DeWalt DCD780B Le manuel du propriétaire

Marque: DeWalt

Modèle: DCD780B

Catégorie: Perceuses mixtes sans fil

Taper: Le manuel du propriétaire

Ce manuel convient également à

DCD780C2

DCD780 20V Max* Cordless Compact 1/2" (13 mm) Drill/Driver

DCD785 20V Max* Cordless Compact 1/2" (13 mm) Drill/Driver/Hammerdrill

DCD780 Perceuse/visseuse compact sans fil de 13 mm (1/2") de 20 V max*

DCD785 Marteau perforateur/perceuse/visseuse compact sans fil de 13 mm (1/2")

de 20 V max*

Taladro/destornillado inalámbrico compacto de 13 mm (1/2") de 20 V Máx* DCD780

Taladro/destornillado/percutor inalámbrico compacto de 13 mm (1/2") de 20 V Máx* DCD785

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury.

NOTICE: Indicates a practice not related to personal

injury which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND

INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust

or fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators.

There is an increased risk of electric shock if your body is

earthed or grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged

or entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a cord

suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is

unavoidable, use a ground fault circuit interrupter

(GFCI) protected supply. Use of a GFCI reduces the risk of

electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

English

power tool while you are tired or under the influence

of drugs, alcohol or medication. A moment of inattention

while operating power tools may result in serious personal

injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying the

tool. Carrying power tools with your finger on the switch

or energizing power tools that have the switch on invites

accidents.

d) Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to a

rotating part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool

or these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of

battery pack may create a risk of fire when used with another

battery pack.

b) Use power tools only with specifically designated

battery packs. Use of any other battery packs may create a

risk of injury and fire.

c) When battery pack is not in use, keep it away from

other metal objects, like paper clips, coins, keys, nails,

screws, or other small metal objects, that can make a

connection from one terminal to another. Shorting the

battery terminals together may cause burns or a fire.

English

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally

occurs, flush with water. If liquid contacts eyes,

additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Drill/Driver/Hammerdrill Safety

Warnings

• Wear ear protectors when impact drilling. Exposure to

noise can cause hearing loss.

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory

may contact hidden wiring. Cutting accessory contacting a

“live” wire may make exposed metal parts of the power tool “live”

and could give the operator an electric shock.

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by

hand or against your body is unstable and may lead to loss of

control.

• Wear safety goggles or other eye protection. Hammering

and drilling operations cause chips to fly. Flying particles can

cause permanent eye damage.

• Accessories and tool may get hot during operation.

Wear gloves when handling them if performing heat producing

applications such as hammerdrilling and drilling metals.

• Do not operate this tool for long periods of time. Vibration

caused by hammer action may be harmful to your hands and

arms. Use gloves to provide extra cushion and limit exposure by

taking frequent rest periods.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be caught in

moving parts.

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or dust mask

if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY

EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains

chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed

to filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction

activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption of

harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

English

WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19) during

use. Under some conditions and duration of use, noise from this

product may contribute to hearing loss.

CAUTION: When not in use, place tool on its side on a

stable surface where it will not cause a tripping or falling

hazard. Some tools with large battery packs will stand upright on

the battery pack but may be easily knocked over.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ................... volts A ......................amperes

Hz ................. hertz W .....................watts

min ............... minutes or AC ..........alternating

or DC ... direct current current

................. Class I Construction or AC/DC ...alternating

.....................

(grounded) ........................or direct

................. Class II Construction current

(double insulated) no ....................no load

…/min .......... per minute speed

BPM ............. beats per minute

n ......................rated

IPM ...............impacts per minute ........................speed

RPM ............. revolutions per .....................earthing

minute terminal

sfpm .............surface feet ..................... safety alert

..................... per minute symbol

SPM ............. strokes per minute

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below and then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery pack

from the charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (40°C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in

the ON position.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If the battery pack case is cracked or damaged,

do not insert into the charger. Do not crush, drop or damage

the battery pack. Do not use a battery pack or charger that has

received a sharp blow, been dropped, run over or damaged in

any way (e.g., pierced with a nail, hit with a hammer, stepped on).

