DeWalt DXCMTA5590412 Mode d'emploi

DXCMTA5590412

Gas Portable Air Compressor

Gaz de compresseur portatif

Gas de compresor portátil

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-888-895-4549 • www.dewalt.com

MAT Industries, LLC, Long Grove, IL 60047

2

English

Air Compressor

A. Pump Air Intake Filter

B. Engine Air Filter

C. Engine On/Off Switch

D. Air Tank Pressure Gauge

E. Regulated Pressure Gauge

F. Pressure Regulator

G. Air Outlet

H. Unloader Valve

I. Safety Valve

J. Air Tank Drain Valve(s)

K. Fixed Throttle

L. Choke Control

M. Fuel Valve Lever

N. Starter Grip

Pump Specications

Oil-Free

Single stage

Direct Drive

Engine Specications

Honda 163 cc

Internal Combustion

4-stroke

Actual unit may vary slightly.

FIG. 1

A

B

J

G

F

E

D

H

I

J

N

L

M

K

C

3

English

Specications

MODEL DXCMTA5590412

WEIGHT 93 lbs. (42.2 kg)

HEIGHT 22.1" (561 mm)

WIDTH 21.6" (549 mm)

LENGTH 24.4" (620 mm)

AIR TANK CAPACITY 4 gallons (15.1 liters)

APPROX. BLOW OFF PRESSURE

155 psi

SCFM @ 90 PSI

5.0 *

* Tested per ISO 1217

Hot Surfaces

Denitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and pay

attention to these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor or

moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT:

1-888-895-4549

Important Safety Instructions

DANGER: Carbon Monoxide. Using an engine indoors can

kill you in minutes. Engine exhaust contains high levels of

carbon monoxide (CO), a poisonous gas you cannot see or

smell. You may be breathing CO even if you DO NOT smell

engine exhaust.

OUTLET TUBE

ENGINE

MUFFLER

GASOLINE

ENGINE

FIG. 2

4

English

• NEVER use an engine inside homes, garages, crawlspaces,

or other partly enclosed areas. Deadly levels of carbon mon-

oxide can build up in these areas. Using a fan or opening

windows and doors does NOT supply enough fresh air.

• ONLY use outdoors and far away from open windows, doors

and vents. These openings can pull in engine exhaust.

• Even when the engine is used correctly, CO may leak into

your home. ALWAYS use a battery-powered or battery

backup CO alarm (not supplied) in the home. Read and fol-

low all directions for CO alarm before using. If you start to

feel sick, dizzy or weak at anytime, move to fresh air imme-

diately. See a doctor. You could have carbon monoxide

poisoning.

WARNING: Do not operate this unit until you read this

instruction manual and the engine instruction manual for safety,

operation and maintenance instructions.

WARNING: This product may not be equipped with a spark-

arresting muffler. If the product is not equipped and will be used

around flam ma ble ma teri als or on land covered with materials such

as agricultural crops, forest, brush, grass or other similar items,

then an ap proved spark arrester must be installed and is legally

required in the state of California. It is a violation of California statutes

section 130050 and/or sec tions 4442 and 4443 of the California

Public Re sourc es Code, unless the engine is equipped with a spark

arrester, as defined in section 4442, and maintained in ef fec tive

work ing order. Spark arresters are also required on some U.S.

For est Service land and may also be legally required under other

statutes and or di nanc es.

WARNING: CONTAINS LEAD. May be harmful if eaten or

chewed. May generate dust containing lead. Wash hands after

use. Keep out of reach of children.

WARNING: This product can expose you to chemicals

including Lead, which is known to the State of California to cause

cancer and birth defects or other reproductive harm. For more

information go to www.P65Warnings.ca.gov.

WARNING: The engine exhaust from this product contains

chemicals known to the State of California to cause cancer, birth

defects or other reproductive harm.

SAVE THESE INSTRUCTIONS

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Spilled gas o line and it’s

vapors can be come ignited

from cigarette sparks, elec-

trical arcing, exhaust gas es

and hot engine components

such as the muffler.

• Shut off en gine and allow it to

cool before adding fuel to the

tank.

• Use care in fill ing tank to avoid

spill ing fuel. Move unit away

from fueling area before start-

ing en gine.

• Heat will ex pand fuel in the

tank which could result in

spillage and pos si ble fire or

explosion.

• Keep maximum fuel level

1/2" (12.7 mm) be low

bottom of filler neck

to allow for expansion.

5

English

• Combustible materials

which come into contact

with hot engine parts can

become ignited.

• Add fuel outdoors in a well

ventilated area. Make sure

there are no sources of igni-

tion, such as cigarettes near

refueling location.

• Operate compressor in a

clean, dry, well ventilated area

a minimum of 48" (1.22 m)

from any building, object

or wall. Do not operate unit

indoors or in any confined

area.

• Operate compressor in an

open area away from dry

brush, weeds or other com-

bustible materials.

• Improperly stored fuel could

lead to acciden tal ignition.

Fuel im prop er ly secured

could get into the hands of

children or oth er un qual i fied

persons.

• Store fuel in an OSHA-ap-

proved con tain er, in a se cure

location away from work area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce the

risk of fire, do not allow

the compressor to operate

unattended.

• Always remain in attendance

with the product when it is

operating.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Breathing ex haust fumes

will cause se ri ous injury

or death! En gine exhaust

con tains carbon mon ox ide,

an odorless and deadly gas.

• Always operate air compressor

outside in a clean, well

ventilated area. Avoid enclosed

areas such as garages,

basements, storage sheds,

which lack a steady exchange

or air. Keep children, pets

and others away from area of

operation.

• The compressed air directly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminants can cause

serious injury or death.

• Never use air obtained directly

from the compressor to supply

air for human consumption.

The compressor is not

equipped with suitable filters

and in-line safety equipment

for human consumption.

6

English

• Exposure to chemicals

in dust created by

power sanding, sawing,

grinding, drilling and other

construction activities may

be harmful.

• Sprayed materials such as

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or

safety data sheets for the

materials you are spraying.

Always use certified safety

equipment: NIOSH/OSHA

respiratory protection or

properly fit ting face mask

designed for use with your

specific application.

WARNING: RISK OF BURSTING

Air Tank: On February 26, 2002, the U.S. Consumer Product

Safety Commission published Release # 02-108 concerning air

compressor tank safety:

Air compressor receiver tanks do not have an infinite life. Tank life

is dependent upon several factors, some of which include oper-

ating conditions, ambient conditions, proper installations, field

modifications, and the level of maintenance. The exact effect of

these factors on air receiver life is difficult to predict.

If proper maintenance procedures are not followed, internal corro-

sion to the inner wall of the air receiver tank can cause the air tank

to unexpectedly rupture allowing pressurized air to suddenly and

forcefully escape, posing risk of injury to consumers.

Your compressor air tank must be removed from service by the

end of the year shown on your tank warning label.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drain air tank daily or after each

use. If air tank develops a leak,

replace it immediately with

a new air tank or replace the

entire compressor.

• Modifications or attempted

repairs to the air tank. • Never drill into, weld or make

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorized modifications

to the unloader valve,

safety valve, or any other

components which control air

tank pressure.

• The air tank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

Attachments & accessories:

• Exceeding the pressure rating

of air tools, spray guns, air

operated accessories, tires

and other inflatables can

cause them to explode or

fly apart, and could result in

serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum allowable

pressure rating of attachments.

Never use compressor to

inflate small low pressure

objects such as children’s toys,

footballs, basketballs, etc.

7

English

Tires:

• Over inflation of tires could

result in serious injury and

property damage.

• Use a tire pressure gauge to

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE: Air tanks, compressors

and similar equipment used to

inflate tires can fill small tires

very rapidly. Adjust pressure

regulator on air supply to no

more than the rating of the tire

pressure. Add air in small incre-

ments and frequently use the

tire gauge to prevent over infla-

tion.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream

can cause soft tissue damage

to exposed skin and can

propel dirt, chips, loose

particles and small objects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

• Always turn the compressor

off and bleed pressure from

the air hose and air tank before

attempting maintenance,

attaching tools or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal such

as the engine head, engine

exhaust or outlet tubes, can

result in serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

8

English

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The engine can start

accidentally if the flywheel is

turned by hand or moved by

pulling on the starter rope.

• Always disconnect the spark

plug and bleed pressure from

the air tank before performing

maintenance.

• Moving parts such as the

pulley, flywheel, and belt can

cause serious injury if they

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which are

damaged or removed.

• Keep your hair, clothing and

gloves away from moving parts.

Loose clothes, jewelry or long

hair can be caught in moving

parts.

• Air vents may cover moving

parts and should be avoided as

well.

• Attempting to operate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in serious

injury.

• Any repairs required on this

product should be performed

by a DeWALT factory service

center or a DeWALT authorized

service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your air

compressor could lead to

se ri ous in ju ry or death to you

or others.

• Review and understand all

instructions and warnings in

this manual.

• Be come fa mil iar with the op er-

a tion and con trols of the air

compressor.

• Keep operating area clear of all

persons, pets, and obstacles.

• Keep chil dren away from the air

compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea tures

of this prod uct.

• Equip area of operation with a

fire extinguisher.

• Do not op er ate machine with

missing, broken, or un au tho-

rized parts.

• Never stand on the

compressor.

9

English

WARNING: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute

to hearing loss.

• Always wear certified safety

equipment: ANSI S12.6

(S3.19) hearing protection.

WARNING:

RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Serious injury can result from

attempting to lift too heavy

an object.

• The compressor is too heavy

to be lifted by one person.

Obtain assistance from others

before lifting.

WARNING: RISK OF INJURY OR PROP ER TY DAMAGE WHEN

TRANSPORTING OR STORING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Oil can leak or spill and could

result in fire or breathing

hazard; serious injury or

death can result. Oil leaks will

damage carpet, paint or other

surfaces in vehicles or trailers.

• Always place compressor

on a protective mat when

transporting to protect against

damage to vehicle from leaks.

Remove compressor from

vehicle immediately upon

arrival at your destination.

Always keep compressor level

and never lie on its side.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

10

English

I

FEATURES

UNLOADER VALVE

When the maximum air tank pressure is obtained, the unloader

valve (H) will blow-off. This will cause the compressor to exhaust

the air to the atmosphere and not the tank. The valve is preset by

the manu facturer and must not be removed or modified in any way.

Manual Lock: The manual lock allows you to manually unload the

compressor with air pressure in the air tank. To operate the manual

lock:

Rotate the manual lock unloader lever to the

OPEN

H

CLOSED

H

open position to prevent air tank pressure

buildup. Rotate manual lock unloader lever to

the closed position after starting the engine

to allow air tank pressure to build. NOTE: Air

will not build in tank when manual lock

unloader lever in the open position.

SAFETY VALVE

This valve (I) is designed to prevent system failures

by relieving pressure from the system when the

compressed air reaches a predeter mined level. The

valve is preset by the manu facturer and must not be

removed or modified in any way.

AIR INTAKE FILTER

The filter (A) is designed to clean air entering the pump.

A

To ensure the pump continually receives a clean, cool,

and dry air supply the filter must always be clean and

the filter intake must be free from obstructions.

AIR TANK DRAIN VALVES

The drain valve (J) is used to remove

J

moisture from the air tank after the air

compressor is shut off.

AIR TANK PRESSURE GAUGE

The air tank pressure gauge (D) indicates air pressure in the air tank.

REGULATED PRESSURE GAUGE

The regulated pressure gauge (E) indicates the air ED

F

pressure available at the outlet side of the

regulator. This pressure is controlled by the

regulator and is always less or equal to the air

tank pressure.

REGULATOR

The regulator knob (F) controls the air pressure coming from the air

tank.

To Adjust Regulator:

1. Turn knob clockwise to increase regulated pressure and

counterclockwise to decrease regulated pressure.

WARNING: Risk of Bursting. Too much air pressure causes

a hazardous risk of bursting. Check the manufacturer’s

maximum pressure rating for air tools and accessories. The

regulator outlet pressure must never exceed the maximum

pressure rating.

THROTTLE CONTROL

When maxi mum air tank pres sure is reached and the unloader

valve vents air, it activates the throttle control on the engine. This

gas saving feature holds the engine at a factory-set idling speed

until air pressure in the air tank drops to reset pressure. The

unloader valve then reactivates the throttle control and accelerates

the engine to full throttle.

11

English

INSTALLATION

Assembly (Fig. 1)

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Apply sealant tape to hose threads.

3. Assemble hose to air outlet (G).

NOTICE: Do not assemble splitters directly to the air

outlet (G).

NOTE: Assembling quick connect bodies to air outlet (G) and quick

connect plugs to hose ends make connecting and disconnecting

hoses simple and easy. Quick connect bodies and plugs are

available for purchase from your local dealer or authorized service

center.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 psi.

2. Remove hose(s) from air outlet(s) (G).

Lubrication and Oil

ENGINE

1. The engine was filled WITH oil at the manufacturer. Check

engine oil level before operating unit. If necessary, fill engine

to the appropriate level with recommended oil, see engine's

instruction manual supplied by engine manufacturer for correct

procedure.

2. Add fuel to engine. See engine's instruction manual supplied by

engine manufacturer for correct procedure.

WARNING: Risk of explosion or fire. Gasoline vapor is highly

flammable. Refuel outdoors preferably, or only in well-ventilated

areas. Do not refuel or check gasoline level while the engine is

running. Do not store, spill, or use gasoline near an open flame,

a source of sparks (such as welding), or near operating electrical

equipment.

Compatibility

Air tools and accessories that are run off the compressor must be

compatible with petroleum based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTICE: Always use an air line filter to remove moisture and oil

vapor when spraying paint.

Location

DANGER:

Risk of breathing. Exhaust from the gasoline engine

contains deadly carbon monoxide, which is odorless and toxic.

Operate engine only in well ventilated areas.

NOTICE: Risk of property damage. In order to avoid damaging

the air compressor, do not allow the unit to be tilted more than

10º when operating.

Place air compressor at least 4 feet (1.2 m) away from obstacles

that may prevent proper ventilation. Keep unit away from areas

that have dirt, vapor and volatile fumes in the atmosphere which

may clog and gum up the intake filter and valves, causing inefficient

operation.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable noise

12

English

levels in your area. To reduce excessive noise, use vibration mounts

or silencers, relocate the unit or baffle walls. Contact a D

e

WALT

service center or call 1-888-895-4549 for assistance.

TRANSPORTING

WARNING: Risk injury from lifting. Unit weighs more than 70

lbs. (77.6 kg) Do not move or lift without assistance.

NOTICE:

Risk of property damage.

Place engine fuel valve lever

(M) in the OFF position before moving or transporting unit.

When transporting the compressor in a vehicle, trailer, etc. ensure

that the air tank is drained and the unit is secured and placed on

a protective mat on a flat horizontal surface. DO NOT store in a

standing position.

NOTE: Should the unit tip over, hard starting and smoking will occur

due to oil spillage.

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

3. Ensure the drain valve (J) is closed.

4. Ensure safety valve (I) is functioning properly, see Checking

Safety Valve under Maintenance.

NOTICE:

Do not operate without oil or with inadequate oil. DeWALT

is not responsible for compressor failure caused by inadequate oil.

5. Check engine's oil and fuel level, see engine's instruction manual

for correct procedures.

6. Ensure all guards, covers, and labels are in place, legible (for

labels) and securely mounted. Do not use compressor until all

items have been verified.

Initial Set-up

(Fig. 1)

WARNING: Do not operate this unit until you read and

understand this instruction manual and the engine instruction

manual for safety, operation and maintenance instructions.

BREAK-IN PROCEDURE

NOTICE:

Risk of property damage. Serious damage may result if

the following break-in instructions are not closely followed.

This procedure is required:

• Before the air compressor is used for the first time.

• When the unloader valve has been replaced.

The procedure:

1. Follow Pre-Start Checklist under Preparation for Use.

2. Rotate the unloader's manual lock to the open position to

prevent air tank pressure buildup.

3. Open the pressure regulator. Rotate clockwise until it stops.

WARNING: Do not operate this unit until you read and under-

stand the engine instruction's manual for safety, operation and

maintenance instructions.

4. Prepare engine for first time use, see engine's instruction manual

for correct procedure.

5. Turn the engine ON/OFF switch (C)

OPEN

CLOSED

L

MOFF

ON

to the ON position.

6. Place the fuel valve lever (M) in the

ON postion.

7.

If the engine is cold, move the

choke (L) to the CLOSED position

as shown. If the engine is hot, move

the choke to the OPEN position.

WARNING: Risk of unsafe operation. Pull starter grip slowly

until resistance is felt. Then pull starter grip (N) rapidly to avoid

13

English

kickback and prevent hand or arm injury.

NOTICE: Do not allow the starter grip to snap back. Return it gently

by hand.

NOTE: If the engine does not start, check the oil level and add oil

as needed.

NOTE: To ensure maximum oil lubrication, place the unit on a level

surface.

8. As the engine warms up, move the choke to the OPEN position.

9. Rotate the manual lock on the unloader valve into the closed

position so the air tank pressure can build.

10. Close the pressure regulator. Rotate the regulator knob (F)

counterclockwise to its built-in stop. This will allow air to build

pressure in the air tank.

11. Compressed air will be available from the hose air outlet until it

is used up or bled off.

OPERATING PROCEDURES

Start-up (Fig. 1)

1. Follow Pre-Start Checklist under Preparation for Use.

2. Turn the regulator knob (F) counterclockwise until fully closed.

Regulated pressure gauge should read 0 psi.

3. Rotate the manual lock unloader lever to the open position to

assist with start up.

4. Turn the engine ON/OFF switch (C) to the ON position.

5. Place the fuel valve lever (M) in the ON postion.

6.

If the engine is cold, move the choke (L) to the CLOSED

position as shown. If the engine is hot, move the choke to the

OPEN position.

WARNING: Risk of unsafe operation. Pull starter grip slowly

until resistance is felt. Then pull starter grip (N) rapidly to avoid

kickback and prevent hand or arm injury.

NOTICE: Do not allow the starter grip to snap back. Return it gently

by hand.

NOTE: If the engine does not start, check the oil level and add oil

as needed.

NOTE: To ensure maximum oil lubrication, place the unit on a level

surface.

7. As the engine warms up, move the choke to the OPEN position.

8. Rotate manual lock unloader lever to the closed position to allow

air tank pressure to build. NOTE: Pump will not operate with the

manual lock unloader lever in the open position.

9. Allow compressor to pump up to blow off pressure.

WARNING: Risk of unsafe operation. If any unusual noise

or vibration is noticed, stop the compressor and refer to the

troubleshooting section.

10. Attach hose and accessory.

WARNING: Risk of unsafe operation. Firmly grasp air hose in

hand when installing or disconnecting to prevent hose whip.

WARNING:

Risk of unsafe operation. Do not use damaged or

worn accessories.

NOTICE: Risk of property damages. Compressed air from the unit

may contain wa ter condensation and oil mist. Do not spray un fil-

tered air at an item that could be damaged by moisture. Some air

op er ated tools or de vic es may require filtered air. Read the in struc-

tions for the air tool or device.

11. Adjust regulator (F) to desired setting. See Regulator under

Features.

Shut-down

1. Place the engine ON/OFF switch (C) to the OFF Position.

2. Place the fuel valve lever (M) in the OFF postion.

NOTE: If finished using compressor, follow Steps 3–7.

14

English

3. Turn regulator knob (F) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 psi.

4. Remove hose and accessory.

5. Drain the air tank.

See Draining Air Tank under Maintenance

.

NOTICE:

Risk of property damage.

Place engine fuel valve lever

(M) in the OFF position before moving or transporting unit.

WARNING: Risk of bursting. Drain air tank daily. Water will

condense in air tank. If not drained, water will corrode and weaken

the air tank causing a risk of air tank rupture.

6. Allow the compressor to cool down.

7. Wipe air compressor clean and store in a safe, non freezing area.

MAINTENANCE

WARNING:The following procedures must be followed when

maintenance or service is performed on the air compressor.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Disconnect spark plug wire.

3. Drain air tank.

4. Allow air compressor to cool down before starting service

NOTE: All compressed air systems contain maintenance parts (e.g.

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of

in accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should

be performed by a DeWALT factory service center or a DeWALT

authorized service center.

Maintenance Chart

Procedure

Daily

Weekly

Monthly

1 year or

200 Hours

See tank

warning

label

Check safety valve

X

Inspect air filter

X

+

Drain air tank

X

Oil leak inspection

X

Check for unusual noise/vibration

X

Check for air leaks

X

*

Clean compressor exterior

X

Remove tank from service

X++

Engine See engine instruction manual.

* To check for air leaks apply a solution of soapy water around

joints. While compressor is pumping to pressure and after

pressure cuts out, look for air bubbles to form.

+ Perform more frequent in dusty or humid conditions.

++ For more information, call 1-888-895-4549

Checking Safety Valve (Fig. 1)

WARNING: Hot surfaces. Risk of burn. Pump head, and

surrounding parts are very hot, do not touch (see the Hot

Surfaces identified in Fig. 2). Allow compressor to cool prior

to servicing.

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture

or an explosion.

WARNING: Risk from flying objects. Always wear certified safety

15

English

equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side

shields when using the compressor.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is stuck

or does not operate smoothly, it must be replaced with the same

type of valve.

Checking Air Filter Element (Fig. 1)

WARNING: Hot surfaces. Risk of burn. pump head, and

surrounding parts are very hot, do not touch (see the Hot Surfaces

identified in Fig. 2). Allow compressor to cool prior to servicing.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Allow unit to cool.

5. Remove filter (A).

6. If filter needs cleaning, blow out with air. Replace

if needed. Purchase replacement parts from

your local dealer or authorized service center.

Always use identical replacement parts.

7. Place filter back in filter base.

NOTICE: Risk of unsafe operation. Do not operate without air

inlet filter.

Draining Air Tank (Fig. 1)

WARNING: Risk of unsafe operation. Air tanks contain high

pressure air. Keep face and other body parts away from outlet

of drain. Use eye protection [ANSI Z87.1 (CAN/CSA Z94.3)] when

draining as debris can be kicked up into face.

WARNING: Risk from noise. Use ear protection (ANSI S12.6

(S3.19) as air flow noise is loud when draining.

NOTE: All compressed air systems generate condensation that accu-

mulates in any drain point (e.g., tanks, filter, aftercoolers, dryers). This

condensate contains lubricating oil and/or substances which may be

regulated and must be disposed of in accordance with local, state,

and federal laws and regulations.

1. Ensure engine ON/OFF switch (C) is in the OFF position.

2. Turn the regulator counterclockwise to set the outlet pressure to

zero.

3. Remove the air tool or accessory.

4. Pull ring on safety valve allowing air to bleed from the tank until

tank pressure is approximately 20 psi. Release safety valve ring.

5. Drain water from air tank by opening drain valve (counterclock-

wise) on bottom of tank.

WARNING: Risk of bursting. Water will condense in the air

tank. If not drained, water will corrode and weaken the air tank

causing a risk of air tank rupture.

NOTICE: Risk of property damage. Drain water from air tank may

contain oil and rust which can cause stains.

6. After the water has been drained, close the drain valve (clock-

wise). The air compressor can now be stored.

NOTE: If drain valve is plugged, release all air pressure. The valve

can then be removed, cleaned, then reinstalled.

NOTE: Tilt unit to drain tanks (B).

NOTE: In cold climates, drain the tanks after each use to

reduce problems with freezing of water condensation.

A

16

English

B

ACCESSORIES

Recommended accessories for use with your tool are available for

purchase from your local dealer or authorized service center. If you

need assistance in locating any accessory for your tool, please call

1-888-895-4549 or visit our website www.dewalt.com.

WARNING: The use of any other accessory not recommended

for use with this tool could be hazardous. Use only accessories

rated equal to or higher than the rating of the air compressor.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number ___________

Date and Place of Purchase ____________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

e

WALT factory service

center, a D

e

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

Limited Warranty

DEWALT Industrial Tools are warranted from date of purchase.

1 Year – Limited on all oil-free compressors. This warranty is

not transferable to subsequent owners.

DEWALT will repair or replace, without charge, at DEWALT’s

option, any defects due to faulty materials or workmanship.

For further detail of warranty coverage and warranty repair

information, call 1-(888)-895-4549 or visit dewalt.com. This

warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. This warranty

also does not apply to merchandise sold by DEWALT which has

been manufactured by and identied as the product of another

company, such as gasoline engines. Such manufacturer’s

warranty, if any, will apply. ANY INCIDENTAL, INDIRECT OR

CONSEQUENTIAL LOSS, DAMAGE OR EXPENSE THAT MAY

RESULT FROM ANY DEFECT, FAILURE OR MALFUNCTION OF

THE PRODUCT IS NOT COVERED BY THIS WARRANTY. Some

states do not allow the exclusion of limitation of incidental or

consequential damages, so the above limitation or exclusion may

not apply to you. IMPLIED WARRANTIES, INCLUDING THOSE

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM THE DATE OF

ORIGINAL PURCHASE. Some states do not allow limitations on

how long an implied warranty lasts, so the above limitations may

not apply to you.

17

English

What the Company Will Do: (the company) will cover parts

and labor to remedy substantial defects due to materials

and workmanship during the rst year of ownership, with the

exceptions noted below. Parts used in repair of whole goods or

accessories are warranted for the balance of the original warranty

period.

What is not covered Under This Warranty? Failures by the

original retail purchaser to install, maintain, and operate said

equipment in accordance with standard industry practices.

Modications to the product, or tampering with components,

or failure to comply with the specic recommendations of the

Company set forth in the owner’s manual, will render this warranty

null and void. The Company shall not be liable for any repairs,

replacements, or adjustments to the equipment, or any costs for

labor performed by the purchaser without the Company’s prior

written approval. The effects of corrosion, erosion, surrounding

environmental conditions, cosmetic defects, and routine

maintenance items, are specically excluded from this warranty.

Routine maintenance items such as: oil, lubricants, and air lters,

as well as changing oil, air lters, belt tensioning, etc… fall under

the owner’s responsibility. Additional exclusions include: freight

damage, failures resulting from neglect, accident, or abuse,

induction motors when operated from a generator, oil leaks, air

leaks, oil consumption, leaky ttings, hoses, petcocks, bleeder

tubes, and transfer tubes.

• The following components are considered normal wear

items and are not covered after the rst year of

ownership: Belts, sheaves, ywheels, check valves,

pressure switches, air unloaders, throttle controls,

electric motors, brushes, regulators, o-rings, pressure

gauges, tubing, piping, ttings, fasteners, wheels, quick

couplers, gaskets, seals, air lter housings, piston rings,

connecting rods, and piston seals.

• Labor, service calls, and travel charges, are not covered

after the rst year of ownership on stationary

compressors (compressors without handles, or wheels).

Repairs requiring overtime, weekend rates, or any other

charges beyond the standard shop labor rate are not

covered.

• Time required for orientation training for the service

center to gain access to the product, or additional time

due to inadequate egress.

• Damage caused from inadequate lter maintenance.

• Pump wear or damage caused by any oil contamination.

• Pump wear or valve damage caused by failure to follow

proper maintenance guidelines.

• Gas Engines, if product is equipped with a gas engine,

see engine manual for specic engine manufacturer’s

warranty coverage.

Parts purchased separately: The warranty for parts purchased

separately such as: pumps, motors, etc., are as follows:

From Date of Purchase

• All single & two stage pumps 1 year

• Electric motors 90 days

• Universal motor/pump 30 days

• All other parts 30 days

• No return authorization will be issued for electrical

components once items are installed.

How do You Get Service? In order to be eligible for service

under this warranty you must be the original retail purchaser,

18

English

and provide proof of purchase from one of the Company’s

dealers, distributors, or retail outlet stores. Portable compressors

or components must be delivered, or shipped, to the nearest

Authorized Service Center. All associated freight costs and travel

charges must be borne by the consumer. Please call our toll free

number 1-888-895-4549 for assistance.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND

YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

THE COMPANY MAKES NO OTHER WARRANTY OR

REPRESENTATION OF ANY KIND WHATSOEVER,

EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE. ALL

IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF

MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE

ARE HEREBY DISCLAIMED. LIABILITY FOR CONSEQUENTIAL

AND INCIDENTAL DAMAGES UNDER ANY AND ALL

WARRANTIES, OTHER CONTRACTS, NEGLEGENCE, OR

OTHER TORTS IS EXCLUDED TO THE EXTENT EXCLUSION IS

PERMITTED BY LAW.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-888-895-4549 for a free

replacement.

RISK OF BURSTING

Prévenir la corrosion en

inclinant le réservoir pour

drainer toute humidité

aprés chaque usage.

RIESGO DE EXPLOSIÓN

Prevenir la corrosión del

tanque. Después de cada

uso inclinar el tanque para

drenar toda la humedad.

098-1062

RISQUE D’ÉCLATEMENT

Prevent tank corrosion.

After each usage, tilt tank

to drain all moisture from

tank.

MOISTURE DRAIN

OPEN

DESAGÜE

DE AGUA

ÉVACUATION

D’EAU

Before starting, read and understand operator manual for safe

operation and maintenance. For replacement manual write to:

Compressor Service, 118 West Rock Street, Springfield, MN

56087

Risk of fire or explosion - Gasoline vapor is highly flammable.

Refuel outdoors or in a well-ventilated area. • DO NOT spray

flammable liquid in a confined area or towards a hot surface. •

Spray area must be well-ventilated. • DO NOT smoke while spraying or

spray where spark or flame is present. • Arching parts - Keep

compressor at least 20 feet away from explosive vapors, such as when

spraying with a spray gun.

Risk of bursting - Do not adjust regulator to result in output

pressure greater than marked maximum pressure of attachment.

• RUST WEAKENS TANK, may cause explosion and severe or

fatal injury/property damage. Drain condensed water from tank

after each use to reduce rusting. • DO NOT weld on or repair tank

- replace.

Risk of injury - DO NOT direct air stream at body. • DO NOT

operate with supplied guards removed. • Disconnect sparkplug

and drain all air pressure from tank before servicing and after

each use. DO NOT use compressed air for breathing. Wear eye

protection.

UNLOADER

VALVE

START

RUNNING

Risk of carbon monoxide poisoning - Engine produces deadly

exhaust. DO NOT run compressor in enclosed area.

WARNING 098-2276-C

Avant la mise enmarche, lisez et comprenez le manuel d’opérateur

pour sécurité de fonctionnement et entretien. Pour obtenir un manuel de

remplacement, écrivez le: Compressor Service, 118 West Rock St.,

Springfield, MN 56087

Risques d’incendie ou d’explosion--Les vapeurs d’essence sont

extrêmement inflammables. Remplissez le réservoir de carburant à

l’extérieur ou dans un endroit bien aéré. • Ne pas vaporiser de liquides

inflammables dans un endroit confiné ou vers un superficie chaud. • Les locaux

ou il se fait de la vaporisation doivent etre bien ventiles. • Ne pas fumer lors de la

vaporisation ni vaporiser en presence d’entincelles ou de flammes. • Cet

appareil produit des des arcs électriques--Placer le compresseur à au moins

7 m (20 ft) de vapeurs explosives, comme lors de la vaporisation au pistolet.

Risque d’eclatement--Ne pas regler le regulateur de

pression de sortie a une pression superieure à la pression maxi-

male indiquee pour l’accessoire.• ROUILLE S’AFFAIBLIR DU

RÉSERVOIR, causer l’explosion et des blessures ou la mort/des

dammages matériels. Purgez l’eau condensé du réservoir après

chaque utilisation reduire rouille. • Ne jamis reparer ou souder le

recepteur d’air--remplacez.

Risque de blessure--Ne pas diriger le jet d’air vers

l’operateur. • Débranchez le fil de la bougie d’allumage et

éliminer toute la pression d’air du réservoir avant d’entretenir ce

compresseur et après chaque usage. • Ne jamais faire

fonctionner le modèle sans le protecteur de courroie. • L’air produit par

un compressor n’est pas respirable. • Portez des lunettes de protection.

VALVE DE

DÉCHARGE

DÉMARRAGE

FONCTIONNANT

Risques d’axphyxie par oxyde de carbone--Le moteur produit des

gaz d’échappement mortels. Ne faites jamais fonctionner la machine

dans un endroit clos.

AVERTISSEMENT 098-2277-C

Antes de arrancar la unidad, lea y entienda el manual del operador

por la operación y mantenimiento segura. Para obtener un manual

nuevo escriba: Compressor Service, 118 West Rock Street,

Springfield, MN 56087

Risgo de incendio o explosion--El vapor de gasolina es altamente

inflamable. Llene el combustible afuera, o en un área bien ventilada.

• Nunca rocíe líquidos inflamables dentro de una zona cerrada o

hacia una superficie caliente. • La zona de rociado debe estar bien

ventilada. • Nunca fume al rociar ni rocíe en la presencia de una chispa o

llama. • Este unidad produje arcos electricos--Mantenga el compresor

por lo menos 7 m de los vapores explosives, como cuando rociado con un

pistola de rociar.

Riesgo de estallido--NUNCA ajuste el regulador de modo que la

presión de salida sea mayor que la presión máxima marcada en

el aditamento. • HERRUMBRE DEBILITA EL TANQUE, podría

dar como resultado la explosión y graves lesiones o muerte/

daños a la propiedad. Purgue la agua condensada del tanque

después de cada uso reducir herrumbrando. • Nunca repare ni

suelde el tanque de aire--reemplace.

Riesgo de lesiones--Nunca dirija la corriente de aire hacia el

cuerpo. • Nunca opere la unidad sin las defensas provistas.

• Desconecte el cable de bujía y drene toda la presión de aire del

tanque antes de realizar el servicio a este compresor y después

cada uso. • El aire comprimido no es apto para propósitos de respi-

ración. • Lleve lentes de seguridad.

VALVULA DE

DESCARGA

ARRANQUE

FUNCIONANDO

Riesgo de envenenamiento con monoxido de carbono--El motor

produje los nocivos gases de escape. Nunca se debe hacer

funcionar la unidad en un área cerrada.

ADVERTENCIA 098-2278-C

DANGER DANGER PELIGRO

Using a gasoline engine driven

compressor indoors CAN KILL

YOU IN MINUTES.

Gasoline engine exhaust con-

tains carbon monoxide. This is a

poison you cannot see or smell.

L’utilisation d’un compresseur fonctionnant

avec un moteur à essence à l’intérieur PEUT

VOUS TUER EN QUELQUES MINUTES.

L’échappement d’un moteur à essence

contient du monoxyde de carbone. Il s’agit

d’un poison invisible et inodore.

Usar un compresor con motor a gaso-

lina en interiores PUEDE MATARLO

EN MINUTOS.

El humo de escape del motor a gaso-

lina contiene monóxido de carbono.

Es un veneno que no puede ver u oler.

Only use OUTSIDE and far away from windows, doors and

vents.

N’utiliser qu’à l’EXTÉRIEUR, à l’écart des fenêtres, des

portes et des ouvertures d’aération.

Sólo úselo en EXTERIORES y lejos de las ventanas, puer-

tas y ventilas.

NEVER use inside a home or garage, EVEN IF doors and

windows are open.

NE JAMAIS utiliser à l’intérieur d’une maison ou d’un ga-

rage, MÊME SI les portes et les fenêtres sont ouvertes.

NUNCA lo use dentro de un hogar o cochera, INCLUSO SI

las puertas y ventanas están abiertas. 098-5709-A_7/13/16

WARNING: CONTAINS LEAD. May be harmful if eaten or chewed. May generate dust containing lead. Wash hands after use. Keep out of reach of

children.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or

other reproductive harm. For more information go to www.P65Warnings.ca.gov.

098-6173-A_5/18

AVERTISSEMENT : CONTIENT DU PLOMB. Peut être nocif s'il est ingéré ou mâché. Peut générer de la poussière contenant du plomb. Se laver les mains

après usage. Garder hors de la portée des enfants.

AVERTISSEMENT : Ce produit pourrait vous exposer à des produits chimiques, y compris Plomb, reconnu par l’État de Californie comme cause de

cancer, malformations congénitales ou autres problèmes du système de reproduction. Pour obtenir plus d’information, visitez

www.P65Warnings.ca.gov.

ADVERTENCIA: CONTIENE PLOMO. Puede ser dañino si se ingiere o se mastica. Puede generar polvo que contenga plomo. Lávese las manos después

del uso. Manténgalo fuera del alcance de los niños.

ADVERTENCIA: Este producto le podría exponer a productos químicos incluyendo Plomo, reconocido por el Estado de California como causante de

cáncer, defectos de nacimiento u otros daños del sistema reproductivo. Para obtener más información, visite www.P65Warnings.ca.gov.

19

English

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

Code Certification: Products that bear one or more of the fol-

lowing marks: UL®*, CUL, ETL®*, CETL, have been evaluated by

OSHA certified independent safety laboratories and meet the

applicable Standards for Safety.

* UL® is a registered trademark of Underwriters Laboratories and

ETL® is a registered trademark of Electrical Testing Laboratories.

California Code: Unit may comply with California Code 462 (l) (2)/

(M) (2). Specification/model label is on the side of the air tank on

units that comply with California Code.

Unloader Blow-Off Pressure: All models are continuous running

units controlled by air tank pressure. When the maximum air tank

pressure is obtained, the unloader valve will blow-off. This will

cause the compressor to exhaust the air to the atmosphere and

not the tank. This decreases the load on the engine and allows it

to run at a near no-load condition.

Unloader Reset Pressure: When the air tank pressure drops to

a predetermined point, the unloader valve closes. The air tank

pressure will now increase until it reaches the unloader blow-off

pressure.

20

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or

maintenance personnel can perform some corrective actions, and others may require the assistance of a qualified DeWALT technician or

your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ......................................................................1

Air leaks .................................................................................................................................... 2

Continuous air leak at unloader valve. ......................................................................................3

Air leaks in air tank or at air tank welds ....................................................................................4

Air leaks between head and valve plate ....................................................................................5

Air leaks from safety valve .........................................................................................................6

Compressor is not supplying enough air to operate accessories ............................................2, 7, 8, 9, 10, 12, 13

Restricted air intake. ..................................................................................................................12

Excessive vibration .................................................................................................................... 13

Knocking Noise .........................................................................................................................6, 13

Engine will not run .....................................................................................................................14, 15, 16, 21

Pressure reading on the regulated pressure gauge drops when an accessory is used ........... 17

Regulator knob has continuous air leak ....................................................................................18

Regulator will not shut off air outlet ..........................................................................................18

Pump will not run.......................................................................................................................19

Air tank pressure will not build ..................................................................................................19, 20

La page charge ...

DeWalt DXCMTA5590412 Mode d'emploi

DeWalt DXCMTA5590412 Mode d'emploi

dans d''autres langues