Ryobi Tek4 HP54L Mode d'emploi
- Catégorie
- Outils électroportatifs
- Taper
- Mode d'emploi
Ce manuel convient également à
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
Tek4® SCREWDRIVER
TOURNEVIS Tek4®
DESTORNILLADOR DE Tek4®
HP54L
WARNING: To reduce the
risk of injury, the user must read and
understand the operator’s manual
before using this product.
SAVE THIS MANUAL FOR
FUTURE REFERENCE
ADVERTENCIA: Para reducir
el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
AVERTISSEMENT :
Pour
réduire les risques de blessures,
l’utilisateur doit lire et veiller à bien
comprendre le manuel d’utilisation avant
d’employer ce produit.
GUARDE ESTE MANUAL
PARA FUTURAS CONSULTAS
CONSERVER CE MANUEL
POUR FUTURE RÉFÉRENCE
TABLE OF CONTENTS
****************
General Power Tool
Safety Warnings ..............................2-3
Screwdriver Safety Warnings .............4
Symbols .............................................5
Features .............................................6
Assembly ...........................................6
Operation ........................................6-7
Maintenance ......................................8
Illustrations .........................................9
Parts Ordering
and Service .........................Back page
TABLE DES MATIÈRES
****************
Avertissements de sécurité générales
relatives aux outils électriques ........2-3
Avertissements de sécurité
relatifs tournevis .................................4
Symboles ...........................................5
Caractéristiques ................................. 6
Assemblage .......................................6
Utilisation .......................................6-7
Entretien ............................................. 8
Illustrations .........................................9
Commande de pièces
et dépannage ....................Page arrière
ÍNDICE DE CONTENIDO
****************
Advertencias de seguridad
para herramientas eléctrica ........... 2-3
Advertencias de seguridad
destornillador .....................................4
Símbolos ............................................5
Características ...................................6
Armado ..............................................6
Funcionamiento ............................. 6-7
Mantenimiento ...................................8
Illustraciones ......................................9
Pedidos de piezas
y servicio .......................Pág. posterior
2 — English
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
WORK AREA SAFETY
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body
is earthed or grounded.
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
When operating a power tool outdoors, use an exten-
sion cord suitable for outdoor use. Use of a cord suit-
able for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is un-
avoidable, use a ground fault circuit interrupter (GFCI)
protected supply. Use of a GFCI reduces the risk of
electric shock.
Use battery only with charger listed. For use with 4V
nickel-cadmium and 4V lithium-ion battery packs, see
tool/appliance/battery pack/charger correlation supple-
ment 988000-312.
PERSONAL SAFETY
Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not use
a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inatten-
tion while operating power tools may result in serious
personal injury.
Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal
injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power tool
in unexpected situations.
Dress properly. Do not wear loose clothing or jewel-
lery. Keep your hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or long hair can
be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
power tool in unexpected situations.
POWER TOOL USE AND CARE
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
3 — English
GENERAL POWER TOOL SAFETY WARNINGS
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool
or these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
Maintain power tools. Check for misalignment or bind-
ing of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation.
If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power
tools.
Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
BATTERY TOOL USE AND CARE
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys, nails,
screws or other small metal objects, that can make a
connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
When servicing a power tool, use only identical re-
placement parts. Follow instructions in the Mainte-
nance section of this manual. Use of unauthorized parts
or failure to follow Maintenance instructions may create
a risk of shock or injury.
4 — English
Hold power tool by insulated grippng surfaces, when
performing an operation where the fastener may con-
tact hidden wiring or its own cord. Fasteners contacting
a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well as
the specific potential hazards related to this power
tool. Following this rule will reduce the risk of electric
shock, fire, or serious injury.
Always wear eye protection with side shields marked
to comply with ANSI Z87.1 when assembling parts,
operating the tool, or performing maintenance. Fol-
lowing this rule will reduce the risk of serious personal
injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the risk
of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Battery tools do not have to be plugged into an elec-
trical outlet; therefore, they are always in operating
condition. Be aware of possible hazards when not
using your battery tool or when changing accessories.
Following this rule will reduce the risk of electric shock,
fire, or serious personal injury.
Do not place battery tools or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped
or received a sharp blow. A damaged battery is subject
to explosion. Properly dispose of a dropped or damaged
battery immediately.
Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
For best results, your battery tool should be charged
in a location where the temperature is more than 50°F
but less than 100°F. To reduce the risk of serious personal
injury, do not store outside or in vehicles.
Under extreme usage or temperature conditions, bat-
tery leakage may occur. If liquid comes in contact with
your skin, wash immediately with soap and water. If
liquid gets into your eyes, flush them with clean water
for at least 10 minutes, then seek immediate medical
attention. Following this rule will reduce the risk of seri-
ous personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also.
SCREWDRIVER SAFETY WARNINGS
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities may
contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products and,
• arsenic and chromium from chemically treated lumber.
Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To reduce your
exposure, work in a well-ventilated area and with approved safety equipment, such as dust masks that are specially
designed to filter out microscopic particles.
CALIFORNIA PROPOSITION 65
5 — English
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal injury hazard.
Read Operator’s
Manual
To reduce the risk of injury, user must read and understand operator’s manual
before using this product.
Eye Protection
Always wear eye protection with side shields marked to comply with ANSI
Z87.1.
Wet Conditions
Alert
Do not expose to rain or use in damp locations.
Recycle Symbol
This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws
may prohibit disposal of batteries in ordinary trash. Consult your local waste
authority for information regarding available recycling and/or disposal options.
V Volts Voltage
min Minutes Time
Direct Current Type or a characteristic of current
n
o
No Load Speed Rotational speed, at no load
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING:
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION:
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
NOTICE:
(Without Safety Alert Symbol) Indicates important information not related to an
injury hazard, such as a situation that may result in property damage.
6 — English
FEATURES
PRODUCT SPECIFICATIONS
No Load Speed .....................................................................................................................................200/600 r/min. (RPM)
Torque ........................................................................................................................................................................40 in. lb.
Collet .............................................................................................................................................................................1/4 in.
ASSEMBLY
WARNING:
Do not use this product if it is not completely assembled
or if any parts appear to be missing or damaged. Use of
a product that is not properly and completely assembled
or with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create acces-
sories or attachments not recommended for use with this
product. Any such alteration or modification is misuse
and could result in a hazardous condition leading to
possible serious personal injury.
If any parts are damaged or missing, please call 1-800-525-2579 for assistance. In Mexico, please call 01-800-843-1111.
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict serious injury.
WARNING:
Always remove battery pack from the tool when you are
assembling parts, making adjustments, cleaning, or when
not in use. Removing battery pack will prevent accidental
starting that could cause serious personal injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing protection.
Failure to do so could result in objects being thrown into
your eyes and other possible serious injuries.
OPERATION
WARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Driving screws with screwdriver bits
Light-duty drilling
7 — English
TWO-SPEED GEAR TRAIN
See Figure 3, page 9.
The screwdriver has a two-speed gear train designed for low
(Position 1) or high (Position 2) speeds. A slide switch is
located on top of the screwdriver to select the speed setting.
When using screwdriver in the low speed range (Position 1),
speed will decrease and unit will have more power. When
using screwdriver in the high speed range (Position 2),
speed will increase and unit will have less power. Use the
high speed setting to drill holes and the low speed setting
for driving screws.
When drilling use 1/4 in. hex shank drill bits only. Maximum
bit size is 1/4 in.
WARNING:
Battery tools are always in operating condition. Lock the
switch when not in use or carrying at your side, when
installing or removing the battery pack, and when install-
ing or removing bits.
TO LOAD/RELEASE BITS
See Figure 4, page 9.
Insert the bit into the collet and push the bit in as far as pos-
sible. To remove a bit, pull the bit straight out of the collet.
NOTE: For ease of removal, the use of 2 in. bits is
recommended.
ADJUSTABLE TORQUE CLUTCH
This screwdriver is equipped with an adjustable torque clutch
for driving different types of screws into different materials.
The proper setting depends on the type of material and the
size of screw you are using.
LED WORKLIGHT
See Figure 5, page 9.
The built-in LED worklight is convenient when working in close
or tight areas where additional light is needed. Whenever the
switch trigger is depressed, the LED worklight will illuminate.
OPERATION
INSTALLING/REMOVING BATTERY PACK
See Figure 1, page 9.
To install the battery pack:
Unscrew the battery cap.
Insert the battery pack in the direction shown. Make sure
the raised rib on the battery pack aligns with the groove
in the compartment.
Place the cap over the battery pack and push down
until the cap meets the threads at the end of the battery
compartment.
Screw the cap on securely.
NOTE: To prevent accidental discharge of the battery pack,
the screwdriver has an automatic shutoff feature that acti-
vates after 2 minutes of continuous use. To restart, release
the switch trigger, then again.
To remove the battery pack:
Unscrew the cap. The battery pack will disconnect and
be easy to remove.
Do not attempt to use this product if the battery cap is
not securely closed.
For complete charging instructions, see the operator’s manu-
als for your battery pack and charger.
DIRECTION OF ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK)
See Figure 2, page 9.
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
screwdriver held in normal operating position, the direction
of rotation selector should be positioned to the left of the
switch trigger for forward motion. The direction is reversed
when the selector is to the right of the switch trigger.
Setting the direction of rotation selector in the OFF (center
lock) position helps reduce the possibility of accidental start-
ing when not in use.
NOTICE:
To prevent gear damage, always allow the collet to
come to a complete stop before changing the direction
of rotation.
To stop the screwdriver, release the switch trigger and allow
the collet to come to a complete stop.
NOTE: The screwdriver will not run unless the direction of
rotation selector is pushed fully to the left or right.
8 — English
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts could create a hazard or cause
product damage.
MAINTENANCE
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
NOTE: ILLUSTRATIONS START ON PAGE 9 AFTER
FRENCH AND SPANISH LANGUAGE SECTIONS.
9
HP54L
A - LED worklight (lampes à del, luz de
trabajo de diodo luminiscente)
B - Collet (collet, portaherramientas)
C - Two-speed gear train (high-low) [train
d’engrenages à deux vitesses (haute et
basse), engranaje de dos velocidades (alta-
baja)]
D - Direction of rotation selector (forward/
reverse/center lock) [sélecteur de sens
de rotation (avant/arrière/verrouillage
central), selector de sentido de rotación
(adelante / atrás / seguro en el centro)]
F - Switch trigger (commutateur, interruptor)
E - Battery cap (couvercle de pile; cubierta de
batería)
F
D
C
E
A
B
C
A
B
A - Bit (embout, broca)
B - Collet (collet, portaherramientas)
A
Fig. 4
B
Fig. 3
A - Reverse (arrière, adalante)
B - Forward (avant, atras)
A - High speed (position 2) [(vitesse élevée
(position 2), velocidad alta (posición 2)]
B - Low speed (position 1) [(vitesse faible
(position 1), velocidad low (baja)
(posición 1)]
C - Two-speed gear train (high-low) (train
d’engrenages à deux vitesses [haute et basse],
engranaje de dos velocidades [altabaja])
Fig. 2
A
B
Fig. 1
Fig. 5
A - Groove (rainure, ranura)
B - Battery pack (bloc-pile, paquete de baterías)
C - Raised ribs (épaulements surélevés,
costillas realzadas)
D - Battery cap (couvercle de pile; cubierta de
batería)
B
D
C
A
ALIGN RAISED RIBS
WITH GROOVE IN HANDLE
ALIGNER LES TASSEAUX AVEC LA RAINURE DANS
LA BASE DE LA LAMPE DE TORCHE
ALINEE LAS COSTILLAS REALZADAS CON LA
RANURA QUE SE ENCUENTRA DENTRO DE LA BASE
DE LA LINTERNA
A
A - LED worklight (lampes à del, luz de trabajo
de diodo luminiscente)
991000172
8-29-14 (REV:01)
OPERATOR’S MANUAL / Tek4® SCREWDRIVER
MANUEL D’UTILISATION / TOURNEVIS Tek4®
MANUAL DEL OPERADOR / DESTORNILLADOR DE Tek4®
HP54L
RYOBI is a registered trademark of Ryobi Limited and is used pursuant to a license granted by Ryobi Limited.
RYOBI est une marque déposée de Ryobi Limited et est utilisée en vertu d’une licence accordée par Ryobi Limited.
To request service, purchase replacement parts,
locate an Authorized Service Center and obtain Customer or Technical Support:
Visit www.ryobitools.com or call 1-800-525-2579
If any parts or accessories are damaged or missing,
do not return this product to the store. Call 1-800-525-2579 for immediate service.
Please obtain your model and serial number from the product data plate.
This product is covered under a 3-year limited Warranty. Proof of purchase is required.
MODEL NUMBER _______________ SERIAL NUMBER ____________________________
Pour faire une demande de réparations ou obtenir des pièces de rechange, trouver un
Centre de réparations agréé pour obtenir un soutien technique ou le Service à la clientèle :
Visiter www.ryobitools.com ou en téléphonant au 1-800-525-2579
Si des pièces ou accessoires sont manquantes ou endommagées, ne pas retourner
ce produit au magasin. Appeler immédiatement au 1-800-525-2579 pour obtenir de l’aide.
Inscrire les numéros de modèle et de série inscrits sur la plaque d’identification du produit.
Ce produit est couvert par une garantie limitée de trois (3) ans. Une preuve d’achat est exigée.
NUMÉRO DE MODÈLE _______________ NUMÉRO DE SÉRIE ____________________________
RYOBI es una marca registrada de Ryobi Limited y se utiliza conforme a una licencia otorgada por Ryobi Limited.
Para obtener servicio, comprar piezas de repuesto, localizar un centro de servicio autorizado
y obtener Servicio o Asistencia Técnica al Consumidor:
Visite www.ryobitools.com (en la EE.UU.) o www.ryobitools.mx (en México)
o llame al 1-800-525-2579 (en la EE.UU.) o 01-800-843-1111 (en México).
Si hay alguna pieza o accesorios dañada o faltante, no devuelva este producto a la tienda.
Llame al 1-800-525-2579 (en la EE.UU.) o 01-800-843-1111 (en México) para servicio técnico inmediato.
Obtenga su modelo y número de serie de la placa de datos del producto.
Este producto está cubierto con una garantía limitada de 3 años. Se solicita prueba de la compra.
NÚMERO DE MODELO _______________ NÚMERO DE SERIE ____________________________
ONE WORLD TECHNOLOGIES, INC.
1428 Pearman Dairy Road, Anderson, SC 29625 • Phone 1-800-525-2579
États-Unis, Téléphone 1-800-525-2579 • USA, Teléfono 1-800-525-2579
www.ryobitools.com
A subsidiary of Techtronic Industries Co., LTD OTC: TTNDY
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ryobi Tek4 HP54L Mode d'emploi
- Catégorie
- Outils électroportatifs
- Taper
- Mode d'emploi
- Ce manuel convient également à
dans d''autres langues
- English: Ryobi Tek4 HP54L User guide
Documents connexes
-
Ryobi P340 Mode d'emploi
-
-
-
-
-
-
-
-
Ryobi HP74L Le manuel du propriétaire
-