Modern Forms BL-20922 Beam Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
209- Task Lamp
BL-20922
- Read all instructions before installing.
- System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
- When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
- Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie.
Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Mounting Screw
Qty: 1 Extra
B
Wire Connector
Qty: 3pcs+1 Extra
A
C D
QTY:1Extra
QTY:1Extra
Conversion plate
Mounting Ring
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE BEGINNING.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal areas
clean all external surfaces of the fixture once every two weeks with a wet cloth.
- Lisez toutes les instructions avant l’installation.
- Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements
locaux.
- Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons aux
clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec un chiffon
humide.
2
INSTALLATION INSTRUCTIONS
209- Task Lamp
BL-20922
Fig. 1 MOUNT ON SWITCH BOX
Fig. 2 MOUNT ON JUNCTION BOX
6. Place the xture over the mounting plate, and secure it with mounting screw (B).
7. This lamp features a dimmer switch. Press and release it to turn on / o. When xture is on, press and hold the switch to cycle from
OR
3. Remove the mounting screw (B) from the fixture.
4. Connect the driver's input wire to junction box wires as
shown (Fig. 3). Make sure that all wire connectors (A) are
secure. If your outlet box has a green or bare cooper ground
wire, connect the fixture’s ground wire to it. Otherwise,
connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected,
tuck them carefully inside the switch box.
5. Secure the mounting plate to the switch box using the
screws provided with the switch box.
1. Shut off the power at the circuit breaker and remove
existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the
parts on a clear area. Be careful not to lose any small
parts necessary for installation.
PREPARATION
dim to bright and release when desired brightness is reached.
MOUNT ON 2”X4” SWITCH BOX (Fig. 1)
3. Remove the mounting screw (B) from the xture.
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Switch Box
Mounting Plate
Fixture
Mounting Screw
Switch Box Screw
Wire Connector
Ground Wire
A
B
Switch
Driver
JunctionBoxScrew
Mounting Ring
Conversion Plate
Mounting Plate
Mounting Screw
B
Ground Wire
JunctionBox
Fixture
C
D
Switch
Driver
INSTALLATION
MOUNT ON 2”X4” SWITCH BOX (Fig. 1)
NOTE: The side of the mounting plate marked "GND" must face out.
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 3 Wiring
4. Connect the driver's input wire to junction box wires as shown (Fig. 3). Make sure that all wire connectors (A) are secure. If your
outlet box has a green or bare cooper ground wire, connect the fixture’s ground wire to it. Otherwise, connect the fixture’s ground
wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the switch box.
5. Secure the mounting ring to the switch box using the junction box screw. Make sure the two holes (spacing 2-3/4") are horizontal as
shown (Fig. 2).
6. Secure the mounting plate (C) and conversion plate (D) to the mounting ring with assembly screw.
7. Place the fixture over the mounting plate, and secure it with mounting screw (B).
8. This lamp features a dimmer switch. Press and release to turn on / off. When fixture is on, press and hold the switch to cycle from
dim to bright and release when desired brightness is reached.
3
INSTALLATION INSTRUCTIONS
209- Task Lamp
BL-20922
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Conversion Plate Dimensions
Back Plate DimensionsMounting Ring Dimensions
NOTE: The side of the mounting plate marked "GND" must face out.
-
1
-
2
-
3
Modern Forms BL-20922 Beam Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms PD-52708 Marimba Mode d'emploi
-
-
-
-
-
-
-
-
-