Lennox Hearth Products LSBV-3628EN-H Manuel utilisateur

Marque: Lennox Hearth Products

Modèle: LSBV-3628EN-H

Catégorie: Cheminées

Taper: Manuel utilisateur

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Do not store or use gasoline or other flammable

vapors or liquids in the vicinity of this or any other

appliance.

What to do if you smell gas:

• DO NOT light any appliance.

• DO NOT touch any electrical switches, do not

use any phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow your gas suppliers

instructions.

• If your gas supplier cannot be reached, call the

fire department.

Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

INSTALLATION

INSTRUCTIONS

CRESTLINE™ SERIES

B-VENTED GAS APPLIANCES

P/N 850,042M REV. A 12/2008

MODELS

Millivolt Models Electronic Models

LSBV-3628MN LSBV-3628EN

LSBV-3628MP LSBV-3628EN-H

LSBV-3628MN-H LSBV-4228EN

LSBV-3628MP-H LSBV-4228EN-H

LSBV-4228MN

LSBV-4228MP

LSBV-4228MN-H

LSBV-4228MP-H

OTL Report No. 116-F-45-5

WARNING: IF THE INFORMATION IN THIS MANUAL

IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLO-

SION MAY RESULT CAUSING PROPERTY DAM-

AGE, PERSONAL INJURY OR LOSS OF LIFE.

This appliance may be installed in an aftermarket perma-

nently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes. This appliance

is only for use with the type of gas indicated on the rating

plate. This appliance is not convertible for use with other

gases, unless a certified kit is used.

In the Commonwealth of Massachusetts & New York:

• Installation must be performed by a licensed plumber or

gas fitter.

See Table of Contents for location of additional New York

& Commonwealth of Massachusetts requirements.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Portland

Ne pas entreposer ni utiliser d’essence ni d’autre

vapeurs ou liquides inflammables dans le voisinage

de cet appareil ou de tout autre appareil.

QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

•Ne pas tenter d’allumer d’appareil.

•Ne touchez à aucun interrupteur. Ne pas vous

servir des téléphones se trouvant dans le bátiment

où vous vous trouvez.

•Appelez immédiatement votre fournisseur de gaz

depuis un voisin. Suivez les instructions du

fournisseur.

•Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incendies.

L’installation et l’entretien doivent être assurés par

un installeur ou un service d’entretien qualifié ou par

le fournisseur de gaz.

INSTALLATEUR: Laissez cette notice avec l’appareil.

CONSOMMATEUR: Conservez cette notice pour

consultation ultérieure.

AVERTISSEMENT: ASSUREZ-VOUS DE BIEN SUIVRE

LES INSTRUCTIONS DONNÉES DANS CETTE NOTICE

POUR RÉDUIRE AU MINIMUM LE RISQUE D’INCENDIE

D’EXPLOSION OU POUR ÉVITER TOUT DOMMAGE

MATÉRIEL, TOUTE BLESSURE OU LA MORT.

LENNOX HEARTH PRODUCTS

A French manual is available upon request. Order P/N 506223-07.

Ce manuel d’installation est disponible en francais, simplement en faire

la demande. Numéro de la pièce 506223-07.

2NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

TABLE OF CONTENTS

Packaging........................................ page 2

Introduction..................................... page 2

Massachusetts and New York

Requirements ................................ page 2

General Information......................... page 2

Location .......................................... page 3

Appliance Specifications.................. page 4

Clearances ....................................... page 4

Gas Vent Rule.................................. page 4

Framing Specifications .................... page 5

Assembly Steps............................... page 5

Installation....................................... page 6

Vent System Installation.................. page 7

Field Wiring ..................................... page 7

Connecting Gas Line........................ page 8

Outside Air Kit Installation ............... page 8

Log and Rockwool Installation ........ page 9

Appliance Operation ........................ page 10

Manual Limit Switch........................ page 10

Millivolt Appliance Checkout............ page 11

Electronic Appliance Checkout......... page 11

Adjustments .................................... page 11

Finishing Requirements................... page 12

Cold Climate Insulation.................... page 12

Installation Accessories................... page 12

Gas Conversion Kits.................. page 14

GENERAL INFORMATION

Note: Installation and repair should be per-

formed by a qualified service person. The appli-

ance should be inspected annually by a quali-

fied professional service technician. More fre-

quent inspections and cleanings may be re-

quired due to excessive lint from carpeting,

bedding material, etc. It is imperative that the

control compartment, burners and circulating

air passage ways of the appliance be kept clean.

S'assurer que le brùleur et le compartiment des

commandes sont propres. Voir les instruc-

tions d'installation et d'utilisation qui

accompagnent l'apareil.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front openings of the appliance.

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE OR

ITS COMPONENTS. ANY MODIFICATION OR

ALTERATION MAY VOID THE WARRANTY,

CERTIFICATION AND LISTINGS OF THIS UNIT.

These appliances are designed to operate on

natural or propane gas only. The use of other fuels

or combination of fuels will degrade the perfor-

mance of this system and may be dangerous.

Input of appliance are 45,000 BTU/HR for Pro-

pane models and 50,00 BTU/HR for Natural Gas

models.

INTRODUCTION

The millivolt appliances are designed to oper-

ate on either natural or propane gas. A millivolt

gas control valve with piezo ignition system

provides safe, efficient operation.

The electronic appliances are designed to op-

erate on either natural or propane gas. An

electronic intermittent pilot system provides

safe, efficient operation. External electrical

power is required to operate these units.

These appliances comply with National Safety

Standards and are tested and listed by Omni-

Test Laboratories (Report No. 116-F-45-5) to

ANSI Z21.50b (in Canada, CSA-2.22b), and

CAN/CGA-2.17-M91 in both USA and Canada,

as vented gas fireplaces.

Installation must conform to local codes. In

the absence of local codes, installation must

comply with the current National Fuel Gas

Code, ANSI Z223.1 (NFPA 54). (In Canada, the

current CAN/CGA B149 installation code.) Elec-

trical wiring must comply with local codes. In

the absence of local codes, installation must

be in accordance with the National Electrical

Code, NFPA 70 - (latest edition). (In Canada,

the current CSA C22.1 Canadian Electric Code.)

