Access Lighting 28030-1C-BS/AMB Mode d'emploi
- Taper
- Mode d'emploi
CERTIFICATION: cULus DRY
NO. 23089FC
1
INSTALLATION INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that you
carefully read through this instruction sheet. Save this instruction sheet and
refer to it when additions to or changes in the fixture configuration are made
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans la
configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE
CONTSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION
PERTINENT, PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET
SON FONCTIONNEMENT AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this manual
are not meant to cover all possible conditions and situations that may occur. It
must be understood that common sense, caution and care, are factors that
can’t be built into any product. These factors must be supplied by the person(s)
caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux. Do
not install any fixture assembly closer than 6 inches from any curtain or
similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute surface
combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.”
COLLECTION
APPLICATION
MODEL NO.
SYDNEY
Pendant
23089FC
WHAT WE PROVIDE
WHAT YOU NEED
• Mounting Hardware
• Fixture Assembly
• Crossbar
• Screwdriver
• Wire Cutters
• Wiring Supplies as Specified
by Electrical Code
• 1 x A19 E-26 incandescent
bulb
• 1 x Glass shade
GENERAL INFORMATION
STEP BY STEP INSTRUCTIONS
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
recognized.
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the light
off at the light switch is not sufficient to prevent electrical shock.
Dimmable fixture - see attached list for compatible dimmer switches
CERTIFICATION: cULus DRY
NO. 23089FC
2
1
PREPARE FIXTURE
If there is an existing fixture remove it. Expose the supply
wires from the J-box. Cut and trim any excess wire
leaving enough wire for electrical connections. If you need
to adjust the length of the cable, release the cord strain
relief first, then adjust to desired length. Reinstate the
cord strain relief. Mount the crossbar to the J-box utilizing
the 2 supplied mounting screws.
2
MAKE THE WIRE CONNECTIONS
Gently pull the supply wires through the hole in the
crossbar plate. Connect the black supply wire to the black
fixture wire. Secure with the supplied wire nuts. Connect
the white supply wire to the white fixture wire. Secure with
the supplied wire nuts. Attach the green J-Box wire
around green hexagonal head screw or connect it to the
green supply grounding wire of the fixture. Secure all
wires with electrical tape (not supplied).Tuck all wires
carefully into the J-box
3
SECURE CANOPY & GLASS SHADE
AND INSERT BULB
Position the canopy over the crossbar such that the holes
on the sides of the canopy line up with the holes in the
crossbar. Secure the canopy to the crossbar with the
supplied screws. Remove retaining ring, place the glass
(not included) over socket, and secure with the glass
retaining ring.
Insert the bulb.
DO NOT EXCEED THE MAXIMUM WATTAGE
AS STATED ON THE WARNING LABEL.
4
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR NEW
ACCESS LIGHTING FIXTURE
Cord strain relief
Glass
retaining ring
Glass shade
(not included)
CERTIFICATION: cULus DRY
NO. 23089FC
3
CERTIFICATION: cULus DRY
NO. 23089FC
4
CERTIFICATION: cULus DRY
NO. 23089FC
5
-
1
-
2
-
3
-
4
-
5
Access Lighting 28030-1C-BS/AMB Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Access Lighting TaskWorks Flex 72002LEDD Guide d'installation
-
Access Lighting 20292LEDDLP-SAT/FST Manuel utilisateur
-
-
-
-
-
-
-
-