ReVent RVL50 Guide d'installation

Installation Guide

Read and Save These Instructions

Watch the installation videos at:

reventfans.com and

reventfans.com/how-to-remove-an-old-bath-fan

Questions? Call

1-877-543-8698 (English) or

1-800-615-5439 (French)

model

RVL50, RVL70

Need Help?

English

1

Table of Contents

Please Read and Save

These Instructions

page 1

page 1-2

page 3

page 4

page 5

page 6

page 7-9

page 10-16

page 16-21

page 21

page 21-22

page 23

Table of Contents

Specifications

What’s Inside The Box

Safety Information

Planning Your Installation

Connecting The Duct

Removing Your Old Fan

SheetLock® Easy Roomside Installation

Installation For New Construction Framing

Care And Cleaning

Frequently Asked Questions

3-Year Limited Warranty

...............

............

...............

............

........

.............

........

.............

Specifications

RVL50

performance at 4" and 3" ducting

Duct

Size

4 in

3 in

Energy

(watts)

5.9

7.5

5.5

7.4

Static Pressure

(in wg)

0.1

0.25

0.1

0.25

Airow

(cfm)

50

41

50

42

Sound

(sones)

0.5

0.7

0.5

1.2

2

Voltage

Frequency

LED Watts

LED Brightness

LED Color Temp

Fan Weight

Shield Size

Housing Length*

Housing Width*

Housing Depth*

120 V

60 Hz

13 W

900, 1000, or 1000 Lumens

2700, 4000, or 5000 Kelvin

4.0 Lbs. ( 1.8 Kg )

9 3/4 x 9 3/4 in ( 24.8 x 24.8 cm )

7 1/4 in ( 18.4 cm )

7 1/2 in ( 19.1 cm )

4 3/8 in ( 11.1 cm )

*This may require modification of your current opening. Some hand

tools required. Power tools may also be necessary.

RVL70

Voltage

Frequency

LED Watts

LED Brightness

LED Color Temp

Fan Weight

Shield Size

Housing Length*

Housing Width*

Housing Depth*

120 V

60 Hz

13 W

900, 1000, or 1000 Lumens

2700, 4000, or 5000 Kelvin

4.0 Lbs. ( 1.8 Kg )

9 3/4 x 9 3/4 in ( 24.8 x 24.8 cm )

7 1/4 in ( 18.4 cm )

7 1/2 in ( 19.1 cm )

4 3/8 in ( 11.1 cm )

*This may require modification of your current opening. Some hand

tools required. Power tools may also be necessary.

performance at 4" and 3" ducting

Duct

Size

4 in

3 in

Energy

(watts)

7.9

11.1

10.9

9.7

Static Pressure

(in wg)

0.1

0.25

0.1

0.25

Airow

(cfm)

70

60

45

Sound

(sones)

0.9

1.3

3

What’s Inside The Box

FAN

Qty:1

4” DAMPER

Qty:1

SHIELD

Qty:1

MANUAL

Qty:1

TEMPLATE

Qty:1

TRIM RING

Qty:1

4 TO 3 IN

DUCT ADAPTER

Qty:1

WIRE NUT

Qty:4

ROUNDHEAD

WOOD SCREW

Qty:4

USED FOR NEW CONSTRUCTION ONLY

Installation Guide

Read and Save These Instructions

Watch the installation videos at:

reventfans.com and

reventfans.com/how-to-remove-an-old-bath-fan

Questions? Call

1-877-543-8698 (English) or

1-800-615-5439 (French)

model

RVL50, RVL70

Need Help?

English

4

Safety Information

1.) WARNING - TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,

OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a) Installation work and electrical wiring must be done by qualified person(s) in

accordance with all applicable codes and standards, including fire-rated

construction.

b) Sufficient air is needed for proper combustion and exhausting of gases

through the flue (chimney) of fuel burning equipment to prevent back drafting.

Follow the heating equipment manufacturer's guideline and safety standards,

such as those published by the National Fire Protection Association (NFPA), the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

c) When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

d) Ducted fans must always be vented to the outdoors.

e) If this unit is to be installed over a tub or shower, it must be marked as

appropriate for the application and be connected to a GFCI (Ground Fault Circuit

Interrupter) - protected branch circuit.

2.) Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer.

3.) Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

4.) This ventilation fan is approved for use over a bathtub or shower when installed

in a GFCI protected circuit. Do not use unapproved fans over a bathtub or shower

that are not approved for that application.

5.) Install ductwork in a straight line with minimal bends.

6.) Use 120 V, 60 Hz for the electrical supply and properly ground the unit. Follow

all local safety and electrical codes.

7.) Do not use this fan with any solid-state control device; such as a dimmer switch.

Solid-state controls may cause harmonic distortion, which can cause a motor

humming noise, as well as increase risk of fire or electric shock.

8.) To reduce the risk of fire or electric shock, do not block air entry shield.

9.) Mount with the lowest moving parts at least 8.2 ft (2.5 m) above floor or grade

level.

10.) Never place a switch where it can be reached from a tub or shower.

11.) Type IC for use in direct contact with thermal insulation not to exceed R-50.

12.) Not for use in cooking areas. (See PAGE 5 for details)

13.) This product must properly connect to the grounding conductor of the supply

circuit.

Follow the heating equipment manufacturer’s guideline and safety standards, such

as those published by the National Fire Protection Association (NFPA), the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

WARNING: Not suitable for use as a range hood.

CAUTION: For General Ventilating Use Only - Do Not Use To Exhaust

Hazardous Or Explosive Materials And Vapors.

CAUTION: Do not install in locations where the temperature will exceed

104°F (40°C).

IMPORTANT: Exercise care to not damage existing wiring when cutting or

drilling into walls or ceilings.

NOTE: Make sure duct work size is a minimum of the discharge. Do not

reduce. Reducing the duct size can increase fan noise.

IMPORTANT: You may want to consult with a qualified licensed electrician

regarding the wiring of your ventilation fan.

WARNING: To reduce the risk of electric shock, please disconnect the

electrical supply circuit before servicing.

CAUTION: This product must be properly grounded.

Go to reventfans.com to obtain a copy of this manual.

5

NOTE: If installing in existing construction, you may need to have access to

space above and below the installation location.

Cooking Area

do not install above or

inside this area

Cooking

Equipment Floor

Turning angle too sharp

Too many elbows

Avoid duct shrink

Elbow near the body

Fan

Body

Minimum 18 in ( 45.72 cm )

Planning Your Installation

When installing the ventilation fan in a new construction site, install the main body

of the FAN and duct work during the rough-in construction of the building. The

SHIELD should be installed after the finished ceiling is in place.

When installing in existing construction, use the provided cutout TEMPLATE for the

ceiling. SHIELD edge should overlap finished ceiling.

Not for use in cooking area - see diagram below.

Do not install ventilation fan in areas where the duct work will require configuration

as shown.

There are multiple installation configurations possible for this ventilation fan. Not all

configurations are shown. If your installation requires a variation other than those

shown, consult with a licensed contractor to determine the best installation for your

project. If you are replacing an existing fan, ensure that the new FAN will

adequately cover the existing opening.

6

Connecting the Duct

● Install a circular duct to outlet and secure it with duct tape or clamps.

● Install the duct to the outlet with a gradient 1°~2° to the outside as shown.

● The ducting from this FAN to the outside of the building has a strong effect on

● the air flow, noise and energy use of the fan. Use the shortest, straightest duct

● routing possible for best performance, and avoid installing the FAN with smaller

● ducts than recommended. Insulation around the ducts can reduce energy loss

● and inhibit mold growth. Fans installed with existing ducts may not achieve their

● rated airflow.

● For models RVL50 or RVL70, 4 in (10.16 cm) round is recommended for

● best performance.

● Ensure duct joints and exterior penetrations are sealed with caulk or other

● similar material to create an air-tight path, to minimize building heat loss and

● gain, and to reduce the potential for condensation.

● Place/wrap insulation around duct and/or FAN in order to minimize possible

● condensation buildup within the duct, building heat loss and gain.

INSULATION*

(Place around and

over Fan Housing.)

Seal gaps

around

housing.

ROUND

DUCT*

POWER

CABLE*

Seal duct

joints with

tape.

FAN

HOUSING

ROUND

ELBOWS*

ROOF CAP*

(with built-in

damper)

Keep duct

runs short.

WALL CAP*

(with built-in

damper)

*Purchase

separately.

OR

7

Removing An Old Fan

Watch the video: reventfans.com/how-to-remove-an-old-bath-fan

1.) Disconnect the electrical power supply and lock out the service

panel for the existing fan.

2.) Remove the grille from the existing fan. Pull the grille down to expose it’s two

springs. Squeeze each spring together and pull down again to release the springs

from the motor plate slots.

3.) Unplug the fan motor.

4.) Loosen the motor plate by inserting a flathead screwdriver into the slot in the

housing and twisting the screwdriver.

Pry loose with flat head

screwdriver if needed

springs

grille

ceiling

fan motor

8

6.) Open or remove the electrical box and disconnect all wiring.

7.) Grab the fan housing with plyers and bend the fan housing inward to expose

the screws that mount the fan to the joist. Remove the screws or slide them

through the slots on the joist mounts.

5.) Remove the motor from the fan housing.

grab fan housing

with plyers

fan housing

motor

electrical box

disconnect

all wiring

fan housing

bend the fan housing

inward to expose the

screws

fan housing

9

8.) Raise the housing into the ceiling. Pull the wiring out of the fan housing.

Remove the tape from the vent pipe and disconnect.

9.) Remove the fan housing from the ceiling.

expose and remove

the screws that mount

the fan to the joist

fan housing

pull the wiring out

of the fan housing

ceiling

fan housing

10

1.) Place the provided sheetrock cutout TEMPLATE on ceiling where you wish the

FAN to be (DAMPER and electrical positions shown on TEMPLATE). We suggest

using painter’s masking tape to hold the template in place while cutting. If there is a

pre-existing fan opening, use aligning windows to find it’s edges. Either cut through

the provided guide slots in the TEMPLATE, or mark your cut lines with a pencil and

remove the TEMPLATE. Use a sheetrock jab saw to cut your fan opening in the

ceiling. Note: Measure the opening from your old fan. ReVent® RVL50 or RVL70 fit

most openings without cutting.

SheetLock® Easy Roomside

Installation

Watch the video: reventfans.com

WARNING: Disconnect all AC Power Breakers or Fuses before attempting

to cut into your ceiling.

3.) Raise then slide the DAMPER up half way until the notch in the side of the

DAMPER aligns with the upper set of guides. Remove the DAMPER from the FAN.

Remove

DAMPER

from FAN

at notch

FAN

DAMPER

TEMPLATE

sheetrock jab saw

2.) Fold in ceiling joist mounts so that they’re flush with the FAN housing.

FAN

ceiling joist mount

fold ceiling joist

mounts flush with FAN

11

4.) Set the FAN in the ceiling opening, then attach conduit with wiring to FAN.

conduit

FAN

6.) Reattach DAMPER to FAN inside the ceiling, damper should click into place

securely.

ducting

conduit

DAMPER

FAN

5.) Attach DAMPER to ducting. Tape DAMPER to ducting with duct tape. Set the

connected DAMPER and ducting in the ceiling opening.

ceiling

4 in ducting

Connect DAMPER and

ducting with duct tape

Place DAMPER

inside CEILING opening

ceiling

FAN

DAMPER

4 TO 3 IN

DUCT ADAPTER

Qty:1

Note: If ducting is 3 inch instead of 4 inch, use the included 4 TO 3 IN DUCT

ADAPTER. Use 4 inch pipe whenever possible. 4 inch pipe is quieter and better for

air flow.

ceiling

3 in ducting

Connect DAMPER, 4 TO 3 IN

DUCT ADAPTER, and

ducting with duct tape

Place DAMPER and

4 TO 3 IN DUCT ADAPTER

inside CEILING opening

FAN

DAMPER

12

8.) Bend the holding tabs you selected outward.

9.) Set FAN into place in the opening using holding tabs, now the tabs hold the fan

in position in the ceiling opening.

holding tab

WARNING: Disconnect the AC power before any work is done to any part of

the circuit ReVent is connected to. If you do not understand this warning,

seek the services of a qualified licensed electrician.

WARNING: Copper to copper only. Do not use aluminum wire.

WARNING: Follow all local electrical and safety codes, and NEC (National

Electrical Codes).

CAUTION: If your house wires do not match these colors, determine what

each house wire represents before connecting. You may need to consult a

qualified licensed electrician to determine this safely.

10.) Remove the electrical cover set screw and slide open the electrical enclosure.

Disconnect FAN motor from electrical enclosure.

7.) Select a set of holding tabs, depending on the thickness of your sheetrock. In

the ceiling,

5

/

8

inch sheetrock is the most common.

5

/

8

in (1.6 cm)

holding tab

1

/

2

in (1.3 cm)

holding tab

final

securing

tab

5

/

8

in (1.6 cm)

holding tab

1

/

2

in (1.3 cm)

holding tab

remove

set screw

unplug fan

connectors slide

13

11.) Connect wiring using the provided WIRE NUTS.

line

ground

line

ground

housing

ground

line

neutral

line

neutral

FAN

neutral

light

neutral

line in

light

line in

FAN

Wire connection for fan and light on separate switches:

WIRE NUT

Qty:4

Wire connection for fan and light on one switch:

line

ground

housing

ground

line

neutral

FAN

neutral

light

neutral

line in

FAN

WIRE NUT

Qty:3

light

12.) Once connected, reattach the electrical enclosure.

14

ReVent® fan

fan switch

(purchased separately) light switch

(purchased separately)

120V line AC

black

white

ground

lightfan

black

SWITCHES NOT INCLUDED, USE EXISTING OR MUST BE PURCHASED

SEPARATELY

Always follow all safety instructions included with the switch you purchase. Do not

exceed maximum electrical ratings.

The LED light

can be connected

to a dimmer switch

The FAN wires

cannot be

connected to a

dimmer switch

reattach

set screw

plug in

connectors

slide

15

14.) Align TRIM RING to vent position. Vent position is marked on TRIM RING

with the world “VENT”. Attach TRIM RING to FAN. TRIM RING attaches to FAN

body and presses into place when secure.

13.) Press and bend the final securing tabs flat against ceiling to lock the FAN in

place.

final securing tabs

sheetrock

(ceiling)

apply even

pressure to

each side of

securing tab

ceiling

TRIM RING

final securing tabs

FAN

electrical enclosure

15.) Select desired LED color temperature by sliding the selector switch on the

back of the SHIELD.

daylight (5000K)

bright white (4000K)

warm white (2700K)

SHIELD

16

16.) Attach the SHIELD by squeezing the mounting springs together and inserting

the springs into the spring guides in the FAN.

Installation For New

Construction Framing

NOTE: Even with new construction, you can use the SheetLock® installation

method; however, ReVent® can still be installed using a method home

builders would be more familiar with, as outlined in this section.

WARNING: Disconnect all AC Power Breakers or Fuses before attempting

to cut into your ceiling.

1.) Select a set of holding tabs, depending on the thickness of your sheetrock.

In

the ceiling,

5

/

8

inch sheetrock is the most common.

2.) Bend the holding tabs you selected outward.

5

/

8

in (1.6 cm)

holding tab

1

/

2

in (1.3 cm)

holding tab

final

securing

tab

5

/

8

in (1.6 cm)

holding tab

1

/

2

in (1.3 cm)

holding tab

SHIELD

mounting springs

TRIM RING

ceiling

FAN

spring guide

LED plug

17

3.) Place the sheetrock holding tabs against the bottom of the joist. Attach FAN to

framing joist using ROUNDHEAD WOOD SCREWS.

ROUNDHEAD

WOOD SCREW

Qty:4

framing joist

mount

FAN

framing joist

mount

4.) Attach conduit with wiring to FAN.

conduit

DAMPERFAN

5.) Attach DAMPER to ducting.

Attach DAMPER to

ducting with duct tape

framing joist

ducting

holding tabs flush

to bottom of joist

18

WARNING: Disconnect the AC power before any work is done to any part of

the circuit ReVent is connected to. If you do not understand this warning,

seek the services of a qualified licensed electrician.

WARNING: Copper to copper only. Do not use aluminum wire.

WARNING: Follow all local electrical and safety codes, and NEC (National

Electrical Codes).

CAUTION: If your house wires do not match these colors, determine what

each house wire represents before connecting. You may need to consult a

qualified licensed electrician to determine this safely.

6.) Remove the electrical cover set screw and slide open the electrical enclosure.

Disconnect FAN motor from electrical enclosure.

7.) Connect wiring using the provided WIRE NUTS.

line

ground

line

ground

housing

ground

line

neutral

line

neutral

FAN

neutral

light

neutral

line in

light

line in

FAN

Wire connection for fan and light on separate switches:

WIRE NUT

Qty:4

Wire connection for fan and light on one switch:

line

ground

housing

ground

line

neutral

FAN

neutral

light

neutral

line in

FAN

WIRE NUT

Qty:3

light

remove

set screw

unplug fan

connectors slide

19

8.) Once connected, reattach the electrical enclosure.

ReVent® fan

fan switch

(purchased separately) light switch

(purchased separately)

120V line AC

black

white

ground

lightfan

black

SWITCHES NOT INCLUDED, USE EXISTING OR MUST BE PURCHASED

SEPARATELY

Always follow all safety instructions included with the switch you purchase. Do not

exceed maximum electrical ratings.

The LED light

can be connected

to a dimmer switch

The FAN wires

cannot be

connected to a

dimmer switch

reattach

set screw

plug in

connectors

slide

La page charge ...

ReVent RVL50 Guide d'installation

ReVent RVL50 Guide d'installation

dans d''autres langues