposal

• When disposing of packaging material: observe local legislation so that

the packaging may be reused.

• The European Directive 2012/19/EU on Waste Electrical and

Electronic Equipment (WEEE), requires that old household electrical

appliances must not be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected separately in order

to optimise the recovery and recycling of the materials they contain

and reduce the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product reminds you of your

obligation, that when you dispose of the appliance it must be separately

collected.

Consumers should contact their local authority or retailer for information

concerning the correct disposal of their old appliance.

Respecting and conserving the environment

• Whenever possible, avoid pre-heating the oven and always try to ll it.

Open the oven door as little as possible because heat is lost every time

it is opened. To save a substantial amount of energy, simply switch off

the oven 5 to 10 minutes before the end of your planned cooking time

and use the heat the oven continues to generate.

• Automatic programmes are based on standard food product.

• Keep gaskets clean and tidy to prevent any door energy losses

• If you have a timed tariff electricity contract, the “delay cooking” option

will make it easier to save money by moving operation to cheaper time

periods.

! This product complies with the requirements of the latest European Directive

on the limitation of power consumption of the standby mode.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before carrying out

any work on it.

Cleaning the appliance

• Slight differences in colour on the front of the oven are due to the different

materials used, i.e. glass, plastic or metal.

• Any shady areas resembling grooves on the oven door glass are caused

by reections from the oven light.

• The enamel is branded at very high temperatures. This process may cause

colour variations. This is normal and will not affect appliance operation in

any way. The thin edges of the sheet metal cannot be entirely enamelled

and may therefore appear to be unnished. This will not affect the rust

protection.

• The stainless steel or enamel-coated external parts and the rubber seals

may be cleaned using a sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for the removal of stubborn

stains. After cleaning, rinse and dry thoroughly. Do not use abrasive

powders or corrosive substances.

• The inside of the oven should ideally be cleaned after each use, while it is

still lukewarm. Use hot water and detergent, then rinse well and dry with

a soft cloth. Do not use abrasive products.

• All accessories - with the exception of the sliding racks - can be washed

like everyday crockery, and are even dishwasher safe.

• We recommend that detergents are not sprayed directly onto the control

panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and a non-abrasive

cleaning product, then dry thoroughly with a soft cloth. Do not use rough

abrasive material or sharp metal scrapers as these could scratch the surface

and cause the glass to crack.

For more thorough cleaning purposes, the oven door may be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F located on the two

hinges (see diagram).

3. Grip the door on the two outer sides and

close it approximately half way. Pull the

door towards you, lifting it out of its slot (see

diagram). To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals are damaged,

please contact your nearest Service Centre (see Assistance). We recommend

that the oven is not used until the seals have been replaced.

Replacing the light bulb

To replace the oven light bulb:

1. Remove the glass cover of the

lamp-holder.

2. Remove the light bulb and replace

it with a similar one: halogen lamp

voltage 230 V, wattage 25 W, cap

G 9.

3. Replace the glass cover (see

diagram).

! Do not touch the light bulb directly with your hands.

! Do not use the oven lamp as/for ambient lighting.

Automatic cleaning with the PYROLYSIS function

With the PYROLYSIS mode, the internal temperature of the oven reaches

500°C. The pyrolytic cycle is activated, burning away food and grime

residues. Dirt is literally incinerated.

Keep children away from the appliance during the automatic cleaning cycle

as surfaces may become very hot. Particles may ignite inside the oven as a

result of the combustion process. There is no cause for concern: this process

is both normal and hazard-free.

Before initiating the PYROLYSIS mode:

• clean the oven door;

• remove large or coarse food residues from the inside of the oven using a

damp sponge. Do not use detergents;

• remove all accessories and the sliding rack kit (where present);

• do not place tea towels or pot holders over the oven handle.

! If the oven is too hot, the pyrolytic cycle may not start. Wait for the oven to

cool down.

! The programme may only be started once the oven door has been closed.

To activate the PYROLYSIS programme:

1. Switch the control panel on by pressing the

button.

2. Press the

button; the TIME display will show the default duration of

1:30 h (normal cycle), while he TEMPERATURE display will show “Piro” and

“nor” alternately;

3. The desired cleaning level can be selected by pressing the

button, then:

- pressing “

” to switch to the intensive cycle: the duration is 2 h and the

TEMPERATURE display shows the text “Piro” and “int” alternately;

- pressing “

” to switch to the economy cycle: the duration is 1 h and the

TEMPERATURE display shows the text “Piro” and “eco” alternately.

Safety devices

• the door locks automatically as soon as the temperature reaches a high

value; the

icon lights up on the display;

• pressing the

button cancels the cleaning cycle t any time;

• if a malfunction occurs, the heating elements will be switched off;

• once the oven door has been locked, you cannot change the duration and

end time settings.

Glass cover

Lamp

Holder

compartment

Programming delayed automatic cleaning

! Programming is possible only after selecting the PYROLYSIS mode.

1.Press the button and set the end time using the“ ” and “ ” buttons.

2. Once you have reached the desired end time, press the button again.

3. Press the

button to activate the programmed mode.

4. When the selected time has elapsed, “END” appears on the TEMPERATURE

display and a buzzer sounds.

• For example: it is 9:00 a.m. and the Economy (ECO) PYROLYSIS level

has been selected, with the default duration of 1 hour. 12:30 is scheduled

as the end time. The programme will start automatically at 11:30 a.m.

The icons

and ash to indicate that programming has taken place.

After programming, in the time before the PYROLYSIS mode starts, the TIME

display indicates the duration and end of the PYROLYSIS mode alternately.

To cancel programming press the

button.

Once the automatic cleaning cycle is over

Before you can open the oven door, you will have to wait for the

icon to

switch off: this indicates the oven temperature has dropped to an acceptable

level. You will notice some white dust deposits on the bottom and the sides

of your oven; remove these deposits with a damp sponge once the oven

has cooled down completely. Alternatively, you can make use of the already

heated oven, in which case it is not necessary to remove the deposits, they

are completely harmless and will not affect your food in any way.

The “Clock button” and the digits on the

display flash.

Problem Possible cause Solution

The appliance has just been connected to the

electricity mains or there has been a blackout.

Set the clock.

A programmed cooking mode does not

start.

There has been a blackout.

Reprogram the cooking mode.

Only the high luminosity “Clock button”

is lit.

The appliance is in standby mode. Press any button to exit standby mode.

The temperature inside the oven is higher

than the suggested value for the selected

mode.

An automatic mode has been selected.

“Hot” appears on the display and

cooking does not start.

Wait for the oven to cool down.

Fan-assisted cooking has been

selected and the food looks burnt.

Positions 1 and 5: the direct heat could cause

temperature-sensitive foods to burn.

We recommend switching dripping pan

positions halfway through cooking.

Troubleshooting

Installation

! Conservez ce mode d’emploi pour pouvoir le consulter à tout moment.

En cas de vente, de cession ou de déménagement, veillez à ce qu’il suive

l’appareil pour informer le nouveau propriétaire sur son fonctionnement et lui

fournir les conseils correspondants.

! Lisez attentivement les instructions : elles contiennent des conseils

importants sur l’installation, l’utilisation et la sécurité de votre appareil

Positionnement

! Les emballages ne sont pas des jouets pour enfants, il faut les mettre au

rebut en respectant la réglementation sur le tri sélectif des déchets (voir

Précautions et conseils).

! L’installation doit être effectuée par un professionnel du secteur

conformément aux instructions du fabricant. Une mauvaise installation peut

causer des dommages à des personnes, des animaux ou des biens.

Encastrement

Pour garantir le bon fonctionnement de l’appareil, il faut que le meuble possède

des caractéristiques bien précises:

• les panneaux adjacents doivent être fabriqués dans un matériau résistant

à la chaleur;

• dans le cas de meubles en plaqués bois, les colles doivent pouvoir résister

à une température de 100 °C;

• la cavité du meuble pour encastrement du four, tant sous plan (voir gure)

qu’en colonne , doit avoir les dimensions suivantes:

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

560 mm.

547 mm. min.

! Après encastrement de l’appareil, il ne doit plus y avoir possibilité de contact

avec les parties électriées. Les déclarations de consommation indiquées sur

la plaque signalétique ont été mesurées pour ce type d’installation.

Aération

Pour garantir une bonne aération, la cavité d’encastrement doit être dépourvue

de paroi arrière. Il est conseillé d’installer le four de manière à ce qu’il repose

sur deux cales en bois ou bien sur un plan d’appui continu qui ait une découpe

d’au moins 45 x 560 mm (voir gures).

560 mm.

45 mm.

Centrage et xation

Positionner les 4 taquets situés sur les côtés du four en face des 4 trous

pratiqués sur le cadre et les régler selon l’épaisseur de la joue du meuble :

épaisseur 20 mm : enlever la partie amovible

du taquet (voir figure);

épaisseur 18 mm : utiliser la première rainure,

comme prévu par le fabricant (voir figure);

épaisseur 16 mm : utiliser la deuxième rainure

(voir figure).

Pour xer l’appareil au meuble : ouvrir la porte du four et visser 4 vis à bois

dans les 4 trous du cadre.

! Toutes les parties qui servent de protection doivent être xées de manière

à ne pouvoir être enlevées qu’avec l’aide d’un outil.

Raccordement électrique

Les fours munis d’un câble d’alimentation tripolaire sont prévus pour un

fonctionnement au courant alternatif à la tension et à la fréquence indiquées

sur la plaque signalétique apposée sur l’appareil (voir ci-dessous).

Montage du câble d’alimentation

1. Pour ouvrir le bornier, faire pression à

l’aide d’un tournevis sur les languettes

latérales du couvercle : tirer et ouvrir le

couvercle (voir gure).

2. Montage du câble d’alimentation :

dévisser la vis du serre-câble ainsi que

les trois vis des contacts L-N-

puis

xer les ls sous les têtes de vis en

respectant les couleurs Bleu (N) Marron

(L) Jaune-Vert

(voir gure).

3. Fixer le câble dans le serre-câble

prévu.

4. Fermer le couvercle du bornier.

Branchement du câble d’alimentation au réseau électrique

Montez sur le câble une prise normalisée adaptée à la charge indiquée sur

l’étiquette des caractéristiques.

En cas de raccordement direct au réseau, il faut intercaler entre l’appareil

et le réseau un interrupteur à coupure omnipolaire ayant au moins 3 mm

d’écartement entre les contacts, dimensionné à la charge et conforme aux

normes en vigueur (le l de terre ne doit pas être interrompu par l’interrupteur).

Le câble d’alimentation ne doit atteindre, en aucun point, des températures

dépassant de 50°C la température ambiante.

! L’installateur est responsable du bon raccordement électrique de l’appareil

et du respect des normes de sécurité.

Avant de procéder au branchement, assurez-vous que :

• la prise est bien munie d’une terre conforme à la loi;

• la prise est bien apte à supporter la puissance maximale de l’appareil,

indiquée sur la plaquette signalétique;

• la tension d’alimentation est bien comprise entre les valeurs indiquées sur

la plaquette signalétique;

• la prise est bien compatible avec la che de l’appareil. Si ce n’est pas le

cas, remplacez la prise ou la che, n’utilisez ni rallonges ni prises multiples.

! Après installation de l’appareil, le câble électrique et la prise de courant

doivent être facilement accessibles

! Le câble ne doit être ni plié ni excessivement écrasé.

! Il doit être contrôlé périodiquement et ne peut être remplacé que par un

technicien agréé (voir Assistance).

! Nous déclinons toute responsabilité en cas de non respect des normes

énumérées ci-dessus.

* Uniquement pour les modèles avec glissières embouties.

** Uniquement pour les modèles avec glissières en fil.

PLAQUE SIGNALETIQUE

Dimensions*

largeur 43,5 cm

hauteur 32,4 cm

profondeur 41,5 cm

Volume*

L. 59

Raccordements

électriques

tension 220-240V~ 50Hz

(voir plaque signalétique)

puissance maximum absorbée

2800W

Directive de l’UE n ° 65/2014

intégrant la directive 2010/30/UE.

Règlement n ° 66/2014 de l’UE

intégrant la directive 2009/125/CE.

la norme EN 60350-1

la norme EN 50564

Consommation énergie déclaration

Classe convection Forcée –

fonction four: PÂTISSERIE

Dimensions**

largeur 45,5 cm

hauteur 32,4 cm

profondeur 41,5 cm

Volume**

L. 62

Etiquette

Energie e

Écoconception

Cet appareil est conforme aux

Directives Communautaires

suivantes : 2006/95/UE du

12.12.06 (Basse Tension) et

modifications successives -

2004/108/UE du 15.12.04

(Compatibilité Électromagnétique)

et modifications successives -

93/68/CEE du 22/07/93 et

modifications successives.

- 2012/19/UE et modifications

successives.

- 1275/2008 standby/off mode

Mise en marche et utilisation

ATTENTION! Le four est équipé

d’un système d’arrêts de grilles

qui permet de les retirer sans que

ces dernières sortent entièrement

du four (1).

Pour sortir complètement les grilles

il suffit, comme illustré, de les

soulever en les saisissant par

l’avant et de les tirer (2).

! Lors de son premier allumage, faire fonctionner le four à vide, porte fermée,

pendant au moins une heure en réglant le thermostat sur le maximum. Puis

éteindre le four, ouvrir la porte et aérer la pièce. L’odeur qui se dégage est

due à l’évaporation des produits utilisés pour protéger le four.

! Pour simplier les sélections, garder les touches “

” et “ ” enfoncées ; les

numéros délent plus rapidement.

! Chaque sélection est automatiquement mémorisée pendant 10 secondes.

! Quand on porte les gants, il est impossible d’actionner les touches.

! Pour optimiser les performances de cuisson, un réglage des paramètres du

produit est effectué au moment de l’activation de la fonction sélectionnée, ceci

peut entraîner un retard d’allumage du ventilateur et des éléments chauffants.

Verrouillage de commandes

! Les commandes peuvent être verrouillées four éteint, cuisson en cours ou

terminée ou bien en programmation.

Pour verrouiller les commandes du four, appuyer sur la touche

pendant

au moins 2 secondes. Un signal sonore retentit et le symbole clé «O--n»

apparaît sur l’afcheur TEMPÉRATURE. L’icône allumée indique que

le verrouillage est activé. Pour déverrouiller, appuyer à nouveau sur la touche

pendant au moins 2 secondes.

Régler l’horloge

! L’horloge n’est réglable que four éteint. Si le four est en mode veille (standby),

une première pression sur la touche

afche l’heure courante. Appuyer à

nouveau pour régler l’heure.

Après branchement au secteur ou après une panne de courant, la touche

et les chiffres de l’afcheur TEMPS se mettent à clignoter pendant 10

secondes.

Pour régler l’horloge :

1. Appuyer sur la touche

2. Régler l’heure à l’aide des touches “ ” et “ ”.

3. Une fois l’heure exacte atteinte, appuyer à nouveau sur la touche

4. procéder comme sus-indiqué pour les minutes aussi.

En cas de panne de courant, il faut remettre l’horloge à l’heure. L’icône

qui

clignote sur l’afcheur signale que l’horloge a besoin d’être réglée.

Régler le minuteur

! Le minuteur est toujours réglable tant four éteint que four allumé. Il ne contrôle

pas l’allumage et l’arrêt du four.

Une fois le temps écoulé, le minuteur émet un signal sonore qui s’arrête

automatiquement au bout de 30 secondes ou après avoir appuyé sur une

touche active quelconque.

Pour régler la minuterie :

1. Appuyer sur la touche

2.Sélectionner le temps désiré à l’aide des touches “ ” et “ ”

3. Une fois la sélection voulue atteinte, appuyer à nouveau sur la touche

L’icône

allumée signale que le minuteur est activé.

Pour annuler la sélection de la minuterie, appuyer sur la touche

et à l’aide

des touches “ ” et “ ” ramener le temps à 00:00. Appuyer à nouveau sur

la touche

L’icône

éteinte signale que le minuteur est désactivé.

Mise en marche du four

1. Appuyer sur la touche pour allumer le panneau de commande.

L’appareil émet un triple son ascendant et toutes les touches s’allument à

la suite.

2. Appuyer sur la touche du programme de cuisson souhaité. L’écran

TEMPÉRATURE afche :

- en cas de programme manuel, la température associée au programme ;

- «Auto» en cas de programme automatique.

l’écran TEMPS afche :

- en cas de programme manuel, l’heure courante ;

- la durée en cas de programme automatique.

3. Appuyer sur la touche

pour démarrer la cuisson.

4. Le four se place en préchauffage, les indicateurs de montée en température

s’éclairent progressivement au fur et à mesure que la température augmente.

5. Un signal sonore suivi de l’allumage de tous les indicateurs de préchauffage

signale la n du préchauffage. Il est temps d’enfourner les plats.

6. En cours de cuisson, il est possible à tout moment de :

- modier la température en appuyant sur les touches

puis sur les touches

“ ” et “ ” (seuls programmes manuels) ;

- programmer la durée d’une cuisson (voir Programmes) ;

- stopper la cuisson en appuyant sur la touche

. Dans ce cas, l’appareil

se rappelle de la température éventuellement modifiée précédemment

(uniquement pour programmes manuels).

- éteindre le four en gardant la touche

enfoncée pendant 3 secondes.

7. En cas de coupure de courant, si la température du four n’est pas trop

redescendue, un dispositif spécial fait repartir le programme à partir du moment

où il a été interrompu. Les programmations en attente de démarrage ne sont

par contre pas rétablies et doivent être reprogrammées dès rétablissement

du courant (par exemple : un départ de cuisson a été programmé à 20h30. A

19h30, il y a une coupure de courant. Après rétablissement du courant, il faut

reprogrammer).

! Aucun préchauffage n’est prévu pour le programme BARBECUE.

! Ne jamais poser d’objets à même la sole du four, l’émail risque de s’abîmer.

! Il faut toujours enfourner les plats sur la grille fournie avec l’appareil.

Ventilation de refroidissement

Pour obtenir un abaissement des températures extérieures, un système de

refroidissement soufe de l’air à l’extérieur par une fente située entre le tableau

de bord, la porte du four et la partie basse de la porte du four.

Au début du programme PYROLYSE le système fonctionne à faible vitesse.

! Le ventilateur continue à tourner après l’arrêt du four jusqu’à ce que ce

dernier se soit sufsamment refroidi.

Eclairage du four

L’éclairage s’allume à l’ouverture de la porte du four ou au démarrage d’un

programme de cuisson.La touche

permet d’allumer ou éteindre l’éclairage

à tout moment.

Indicateurs de chaleur résiduelle

Cet appareil est équipé d’un indicateur de chaleur résiduelle. Four éteint,

l’afcheur signale par allumage de la barre de “chaleur résiduelle” la présence

de température à l’intérieur de l’enceinte. Les éléments de la barre s’éteignent

au fur et à mesure que la température à l’intérieur du four baisse.

Mode Demo (Démonstration)

Le four peut fonctionner en mode DEMO : dans ce cas, tous les éléments

chauffants sont désactivés et seules les commandes fonctionnent.

Pour activer le mode DEMO, appuyer brièvement sur la touche

, puis sur

les touches “ ” et “ ” simultanément pendant 6 secondes, appuyer ensuite

brièvement sur la touche

. Un signal sonore retentit et le message «

dEon » apparaît sur l’afcheur TEMPÉRATURE.

Pour désactiver le mode de fonctionnement DEMO, quand le four est éteint,

appuyer simultanément sur la touche

et sur la touche “ ” pendant 3

secondes. Un signal sonore retentit et le message « dEof » est afché.

Rétablissement des réglages d’usine

Le four peut retourner à ses paramètres de réglage usine, il suft pour cela de

réinitialiser toutes les sélections effectuées par l’utilisateur (horloge et durées

personnalisées). Pour procéder à la réinitialisation, éteindre le four, garder enfoncées

pendant 6 secondes de suite la touche de la première cuisson manuelle en haut

à gauche ainsi que la touche

. Une fois que la réinitialisation a eu lieu, un

signal sonore retentit. Dès la première pression sur la touche

il y a retour à

la première mise en service.

Standby

Ce produit est conforme à la nouvelle Directive européenne sur la réduction

de la consommation d’énergie en mode veille (standby). Sans opérations

pendant 30 minutes et si aucun verrouillage de touches ou de porte n’a

été sélectionné, l’appareil se place automatiquement en mode veille. Le

mode standby est signalé par l’intense luminosité de la «touche horloge».

A la moindre intervention sur l’appareil, le système se remet en mode de

fonctionnement normal.

Programmes

! A chaque allumage, le four propose le premier programme de cuisson

manuel.

Programmes de cuisson manuels

! Tous les programmes ont une température de cuisson présélectionnée. Il

est possible de la régler manuellement, entre 30°C et 250°C au choix (300°C

pour le programme BARBECUE). Toute modication de la température

sera mémorisée et reproposée dès la prochaine utilisation du programme.

Si la température choisie est inférieure à la température intérieure du four,

l’afcheur TEMPÉRATURE afche « Hot ». Il est toutefois possible de

démarrer la cuisson.

Programme MULTINIVEAUX

Mise en marche de tous les éléments chauffants ainsi que de la turbine. La

chaleur est constante et bien répartie à l’intérieur du four, l’air cuit et dore de

façon uniforme en tous points. Il est possible de cuire au maximum sur deux

niveaux en même temps.

Programme BARBECUE

Mise en marche de la résistance de voûte et du tournebroche (si l’appareil en

est équipé). La température élevée et directe du gril est conseillée pour tous

les aliments qui exigent une haute température en surface. La cuisson doit

avoir lieu porte du four fermée (voir « Conseils de cuisson »).

Programme TOURNEBROCHE

Cette fonction est optimisée pour les cuissons au tournebroche. Cuissons

porte du four fermée.

Programme GRATIN

Mise en marche de la résistance de voûte, de la résistance circulaire

(pendant un certain temps) et de la turbine et du tournebroche (si l’appareil

en est équipé). L’irradiation thermique unidirectionnelle s’ajoute au brassage

de l’air pour une répartition uniforme de la chaleur dans l’enceinte du four.

Plus de risque de brûler les aliments en surface et plus grande pénétration

de la chaleur. La cuisson doit avoir lieu porte du four fermée (voir « Conseils

de cuisson »).

Programme PIZZA

Mise en marche de la résistance de voûte et de la résistance circulaire ainsi

que de la turbine. Cette combinaison permet une montée en température

rapide du four. En cas de cuisson sur plusieurs niveaux, ne pas oublier de

les changer de place à mi-cuisson.

Programme PÂTISSERIE

Mise en marche de la résistance arrière et de la turbine pour obtenir

une chaleur douce et uniforme à l’intérieur du four. Cette fonction est

particulièrement indiquée pour la cuisson de mets délicats (comme, par

exemple, les gâteaux levés).

Tournebroche

Pour actionner le tournebroche (voir

gure), procéder comme suit :

1. placer la lèchefrite au niveau 1 ;

2. placer le berceau au niveau 3

et encastrer le bout arrière de la

broche dans le trou situé au fond de

l’enceinte ;

3. pour actionner le tournebroche

sélectionner les programmes

;

! Quand le programme est lancé, le tournebroche s’arrête dès ouverture de

la porte du four.

La page charge ...

Indesit FRI 886.1 MT Mode d'emploi

Marque: Indesit

Modèle: FRI 886.1 MT

Catégorie: Fours

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Indesit FRI 886.1 MT User guide

Indesit FRI 886.1 MT Mode d'emploi

Indesit FRI 886.1 MT Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents