Firman H08051 Le manuel du propriétaire

P/N:336745482 Rev:06

OWNER’S MANUAL

Read all safety precautions and instructions carefully

before operating equipment.

Ensure engine is stopped and level before performing

any maintenance or service.

IMPORTANT:

Record product information to reference when ordering parts or

obtaining warranty coverage.

Serial Number:

DUAL FUEL GENERATOR

MODEL NUMBER

H03652

Rev Level:01

DO NOT RETURN TO

STORE!

CALL US FIRST!

CUSTOMER HOTLINE

1-844-347-6261

FOR QUESTIONS OR SERVICE

INFORMATION

Purchase Date:

Table of Contents

English Customer Service: 1-844-FIRMAN1

. . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety Precautions . . . . . . . . . . . . . . . . . . . . .2

Unpacking the Generator. . . . . . . . . . . . . . . .6

Parts Included. . . . . . . . . . . . . . . . . . . . . . . .7

Removal of Shipping Supports . . . . . . . . . . . . 8

Assembly . . . . . . . . . . . . . .. . . . . . . . . . . . . . . 9

Install the Wheel Kit . . . . . . . . . . . . . . . . . . 9

Install the Support Leg. . . . . . . . . . . . . . . . 9

. . . . . . . . . . . . . 10

Controls and Features. . . . . . . . . . . . . . . . . 11

Generator. . . . . . . . . . . . .. . . . . . . . . . . . . .11

Control Panel. . . . . . . . . . . . . . . . . . . . . . . 12

Specifications. . . . . . . . . . . . . . . . . . . . . . . . 13

Add Engine Oil . . . . . . . . . . . . . . . . . . . . . .14

Low Oil Shutdown . . . . . . . . . . . . . . . . . . .14

Add Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Operation at High Altitude . . . . . . . . . . .17

Grounding. . . . .. . . . . . . . . . . . . . . .. . . . . .18

System.. . . . . . . . . . . . . . . . . . . . . . .. . . . . .18

Operation . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 19

Generator Location . . . . . . . . . . . . . . . . . . 19

Surge Protection . . . . . . . . . . . . .. . . . . . . .19

Starting the Generator (Gasoline). . . . . . 20

Starting the Generator (LPG). . . . . . . . . 20

Connecting Electrical Loads . . . . . . . .. . . 22

Stopping the Engine . . . . . . . . . . . . . . . . . 22

Low Oil Shutdown . . . . . . . . . . . . . . . . . . 23

Do Not Overload Generator . . . . . . . . . . . 24

Introduction

Battery Cable Connection

Connecting to a Building’s Electrical

Maintenance And Storage. . . . . . . . . . . . . . 25

Maintenance Schedule . . . . . . . . . . . . . 25

Engine Maintenance .. . . . . . . . . . . .. . . . 26

Change Engine Oil . . .. . . . . . . . . . . . . . 26

Air Filter Maintenance. . . . . . . . . . . . . .26

Spark Plug Maintenance. . . . . . . . . . . . 27

Cleaning Fuel Strainer . . . . . . . . . . . . 27

. . . 27

Generator Maintenance . . . . . . . . . . . . . . 28

. . . . . . . . . . . . . . . 28

Service and Storage . . . . . . . . . . . . . . . .. 29

Trouble Shooting . . . . . . . . . . . . . . . . . . . . .30

Parts Diagram and Parts List . . . . . . . . . . 31

Generator Parts Diagram . . . . . . . . . . . . 31

Engine Parts Diagram . . . . . . . . . .. . . . . 32

Parts List . . . . . . . . . . . . . . . . . . . . . . . . . 33

Service Information . . . . . . . . . . . . . .. . . . . 35

Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Inspect Muffler and Spark Arrester

Battery Replacement

Indicator light - Battery Power Saving Mode . . 23

Thank you for purchasing a FIRMAN generator.

This manual covers operation and maintenance of the FIRMAN generators. All information in this

publication is based on the latest production information available at the time of approval for printing.

The manufacturer reserves the right to change, alter or other wise improve the generator and this

documentation at any time without prior change.

Page 01

This manual contains safety information to make you aware of the hazards and risks associated

with generator products and how to avoid them. This generator is designed and intended only

for supplying electrical power for operating compatible electrical lighting, appliances, tools and

motor loads, and is not intended for any other purpose. It is important that you read and

understand these instructions thoroughly before attempting to start or operate this equipment.

Save these original instructions for future reference.

Important Safety Information

The manufacturer cannot possibly anticipate every possible circumstance that might involve a

hazard. The warnings in this manual and the tags and decals affixed to the unit are therefore not

all-inclusive. If you use a procedure, work method or operating technique that the manufacturer

does not specifically recommend you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure work method or operating technique that you choose

does not render the generator unsafe.

SAFETY INFORMATION

DANGER WARNING CAUTION

DANGER indicates a

potentially hazardous

situation which, if not

avoided. WILL result in

death or serious injury.

WARNING indicates a

potentially hazardous

situation which, if not

avoided, could result in

death or serious injury.

CAUTION indicates a

potentially hazardous

situation which, if not

avoided, may result in minor

or moderate personal injury,

or property damage.

Toxic Fumes

Fire Hazard

Hot Surface.

Do Not Touch the Surface.

Kickback

Risk of Electric Shock

Explosion Hazard

Rotating Parts Entanglement

Hazard

Operator’s Manual

INTRODUCTION

English Customer Service: 1-844-FIRMAN1

SAFETY PRECAUTIONS

Page 02

WARNING

POISONOUS GAS HAZARD.

•

English Customer Service: 1-844-FIRMAN1

Page 03

CORRECT USAGE

Example location to reduce risk of carbon monoxide poisoning

•ONLY use outside and downwind, far away from windows, doors and vents.

•Direct exhaust away from occupied spaces.

INCORRECT USAGE

Do not operate in any of the following locations:

Near any door, window or vent

Garage

Basement

Crawl Space

Living Area

Attic

Entry Way

Porch

Mudroom

English Customer Service: 1-844-FIRMAN1

Page 04

WHEN OPERATING EQUIPMENT

•

DO NOT tip engine or equipment at angle

which causes fuel or oil to spill.

DO NOT stop engine by moving choke

control to “Start” position.

•

WHEN TRANSPORTING, MOVING

OR REPAIRING EQUIPMENT

Transport/move/repair with fuel tank

EMPTY or with fuel shut OFF.valve

•

•DO NOT tip engine or equipment at angle

which causes fuel or oil to spill.

Disconnect spark plug wire.

•

WHEN STORING FUEL OR EQUIPMENT

WITH FUEL IN TANK

•

WARNING

•

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

WARNING

•

•NEVER start or stop engine with electrical

devices plugged in and turned on.

WARNING

Gasoline, gasoline vapors and liquid petroleum

gas(LPG) are extremely flammable and explosive

which could cause burns, fire, or explosion resulting

in death or serious injury and/or property damage.

WHEN ADDING OR DRAINING GASOLINE

Turn generator engine OFF and let it cool at

least 2 minutes before removing fuel cap.

Loosen cap slowly to relieve pressure in tank.

Fill or drain fuel tank outdoors.

•

•DO NOT overfill tank. Allow space for fuel

expansion.

If fuel spills, wait until it evaporates before

starting engine.

•

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap, and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke.

•

WHEN STARTING EQUIPMENT

Ensure spark plug, muffler, fuel cap, and air

cleaner are in place.

•

DO NOT crank engine with spark plug

removed.

•Use approved transfer equipment, suitable

for the intended use, to prevent backfeed by

isolating generator from electric utility

workers.

English Customer Service: 1-844-FIRMAN1

Make certain that a LPG cylinder is not attached

to generator and is securely stowed away.

•

Do not store gasoline or LPG cylinder near

furnaces, water heaters, or any other appliances

that produce heat or have automatic ignitions.

•

Page 05

WARNING

Unintentional sparking

could cause fire or

electric shock resulting

in death or serious

injury.

WHEN ADJUSTING OR MAKING REPAIRS TO

YOUR GENERATOR

Disconnect the spark plug wire from the

spark plug and place the wire where it cannot

contact spark plug.

•

WHEN TESTING FOR ENGINE SPARK

Use approved spark plug tester.

•DO NOT check for spark with spark plug

removed.

•

WARNING

NEVER operate generator without protective

housing or covers.

DO NOT wear loose clothing, jewelry or

anything that could be caught in the starter

or other rotating parts.

Tie up long hair and remove jewelry.

•

DO NOT exceed the generator’s wattage

amperage capacity.

Start generator and let engine stabilize

before connecting electrical loads.

NOTE:

•

CAUTION

Exceeding generators wattage/amperage capacity

could damage generator and/or electrical devices

connected to it.

Connect electrical loads in OFF position,

then turn ON for operation.

Turn electrical loads OFF and disconnect

from generator before stopping generator.

•

DO NOT use generator with electrical cords

which are worn, frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or

wet weather.

DO NOT handle generator or electrical

cords while standing in water, while

barefoot, or while hands or feet are wet.

DO NOT allow unqualified persons or

children to operate or service generator.

•

WARNING

Exhaust heat/gases could ignite combustibles,

structures or damage fuel tank causing a fire,

resulting in death or serious injury and/or

property damage.

Contact with muffler area could cause burns

resulting in serious injury.

DO NOT touch hot parts and AVOID hot

exhaust gases.

Allow equipment to cool before touching.

It is a violation of California Public Resource

Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered,

or grass-covered land unless the exhaust

system is equipped with a spark arrester, as

defined in Section 4442, maintained in

effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer,

retailer, or dealer to obtain a spark arrester

designed for the exhaust system installed on

this engine.

Replacement parts must be the same and

installed in the same position as the original

parts.

•

When using generator for backup power,

notify utility company.

Use a ground fault circuit interrupter (GFCI)

in any damp or highly conductive area,

such as metal decking or steel work.

DO NOT touch bare wires or receptacles.

•

English Customer Service: 1-844-FIRMAN1

Page 06

•

Use generator only for intended uses.

If you have questions about intended use,

ask dealer or contact local service center.

Operate generator only on level surfaces.

DO NOT expose generator to excessive

moisture, dust, dirt, or corrosive vapors.

DO NOT insert any objects through cooling

slots.

If connected devices overheat, turn them off

and disconnect them from generator.

Shut off generator if:

-Electrical output is lost.

-Equipment sparks, smokes, or emits flames.

-Unit vibrates excessively.

•

WARNING

Medical and Life Support Uses.

In case of emergency, call 911 immediately.

NEVER use this product to power life support

devices or life support appliances.

NEVER use this product to power medical

devices or medical appliances.

Inform your electricity provider immediately

if you or anyone in your household depends

on electrical equipment to live.

Inform your electrical provider immediately

if a loss of power would cause you or anyone

in your household to experience a medical

emergency.

•

NOTE:

Improper treatment of generator could damage

it and shorten its life.

English Customer Service: 1-844-FIRMAN1

Fuel Safety

DANGER

GASOLINE AND GASOLINE VAPORS ARE HIGHLY

FLAMMABLE AND EXPLOSIVE.

Fire or explosion can cause severe burns or death.

Unintentional startup can result in entanglement,

traumatic amputation or laceration.

Gasoline expands or contracts with ambient

temperatures. Never fill the gasoline tank to

full capacity, as gasoline needs room to expand

if temperatures rise.

Gasoline can cause a fire or explosion if ignited.

Gasoline is a liquid fuel but it’s vapors can ignite.

•

•Gasoline is a skin irritant and needs to be cleaned

up immediately if spilled on skin or clothes.

•Gasoline has a distinctive odor, this will help

detect potential leaks quickly.

•In any gasoline fire, flames should not be

extinguished unless by doing so the fuel supply

valve can be turned OFF. This is because if a fire is

extinguished and a supply of fuel is not turned OFF,

then an explosion hazard could be created.

•

Liquid Petroleum Gas (LPG/Propane):

This generator is dual fuel and capable of running

with both gasoline and Liquid Petroleum Gas

(LPG/Propane).

•

If you smell gas: close off the gas supply. Make

sure there is no leak before using the generator.

•

Gasoline:

Liquid Petroleum Gas (LPG) is highly flammable

and explosive. Fire or explosion can cause severe

burns or death.

Do not use or store LPG cylinder in a building,

garage or enclosed area.

Do not check for leaks with a lighted match or

flame.

The LPG cylinder valve should be fully closed

when the generator is not in use or is running

with gasoline.

DANGER

WARNING

Device used for handling LPG must be installed

and used in strict conformance with NFPA 58

(Liquefied Petroleum Gas Code) and NFPA 54

(National Fuel Gas) and all other codes, regulations

and manufacturer recommendations.

Never use a gas container, LPG connector

hose, LPG cylinder or any other fuel item that

is damaged or appears damaged.

The LPG cylinder valve should be fully closed

when the generator is not in use or is running

with gasoline.

•

•The regulator/hose assembly and cylinder

valve must be inspected before each use for

leaks or sign of damages.

Page 07

English Customer Service: 1-844-FIRMAN1

UNPACKING THE GENERATOR

•

Parts Included

Your gasoline powered generator ships with

the following parts:

1. Axle pin . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

2. 8.0" in. Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . 2

3. Flat Washer. . . . . . . . . . . . . . . .. . . . . . . . . . . . . .2

4. Cotter pin. . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . .2

5. Engine Oil(Bottle) . . . .. . . . . . . . . . . . . . . . . . . .1

6. Oil Funnel . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . 1

7. Wrench for Spark plug . . . . . . . . . . . . . . . . . . . .1

8. Double Open wrench (10mm & 12mm). . . . 2

9. Support Leg with Vibration Mounts . . . . . . 1

10. Flange Bolt (M8x16 for Support Leg) . . . . . 2

11. Flange Lock Nut (M8) . . . . . . . . . . . . . . . . . . . 4

12. Handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . 1

13.

14. Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

15. Quick Reference Guide . . . . . . . . . . . . . . . . . 1

LPG Hose With Regulator 5 ft. (1.5 m) . . . 1

16. Hose Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

If you smell gas: close off the gas supply. Spray

a soapy water solution to check all connections

for leaks before attempting to use generator.

Contact a qualified technician to inspect and

repair the LPG system if a leak found before

using the generator.

•

CAUTION

LPG under pressure is highly flammable and

can cause a fire or explosion if ignited.

LPG is heavier than air and can accumulate in

confined spaces and low places in the event

of a leak.

LPG has a distinctive odor to help detect

potential leaks.

Do not allow children to tamper or play with

the LPG cylinder.

In the event of an LPG fire, flames should not

be extinguished unless by doing so the fuel

supply valve can be turned off. If the fire is

extinguished and a supply of fuel is not turned

off, an explosion hazard greater than the fire

hazard could be created.

Keep a fire extinguisher near the generator all

the time.

Always keep the LPG cylinder in an upright

position.

Do not subject LPG cylinder to excessive heat.

Contact with liquid contents of the cylinder

will cause freeze burns to the skin.

An LPG cylinder not connected for use shall

not be stored in the vicinity of the generator.

When transporting and storing, turn off the

cylinder valve and fuel selector switch, and

disconnect the cylinder.

•

16

Page 08

REMOVAL OF SHIPPING SUPPORTS

Before you can run your new generator, follow

these simple instructions:

CAUTION

Failure to remove these items can result

in damage to your generator, possible

Personal injury and void your warranty.

Refer to the following instructions and pictures

to remove the attached engine support brackets

(red) under the engine.

3. You may discard these brackets, as it is no longer

required for normal operation of your generator.

Your generator is now ready for use. Refer to

your owner's manual for proper oil fill and

startup instructions.

Red Engine Support Brackets

Remove These Nuts &

Bolts as Indicated.

Supplied Wrenches

English Customer Service: 1-844-FIRMAN1

Page 09

Install the Wheel Kit

The wheel kit is not intended for over-the-road

use.

Install the Support Leg

ASSEMBLY

A

B

C

The generator requires some assembly prior to

usage. If problem arise when assembling the

generator, call 1-844-347-6261.

1. Before adding wheels, tip the generator on

its side.

2. Slide the axle pin A through the wheel B.

3. Slide the axle pin A through the mount point

on the frame and washer D .

4. Secure the wheel and axle pin with the cotter

pin C .

5. Repeat steps 2-4 to attach another wheel.

1. Attach the support leg G to the generator

frame with flange bolts E (M8x16) and flange

lock nuts F(M8).

2. Tip the generator slowly so that it rests

on the wheels and support leg.

3.Tighten bolt E and nut F with provide

wrenches

CAUTION

D

F

G

E

English Customer Service: 1-844-FIRMAN1

Page 10

English Customer Service: 1-844-FIRMAN1

Battery Cable Connection

NOTE:

The generator comes equiped with the positive red cable(red cable) already attached.

1. Verify the positive (+) red cable is securely tightened to the positive (+) terminal.

2. Connect the negative(-) black cable to negative(-) terminal on the battery.

Page 11

CONTROLS AND FEATURES

Generator

1- Fuel Gauge

2- 5.0 Gallon Capacity Fuel Tank

3- Fuel Cap

4- Choke Lever(behind air filter box)

5- Air Filter

6- 208cc FIRMAN OHV Engine

7- Recoil Starter

8- 8.0" Flat Free Wheel

9-

10-

11-

12-

13-

Oil Filler Cap

LPG Hose Connector(Inlet)

Outlet Cover

Control Panel

Handle

14- Hose Holder

15- LPG Hose with Regulator

English Customer Service: 1-844-FIRMAN1

*We are always working to improve our products. Therefore, the enclosed product may differ

slightly from the image on this page.

2

①

②

③

⑤

⑥

⑦⑧⑨

⑩

⑪

⑫

④⑬

⑮

⑭

2

3

4

5

6

7

8

9

10

2

3

4

Page 12

NOTE: Total power drawn from all receptacles must not exceed the name plate rating.

1

Control Panel

English Customer Service: 1-844-FIRMAN1

13-1 Data-Minder(Multi-Meter) – Push the

SELECT button to show the Voltage, Hertz

and running hours.

5120V, 20A Duplex – (NEMA 5-20R) 20 Amp

of current may be drawn from this 120 Volt

receptacle.

6120V, 30A RV (NEMA TT-30R)

Maximum full load 30 Amp current may be

drawn from this 120 Volt receptacle.

7Ground Terminal – Consult an electrician

for local grounding regulations.

8120V, 30A Twist-Lock (NEMA L5-30R)

Maximum full load 30 Amp current may be

drawn from this 120 Volt receptacle.

9Outlet Cover - Protect the receptacles from

dust and debris.

10 LPG Hose Connector(Inlet) – Used to connect

LPG hose to generator.

Indicator Light

When the fuel selector switch is turned to the

“GAS” or “LPG” position, the indicator light will

become RED up to 4 minutes(before goes off).

Starting the engine successfully during these

4 minutes will turn the indicator light GREEN.

MUST HAVE SOLID RED INDICATOR LIGHT

TO BE ABLE TO START THE GENERATOR. THE

GENERATOR CANNOT BE STARTED DURING

BATTERY POWER SAVING MODE UNLESS

THE FUEL SELECTOR SWITCH IS TURNED TO

THE “OFF” POSITION AND THEN TURNED

BACK TO THE “GAS” OR “LPG” POSITION.

See Indicator light-Battery power Saving

Mode section for more information.

Fuel Selector Switch – Use to select and turn

on gasoline or LPG fuel source. Fuel (gasoline)

valve is closed when the switch is on “OFF” or

“LPG” positions. Engine switch is on when the

switch is on “GAS” or “LPG” positions.

Page 13

SPECIFICATIONS

Model

Rated AC Voltage

Phase

Power Factor

Voltage Regulator

Alternator Type

Running Watts

Starting Watts

Engine

Engine Type

Displacement

Low Oil Shutdown

Ignition System

Starting System

Fuel

Capacity Fuel Tank

Lubricating Oil Capacity

Carburetor Type

Air Cleaner

P.T.O. Shaft Rotation

120V

H03652

3650(GAS )/3300(LPG)OLINE

AVR

Single

1

Single Cylinder, 4-Stroke OHV Air Cooled

208cc

Breakless Ignition Type, Flywheel Magneto

Unleaded Automotive Gasoline/LPG

5.0 Gallon

20.3 oz(0.6L)

Counter Clockwise (Facing P.T.O.)

Float

Brushed

Polyurethane Type

Yes

4550(GASOLINE)/4100(LPG)

FIRMAN

Rated Fequency 60Hz

Oil Type

See “Add Engine Oil” Section

AN IMPORTANT MESSAGE ABOUT TEMPERATURE:

When operated above 77°F(25°C) there may be a decrease in power.

Maximum wattage and current are subject to and limited by such factors as fuel BTU content

ambient temperature, altitude, engine condition and etc. Maximum power decreases about

3.5% for each 1,000 feet above sea level; and will also decrease about 1% for each 10°F(6°C)

above 60°F(16°C) ambient temperature.

•

Recoil

English Customer Service: 1-844-FIRMAN1

Grounding System Neutral Bonded to Frame

Total Harmonic Distortion(THD) Standard

ADD ENGINE OIL

Page 14

1.Place generator on a flat, level surface.

2.Clean area around oil fill and remove yellow

oil fill cap/dipstick.

3.Wipe dipstick clean.

NOTE:

The engine is equipped with a low oil shut-off and

will stop when the oil level in the crankcase falls

below the threshold level.

NOTE:

We consider the first 5 hours of run time to be

the break-in period for the unit. During the break

in period stay at or below 50% of the running

watt rating and vary the load occasionally to allow

stator windings to heat and cool. Adjusting the

load will also cause engine speed to vary and help

seat piston rings.

CAUTION

The unit is equipped with a low oil shutdown.If

the oil level becomes lower than required,the

sensor will activate a warning device or stop the

engine.

If generator shuts off and the oil level is within

specifications, check to see if generator is sitting

at an angle that forces oil to shift. Place on an

even surface to correct this. If engine fails to

start, the oil level may not be sufficient to

deactivate low oil level switch. Make sure the

sump is completely full of oil.

(H)

DRAIN PLUG

(L)

5.Replace oil fill cap/dipstick and fully tighten.

6.Oil level should be checked prior to each use

or at least every 8 hours of operation. Keep oil

level maintained.

4.Using oil funnel, slowly pour contents of

provided oil bottle into oil fill opening to the

"H" mark on dipstick. Be careful do not

overfill. Overfilling with oil could cause the

engine to not start or hard starting.

Low Oil Shutdown

Degrees Celsiusº(Outside)

Full Synthetic 5W-30

Degrees Fahrenheitº(Outside)

5W-30 10W-40

10W-30

CAUTION

H

L

English Customer Service: 1-844-FIRMAN1

ADD FUEL

Page 15

Fuel must meet these requirements:

•Clean, fresh, unleaded gasoline.

Use regular UNLEADED gasoline with the

generator engine with a minimum 87 octane

/ 87 AKI (91 RON).

For high altitude use, see "Operation at High

Altitude".

Do not use gasoline with more than 10%

alcohol such as E85 or ethanol.

•

Failure to follow Operator's Manual for fuel

recommendations voids warranty.

Avoid generator damage.

DO NOT use unapproved gasoline such as E85.

DO NOT mix oil in gasoline.

DO NOT modify engine to run on alternate fuels.

•

WARNING

Fuel and its vapors are extremely flammable

and explosive which could cause burns, fire or

explosion resulting in death, serious injury

and/or property damage.

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel

expansion. If the tank is overfilled, fuel

can overflow onto a hot engine and cause fire

or explosion. Wipe up any spilled fuel

immediately.

If fuel spills, wait until it evaporates before

starting engine.

Keep fuel away from sparks, open flames,

pilot lights, heat, and other ignition sources.

Check fuel lines, tank, cap and fittings

frequently for cracks or leaks. Replace if

necessary.

DO NOT light a cigarette or smoke when

filling the fuel tank.

•

1.Clean area around fuel fill cap, remove cap.

2.Slowly add unleaded fuel to fuel tank. Be

careful not to fill above the red fuel level

indicator . This allows adequate space for

fuel expansion.

3.Install fuel cap and let any spilled fuel

evaporate before starting engine or wipe up

any spilled gasoline.

English Customer Service: 1-844-FIRMAN1

1.Gasoline

CAUTION

Slowly add unleaded gasoline to fuel tank.

Do not overfill tank.

Do not fill above the red line indicator.

This will allow expansion in hot weather

and prevent overflow.

•

Red Line Indicator

2-Connecting Liquid Petroleum Gas

(LPG/Propane) Cylinder

•

Liquid Petroleum Gas (LPG) is highly flammable

and explosive. Fire or explosion can cause severe

burns or death.

Do not use or store LPG cylinder in a building,

garage or enclosed area.

DANGER

•Do not place the LPG cylinder in the path of

muffler outlet.

IMPORTANT: It is important to prevent gum

deposits from forming in fuel system parts such

as the carburetor, fuel hose or tank during storage.

Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to

separation and formation of acids during storage.

Acidic gas can damage the fuel system of an engine

while in storage. To avoid engine problems, the

fuel system should be emptied before storage of

30 days or longer. See the " Long Term Storage"

section. Never use engine or carburetor cleaner

products in the fuel tank as permanent damage

may occur.

Page 16

English Customer Service: 1-844-FIRMAN1

•Never use a gas container, LPG connector

hose, LPG cylinder or any other fuel item that

is damaged or appears damaged.

The LPG cylinder valve should be fully closed

when the generator is not in use or is running

with gasoline.

•

•The regulator/hose assembly and cylinder

valve must be inspected before each use for

leaks or sign of damages.

Use only 20 or 30 lb capacity cylinders with

Type 1, right hand Acme threads with this

generator. Verify the re-qualification date

on the tank has not expired. Do not use rusted

or damaged cylinders.

All new cylinders must be purged of air and

moisture prior to filling. Used cylinders that

have not been plugged or kept closed must

also be purged. The purging process should

be done by your propane gas supplier.

Do not connect or disconnect the LPG cylinder

in enclosed area.

Do not install or replace the LPG cylinder near

open flames, pilot lights, or sparking electrical

equipment such as power tools, welders and

grinders.

Attach the LPG regulator/hose assembly

(included) to the LPG hose connector (inlet)

on the control panel of the generator. Tighten

the nut with 19 mm or adjustable wrench.

Remove the safety plug or cap from the

cylinder valve.

Attach the other end of the LPG regulator/hose

assembly to the cylinder valve. Tighten the nut

by hand clockwise to a positive stop. Do not

use a wrench to tighten. Use of wrench may

damage quick closing coupling nut and result

in a hazardous condition.

Do not use tape or any type sealant to seal the

LPG hose connections.

Always position the cylinder so the connection

between the valve and the regulator won’t cause

bends or kinks in the hose.

Spray a soapy water solution (one part liquid

detergent and one part water) to check all

connections for leaks before attempting to

use generator. Slowly open the cylinder valve.

A leak exists if bubbles appear or grow larger

in size or number. This must be corrected before

using the generator. Contact your local

Authorized Service Facility for assistance. Do

not attempt to make repairs yourself.

Do not check for leaks with a lighted match or flame.

Do not light or smoke cigarettes.

Check the fuel system periodically for leaks

or signs of damages.

LPG under pressure is highly flammable and

can cause a fire or explosion if ignited.

CAUTION

•

LPG is heavier than air and can accumulate in confined

spaces and low places in the event of a leak.

LPG has a distinctive odor to help detect

potential leaks.

•

Do not allow children to tamper or play with

the LPG cylinder.

•

If you smell gas: close off the gas supply. Spray

a soapy water solution to check all connections

for leaks before attempting to use generator.

Contact a qualified technician to inspect and

repair the LPG system if a leak found before

using the generator.

•

You must use the supplied regulator/hose

assembly for safe operation.

•WARNING

Device used for handling LPG must be installed

and used in strict conformance with NFPA 58

(Liquefied Petroleum Gas Code) and NFPA 54

(National Fuel Gas) and all other codes, regulations

and manufacturer recommendations.

If you smell gas: close off the gas supply. Make

sure there is no leak before using the generator.

•

Do not check for leaks with a lighted match or

flame.

The LPG cylinder valve should be fully closed

when the generator is not in use or is running

with gasoline.

Page 17

English Customer Service: 1-844-FIRMAN1

Operation at High Altitude

At altitudes over 5,000 feet(1524 meters), a

minimum 85 octane / 85 AKI (89 RON) gasoline

is acceptable.

The density of air at high altitude is lower

than at sea level. Engine power is reduced

as the air mass and air-fuel ratio decrease.

Engine power and generator output will be

reduced approximately 3.5% for every 1000 feet

of elevation above sea level. This is a

natural trend and cannot be changed by

adjusting the engine. At high altitudes

increased exhaust emissions can also result

due to the increased enrichment of the air

fuel ratio.

Other high altitude issues can include hard

starting, increased fuel consumption and

spa rk p lug f ou lin g. T o al lev iat e hi g h

al titude issues other than the na tural

power loss, FIRMAN can provide a high

altitude carburetor main jet. The alternative

The part number and recommended minimum

altitude for the application of the high

altitude carburetor main jet is listed in the

table below.

main jet and installation instructions can be

obtained by contacting Customer Support.

Installation instructions are also available in the

Technical Bulletin area of the FIRMAN internet site.

Altitude main jet 1

Altitude main jet 2

208cc

335717004

335717005

Altitude

3000-6000Feet

6000-8000Feet

OPEN

WARNING

3-Permanent Connection to a large

Propane supply tank:

In the instance that you would need to connect

your generator to a large propane Supply tank,

larger than 20 or 30 lb DOT cylinder, it is

recommended to contact your Gas Equipment

Company. Various equipment for use with LPG,

is required for proper conformance to all NFPA

regulations. Your Gas Equipment Company can

help you select and install the proper regulator,

fittings and connections to meet all the Codes

and manufacturer regulations. Each installation

may be different and will required proper equipment.

Contact your Gas Equipment Company to assure

that you are meeting all NFPA 58 (Liquefied

Petroleum Gas Code) and NFPA 54 (National Fuel

Gas) Codes.

When transporting and storing, turn off the

cylinder valve and fuel selector switch, and

disconnect the cylinder.

Contact with liquid contents of the cylinder

will cause freeze burns to the skin.

•

An LPG cylinder not connected for use shall

not be stored in the vicinity of the generator.

•

•Always keep the LPG cylinder in an upright

position.

Do not subject LPG cylinder to excessive heat.

•

In the event of an LPG fire, flames should not

be extinguished unless by doing so the fuel

supply valve can be turned off. If the fire is

extinguished and a supply of fuel is not turned

off, an explosion hazard greater than the fire

•

hazard could be created.

•Keep a fire extinguisher near the generator

all the time.

Page 18

Grounding

The National Electric Code requires your generator

must be properly connected to an appropriate

ground to help prevent electric shock.

Failure to properly ground the

generator can result in electric

shock.

WARNING

THERE IS A PERMANENT CONDUCTOR BETWEEN

THE GENERATOR (STATOR WINDING) AND THE

FRAME.

Use approved transfer equipment to prevent

backfeed by isolating generator from electric

utility workers.

When using generator for backup power, notify

utility company.

Use a ground fault circuit interrupter (GFCI) in

any damp or highly conductive area, such as

metal decking or steel work.

DO NOT touch bare wires or receptacles.

DO NOT use generator with electrical cords

which are worn,frayed, bare or otherwise

damaged.

DO NOT operate generator in the rain or wet

weather.

DO NOT handle generator or electrical cords

while standing in water, while barefoot, or

while hands or feet are wet.

DO NOT allow unqualified persons or children

to operate or service generator.

Connecting to a Building's Electrical System

WARNING

Generator voltage could cause

electrical shock or burn resulting

in death or serious injury.

•

English Customer Service: 1-844-FIRMAN1

La page charge ...

Firman H08051 Le manuel du propriétaire

Ce manuel convient également à

Firman H08051 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents