XPOWER FC-100 Mode d'emploi

Air Circulator Owner's Manual

Ciculador de Aire Manual de Usuario

Circulateur d'air Manuel d'emploi

Model / Modelo / Modèle:

FC-100, FC-200 Series, FC-300 Series, FC-420

(115V~ 60HZ)

Read and save these instructions

Lea y guarde estas instrucciones

Lisez et gadez ces instructions

www.xpower.com | 1-(855)-855-8868 | info@xpower.com

Index: NA-1-A9

Edition: 7.1.Final

English - 2

Safety Instructions

!WARNING - READ AND SAVE THIS INSTRUCTIONS BEFORE USING THIS PRODUCT.

The user of electrical products may create hazards that include, but are not limited to

injury, fire, electrical shock. Failure to follow these instructions may damage and/or

impair its operation and void the warranty.

• Before operating, remove all packaging material and check for any damage that may

have occurred during shipping or any missing items.

• Check household power supply to ensure it matches the appliance’s specification.

• DO NOT operate any fan with a damaged cord or plug. Discard fan or return it to an

authorized service facility for examination and/or repair.

• Use only on GFCI protected receptacles. Please contact a qualified electrician for

verification and / or installation of a GFCI receptacle if necessary.

• DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or

similar coverings. DO NOT route cord under furniture or appliances. Arrange cord away

from traffic area and where it will not be tripped over.

• To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state

speed control device.

• DO NOT touch this appliance or the plug with wet hands or while standing in water.

• DO NOT operate the appliance in any pooled water.

• DO NOT use the product in areas where gasoline, paint or other flammable goods and

objects are used or stored.

• DO NOT insert or allow objects to enter any ventilation or exhaust opening as this may

damage the appliance and void the warranty.

• DO NOT cover the air inlet or outlet on the appliance.

• DO NOT direct the air flow at human faces or bodies.

• DO NOT allow children to play with this appliance.

• AUTOMATICALLY OPERATED DEVICE – To reduce the risk of injury, disconnect from

power supply before servicing.

• Remove the power cord from the electrical receptacle by grasping and pulling on the

power cord plug-end only, DO NOT pull the cord directly.

• DO NOT attempt to repair or adjust any electrical or mechanical functions of this

appliance, as this may cause danger and void the warranty.

• If the appliance is damaged or it malfunctions, DO NOT continue to use it. Unplug the

product from the electrical outlet. Refer to troubleshooting guide or contact XPOWER.

• Store in a dry area, away from exposure to sunlight, extreme temperature and humidity,

or other extreme environments, when not in use.

• For model FC-100 / FC-200 Series, DO NOT stack more than six units of this appliance.

For model FC-300 / FC-420, DO NOT stack more than five units of this appliance.

• An electronic instruction manual can be obtained through manufacturer’s website

www.xpower.com.

English - 3

Items Included

Axial Fan Owner's Manual

XXX Manual De Usuario (página 10)

XXX Mode d'emploi (page 18)

Model / Modelo / Modèle:

P-80 Series, P-100 Series, P-200 Series

(115V 60HZ)

Read and save these instructions before use

Lea y guarde estas instrucciones antes de usar la unidad

Lire et conserver ces instructions avant utilisation

www.xpower.com | 1-(855)-8868 | [email protected]

Index: NA-1-A2

Edition: 1.0.Alpha

• Owner’s Manual x 1

• Air Circulator

Body x 1**• Air Circulator x 1* • Rack x 1**

• Rack Handle x 2**

• Rubber Washer

x 2**

* For model FC-100/FC-200 Series/FC-420 only.

The exact appearance of the products might be slightly different from the diagram.

** For model FC-300 Series only.

English - 4

Air Circulator Introduction

• XPOWER Air Circulators are designed to offer

efficient air circulation and ventilation with its

high and long-distance focused airflow.

• It’s perfect for air circulation and ventilation in

janitorial/sanitation jobs, air condition control

and more.

* / ** / *** / **** These functions do not apply all models mentioned in this manual.

(See Page 11: Technical Specification)

Parts Description

(1) Front Grille Cover

(2) Motor

(3) Housing

(4) Capacitor

(5) Housing Handle

(6) Switch Plate*/ Switch

and Timer Plate**

(7) Additional Electrical

Receptacle *** / Timer

Plate ****

(8) Rack Handle

(9) Rubber Washer

(10) Rack

(11) Fan

(12) Rear End Cover

(13) Rear Grille Cover

(14) Power Cord

1

2

10

13

12

14

11

3

8

9

8

6

7

5

4

English - 5

Installing the Rack*

①

③

②

③

① Fit both rubber washers onto bolts on both sides of unit.

② Align the rack onto the air circulator.

③ Fasten the connection with the rack handle.

* For model FC-300 Series only.

Installation and Operation Guide

Switch Plate

OFF

1

2 3

4

Four Speed Control

OFF 5

1

2 3

4

Five Speed Control

OFF

MAX

LOW

Variable Speed Control

Four Speed Switch ( For model FC-100/FC-200/FC-300 Series only)

• Turn to “OFF” position to switch the machine OFF. Turn to any speed position to switch

the machine ON.

• Turn clockwise to set the desired speed. There are 4 speeds from: 4, 3, 2, 1. “4” is the

highest speed and “1” is the lowest speed .

English - 6

Switch Plate (Continued)

Five Speed Switch (For model FC-420 only)

• Turn to “OFF” position to switch the machine OFF. Turn to any speed position to switch

the machine ON.

• Turn clockwise to set the desired speed. There are 5 speeds from: 5, 4, 3, 2, 1. “5” is

the highest speed and “1” is the lowest speed.

Variable Speed Switch (For model FC-250D/FC-250AD only)

• Turn to “OFF” position to switch the machine OFF. Turn clock-wisely to any position

between “MAX” and “LOW” to switch the machine ON.

• You can adjust to any desired speed variably. “MAX” is the higest speed and “LOW” is

the lowest speed.

* For model FC-250AD and FC-300A only.

Additional Electrical Receptacle (Daisy Chain)*

CIRCUIT BREAKER

12A

TOTAL OUTPUT

12 AMPS MAX WITH THIS UNIT OFF

10 AMPS MAX WITH THIS UNIT ON

• Other appliances can be plugged in the

additional electrical receptacles and work

whether the machine is on or off. However,

the total amperage must be lower than the

amperage instructed. Different models may

have varying instructions.

• If the machine or the plugged in appliance

stops working, press the RESET BUTTON to

reset the circuit.

• Turn clockwise to set timer for minutes count

down to an automatic stop.

• The timer can be set for up to 180 minutes (3

hours).

• When the timer reaches “0” position, the unit

stops working. On “ON” position, it will work

constantly.

Timer Switch*

120

60

0

ON

180

* For model FC-100/FC-200/FC-250D/FC-300/FC-420 only.

English - 7

Adjust Operation Position

• The Air Circulator features 360° Rotation. Tilt Air Circulator to desired angle and

screw on rack handles to secure the position.

Use without Rack*

• Uninstall the rack and place the

Air Circulator on a level surface.

* For model FC-420 only.

English - 8

Transportation

Lift with Handle

• Lift the Air Circulator with the

handle on the top.

User Maintenance Instructions

Frequent maintenance is recommended on this appliance. Failure to follow the

maintenance instructions may cause failure of the appliance and void the warranty.

• When not in use, unplug and store the appliance in a dry and cool indoor place. Make

sure it’s out of reach of children.

• Before performing any maintenance or cleaning, always disconnect the Air Circulator

from its power source.

• Use a damp cloth to wipe the surface of the housing. Do not clean the unit with water

directly.

• Check if the grille covers are clean. Remove dirt or any other objects that could block

the air inlet and air outlet.

Fasten the Rack Handles

• To prevent possible injury, when

you finish using this appliance,

please position the Air Circulator

UPRIGHT.

• Fasten the rack handle to lock the

position of the Air Circulator.

English - 9

Organize the Power Cord

• Wrap the power cord around the housing.

• Clip the cord to the cord clip on the plug shown above.

Stack Multiple Units

• Stack the Air Circulators on the sides. Align the air

inlets of both Air Circulators.

WARNING

• For model FC-100 / FC-200 Series, DO NOT stack

more than six units of this appliance.

• For model FC-300 Series / FC-420, DO NOT stack

more than five units of this appliance.

• Stacking function is not secure during transportation.

!

English - 10

Troubleshooting Guide

PROBLEM POSSIBLE CAUSE SOLUTION

Air Circulator does

not start

No electricity. Check for power supply.

The power cord is not properly

plugged in.

Remove and reconnect the

power cord.

The circuit breaker on the

additional electrical receptacle

(Daisy chain) jumps.*

Remove all appliance on

the additional electrical

receptacle and press “Reset”.

The timer switch is set to “0”

position.*

Set the timer switch to “ON”

position.

Unit runs but the

speed is abnormal

Air inlet or air outlet is blocked. Remove blockage.

* These functions do not apply to all models mentioned in this manual.

If troubleshooting does not resolve your problem, please contact XPOWER or other

parties authorized by XPOWER for further instructions.

English - 11

Technical Specication

MODEL NUMBER FC-100 FC-200 FC-250D FC-250AD FC-300 FC-300A FC-420

Voltage/Frequency 115 V~60 Hz

Amperage 0.6 A 1.0 A 0.9 A 1.0 A 2.8 A

Motor Power - - 1/4 HP 1/3 HP

Rated Airflow 1100

CFM 1300

CFM 1560

CFM 2100 CFM 3600

CFM

Speed Control 4 Speeds Variable Speeds 4 Speeds 5 Speeds

Timer 3 Hours (OFF) N/A 3 Hours

(OFF) N/A 3 Hours

(OFF)

Additional Electrical

Re-ceptacle N/A Yes N/A Yes N/A

Cord Length 6 ft. / 1.8 m 10 ft. / 3.0 m 20 ft. /

6.1 m 15 ft. /

4.5 m

Housing PP ABS

Unit Dimension

(L) x (W) x (H)

16.1 x 8.9

x 14.2 in.

/ 41.0 x

22.5 x

36.0 cm

17.3 x 8.9 x 15.4 in. / 44.0 x 22.5 x

39.0 cm

18.6 x 9.4 x 19.2 in. /

47.2 x 23.9 x 48.8 cm

21.9 x 9.8

x 22.5 in.

/ 55.6

x 24.9 x

57.1 cm

Unit Weight 9.7 lbs. /

4.4 kg 10.1 lbs.

/ 4.6 kg 11.1 lbs.

/ 5.0 kg 11.7 lbs.

/ 5.3 kg 13.0 lbs.

/ 5.9 kg 14.5 lbs.

/ 6.57 kg 23.4 lbs.

/ 10.6 kg

Safety Cer-tification ETL / C-ETL

If your product(s) is not listed above, please visit www.xpower.com for more information.

English - 12

XPOWER Limited Warranty (USA)

1 YEAR LIMITED WARRANTY

XPOWER-branded products purchased in the U.S. from authorized distributors include

a 1-year limited warranty. Contact XPOWER to confirm warranty information about your

product(s).

This limited warranty covers defects in materials and workmanship in your XPOWER-

branded products, purchased in the U.S. ONLY. Local warranty policy (if any) in your

country will cover products purchased outside the U.S.

Items mentioned but not limited to below are not covered by warranty:

(1) Power cord, filters or any other components considered as a “consumable parts” by

XPOWER.

(2) Normal wear and tear.

(3) Problems that result, directly or indirectly, at XPOWER’s sole discretion, from:

(3.1) External causes such as accident, abuse, misuse or problems with electrical power

supply.

(3.2) Disassembling, servicing or modification not authorized by XPOWER.

(3.3) Usage that is not accordant with product instructions stated in Owner’s Manual.

(3.4) Failure to follow the product instructions or lack of necessary maintenance stated

in Owner’s Manual.

Before contacting XPOWER, please try one or more of the following:

(1) Consult this Owner’s Manual and follow the instructions of troubleshooting guide.

(2) Access www.xpower.com for more advice and information that could be helpful to

address your problems.

If you need additional assistance from XPOWER, please:

(1) Email info@xpower.com.

(2) Call XPOWER U.S. Customer Service Department at 855-855-8868 or other numbers

provided on www.xpower.com.

(3) Visit XPOWER U.S. Head Office at 668 S. 6th Ave., City of Industry, CA 91746 or the

most current address provided on www.xpower.com.

Please also have your original proof of purchase and the serial number(s) of your

product(s) ready when you contact XPOWER.

IMPORTANT:

(1) Please finish the online warranty registration before usage. Visit www.xpower.com/

service-support/warranty-registration.

(2) This Limited Warranty applies with its own timeliness. Contact XPOWER or visit

www.xpower.com for more information.

!

English - 13

If you are instructed to return the unit for service or replacement, please:

(1) Request a RMA (Return-Merchandise-Authorization) number.

(2) Use the original or an equivalent packaging, prepay shipping charges at your own

expense to the address provided by XPOWER, with the RMA number on the shipping

label or the packaging.

(3) Include all the original parts and components.

XPOWER will inspect, assess and advise the repairs needed and applicable cost, if any.

For products under warranty, we will pay to ship the repaired or replaced product(s) to

you if you use an address within the Contiguous United States. Otherwise, we will ship

the product(s) to you at your own expense.

English - 14

English - 15

Español - 2

Instrucciones de seguridad

!ADVERTENCIA: LEA Y GUARDE ESTE MANUAL ANTES DE USAR ESTE PRODUCTO.

El usuario de productos eléctricos puede crear peligros que incluyen, pero no se limitan

a, lesiones, incendios, descargas eléctricas. El incumplimiento de estas instrucciones

puede dañar y/o perjudicar su funcionamiento y anular la garantía.

• Antes de operar, retire todo el material de embalaje y compruebe si hay algún daño que pudiera haber

ocurrido durante el envío o cualquier artículo faltante.

• Revise la fuente de alimentación para asegurarse de que coincide con las especificaciones del aparato.

• NO utilice ningún ventilador con un cable o enchufe dañado. Deseche el ventilador o devuélvalo a un

centro de servicio autorizado para su examen y/o reparación.

• Utilícelo únicamente en los tomacorrientes protegidos con interruptor de circuito de falla a tierra

(GFCI). Póngase en contacto con un electricista calificado para la verificación y / o la instalación de un

receptáculo GFCI si es necesario.

• NO coloque el cable debajo de la alfombra. NO cubra el cable con alfombras, corredores o

revestimientos similares. NO en rute el cable debajo de muebles o aparatos. Coloque el cable alejado

del área de tránsito o de paso y donde no se vaya a tropezar.

• Para reducir el riesgo de incendio o descarga eléctrica, NO utilice este aparato con ningún aparato de

control de velocidad de estado sólido.

• NO toque este aparato ni el enchufe con las manos mojadas o mientras esté parado en agua.

• NO utilice el aparato en agua estancada.

• NO utilice el producto en áreas donde se utilice o almacene gasolina, pintura u otros bienes y objetos

inflamables.

• NO inserte ni permita que objetos entren en ninguna abertura de ventilación o escape, ya que podría

dañar el aparato y anular la garantía.

• NO cubra la entrada o salida de aire del aparato.

• NO dirija el flujo de aire al rostro o cuerpo de personas.

• NO permita que los niños jueguen alrededor este aparato.

• APARATO DE FUNCIONAMIENTO AUTOMÁTICO – Para reducir el riesgo de lesiones, desconecte la

fuente de alimentación antes de realizar el mantenimiento.

• Retire el cable de alimentación del tomacorriente eléctrico agarrando y tirando solamente del extremo

del enchufe del cable de alimentación, NO tire del cable directamente.

• NO intente reparar o ajustar cualquier función eléctrica o mecánica de este aparato, ya que esto puede

resultar peligroso y anular la garantía.

• Si el aparato está dañado o funciona mal, NO continúe su uso. Desconecte el producto de la toma

eléctrica. Consulte la guía de solución de problemas o póngase en contacto con XPOWER.

• Cuando el aparato no se encuentre en uso, almacénelo en un área seca, lejos de la exposición a la luz

solar, temperatura extrema y humedad, así como de otros ambientes extremos.

• Para modelo FC-100 / FC-200 Serie, NO se debe apilar más de seis unidades de este electrodoméstico.

Para modelo FC-300 / FC-420, NO se debe apilar más de cinco unidades de este electrodoméstico.

• Se puede obtener un manual de instrucciones electrónico a través del sitio web www.xpower.com.

Español - 3

Artículos incluidos

Axial Fan Owner's Manual

XXX Manual De Usuario (página 10)

XXX Mode d'emploi (page 18)

Model / Modelo / Modèle:

P-80 Series, P-100 Series, P-200 Series

(115V 60HZ)

Read and save these instructions before use

Lea y guarde estas instrucciones antes de usar la unidad

Lire et conserver ces instructions avant utilisation

www.xpower.com | 1-(855)-8868 | [email protected]

Index: NA-1-A2

Edition: 1.0.Alpha

• Manual de usuario x 1

• Carrocería de Circulador

de Aire x 1**• Circulador de Aire x 1*

• Soporte x 1**

• Manija de Soporte x 2*

• Zapata de Goma x

2*

* Solo para modelo FC-100/FC-200 Serie/FC-420.

La apariencia exacta de los productos puede diferir ligeramente del diagrama.

** Solo para modelo FC-300 Serie.

Español - 4

Introducción del Circulador de Aire

• Los Circuladores de Aire XPOWER están

diseñados para ofrecer una circulación de aire

y una ventilación eficientes con su flujo de aire

enfocado de alta y larga distancia.

• Es perfecto para la circulación y ventilación de

aire en trabajos de limpieza / saneamiento,

control de aire acondicionado y más.

* / ** / *** / **** La función no se aplica a todos los modelos mencionados en este

manual. (Ver página 11: Especificación técnica)

Descripción de las piezas

(1) Parrilla frontal

(2) Motor

(3) Carcasa

(4) Capacitador

(5) Manija de carcasa

(6) Placa de interruptor*/

Placa de interruptor y

de temporizador**

(7) Receptáculo eléctrico

adicional *** / Placa

de temporizador ****

(8) Manija de soporte

(9) Zapata de Goma

(10) Soporte

(11) Ventilador

(12) Cubierta trasera

(13) Parrilla trasera

(14) Cable de alimentación

1

2

10

13

12

14

11

3

8

9

8

6

7

5

4

Español - 5

Instalación del soporte*

①

③

②

③

① Coloque ambas arandelas de goma en los pernos a ambos lados de la unidad.

② Alinee el bastidor con el ventilador axial.

③ Sujete la conexión con el manija de soporte.

* Solo para modelo FC-300 Serie.

Manual de instalaciones y operaciones

Placa de interruptor

OFF

1

2 3

4

Four Speed Control

OFF 5

1

2 3

4

Five Speed Control

OFF

MAX

LOW

Variable Speed Control

Control de cuatro velocidades (Solo para modelo FC-100/FC-200/FC-300 Serie)

• Gire a la posición “OFF” para apagar el soplador de aire de perfil bajo. Gire en el

sentido de las manecillas del reloj para ajustar la velocidad deseada.

• Para control de tres velocidades: El ventilador cuenta con 4 velocidades, siendo: 4, 3, 2,

1. “1” es la velocidad más baja y “4” es la velocidad más alta.

Español - 6

• Gire en el sentido de las manecillas del reloj

para ajustar el minutero encuenta regresiva

hasta que se detenga de forma automática.

• El temporizador puede ajustarse hasta a 180

minutos (3 horas).

• Cuando el minutero alcance la posición “0”, la

unidad dejará de trabajar. En la posición “ON”,

funcionará constantemente.

Placa de temporizador*

120

60

0

ON

180

* Solo para modelo FC-100/FC-200/FC-250D/FC-300/FC-420.

Placa de interruptor (Continuación)

Control de cinco velocidades (Solo para modelo FC-420)

• Gire a la posición “OFF” para apagar el soplador de aire de perfil bajo. Gire en el

sentido de las manecillas del reloj para ajustar la velocidad deseada.

• Para control de tres velocidades: El ventilador cuenta con 4 velocidades, siendo: 5, 4, 3,

2, 1. “1” es la velocidad más baja y “5” es la velocidad más alta.

Interruptor de velocidad variable (Solo para modelo FC-250D/FC-250AD)

• Gire a la posición “OFF” para apagar el purificador de aire. Gire a cualquier posición

de velocidad para encender el purificador de aire.

• Gire en el sentido de las manecillas del reloj para ajustar la velocidad deseada. “MAX”

es la velocidad más alta y “MIN” es la velocidad más baja.

* Solo para modelo FC-250AD/FC-300A.

Receptáculo eléctrico adicional*

CIRCUIT BREAKER

12A

TOTAL OUTPUT

12 AMPS MAX WITH THIS UNIT OFF

10 AMPS MAX WITH THIS UNIT ON

• Otros aparatos pueden conectarse a los

receptáculos eléctricos adicionales y

funcionar aun si el ventilador axial este

encendido o apagado. Sin embargo, el

amperaje total debe ser menor al amperaje

indicado. Modelos diferentes pueden tener

instrucciones diferentes.

• Si el ventilador axial o el aparato enchufado

deja de funcionar, presione el BOTÓN DE

REINICIO para reiniciar el circuito.

La page est en cours de chargement...

XPOWER FC-100 Mode d'emploi

Ce manuel convient également à

XPOWER FC-100 Mode d'emploi

dans d''autres langues

Documents connexes