Damaged battery packs should be returned to the service center

for recycling.

WARNING: Fire hazard. Do not store or carry the battery

pack so that metal objects can contact exposed battery

terminals. For example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc., with loose

nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in

English

contact with conductive materials such as keys, coins,

hand tools and the like. The US Department of Transportation

Hazardous Material Regulations (HMR) actually prohibit transporting

batteries in commerce or on airplanes (e.g., packed in suitcases

and carry-on luggage) UNLESS they are properly protected from

short circuits. So when transporting individual battery packs, make

sure that the battery terminals are protected and well insulated

from materials that could contact them and cause a short circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION

(Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention is

needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corp oration) Seal on

the nickel cadmium, nickel metal hydride or lithium

ion batteries (or battery packs) indicate that the

costs to recycle these batteries (or battery packs) at

the end of their useful life have already been paid by

DEWALT. In some areas, it is illegal to place spent

nickel cadmium, nickel metal hydride or lithium ion batteries in the

trash or municipal solid waste stream and the RBRC program

provides an environmentally conscious alternative.

RBRC™, in cooperation with DEWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or

lithium ion batteries. Help protect our environment and conserve

natural resources by returning the spent nickel cadmium, nickel

metal hydride or lithium ion batteries to an authorized DEWALT

service center or to your local retailer for recycling. You may also

contact your local recycling center for information on where to

drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary

markings on the charger, battery pack and product using the

battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside

the charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge

only DEWALT rechargeable battery packs. Other types of batteries

may overheat and burst resulting in personal injury and property

damage.

NOTICE: Under certain conditions, with the charger plugged into

the power supply, the charger can be shorted by foreign material.

Foreign materials of a conductive nature, such as, but not limited to,

grinding dust, metal chips, steel wool, aluminum foil or any buildup

of metallic particles should be kept away from the charger cavities.

Always unplug the charger from the power supply when there is no

battery pack in the cavity. Unplug the charger before attempting to

clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to work together.

English

• These chargers are not intended for any uses other than

charging DEWALT rechargeable batteries. Any other uses

may result in risk of fire, electric shock or electrocution.

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting

the charger. This will reduce the risk of damage to the electric

plug and cord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected to

damage or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor

use. Use of a cord suitable for outdoor use reduces the risk of

electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is,

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The lower the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere

Rating

Volts Total Length of Cord

in Feet (meters)

120 V 25

(7.6) 50

(15.2) 100

(30.5) 150

(45.7)

240 V 50

(15.2) 100

(30.5) 200

(61.0) 300

(91.4)

Than

Not

Than AWG

0 6 18 16 16 14

610 1816 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the

charger in a position away from any heat source. The charger

is ventilated through slots in the top and the bottom of the

housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any way.

Take it to an authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or

fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it

English

on any other voltage. This does not apply to the vehicular

charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety

instructions before using your charger. Consult the chart at the end

of this manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate FIG. 1 K

DCB101

outlet before inserting the battery

pack.

2. Insert the battery pack (K) into the

charger, as shown in Figure 1,

making sure the pack is fully seated

in charger. The red (charging) light will

blink continuously, indicating that the

charging process has started.

3. The completion of charge will be

indicated by the red light remaining

ON continuously. The pack is fully

charged and may be used at this

time or left in the charger.

Indicator Light Operation

DCB101

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

PROBLEM PACK OR CHARGER

PROBLEM POWERLINE

DCB107, DCB112

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

This charger is designed to detect certain problems that can arise.

Problems are indicated by the red light flashing at a fast rate. If this

occurs, re-insert the battery pack into the charger. If the problem

persists, try a different battery pack to determine if the charger is

working properly. If the new pack charges correctly, then the original

pack is defective and should be returned to a service center or other

collection site for recycling. If the new battery pack elicits the same

trouble indication as the original, have the charger and the battery

pack tested at an authorized service center.

HOT/COLD DELAY

DCB101

This charger has a hot/cold delay feature: when the charger detects

a battery that is hot, it automatically starts a delay, suspending

charging until the battery has cooled. After the battery has cooled,

the charger automatically switches to the pack charging mode. This

feature ensures maximum battery life. The red light flashes long,

then short while in the hot/cold delay mode.

DCB107, DCB112

The DCB107 and DCB112 chargers have a hot/cold delay feature.

When the charger detects a battery that is hot, it automatically

delays charging until the battery has cooled. When the charger

detects a battery that is cold, it automatically delays charging until

the battery has warmed.

The red light will continue to blink, but a yellow indicator light will

be illuminated during this operation. Once the battery has cooled,

English

the yellow light will turn off and the charger will resume the charging

procedure.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the

charge indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

PROBLEM POWER LINE (DCB101)

Some chargers have a Problem Power Line indicator. When the

charger is used with some portable power sources such as

generators or sources that convert DC to AC, the charger may

temporarily suspend operation, flashing the red light with two fast

blinks followed by a pause. This indicates the power source is out

of limits.

Wall Mounting

DCB107, DCB112

These chargers are designed to be wall mountable or to sit upright

on a table or work surface.

If wall mounting, locate the charger within reach of an electrical

outlet. Mount the charger securely using drywall screws at least

1" (25.4 mm) long, screwed into wood to an optimal depth leaving

approximately 7/32" (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the

battery pack is charged when the air temperature is between

65°F and 75°F (18° – 24°C). DO NOT charge the battery pack

in an air temperature below +40°F (+4.5°C), or above +104°F

(+40 °C). This is important and will prevent serious damage to

the battery pack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery pack

after use, avoid placing the charger or battery pack in a warm

environment such as in a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights;

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24°C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously.

DO NOT CONTINUE to use under these conditions. Follow

the charging procedure. You may also charge a partially used

pack whenever you desire with no adverse effect on the battery

pack.

6. Foreign materials of a conductive nature such as, but not

limited to, grinding dust, metal chips, steel wool, aluminum foil,

or any buildup of metallic particles should be kept away from

charger cavities. Always unplug the charger from the power

supply when there is no battery pack in the cavity. Unplug the

charger before attempting to clean.

7. Do not freeze or immerse the charger in water or any other

liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

the charger. Electric shock may result.

English

WARNING: Burn hazard. Do not submerge the battery pack

in any liquid or allow any liquid to enter the battery pack. Never

attempt to open the battery pack for any reason. If the plastic

housing of the battery pack breaks or cracks, return to a service

center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from

direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted

of charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

COMPONENTS (Fig. 2)

WARNING: Never modify the power tool or any part of it.

Damage or personal injury could result.

A. Trigger switch H. Mounting screw

B. Forward/reverse control button I. Bit clip

C. Torque adjustment collar (Optional accessory)

D. Gear shifter J. Battery release button

E. Worklight K. Battery pack

F. Keyless chuck

G. Belt hook (Optional accessory)

FIG. 2 D

Variable Speed Trigger Switch (Fig. 2)

To turn the tool on, squeeze the trigger switch (A). To turn the tool

off, release the trigger switch. Your tool is equipped with a brake.

The chuck will stop as soon as the trigger switch is fully released.

NOTE: Continuous use in variable speed range is not recommended.

It may damage the switch and should be avoided.

Forward/Reverse Control Button (Fig. 2)

A forward/reverse control button (B) determines the direction of

the tool and also serves as a lock-off button.

To select forward rotation, release the trigger switch and depress

the forward/reverse control button on the right side of the tool.

English

To select reverse, depress the forward/reverse control button on

the left side of the tool.

The center position of the control button locks the tool in the off

position. When changing the position of the control button, be sure

the trigger is released.

NOTE: The first time the tool is run after changing the direction of

rotation, you may hear a click on start up. This is normal and does

not indicate a problem.

Torque Adjustment Collar (Fig. 2)

Your tool has an adjustable torque screwdriver mechanism for

driving and removing a wide array of fastener shapes and sizes and

in some models, a hammer mechanism for drilling into masonry.

Circling the collar (C) are numbers, a drill bit symbol, and in some

models, a hammer symbol. These numbers are used to set the

clutch to deliver a torque range. The higher the number on the

collar, the higher the torque and the larger the fastener which can

be driven. To select any of the numbers, rotate until the desired

number aligns with the arrow.

Dual Range Gearing (Fig. 2)

The dual range feature of your drill/driver allows you to shift gears

for greater versatility.

1. To select speed 1 (high torque setting), turn the tool off and

permit it to stop. Slide the gear shifter (D) forward (towards the

chuck).

2. To select speed 2 (low torque setting), turn the tool off and

permit it to stop. Slide the gear shifter back (away from the

chuck).

NOTE: Do not change gears when the tool is running. Always allow

the drill to come to a complete stop before changing gears. If you

are having trouble changing gears, make sure that the dual range

gear shifter is either completely pushed forward or completely

pushed back.

Worklight (Fig. 2)

There is a worklight (E) located just above the trigger switch (A).

The worklight is activated when the trigger switch is depressed,

and will automatically turn off 20 seconds after the trigger switch

is released. If the trigger switch remains depressed, the worklight

will remain on.

NOTE: The worklight is for lighting the immediate work surface and

is not intended to be used as a flashlight.

Keyless Single Sleeve Chuck (Fig. 3–5)

WARNING: Do not attempt to tighten drill bits (or any other

accessory) by gripping the front part of the chuck and turning

the tool on. Damage to the chuck and personal injury may result.

Always lock off trigger switch and disconnect tool from power

source when changing acces sories.

WARNING: Always ensure the bit is secure before starting the

tool. A loose bit may eject from tool causing possible personal

injury.

Your tool features a keyless chuck (F) with one rotating sleeve for

one-handed operation of the chuck. To insert a drill bit or other

accessory, follow these steps.

1. Turn tool off and disconnect tool from power source.

2. Grasp the black sleeve of the chuck with one hand and

use the other hand to secure the tool. Rotate the sleeve

counterclockwise far enough to accept the desired accessory.

3. Insert the accessory about 3/4" (19 mm) into the chuck and

tighten securely by rotating the chuck sleeve clockwise with

one hand while holding the tool with the other. Your tool is

equipped with an automatic spindle lock mechanism. This

allows you to open and close the chuck with one hand.

Be sure to tighten chuck with one hand on the chuck sleeve and

one hand holding the tool for maximum tightness.

To release the accessory, repeat steps 1 and 2 above.

English

FIG. 4 FIG. 5

FIG. 3

Belt Hook and Bit Clip

(Optional Accessory) (Fig. 2)

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making

any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

WARNING: To reduce the risk of serious personal injury,

DO NOT suspend tool overhead or suspend objects from the belt

hook. ONLY hang tool’s belt hook from a work belt.

WARNING: To reduce the risk of serious personal injury,

ensure the screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the belt hook or bit clip

(bit clip sold separately), use only the screw (H) that is provided. Be

sure to securely tighten the screw.

The belt hook (G) and bit clip (I) can be be attached to either side of

the tool using only the screw (H) provided, to accommodate left- or

right- handed users. If the hook or bit clip is not desired at all, it can

be removed from the tool.

To move belt hook or bit clip, remove the screw (H) that holds it in

place then reassemble on the opposite side. Be sure to securely

tighten the screw.

OPERATION

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making

any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Installing and Removing the Battery

Pack (Fig. 6)

NOTE: For best results, make sure your battery pack is fully

charged.

To install the battery pack (K)

FIG. 6

into the tool handle, align the

battery pack with the rails

inside the tool’s handle and

slide it into the handle until the

battery pack is firmly seated in

the tool and ensure that it

does not disengage.

To remove the battery pack

from the tool, press the

release button (J) and firmly

pull the battery pack out of the

tool handle. Insert it into the charger as described in the charger

section of this manual.

Drilling (Fig. 7)

NOTICE: If drilling thin material, use a wood “back-up” block to

prevent damage to the material.

1. Select the desired speed/torque range using the gear shifter to

match the speed and torque to the planned operation. Turn the

collar (C) to the drill symbol.

2. Use sharp drill bits only. For MASONRY, such as brick, cement,

cinder block, etc., use carbide-tipped bits rated for percussion

drilling.

English

3. Always apply pressure in a FIG. 7

straight line with the bit. Use

enough pressure to keep drill

biting, but do not push hard

enough to stall the motor or

deflect the bit.

4. Hold tool firmly with both hands

to control the twisting action of

the drill. If model is not equipped

with side handle, grip drill with

one hand on the handle and

one hand on the battery pack.

WARNING: Drill may stall if overloaded causing a sudden twist.

Always expect the stall. Grip the drill firmly to control the twisting

action and avoid injury.

5. IF DRILL STALLS, it is usually because it is being overloaded

or improperly used. RELEASE TRIGGER IMMEDIATELY,

remove drill bit from work, and determine cause of stalling. DO

NOT DEPRESS TRIGGER ON AND OFF IN AN ATTEMPT

TO START A STALLED DRILL — THIS CAN DAMAGE THE

DRILL.

6. To minimize stalling or breaking through the material, reduce

pressure on drill and ease the bit through the last fractional part

of the hole.

. Keep the motor running when pulling the bit back out of a

drilled hole. This will help prevent jamming.

Screwdriving (Fig. 8)

1. Select the desired speed/torque

FIG. 8

range using the gear shifter to

match the speed and torque to

the planned operation.

2. Turn the torque adjustment

collar (C) to the desired position.

NOTE: Use the lowest torque

setting required to seat the

fastener at the desired depth. The lower the number, the lower

the torque output.

3. Insert the desired fastener accessory into the chuck as you

would any drill bit.

4. Make some practice runs in scrap or on unseen areas of

the workpiece to determine the proper position of the torque

adjustment collar.

5. Always start with lower torque settings, then advance to higher

torque settings to avoid damage to the workpiece or fastener.

Hammerdrilling (Fig. 9)

1. Select the desired speed/torque FIG. 9

range using the gear shifter to

match the speed and torque to

the planned operation. Turn the

collar (C) to the hammerdrill

symbol.

IMPORTANT: Use carbide-

tipped or masonry bits rated for

percussion drilling only.

2. Drill with just enough force on

the hammer to keep it from

bouncing excessively or "rising" off the bit. Too much force will

cause slower drilling speeds, overheating, and a lower drilling

rate.

3. Drill straight, keeping the bit at a right angle to the work. Do not

exert side pressure on the bit when drillling as this will cause

clogging of the bit flutes and a slower drilling speed.

4. When drilling deep holes, if the hammer speed starts to drop

off, pull the bit partially out of the hole with tool still running to

help clear debris from the hole.

NOTE: A smooth, even flow of dust from the hole indicates proper

drilling rate.

English

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

turn tool off and remove the battery pack before making

any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry

air at least once a week. To minimize the risk of eye injury, always

wear ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do

not use water or any cleaning solutions.

Accessories

WARNING: Since accessories, other than those offered by

DEWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk

of injury, only DEWALT recommended accessories should be used

with this product.

Recommended accessories for use with your tool are available at

extra cost from your local dealer or authorized service center. If you

need assistance in locating any accessory, please contact DEWALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286,

call 1-800-4-DEWALT (1-800-433-9258) or visit our website: www.

dewalt.com.

MAXIMUM RECOMMENDED CAPACITIES

DCD780 DCD785

WOOD

Auger 7/8" (22 mm) 7/8" (22 mm)

Paddle 1-1/4" (32 mm) 1-1/4" (32 mm)

Twist 1/2" (13 mm) 1/2" (13 mm)

Self-feed 1-3/8" (35 mm) 1-3/8" (35 mm)

Hole saw 2" (50 mm) 2" (50 mm)

METAL

Twist 1/2" (13 mm) 1/2" (13 mm)

Hole saw 1-3/8" (35 mm) 1-3/8" (35 mm)

MASONRY

Carbide – 1/4" (6.5 mm)

Repairs

The charger and battery pack are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment (including brush inspection and replacement)

should be performed by a DEWALT factory service center, a

DEWALT authorized service center or other qualified service

personnel. Always use identical replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

English

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership

will serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty

materials or workmanship for three years from the date of purchase.

This warranty does not cover part failure due to normal wear or tool

abuse. For further detail of warranty coverage and warranty repair

information, visit www.dewalt.com or call 1-800-4-DEWALT (1-800-

433-9258). This warranty does not apply to accessories or damage

caused where repairs have been made or attempted by others.

This warranty gives you specific legal rights and you may have other

rights which vary in certain states or provinces.

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180,

DCB120, DCB127, DCB201, DCB203 and DCB207

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204, DCB205

DEWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. DEWALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted

by law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

DEWALT Power Tool, Laser, or Nailer for any reason, you can return

it within 90 days from the date of purchase with a receipt for a full

refund – no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the

local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-DEWALT (1-800-433-

9258) for a free replacement.

Français

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger

pour chaque mot-indicateur employé. Lire le mode d’emploi

et porter une attention particulière à ces symboles.

DANGER: indique une situation dangereuse imminente

qui, si elle n’est pas évitée, entraînera la mort ou des

blessures graves.

AVERTISSEMENT : indique une situation

potentiellement dangereuse qui, si elle n’est pas évitée,

pourrait entraîner la mort ou des blessures graves.

ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner

des blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque

de dommages corporels mais qui par contre, si rien

n’est fait pour l’éviter, pourrait poser des risques de

dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET

OUTIL OU DE TOUT AUTRE OUTIL DEWALT, COMPOSEZ LE

NUMÉRO SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures,

lire le mode d’emploi de l’outil.

Avertissements de sécurité généraux

pour les outils électriques

AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect des

avertissements et des directives pourrait se solder par un

choc électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN USAGE

ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se

rapporte à votre outil électrique à alimentation sur secteur (avec fil)

ou par piles (sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux

encombrés ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un

milieu déflagrant, tel qu’en présence de liquides, de

gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la

poussière ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une distraction

pourrait en faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre

à la prise. Ne jamais modifier la fiche d’aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera

réduit par l’utilisation de fiches non modifiées correspondant

à la prise.

b) Éviter tout contact physique avec des surfaces mises

à la terre comme des tuyaux, des radiateurs, des

cuisinières et des réfrigérateurs. Le risque de choc

électrique est plus élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à

l’humidité. La pénétration de l’eau dans un outil électrique

augmente le risque de choc électrique.

Français

d) Ne pas utiliser le cordon de façon abusive. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher

un outil électrique. Tenir le cordon éloigné de la chaleur,

de l’huile, des bords tranchants et des pièces mobiles.

Les cordons endommagés ou enchevêtrés augmentent les

risques de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se

servir d’une rallonge convenant à cette application.

L’utilisation d’une rallonge conçue pour l’extérieur réduira les

risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil

électrique dans un endroit humide, brancher l’outil

dans une prise ou sur un circuit d’alimentation dotés

d’un disjoncteur de fuite à la terre (GFCI). L’utilisation de

ce type de disjoncteur réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique est

utilisé. Ne pas utiliser d’outil électrique en cas de

fatigue ou sous l’influence de drogues, d’alcool ou de

médicaments. Un simple moment d’inattention en utilisant

un outil électrique peut entraîner des blessures corporelles

graves.

b) Utiliser des équipements de protection individuelle.

Toujours porter une protection oculaire. L’utilisation

d’équipements de protection comme un masque

antipoussière, des chaussures antidérapantes, un casque

de sécurité ou des protecteurs auditifs lorsque la situation le

requiert réduira les risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position d’arrêt avant

de relier l’outil à une source d’alimentation et/ou

d’insérer un bloc-piles, de ramasser ou de transporter

l’outil. Transporter un outil électrique alors que le doigt

repose sur l’interrupteur ou brancher un outil électrique dont

l’interrupteur est à la position de marche risque de provoquer

un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer

l’outil. Une clé ou une clé de réglage attachée à une partie

pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre

en tout temps. Cela permet de mieux maîtriser l’outil

électrique dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de

vêtements amples ni de bijoux. Garder les cheveux,

les vêtements et les gants à l’écart des pièces mobiles.

Les vêtements amples, les bijoux ou les cheveux longs

risquent de rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement

de dispositifs de dépoussiérage et de ramassage,

s’assurer que ceux-ci sont bien raccordés et utilisés.

L’utilisation d’un dispositif de dépoussiérage peut réduire les

dangers engendrés par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil électrique

approprié effectuera un meilleur travail, de façon plus sûre et

à la vitesse pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur

est défectueux. Tout outil électrique dont l’interrupteur est

défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/

ou du bloc-piles de l’outil électrique avant de faire

tout réglage ou changement d’accessoire ou avant

de ranger l’outil. Ces mesures préventives réduisent les

risques de démarrage accidentel de l’outil électrique.

d) Ranger les outils électriques hors de la portée des

enfants et ne permettre à aucune personne n’étant pas

familière avec un outil électrique ou son mode d’emploi

Français

d’utiliser cet outil. Les outils électriques deviennent

dangereux entre les mains d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces

mobiles sont mal alignées ou coincées, si des pièces

sont brisées ou présentent toute autre condition

susceptible de nuire au bon fonctionnement de l’outil

électrique. En cas de dommage, faire réparer l’outil

électrique avant toute nouvelle utilisation. Beaucoup

d’accidents sont causés par des outils électriques mal

entretenus.

f) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles à

maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en

tenant compte des conditions de travail et du travail

à effectuer. L’utilisation d’un outil électrique pour toute

opération autre que celle pour laquelle il a été conçu est

dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) Ne recharger l’outil qu’au moyen du chargeur précisé

par le fabricant. L’utilisation d’un chargeur qui convient à

un type de bloc-piles risque de provoquer un incendie s’il est

utilisé avec un autre type de b loc-piles.

b) Utiliser les outils électriques uniquement avec les

blocs-piles conçus à cet effet. L’utilisation de tout autre

bloc-piles risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné

des objets métalliques, notamment des trombones,

de la monnaie, des clés, des clous, des vis ou autres

petits objets métalliques qui peuvent établir une

connexion entre les deux bornes. Le court-circuit des

bornes du bloc-piles risque de provoquer des brûlures ou un

incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors

du bloc-piles; éviter tout contact avec ce liquide. Si

un contact accidentel se produit, laver à grande eau.

Si le liquide entre en contact avec les yeux, obtenir

également des soins médicaux. Le liquide qui gicle hors

du bloc-piles peut provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de

rechange identiques. Cela permettra de maintenir une

utilisation sécuritaire de l’outil électrique.

Avertissements de sécurité relatifs au

marteau perforateur/perceuse/visseuse

• Porter une protection auditive lors du perçage à

percussion. Le bruit en émanant pourrait occasionner une

perte de l’acuité auditive.

• Utiliser la/les poignée(s) auxiliaire(s) si fournie(s) avec

l’outil. Une perte de contrôle de l’outil pourrait occasionner des

dommages corporels.

• Tenir l’outil par les surfaces isolées prévues à cet effet

pendant toute utilisation où l’organe de coupe pourrait

entrer en contact avec des fils électriques cachés. Tout

contact de l’organe de coupe avec un fil sous tension mettra

les parties métalliques exposées de l’outil sous tension et

électrocutera l’utilisateur.

• Utiliser des brides de fixation ou tout autre dispositif de

fixation pratique permettant de soutenir et de retenir la

pièce sur une plate-forme stable. Tenir la pièce avec la main

ou contre le corps rend la pièce instable et risque de provoquer

une perte de maîtrise de l’outil.

• Porter des lunettes de sécurité ou une autre protection

oculaire. Le martelage et la perforation peuvent projeter des

fragments. Les particules projetées peuvent endommager les

yeux irréversiblement.

Français

• Les accessoires et l’outil peuvent devenir brûlants au

toucher pendant l’utilisation. Porter des gants pendant leur

utilisation pour effectuer des travaux produisant beaucoup de

chaleur comme la perforation à percussion et le perçage des

métaux.

• Ne pas utiliser cet outil pendant des périodes de temps

prolongées. Les vibrations causées par la percussion peuvent

poser des risques pour les mains ou les bras. Porter des gants

pour amortir les vibrations, et pour limiter les risques, faire des

pauses fréquentes.

• Prendre des précautions à proximité des évents, car

ils cachent des pièces mobiles. Vêtements amples, bijoux

ou cheveux longs risquent de rester coincés dans ces pièces

mobiles.

AVERTISSEMENT: porter SYSTEMATIQUEMENT des lunettes

de protection. Les lunettes courantes NE sont PAS des lunettes de

protection. Utiliser aussi un masque antipoussières si la découpe

doit en produire beaucoup. PORTER SYSTÉMATIQUEMENT UN

ÉQUIPEMENT DE SÉCURITÉ HOMOLOGUÉ:

• Protection oculaire ANSI Z87.1 (CAN/CSA Z94.3);

• Protection auditive ANSI S12.6 (S3.19);

• Protection des voies respiratoires NIOSH/OSHA/MSHA.

AVERTISSEMENT: les scies, meules, ponceuses, perceuses

ou autres outils de construction peuvent produire des poussières

contenant des produits chimiques reconnus par l’État californien

pour causer cancers, malformations congénitales ou être nocifs au

système reproducteur. Parmi ces produits chimiques, on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment, ou autres

produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un traitement

chimique.

Le risque associé à de telles expositions varie selon la fréquence à

laquelle on effectue ces travaux. Pour réduire toute exposition à ces

produits: travailler dans un endroit bien aéré, en utilisant du matériel

de sécurité homologué, tel un masque antipoussières spécialement

conçu pour filtrer les particules microscopiques.

• Limiter toute exposition prolongée avec les poussières

provenant du ponçage, sciage, meulage, perçage ou

toute autre activité de construction. Porter des vêtements

de protection et nettoyer à l’eau savonneuse les parties

du corps exposées. Le fait de laisser la poussière pénétrer

dans la bouche, les yeux ou la peau peut favoriser l’absorption

de produits chimiques dangereux.

AVERTISSEMENT : cet outil peut produire et/ou répandre

de la poussière susceptible de causer des dommages sérieux et

permanents au système respiratoire. Utiliser systématiquement un

appareil de protection des voies respiratoires homologué par le

NIOSH ou l’OSHA. Diriger les particules dans le sens opposé au

visage et au corps.

AVERTISSEMENT : pendant l’utilisation, porter

systématiquement une protection auditive individuelle

adéquate homologuée ANSI S12.6 (S3.19). Sous certaines

conditions et suivant la durée d’utilisation, le bruit émanant de ce

produit pourrait contribuer à une perte de l’acuité auditive.

ATTENTION: après utilisation, ranger l’outil sur son côté,

sur une surface stable, là où il ne pourra ni faire trébucher ni

faire chuter quelqu’un. Certains outils équipés d’un large bloc-

piles peuvent tenir à la verticale sur celui-ci, mais manquent alors

de stabilité.

• L’étiquette apposée sur votre outil peut inclure les symboles

suivants. Les symboles et leur définition sont indiqués ci-après:

V ................... volts A ....................... ampères

Hz ................. hertz W ...................... watts

min ............... minutes ou AC .......... courant

ou DC ... courant continu ......................... alternatif

La page charge ...

DeWalt DCD780B Le manuel du propriétaire

Marque: DeWalt

Modèle: DCD780B

Catégorie: Perceuses mixtes sans fil

Taper: Le manuel du propriétaire

Ce manuel convient également à

DCD780C2

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCD780B Owner's manual
español: DeWalt DCD780B El manual del propietario

DeWalt DCD780B Le manuel du propriétaire

Ce manuel convient également à

DeWalt DCD780B Le manuel du propriétaire

dans d''autres langues

Documents connexes