These Crestline series appliances have been

designed, tested and listed for use with Security

Chimney's 10" B-vent system. Refer to page 12

for a complete listing of the 10" B-vent compo-

nents available for use with these models.

3 - one envelope containing the literature

package which consists of the homeowner's

manual, installation instructions, and war-

ranty; envelope is located in the control area.

WARNING: THESE FIREPLACES ARE

VENTED DECORATIVE GAS APPLIANCES.

DO NOT BURN WOOD OR OTHER MATE-

RIAL IN THESE APPLIANCES.

WARNING: IMPROPER INSTALLATION,

ADJUSTMENT, ALTERATION, SERVICE

OR MAINTENANCE CAN CAUSE INJURY

OR PROPERTY DAMAGE. REFER TO THIS

MANUAL. FOR ASSISTANCE OR ADDI-

TIONAL INFORMATION CONSULT A

QUALIFIED INSTALLER, SERVICE

AGENCY OR THE GAS SUPPLIER.

PACKAGING

The assembled vented gas fireplace is pack-

aged with:

1 - one foam packaged log set located in fire-

box area.

2 - one bag of glowing embers (rockwool)

located in the bottom compartment.

Massachusetts:

Installation of these fireplaces are approved

for installation in the US state of Massachu-

setts if the following additional requirements

are met-

• Installation and repair must be done by a

plumber or gas fitter licensed in the Common-

wealth of Massachusetts.

• The flexible gas line connector used shall not

exceed 36 inches (92 centimeters) in length.

• The individual manual shut-off must be a T-

handle type valve.

New York City, NY:

Installation of these fireplaces are approved

for installation in New York City in the US state

of New York, if the following additional re-

quirements are met-

• An outside air kit (FOAK-4 or FOAK-4LD)

must be installed.

Massachusetts And New York City, NY

Requirements

These appliances are approved for installation

in the following USA locations listed in the

following:

Gas Orifice Size

Type Elevation

0 - 4500'

(0 - 1370 m)

0 - 4500'

(0 - 1370 m)

Natural Propane

#26 #45

#45

LSBV-3628

LSBV-4228

#26

This manual is part of a set of two supporting

this product. Refer to manual 875,035M for

Care & Operations.

Please read and understand these

instructions before beginning your

installation.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Carbon Monoxide Poisoning: Early signs of

carbon monoxide poisoning are similar to the

flu with headaches, dizziness and/or nausea. If

you have these signs, obtain fresh air immedi-

ately. Turn off the gas supply to the appliance

and have it serviced by a qualified profes-

sional, as it may not be operating correctly.

In selecting the location, the aesthetic and func-

tional use of the appliance are primary concerns.

However, vent system routing to the exterior and

access to the fuel supply are also important. Due

to high temperatures the appliance should be

located out of traffic and away from furniture and

draperies. Consideration should be given to traf-

fic ways, furniture, draperies, etc., due to el-

evated surface temperatures. The location should

also be free of electrical, plumbing or other

heating/air conditioning ducting.

These appliances are equipped with an inte-

gral combustion air door and actuator arm.

Combustion air kits are optional and must be

installed before removing the securing screw

allowing the movement of the combustion

air actuator arm (see Step 7 on page 8).

Test gage connections are provided on the front

of the millivolt gas control valves (identified

OUT for the manifold side and IN for inlet

pressure side.

Minimum inlet gas pressure to the appliance is

5.0 inches water column (1.24 kPa) for natural

gas and 11 inches water column (2.74 kPa) for

propane for the purpose of input adjustment.

Maximum inlet gas supply pressure to the

appliance is 10.5 inches water column (2.61kPa)

for natural gas and 13.0 inches water column

(3.23 kPa) for propane. The appliance must

be isolated from the gas supply piping sys-

tem (by closing its individual manual shut-

off valve) during any pressure testing of the

gas supply piping system at test pressures

equal to or less than 1/2 psig (3.5) kPa).

LOCATION

Nominal operating pressures for the manifold

side of the gas control system are; 3.5 inches

water column (0.87 kPa) for natural gas mod-

els and 10 inches water column (2.49 kPa) for

propane gas models.

Do not use these appliances if any part has been

under water. Immediately call a qualified, pro-

fessional service technician to inspect the ap-

pliance and to replace any parts of the control

system and any gas control which have been

under water.

Ne pas se servir de cet appareil s'il a été plongé

dans l'eau, complètement ou en partie. Appeler

un technicien qualifié pour inspecter l'appareil et

remplacer toute partie du système de contrôle et

toute commande qui ont été plongés dans l'lau.

This appliance may be installed in an after-

market permanently located, manufactured

home (USA only) or mobile home, where not

prohibited by local codes. This appliance is

only for use with the type of gas indicated

on the rating plate. This appliance is not con-

vertible for use with other gases, unless a

certified kit is used.

Cet appareil peut être installé dans un maison

préfabriquée (É.-U. seulement) ou mobile déjà

installée à demeure si les réglements locaux

le permettent. Cet appareil doit être utilisé

uniquement avec les types de gaz indiqués

sur la plaque signalétique. Ne pas l'utiliser

avec d'autres gaz sauf si un kit de conversion

certifié est installé.

Typical Locations

Figure 1

The appliance and its individual shut-off valve

must be disconnected from the gas supply

piping system during any pressure testing of

that system at pressures in excess of 1/2 psig

(3.5 kPa).

These appliances must not be connected to a

chimney or flue serving a separate solid fuel

burning appliance.

Do not place clothing or other materials on or

near this appliance.

WARNING: CHILDREN AND ADULTS

SHOULD BE ALERTED TO THE HAZARDS

OF HIGH SURFACE TEMPERATURES. USE

CAUTION AROUND THE APPLIANCE TO

AVOID BURNS OR CLOTHING IGNITION.

YOUNG CHILDREN SHOULD BE CARE-

FULLY SUPERVISED WHEN THEY ARE IN

THE SAME ROOM AS THE APPLIANCE.

WARNING: DO NOT PLACE CLOTHING

OR OTHER FLAMMABLE MATERIALS

ON OR NEAR THIS APPLIANCE.

AVERTISSEMENT: SURVEILLER LES

ENFANTS. GARDER LES VÊTEMENTS,

LES MEUBLES, L'ESSENCE OU AUTRES

LIQUIDES À VAPEUR INFLAMMABLES

LIN DE L'APPAREIL.

WARNING: THIS APPLIANCE MAY ONLY

BE FITTED WITH DOORS CERTIFIED FOR

USE WITH THE APPLIANCE.

WARNING: FAILURE TO COMPLY WITH

THE INSTALLATION AND OPERATING IN-

STRUCTIONS PROVIDED IN THIS DOCU-

MENT WILL RESULT IN AN IMPROP-

ERLY INSTALLED AND OPERATING AP-

PLIANCE, VOIDING ITS WARRANTY. ANY

CHANGE TO THIS APPLIANCE AND/OR

ITS OPERATING CONTROLS IS DANGER-

OUS. IMPROPER INSTALLATION OR USE

OF THIS APPLIANCE CAN CAUSE SERI-

OUS INJURY OR DEATH FORM FIRE,

BURNS, EXPLOSION OR CARBON MON-

OXIDE POISONING.

WARNING: B-VENT APPLIANCES ARE

NOT DESIGNED TO OPERATE IN NEGA-

TIVELY PRESSURED ENVIRONMENTS

(PRESSURE WITHIN THE HOME IS LESS

THAN PRESSURES OUTSIDE). SIGNIFI-

CANT NEGATIVELY PRESSURED ENVI-

RONMENTS CAUSED BY WEATHER,

HOME DESIGN, OR OTHER DEVICES MAY

IMPACT THE OPERATION OF THESE AP-

PLIANCES. NEGATIVE PRESSURES MAY

RESULT IN POOR FLAME APPEARANCE,

SOOTING, DAMAGE TO PROPERTY AND/

OR SEVERE PERSONAL INJURY. DO NOT

OPERATE THESE APPLIANCES IN NEGA-

TIVELY PRESSURED ENVIRONMENTS.

4NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Venting

Gas Vent Rule – Gas vent caps are not permit-

ted within 8 feet (2.4 mm) of a vertical wall or

similar obstruction. Gas vent caps that are

located 8' or more from a portion of a building

which extends at an angle greater than 45°

upward from the horizontal may terminate in

accordance with

Table 1 (Figure 3)

, provided

that in no case shall any discharge opening on

the cap be less than 2' (610 mm) horizontally

from the roof surface (National Fuel Gas Code

ANSI Z223.1 (NFPA 54) 7.6.2) (CAN/CGA B149).

CLEARANCES

Minimum clearance to combustibles for the ap-

pliance is as follows: sides and back - 3/8" (9.52

mm), floor - 0" (0 mm), adjacent wall - 0" (0 mm),

ceiling - 37-1/2" (953 mm).

APPLIANCE SPECIFICATIONS

Figure 2 Table 1

Note: Venting terminals shall not be recessed

into a wall or siding.

Flat to 6/12 1' 0" 0.3

Over 7/12 to 9/12 2' 0" 0.6

Over 10/12 to 12/12 4' 0" 1.2

Over 13/12 to 16/12 6' 0" 1.8

Over 17/12 to 21/12 8' 0" 2.4

Roof Slope

Minimum Height

from Roof to Lowest

Discharge Opening

Feet Meters

Roof Pitch is X/12

12 X

Minimum Height from Roof

to Lowest Discharge Opening

The appliance should be mounted on a fully

supported base extending the full width and

depth of the unit. The appliance may be located

on or near conventional construction materi-

als. However, if installed on combustible mate-

rials, such as carpeting, vinyl tile, etc., a metal

or wood barrier covering the entire bottom

surface must be used.

These appliances may be used for bedroom

installations in the United States and are listed

accordingly. These units may not be installed

in bedrooms in Canada.

Figure 3

Front View

12-15/32

28-15/32 41-5/16

47-9/32

52-11/32

LSBV-36: 41-3/4

LSBV-42: 47-3/4

7-3/32

5-3/4 LSBV-36: 37

LSBV-42: 43

Left Side View

1-7/16

8-7/8

Right Side View

7-7/16

15-27/32

1-25/32

4-13/32

16-1/16 2-9/32

Top View

LSBV-36: 23-1/2

LSBV-42: 29-1/2

20-1/32

8-15/32

19/32

Gas Line

Or Switch

Wire Outlet

Gas Line

Or Switch

Wire Outlet

Combustion

Air Inlet

Junction

Box

Location

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

FRAMING SPECIFICATIONS

Figure 4

Figure 5

Figure 6

Framing Dimensions

ASSEMBLY STEPS

The typical sequence of installation follows,

however, each installation is unique resulting

in variations to those described.

1. Construct the appliance framing.

2. Route gas supply line to appliance location.

3. Position the appliance.

4. Install the vent system and exterior termina-

tion.

5. Field wire and install operating control switch.

6. Make connection to gas supply.

7. Install (optional) outside Air Kit.

8. Install the logs and rockwool.

9. Checkout appliance operation.

10. Adjust burner to ensure proper flame ap-

pearance.

PRE-INSTALLATION NOTES

The fireplace may be installed directly on a

combustible floor or raised on a platform of an

appropriate height. Do not place fireplace on

carpeting, vinyl or other soft floor coverings. It

may, however, be placed on flat wood, ply-

wood, particle board or other hard surfaces. Be

sure fireplace rests on a solid continuous floor

or platform with appropriate framing for sup-

port and so that no cold air can enter the room

from under the fireplace.

The fireplace may be positioned and then the

framing built around it, or the framing may be

constructed and the fireplace positioned into

the opening.

Usually, no special floor support is needed for

the fireplace, however, to be certain:

1. Estimate the total weight of the fireplace

system and surround materials such as brick,

stone, etc., to be installed.

2. Measure the square footage of the floor

space to be occupied by the system, surrounds

and hearth extensions.

3. Note the floor construction, i.e. 2 x 6’s, 2 x

8’s or 2 x 10’s, single or double joists, type and

thickness of floor boards.

Note: All framing dimensions calcu-

lated for 1/2" dry wall at the appliance

face. If sheathing the chase or finish-

ing with other thickness materials, cal-

culations will need to be made.

Figure 7

Fireplace Opening Width

42-1/4"

(1073 mm)

48-1/4"

(1226 mm)

52-1/2"

(1344 mm) 52-1/2"

(1344 mm)

23-9/16"

(599 mm) 29-9/16"

(751 mm)

11-1/4"

(286 mm) 14-1/4"

(362 mm)

63-1/2"

(1613 mm) 69-1/2"

(1765 mm)

LSBV-3628 LSBV-4228

31-3/4"

(807 mm)

34-3/4"

(883 mm)

20-1/2"

(521 mm) 20-1/2"

(521 mm)

(102 mm) 4"

(102 mm)

7-1/2"

(190 mm) 7-1/2"

(190 mm)

44-3/16"

(1122 mm) 49-1/8"

(1248 mm)

Corner Installation

Back Wall of Chase/Enclosure

Including Finishing Materials

if any

Rough

Framing Face

(Unfinished Shown)

FOAK-4

Combustion

Air Kit

AHH

Inside Chase

Back Wall of Chase/Enclosure

Including Finising Materials

if any

Rough

Framing Face

(Unfinished Shown)

FOAK

Combustion

Air Kit

FOAK

Combustion

Air Kit

Outside Chase

Back Wall of Chase/Enclosure

Including Finishing Materials

if any

Rough Framing Face

(Unfinished Shown)

Optional Locations

FATO Adapter

(Optional)

Header

Fireplace Framing

6NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Step 3. Position the Appliance - Slide the

fireplace into prepared framing or position fire-

place in its final position and frame later.

Refer to fireplace drawings and specifications

on pages 4 and 5 for framing dimensions and

details. Framing header may be positioned

directly on the fireplace top spacers.

IMPORTANT: UNDER NO CIRCUMSTANCES

CAN THE FIREPLACE TOP SPACERS

(refer to

FIGURE 2 )

BE REMOVED OR MODIFIED, NOR

MAY YOU NOTCH THE HEADER TO FIT

AROUND OR BE INSTALLED LOWER THAN

THE SPACERS. THE HEADER MAY BE IN DI-

RECT CONTACT WITH THE TOP SPACERS

BUT MAY NOT BE SUPPORTED BY THEM.

Fireplace should be secured to side framing

members using the full length 1/2 inch nailing

flanges that are integral to the appliance at each

side. Use 6d nails or equivalent

(Figure 9 )

All appliances are equipped with a gas flex line

and shutoff valve attached directly to the gas

control valve. To quickly and easily complete

the gas line routing, use the gas flex line kit.

4. Use this information and consult your local

building code to determine if you need addi-

tional support.

If you plan to raise the fireplace and hearth

extension, build the platform assembly then

position fireplace and hearth extension on top.

Secure the platform to the floor to prevent

possible shifting.

INSTALLING THE FIREPLACE

Step 1. Construct the Appliance Framing -

Frame appliance enclosure as illustrated in

Figures 4 through 7

on page 5.

Note: The framed depth, 20-1/2" (521 mm)

from a framed wall, must always be measured

from a finished surface. If a wall covering such

as drywall is to be attached to the rear wall, then

the 20-1/2" (521 mm) must be measured from

the drywall surface. It is important that this

dimension be exact.

If the appliance is to be elevated above floor

level, a solid continuous platform must be

constructed.

The header may rest on the top metal spacers,

but must not be notched to fit around them.

Consult all local codes.

Step 2. Route Gas Supply Line - Route gas

line

(Figure 8 )

using techniques and materi-

als prescribed by local and/or national codes.

It is recommended that a gas line of 1/2" or

greater diameter be used to allow full gas

volume to the fireplace. Undue pressure loss

will occur if the pipe is too small. The appli-

ance, as set up at the factory, is best suited

for use with a gas line routed from the left

side. The gas line may however be alternately

routed from the right side.

This unit is provided with a gas line/switch

wire outlet at both sides (see

Figure 2

). The

gas line may be routed through this opening at

either the right or left side. Route the Millivolt

switch wire through the opening opposite form

the gas line. To avoid cutting the Millivolt

switch wire, do not route the switch wire

through the opening with the gas line.

When rigid pipe is used, an ANSI approved

manual shut-off valve and union must be in-

stalled upstream of the fireplace.

IMPORTANT: HOLD GAS VALVE SECURELY

TO PREVENT MOVEMENT WHEN CONNECT-

ING TO INLET GAS LINE

An external regulator must be used on all

propane (L.P.G.) heaters to reduce the supply

tank pressure to 13" w.c. (maximum). Any

copper tubing used to supply propane (L.P.G.)

from the tank must be internally tinned.

Note: The nailing flanges and the area directly

behind the nailing tabs are exempt from the

clearances described on the fireplace clearance

label.

Figure 8

Figure 9

10-1/2"

(269 mm)

3-1/2"

(79 mm)

RIGHT

SIDE

LEFT

SIDE

7-1/4"

(184 mm)

3-1/2"

(79 mm)

WARNING: CONNECTING DIRECTLY TO

AN UNREGULATED PROPANE (L.P.G.)

TANK MAY CAUSE AN EXPLOSION.

6d Nail or

Equivalent

Ensure that a sediment trap is installed in the

existing gas line, if not, install a sediment trap

upstream to prevent moisture and contami-

nants from passing through trap to the appli-

ance controls and burners. Failure to do so

could prevent the appliance from operating

reliably.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 10

Step 4. Install the Vent System & Exterior

Termination -

Slip a 10" (254 mm) B-Vent system over the

appliance collar (

Figure 10

) and secure

with four sheetmetal screws (# 8 or larger).

Minimum overall height of the vent system

and appliance must be 12' (3.66 m) vertical

(no offset) or 17' (5.18 m) when an offset up

to 45 degrees from the vertical is used. The

lower part of the offset must not begin less

than 3' (0.914 m) above the top of the

fireplace

(see Figure 11 )

Maximum overall height of the vent system and

appliance should not exceed 40 feet (12.19m).

Figure 11

Install the B-vent system in accordance with

the vent manufacturer's instructions.

CAUTION: THIS APPLIANCE CANNOT BE

VENTED HORIZONTALLY.

Note: Refer to the vent manufacturers installa-

tion instructions for variations of venting tech-

niques. If common venting of several units is

contemplated, it should be discussed with an

architect and the local Building Department.

Step 5. Field Wiring – Refer to Section A for

millivolt appliances and Section B for electronic

appliances.

A. Millivolt Wiring – Units are fitted at the

factory with an SIT millivolt gas control valve.

The valve has been tested with and approved

for use with these appliances and is listed

accordingly. Refer to

Figure 12

for the wiring

diagram.

12 ft.

Minimum 17 ft.

Minimum

45 degrees

max.

3 ft.

Minimum

to Offset

The gas valve has been set in place and has been

pre-wired at the factory. Locate the wall switch

(not provided) or optional remote control in the

desired location and connect the millivolt wire

(see Figure 12 ).

CAUTION: DO NOT CONNECT THE WALL

SWITCH TO A 120V POWER SUPPLY.

Note: The ends of the 18' coiled wire must be

connected to the wall switch (not supplied) for

the appliance to operate.

B. Electronic Wiring – The electronic appli-

ance must be connected to the main power

supply. To install, route a 3-wire 120V 60Hz

power supply to the appliance junction box

and ground.

IMPORTANT: Ground lead must be con-

nected to the green screw located on

the outlet box. See

Figure 16

on page 9.

Failure to do so will result in a potential

safety hazard. The appliance must be

electrically grounded in accordance with

local codes or, in the absence of local

codes, the National Electrical Code,

ANSI/NFPA 70-(latest edition). (In

Canada, the current CSA C22-1 Cana-

dian Electrical Code.)

Figure 12

BLACK BLACK

DAMPER SWITCH LIMIT SWITCH

MILIVOLT WIRING DIAGRAM

TP TP TH

THERMOPILE

WALL MOUNTED

ON/OFF SWITCH

GAS VALVE

BLACK

WHITE

10”

Type B-Vent

Flue Outlet

Collar

Securing

Screws

Locate and install a low voltage (24V) wall

switch (not supplied) in the desired location.

Connect the low voltage wire to this switch

(

see Figure 13

on Page 8)

8NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 14

1. Route a 3-wire 120V 60Hz power supply line

to the appliance junction box wires and ground

(Figures 13 ).

2. After wiring is complete, replace the appli-

ance junction box cover and secure with the hex

head screws previously removed.

Step 6. Connecting Gas Line – Make gas line

connections. All codes require a shut-off

valve mounted in the supply line.

Figure 16

on page 9

illustrates the method for con-

necting the gas supply. The flex-line method

utilizing the gas flex line provided with the

appliance is acceptable in the U.S., how-

ever, Canadian requirements vary depend-

ing on locality. Installation must be in com-

pliance with local codes.

The gas control valve is located in the lower

control compartment. To access the valve

remove the refractory access panel and set

aside

(Figure 14 ).

The control valve has a

3/8" (10 mm) NPT thread inlet port.

Secure all joints tightly using appropriate

tools and sealing compounds (ensure pro-

pane resistant compounds are used in pro-

pane applications).

Turn on gas supply and test for gas leaks,

using a gas leak test solution (also referred to

as bubble leak solution).

Refractory

Access Panel

SIT Valve

Shown

Note: Using a soapy water solution (50% dish

soap, 50% water) is an effective leak test

solution but it is not recommended, because

the soap residue that is left on the pipes/

fittings can result in corrosion over time. Never

use an open flame to check for leaks.

A. Light the appliance (refer to the lighting

instructions label in the control compartment

or in the Homeowner's Care and Operation

Instructions).

B. Brush all joints and connections with the

gas leak test solution to check for leaks. If

bubbles are formed, or gas odor is detected,

turn the gas control knob to the “OFF” posi-

tion. Either tighten or refasten the leaking

connection and retest as described above.

C. When the gas lines are tested and leak free,

be sure to rinse off the leak testing solution.

Step 7. Optional Outside Air Kits – Combus-

tion (outside make-up air) kits, Model FOAK-4

or FAOK-4LD, may used with these appli-

ances. Refer to the installation instructions

packaged with the air kits for specific installa-

tion information. The outside air kit must be

installed before the fireplace is framed and

enclosed in the finished wall.

Outside air drawn into the fireplace supplies

air to the fire for combustion. Only one com-

bustion air duct on the right side of the fire-

place is necessary if installed.

If additional length of duct is necessary, pur-

chase locally available U.L. Class 0 or Class 1

metallic ducting. The duct may extend up to

50' (15.24 m) in any direction.

There is one hand operated air gate shut-off,

for utside make-up air, located at the right side

of the fireplace opening behind the screen. To

open, lift and pull the handle out. The combus-

tion air damper should be

open when the

fireplace is in use

and, to prevent outside air

from entering your home, fully closed when

the fireplace is not in operation.

WHITE

DAMPER SWITCH LIMIT SWITCH

CONNECTOR

BLACK BLACK

ELECTRONIC WIRING DIAGRAM

24 V.

TRANSF

120 V.

ELECTRONIC IGNITION

CONTROL BOARD

WALL MOUNTED

ON/OFF SWITCH

PILOT BURNER

IGNITER-SENSOR

ASSEMBLY

GAS VALVE

EV2 EV1

GROUND

CONNECTOR

GREEN LED

WHITE

ORANGE

BLACK

PURPLE

GREEN

BLUE

BLACK

WHITE

Junction Box

White

Green

Red

Black

Neutral

Side of

Receptacle

Green

Ground

Screw Hot

Side of

Receptacle

Ta b

Broken

Plug blower

into this

receptacle

Tab Intact

120 VAC - Black

G-dn

lar

Figure 13

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 15

Note: Supply wires may be alternatively connected to the outlet using the screw terminals, however

the black supply wire must be wired to a terminal that is opposite (across the outlet) the point where

the white supply wire is connected (Figure 15 ).

Figure 16

CAUTION: NEVER LOCATE INLET OF AN OUT-

SIDE AIR HOOD WHERE IT CAN BE BLOCKED

BY SHRUBS, SNOW DRIFTS, ETC. NEVER

LOCATE INLET IN GARAGE OR ANY AREA

WHERE THERE IS ANOTHER FUEL BURNING

APPLIANCE OR PRODUCTS EMITTING COM-

BUSTIBLE GASES SUCH AS PAINT, GASO-

LINE, ETC. IN COLD CLIMATES, IT IS REC-

OMMENDED THE COMBUSTION AIR DUCT BE

INSULATED.

Outside combustion air ducting may be run

upwards or vertically through framing and

ceiling joists, with the hood installed through

an outside wall and 3' (1 m) below the termi-

nation. Ducting may also be run downward

through floor joists and under the home to a

ventilated crawlspace not considered part of

the living area of the home.

After installing the outside air kit, remove the

cover from the shut off lever in the left side of

the firebox opening.

Note: Do not terminate combustion air kit in

attic space under any circumstances.

After completing the installation of the op-

tional combustion air vent system the actuator

arm must be put in service and tested to

ensure proper operation before completing

any enclosure around the firebox. Failure to do

so may result in extensive and costly rework.

Operate the actuator through several cycles

including the closed position. Ensuring proper

operation and freedom of movement. Return

the actuator arm to the closed position.

Step 8. Installing Logs and Rockwool – The

logs are packaged within the firebox. Remove

the rockwool from the packaging and tear into

dime size pieces (see Homeowners Care and

Operation Instructions). Do not use more than

is necessary.

Displace Lava Rock to the center of the burner

pan when removing and reinstalling the burner

tube.

1/2" x 3/8" Flare

Shut-Off Valve

3/8" Flex Tubing

Gas Flex Line (provided)

Gas Stub

3/8" NPT Flare

Fitting (Remove

Before Hard Piping)

Gas Valve

(Millivolt or Electronic)

White

(Supply)

Black

(Supply)

Bipolar

Terminal

Screw

120 Vac

60 Hz

Green Wire Ground

Connection

Red

(Supply)

120 Vac

60 Hz

120 Vac

60 Hz

10 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 17

Figure 18

Refer to the Homeowners Care and Operation

Instructions for detailed log description and

placement instructions. Log set shown in this

document

(Figure 17 )

is typical, installation

of all sets are similar.

APPLIANCE OPERATION

Step 9. Checking the System – With gas line

installed run initial system checkout before

closing up the front of the unit. Follow the pilot

lighting instructions provided in the

Homeowner's Care and Operation Instructions.

For piezo ignitor location see

Figure 18

(mil-

livolt appliances only).

Note: Instructions are also found on the pull

out lighting instructions label attached to the

gas control valve.

When first lighting the appliance, it will take a

few minutes for the line to purge itself of air.

Once purging is complete, the pilot and burner

will light and operate as indicated in the in-

struction manual.

MANUALLY-RESET BLOCKED FLUE SAFETY

SWITCH

This appliance is equipped with a manually-

reset blocked flue safety switch. Refer to

Figure 19

for its location. If during appliance

operation, the flame goes out (independently

of the burner on/off wall switch), it may be due

to the operation of this safety limit switch.

First allow the appliance to cool. Then reset

the safety switch by pushing the red reset

button.

This reset button is located on the back of the

limit switch, between the wire terminals (

see

Detail A of Figure 19

The appliance should then relight and remain

lit. If this does not occur, turn off the appli-

ance and call a qualified service technician.

Figure 19

Detail A

Manual Reset

Limit Switch

Lintel

Extension Right Side

Refractory Panel

Reset

Button

Wire

Terminals

Subsequent lightings of the appliance will

not require such purging. Inspect the pilot

flame (remove logs, if necessary, handling

carefully).

Piezo

Ignitor

SIT Valve

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 22

Adjustment

To adjust the flame, position the air shutter to

the nominal setting

(Figure 22 ).

Allow the

burner to operate for at least 30 minutes.

Observe the flame continuously. If it appears

weak or sooty as previously described, adjust

the air shutter open or closed until desired

effect is achieved.

Note: If the flame still appears anemic with the

air shutter closed all the way (usually a result of

lengthy vertical venting runs), turn off the appli-

ance, turn off the gas supply, wait for the parts

to cool and access the air shutter. The shutter

is prevented from actually closing by a tab that

is bent over into the opening. Remove this

obstruction by bending back. Reassemble and

restart the appliance and after 24 minutes

reobserve the flame. Adjust the air shutter as

described.

Figure 21

Replace logs if removed for pilot inspection.

To light the burner; rotate the gas valve control

knob counterclockwise to the “ON” position

(“ON” will be to the right hand side of the valve).

Turn “ON” the remote wall switch.

Electronic Appliance Checkout

To light the burner, turn ‘ON’ the optional

remote wall switch. Ensure the ignitor lights

the pilot. The pilot flame should engulf the

flame rod as shown in

Figure 21.

Step 10. Adjustments – The following para-

graphs address adjustment concerns and pro-

cedures.

Flame Appearance and Sooting

Proper flame appearance is a matter of taste.

Generally most people prefer the warm glow of

a yellow to orange flame. Appliances operated

with air shutter openings that are too large, or

with long vertical vent runs, will exhibit flames

that are blue and transparent. These weak, blue

and transparent flames are termed anemic.

If the air shutter opening is too small sooting

may develop. Sooting is indicated by black

puffs developing at the tips of very long orange

flames. Sooting results in black deposits form-

ing on the logs, appliance inside surfaces and

on exterior surfaces adjacent to the vent termi-

nation. Sooting is caused by incomplete com-

bustion in the flames and a lack of combustion

air entering the air shutter opening.

To achieve a warm yellow to orange flame with

an orange body that does not soot, the shutter

opening must be adjusted between these two

extremes.

No smoke or soot should be present. Reposi-

tion the log set if the flames impinge on any of

them.

If sooting conditions exist, the air shutter

opening on the main burner can be adjusted.

Normally, the more offsets in the vent system,

the greater the need for the air shutter to be

opened further.

Figure 20

When satisfied that the appliance operates prop-

erly, proceed to finish the installation. Leave the

control knob/lever in “ON” position and turn the

remote switch “OFF.” Replace the refractory

access panel.

Millivolt Appliance Checkout

The pilot flame should be steady, not lifting or

floating. Flame should be blue in color with

traces of orange at the outer edge.

The top 3/8" (9 mm) at the pilot generator

(thermopile) should be engulfed in the pilot

flame. The flame should project 1" (25 mm)

beyond the hood at all three ports

(Figure 20 ).

3/8

" Min

(9 mm)

Hood

Pilot

Nozzels

Ignitor Rod

WARNING: AIR SHUTTER ADJUSTMENT

SHOULD ONLY BE PERFORMED BY A

QUALIFIED PROFESSIONAL SERVICE

TECHNICIAN.

Factory Air

Models Shutter Setting

Inches (mm)

LSBV-3628

Gas

Type

Natural 1/8" (3.175 mm)

Propane 1/2" (12.7 mm)

LSBV-4228 Natural 1/8" (3.175 mm)

Propane 1/2" (12.7 mm)

Hood Ignitor Rod

Pilot

Nozzels

Flame

Sensor

Orifice

Air Shutter

Burner Tube

Adjusting

Set Screw

12 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

INSTALLATION ACCESSORIES

The following accessory items are available for

use in the installation of this appliance.

Figure 24

COLD CLIMATE INSULATION

If you live in a cold climate, seal all cracks

around your appliance with noncombustible

material and wherever cold air could enter the

room. It is especially important to insulate

outside chase cavity between studs and under

floor on which appliance rests, if floor is above

ground level.

60"

(1524 mm)

Min. to

Ceiling

12" Min.

(305 mm)

0" Clearance

to Combustible

Side Wall

Max. Projection 12" (305 mm)

Combustible

Mantel

Figure 23

FINISHING REQUIREMENTS

Wall Details and Combustible Mantels

Complete finished interior wall. To install the

appliance facing flush with the finished wall,

position framework to accommodate the thick-

ness of the finished wall

(Figure 23 )

. Both

Figures 23 and 24

show a combustible mantel

shelf projecting a maximum of 12" (305 mm)

from the wall, and which must be installed a

minimum distance of 12" (305mm) from the

top of the firebox opening. No other mantel

length/height combinations are allowable for

this fireplace.

A hearth extension is not required with this

appliance. Any hearth extension used is for

appearance only and does not have to conform

to standard hearth extension installation re-

quirements.

Note: Combustible wall finish materials and/or

surround materials must not be allowed to

encroach the area defined by the appliance

front face (black sheet metal). Never allow

combustible materials to be positioned in front

of or overlapping the appliance front face.

Elbow 10" X 45 Degree 10KE45

Firestop BV 10" 10KBF

12" Length 10KL1

24" Length 10KL2

36" Length 10KL3

Security 10" B-vent Adjustable Length 10KAL

Brace Support BV 10" 10KBS

Fireplace Opening

Typical Installation

10"

Min.

12"

Min.

18"

12"

Max.

Combustible

Mantel and Trim

(See Note)

3 Sheet Metal Screws

#10 x 3/4" Max. Flat Head

5" Top Of Fireplace

Non

Combustible

Material Sheet Metal

Spacer

Finished Wall

Header

Note: Mantel At Minimum Height Should Be Affixed to Framing Hinge Posts At Right

And Left Of The Fireplace. Do Not Use Molly Bolts In Front Of The Fireplace.

18 5/8"

Non-Combustible Material

1-3/8"

11-3/8"

Min.

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Wall Switch Kit 85L87 FWSK

Outside Combustion Air Kits

(with duct) 81L87 FOAK-4

(without duct) 81L88 FOAK-4LD

Outside Air Kits Models FOAK-4 and FOAK-4LD

Outside Air kits are available with duct

(FOAK-4) and without duct (FOAK-4LD)

for use if outside combustion air is re-

quired or desired. If model FOAK-4LD is

used it must be used in conjunction with

locally purchased, non-combustible Class

1 or Class 0 flexible duct.

Storm Collar BV 10" 10KFC

Adjustable Flashing 1/12 - 7/12 10FA

10" Gas Vent 17/12 - 12/12 10FB

INSTALLATION ACCESSORIES

CONTINUED

Rain Cap B-Vent 10KCGV

Roof Brace XBS2

Anchor Plate 10SP

Radiation Shield 10RS

Flat Roof Flashing

With Storm Collar 10KF

Following Components Are Not Illustrated

Chase Top Shroud Kits

(Arch Top 3 x 3) H1988 CTSA-33

(Open Top 3 x 3) H1985 CTS0-33

(Open Top 4 x 4) H1987 CTSO-44

(Open Top 4 x 6) H1986 CTS0-46

14 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 25

Pressure

Regulator

Remove

These

Components

Step 1. Turn off the gas supply to the appli-

ance. Remove the front glass door (if used)

from the appliance. Access the control com-

partment.

Step 2. Carefully remove the logs. Exercise

care as not to break the logs.

Step 3. Locate the screw securing the burner.

Remove the burner and retain the securing

screw.

Millivolt Appliances

Step 4. SIT Systems - Refer to

Figure 25

and

the instructions provided with the kit. Using a

Torx T20, remove and discard the three pres-

sure regulator mounting screws.

Remove the pressure regulator, spring, pop-

pet, diaphragm and bushing. Discard all re-

moved components. Ensure the rubber gasket

installed on the back of the replacement pres-

sure regulator is properly positioned and install

the new pressure regulator using the new screws

supplied with the kit. Tighten screws to 25 In.

lb. torque.

Gas Conversion Kits

In Canada

THE CONVERSION SHALL BE CARRIED OUT

IN ACCORDANCE WITH THE REQUIREMENTS

OF THE PROVINCIAL AUTHORITIES HAVING

JURISDICTION AND IN ACCORDANCE WITH

THE REQUIREMENTS OF THE CAN1-B149.1

AND .2 INSTALLATION CODE.

LA CONVERSION DEVRA ÊTRE EFFECTUÉE

CONFORMÉMENT AUX RECOMMANDATIONS

DES AUTORITÉS PROVINCIALES AYANT

JURIDICTION ET CONFORMÉMENT AUX

EXIGENCES DU CODE D'INSTALLATION CAN1-

B149.1 ET.2.

Gas conversion kits are available to adapt your

appliance from the use of one type of gas to the

use of another. These kits contain all the nec-

essary components needed to complete the

task including labeling that must be affixed to

ensure safe operation.

Kit part numbers are listed here and the steps

that follow detail the conversion procedure.

WARNING: THIS CONVERSION KIT SHALL BE IN-

STALLED BY A QUALIFIED SERVICE AGENCY IN AC-

CORDANCE WITH THE MANUFACTURER'S INSTRUC-

TIONS AND ALL APPLICABLE CODES AND REQUIRE-

MENTS OF THE AUTHORIZED AGENCY HAVING JU-

RISDICTION. IF THE INFORMATION IN THESE IN-

STRUCTIONS ARE NOT FOLLOWED EXACTLY, A FIRE,

EXPLOSION OR PRODUCTION OF CARBON MONOX-

IDE MAY RESULT CAUSING PROPERTY DAMAGE,

PERSONAL INJURY OR LOSS OF LIFE. THE INSTAL-

LATION IS NOT PROPER AND COMPLETE UNTIL THE

OPERATION OF THE CONVERTED APPLIANCE IS

CHECKED AS SPECIFIED IN THE OWNER INSTRUC-

TIONS SUPPLIED WITH THE KIT.

AVERTISSEMENT: CET ÉQUIPEMENT DE CONVERSION

SERA INSTALLÉ PAR UNE AGENCE QUALIFIÉE DE SERVICE

CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT ET

TOUTES EXIGENCES ET CODES APPLICABLES DE

L'AUTORISÉS AVOIR LA JURIDICTION. SI L'INFORMATION

DANS CETTE INSTRUCTION N'EST PAS SUIVIE

EXACTEMENT, UN FEU, EXPLOSION OU PRODUCTION DE

PROTOXYDE DE CARBONE PEUT RÉSULTER LE DOMMAGES

CAUSER DE PROPRIÉTÉ, PERTE OU BLESSURE

PERSONNELLE DE VIE. L'AGENCE QUALIFIÉE DE SERVICE

EST ESPONSABLE DE L'INSTALLATION PROPRE DE CET

ÉQUIPMENT. L'INSTALLATION N'EST PAS PROPRE ET

COMPLÉTE JUSQU'À L'OPÉRATION DE L'APPAREIL

CONVERTI EST CHÉQUE SUIVANT LES CRITÈRES ÉTABLIS

DANS LES INSTRUCTIONS DE PROPRIÉTAIRE

PROVISIONNÉES AVEC L'ÉQUIPEMENT.

-smetsySTIStlovilliM stiKnoisrevnoCsaGenaporPoTlarutaN

sledoMepyTtinU.oNgolataC

8263-VBSL tlovillim4185H

8224-VBSL tlovillim4185H

-smetsySTIStlovilliM stiKnoisrevnoCsaGlarutaNotenaporP

sledoMepyTtinU.oNgolataC

8263-VBSL tlovillim2185H

8224-VBSL tlovillim2185H

-smetsySTIScinortcelE stiKnoisrevnoCsaGenaporPoTlarutaN

sledoMepyTtinU.oNgolataC

8263-VBSL cinortcele5185H

8224-VBSL cinortcele5185H

-smetsySTIScinortcelE stiKnoisrevnoCsaGlarutaNotenaporP

sledoMepyTtinU.oNgolataC

8263-VBSL cinortcele3185H

8224-VBSL cinortcele3185H

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Figure 28

Figure 29

Step 9. Reassemble all removed components

by reversing the procedures outlined in the

preceding steps. Use pipe joint compound or

Teflon tape on all pipe fittings before installing

(ensure propane resistant compounds are used

in propane applications, do not use pipe joint

compounds on flare fittings).

Step 10. Attach the conversion label provided

in the conversion kit to the rating plate on the

appliance.

Step 11. Turn on gas supply and test for gas

leaks. (See

step 6

on page 8.)

Figure 27

Step 5. Millivolt Systems – Attach manom-

eter to the manifold side pressure test fitting

and verify manifold pressure reads 3.5 inches

water column (0.87 kPa) for natural gas, and

10.0 inches water column (2.49 kPa) for pro-

pane gas.

Step 6. See

Figure 26

and remove the pilot

hood assembly to access the hexed pilot ori-

fice. Remove and replace the orifice with the

one provided with the kit.

When reinstalling the ignitor assembly, use

extreme care to prevent damage and break-

age. Do not apply any leverage to the ignitor

assembly while restoring the retainer clip to

its original position.

All Models

Step 8. Unscrew the orifice from the manifold

and replace it with the one provided with the

kit

See the following table for orifice sizes for

natural and propane models.

Figure 29

illus-

trates the orifice.

Refer to

Figure 27

and replace the pilot orifice

as follows: Remove the pilot hood assemble

to access the hexed polot ofifice.

Remove the pilot orifice and replace it with the

one provided with the conversion kit. Reinstall

the pilot assembly by reversing the steps de-

tailed here.

Figure 26

Pilot

Orifice

Pilot

Orifice

LSBV

Series Natural Propane

Orifice Size

3628 #26 #45

4228 #26 #45

Electronic Appliances

Step 7. SIT Electronic Valves - See

Figure 28

and the instructions provided with the kit.

Remove the slotted cap screw, o-ring, pres-

sure-regulating adjusting screw and spring,

then discard.

Modify the pressure regulator from the kit.

Using a standard tin snip cutting tool, proceed

to trim shoulder off of the regulator.

Install new components and modified pres-

sure regulator from the kit.

Attach manometer to the manifold side pres-

sure test fitting and adjust screw until pres-

sure reads 3.5 inches water column (0.87 kPa)

for natural gas, and 10.0 inches water column

(2.49 kPa) for propane gas.

Modified Kit

Pressure Regulator

- After Trim

Remove

These

Components

SIT VALVE

Kit Pressure

Regulator - Before

Trim

16 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

Lennox Hearth Products reserves the right to make changes at any time, without notice, in design,

materials, specifications, prices and also to discontinue colors, styles and products.

Consult your local distributor for fireplace code information.

P/N 850,042M REV. A 12/2008 1110 West Taft Avenue • Orange, CA 92865

Lennox Hearth Products LSBV-3628EN-H Manuel utilisateur

Marque: Lennox Hearth Products

Modèle: LSBV-3628EN-H

Catégorie: Cheminées

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Lennox Hearth Products LSBV-3628EN-H User manual

Lennox Hearth Products LSBV-3628EN-H Manuel utilisateur

Lennox Hearth Products LSBV-3628EN-H Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents