MTD OHD-190-182 Manuel utilisateur

Taper
Manuel utilisateur
To The Owner • Carton Contents • Assembly • Parts Lists • Warranty
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
IMPORTANT
OPERATOR’S MANUAL
Model OHD-190-182
Twin Rear Bagger Kit
For Lawn Tractors & Garden Tractors
with a 46” Deck
01/04/2006
FORM NO. 769-02303
2
Finding and Recording Model Number
Model Number Serial Number
BEFORE YOU START ASSEMBLING YOUR NEW EQUIPMENT,
please locate the model plate and copy the information from it in this Operator’s Manual for future reference. The information on
the model plate is very important if you need help from our Customer Support Department or your authorized dealer.
You can locate it by looking on the front, left portion of the plastic grass catcher cover as seen below:
This Operators Manual is an important part of your new grass collector. It will help you assemble,
prepare and maintain the unit for best performance. Please read and understand what it says.
Please do
NOT
return the unit to the retailer from which it was
purchased, without first contacting Customer Support.
Customer Support
If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of this
unit, you can seek help from the experts. Choose from the options below:
Visit mtdproducts.com. Click on the Service & Support menu option.
Phone a Customer Support Representative at 1-800-800-7310.
Please have your unit’s model number and serial number ready when you call. See previous section to locate this information.
You will be asked to enter the serial number in order to process your call.
*Locate the model plate on your bagger and copy the information from it in the space provided above for future reference.
3
1
Rider Model
Identification
FastAttach
Twin Bag
Grass Collector
The Model OEM-190-182 Twin Bag Grass Collector is a
grass collection system designed for use on all MTD 46”
cut FastAttach™ compatible lawn tractors (except 2001
MTD/Yard-Man Revolution).
The instructions in this manual are divided into sections.
Carefully read all sections and study the illustrations to
ensure proper installation and usage of this attachment.
Read and observe all WARNING and CAUTION state-
ments. They are included to provide for the protection
of the equipment installer and user, and to ensure the
prolonged service life of the equipment.
NOTE: References to LEFT and RIGHT indicate the left
and right sides of the tractor when facing forward in the
operators position. Reference to the FRONT indicates
the grille end; to the REAR, the rear end of the tractor.
Determine The Model
of Your Rider
Since this manual is designed for installation of your new
bagger on several different rider units, it is important
for you to determine which model of rider you have.
Therefore you will know which set of instructions in the
following pages to follow.
To determine which model of rider you have, you will
need to locate the rider’s model plate, located under the
seat. Simply flip the seat up and locate the model plate,
which will consist of an 11 digit/letter model number
and a serial number. For ease in this installation and
for future use, copy your rider’s model number & serial
number below now:
Rider Model Number:__ __ __ __ __ __ __ __ __ __ __
Rider Serial Number:_________________________
The 5
th
, 6
th
& 7
th
numbers from the left in your model
number determine your riders model series. See Figure
2.
When you fill in your model number in the space above,
the actual model series number should fall into the gray
shaded area.
Now that you have determined what model rider you are
attaching this grass bag collection system to, follow the
instructions on the following pages according to your
model of rider.
NOTE: References to
LEFT and RIGHT indicate
the left and right sides of
the tractor when facing
forward in the operators
position. Reference to the
FRONT indicates the grille
end; to the REAR, the reare
end of the tractor.
Figure 1
Figure 2
w
w
w
.
m
t
d
p
r
o
d
u
c
t
s
.
c
o
m
M
T
D
L
L
C
P
.
O
.
B
O
X
3
6
1
1
3
1
C
L
E
V
E
L
A
N
D
,
O
H
4
4
13
6
3
3
0
-
2
2
0
-
4
6
8
3
8
0
0
-
8
0
0
-
7
3
1
0
Model Plate
1 3 A M 6 1 9 G 0 0 0
Indicates Model Series 600
Sample Model Number
4
CONTENTS OF CARTON
Before beginning installation, remove all parts from the carton to make sure everything is present. Carton
contents are listed below and shown in Figure 1. Hardware part numbers are shown in parentheses.
One Chute Tube
One Discharge Chute Assembly
Two Grass Bag Assemblies
One Support Tube
One Grass Catcher Cover Assembly
One Mounting Bracket
Three Blades
2
Carton
Contents
If you are missing
any parts, please
do not contact the
retailer where you
purchased this unit,
call MTD directly at
1-330-220-4MTD or
toll free at
1-800-800-7310.
Figure 3
5
2
If you are missing
any parts, please
do not contact the
retailer where you
purchased this unit,
call MTD directly at
1-330-220-4MTD or
toll free at
1-800-800-7310.
NOTE:
Each item
has been identified
in above for ease of
assembly, and the
letter code assigned
here is maintained
in assembly instruc-
tions.
RH = Right Hand
LH = Left Hand
CONTENTS OF HARDWARE PACK
This grass collector kit is shipped with a hardware pack enclosed. This hardware pack may contain extra
parts for installation on a different rider from which you have. Please check your hardware pack against the
illustration below in accordance with your model of rider as determined in Section 1 of this manual.
For decks with grass catcher pin
not pre-installed
Carton
Contents
NOTE: Each item has been identified in above for ease of assembly, and the letter code assigned here is maintained
in assembly instructions.
RH = Right Hand (#) = Quantity
LH = Left Hand
For older tractors only
D
F3
F2 F1
(LH) (RH)
A
B
C
E
H
G
(1)
(1)
(1)
(1)(1)
(2)
(2)
(4)
(2)
(2)
Figure 4
For all model series 820 through 849 tractors
For all model series 650 through 699 tractors
A
B
C
(2)
(2)
(2)
6
3
Attaching
Bracket
Assembly
Model Series 600
through 619
IMPORTANT:
Before assembly, place
the tractor on a firm,
level surface, disengage
the PTO, stop the tractor
engine and set the park-
ing brake.
NOTE:
There are two holes in
the clevis pin. Be sure
to insert the hairpin
clip in the upper hole
to properly secure the
bracket assembly to the
hitch plate.
Attaching The Bracket
Assembly
Model Series 600 through 619
Model Series 800 through 819
IMPORTANT: Before assembly, place the tractor on
a firm, level surface, disengage the PTO, stop the
tractor engine and set the parking brake.
1. For convenience, pivot the seat forward and leave
it in that position until the grass collector is fully
mounted and assembled.
2. Remove the hairpin clip and clevis pin from the rear
of the mounting bracket assembly. See Figure 5.
3. Position the hooked ends of the bracket assembly
over the shoulder bolts (1). Swing in the bottom of
the bracket assembly down and in (2) over the hitch
plate and aligning with the hole on the hitch plate.
See Figure 5.
4. Reinsert the clevis pin through the aligned holes in
both the bracket assembly and the hitch plate and
secure with the hairpin clip removed earlier. Refer to
Figure 6.
NOTE: There are two holes in the clevis pin. Be
sure to insert the hairpin clip in the upper hole to
properly secure the bracket assembly to the hitch
plate.
Figure 5
Figure 6
Figure 7
Figure 8
Upper Hole
Hitch Plate
Outside of Bracket
Outer Hole
Model Series 650 through 699
This graphic below coordinates with the instructions for the Model Series 650 through 699, which begin on the next page.
Support
Bracket
Screws
Removed
Earlier
Remove
Pin
7
Figure 10
Figure 9
3
Attaching
Support
Bracket &
Bracket
Assembly
Model Series 650
through 699
IMPORTANT:
Before assembly, place
the tractor on a firm,
level surface, disengage
the PTO, turn off tractor
engine and set the park-
ing brake.
NOTE:
If the grass collection
system is removed for
any reason, it is not
necessary to remove the
support brackets from the
tractor.
IMPORTANT:
There are two holes in
the clevis pin. Be sure
to insert the hairpin
clip in the upper hole
to properly secure the
bracket assembly to the
hitch plate.
NOTE:
For some tractor
models, this clevis
pin is too large. Use a
smaller clevis pin in
its place with the same
hairpin clip.
Assembling Support
Brackets
Model Series 650 through 699
IMPORTANT: Before assembly, place the tractor on
a firm, level surface, disengage the PTO, stop the
tractor engine and set the parking brake.
1. Remove the top four self-tapping screws from the rear
of the lawn tractor. See Figure 7 on the previous page.
2. Place the right hand grass catcher support bracket (F1
from Figure 4), in position, with the wide end on top and
the narrow end pointing down as shown in Figure 8.
3. Secure the support bracket to the tractor frame with two
self-tapping screws earlier removed. Refer to Figure 8.
Repeat on the other side using part F2 from Figure 4.
NOTE: If the grass collection system is removed for
any reason, it is not necessary to remove the support
brackets from the tractor.
4. Insert a shoulder bolt (C in Figure 4) through a bell
washer, (B in Figure 4) and insert the bolt from the
outside of the bracket through the outer hole on the
support bracket. Secure with a nut (A in Figure 4).
See Figure 8 for details. Repeat on other side.
NOTE: The reference above to “the outer hole”
means the hole furthest away from the frame.
Attaching Bracket
Assembly
Model Series 650 through 699
1. Remove the two nuts and bolts on each side of the
mounting bracket holding the hitch plate.
2. Rotate the hitch plate 180° from its original position.
Re-insert the four bolts through mounting bracket
and hitch plate frame and secure with nuts removed
earlier. Use the outer holes (furthest from the mount
-
ing hooks) on the mounting bracket. See Figure 10.
3. For convenience, pivot the seat forward and leave it in
that position until the grass collector is fully mounted
and assembled.
4. Remove the hairpin clip and clevis pin from the rear of
the mounting bracket assembly. See Figure 9.
5. Position the hooked ends of the mounting bracket
assembly to the outside of the support brackets and
over the shoulder bolts just installed on both sides of
the tractor frame. See Figure 11.
6. Reinsert the clevis pin through the aligned holes in
both the bracket assembly and the hitch plate and
secure with the hairpin clip removed earlier. See
Figure 12 for reference.
IMPORTANT: There are two holes in the clevis pin.
Be sure to insert the hairpin clip in the upper hole to
properly secure the bracket assembly to the hitch plate.
NOTE: For some tractor models, this clevis pin is
too large. Use a smaller clevis pin (E in Figure 4) in
its place with the same hairpin clip.
Outer holes
Figure 11
Figure 12
Upper Hole
Clevis Pin
8
3
Attaching
Support
Bracket &
Bracket
Assembly
Model Series 820
through 849
NOTE:
If the grass collection
system is removed for
any reason, it is not
necessary to remove the
support brackets from the
tractor.
IMPORTANT:
There are two holes in
the clevis pin. Be sure
to insert the hairpin
clip in the upper hole
to properly secure the
bracket assembly to the
hitch plate.
Assembling Support
Brackets
Model Series 820 through 849
1. Locate the four self-tapping screws supplied in your
hardware pack (D from Figure 4). Attach one of
the grass catcher support brackets (F3 from Figure
4) using two of the supplied screws in position as
shown in Figure 13. Place the other grass catcher
support bracket (F3 from Figure 4) in position and
secure with the other two screws.
5. Insert a shoulder bolt (C in Figure 4) through a bell
washer, (B in Figure 4) and insert the bolt through
the remaining hole from the outside of the support
bracket. Secure with a nut (A in Figure 4). See Figure
13 for details. Repeat on other side.
NOTE: If the grass collection system is removed
for any reason, it is not necessary to remove the
support brackets from the tractor.
Attaching The Bracket
Assembly
1. Remove the two nuts and screws on each side of the
mounting bracket holding the hitch plate.
See Figure 14.
2. Rotate the hitch plate 180° from its original position.
Re-insert the four bolts through mounting bracket
and hitch plate frame and secure with nuts removed
earlier. Use the inner holes (closest to the mounting
hooks) on the mounting bracket. Refer to Figure 15.
3. Remove the hairpin clip and clevis pin from the hitch
plate as seen in Figure 14. Save the hardware.
4. Position the hooked ends of the mounting bracket
assembly to the outside of the support bracket and
over the shoulder bolts on both sides. Refer back to
Figure 11 for reference.
5. Reinsert the clevis pin through the aligned holes in
both the bracket assembly and the hitch plate and
secure with the hairpin clip removed earlier. See
Figure 16.
IMPORTANT: There are two holes in the clevis pin.
Be sure to insert the hairpin clip in the upper hole to
properly secure the bracket assembly to the hitch
plate.
Figure 13
Figure 15
Figure 16
Figure 14
Inner holes
Upper Hole
Clevis Pin
9
Attaching Grass Bags &
Grass Bag Cover
1. Place the support tube in position on the rear of unit
by sliding the support tube down through the holes in
the left side of the bracket assembly. Use the inside
hole on the bracket assembly regardless of what size
deck your tractor is equipped with. Refer to Figure 17.
2. Attach the grass bags by hooking them onto the grass
bag bracket using the slots in the grass bag and the
tabs on the grass bag bracket as shown in Figure 18.
3. Place the grass bag cover on top of the grass bags
and align the holes on the hinges of the grass bag
cover with the corresponding holes on the support
tube assembly. See Figure 19.
4. Insert the clevis pin through the hinge on the support
tube assembly and then through the grass bag cover.
See Figure 20.
5. Secure with belleville washer and hairpin clip with the
crown side of the washer going against the hairpin
clip. See inset images in Figure 20.
6. Repeat with the second set of hardware through the
second hinge of the grass bag and the tube assembly
from the opposite direction.
NOTE: Insert the clevis pins from the outside in as
shown in the inset images of Figure 20.
NOTE: It is very important to maintain this order
and direction while installing these hardware pieces.
After installation, make sure that the grass bag cover
pivots on the support tube and opens.
4
NOTE:
Insert the clevis pins
from the outside in as
shown in the inset
images of Figure 20.
NOTE:
It is very important to
maintain this order and
direction while installing
these hardware pieces.
After installation, make
sure that the grass bag
cover pivots on the sup-
port tube and opens.
Attaching
Grass Bags
& Grass Bag
Cover
All Model Series
600 through 800
Figure 18
Figure 19
Figure 20
Figure 17
10
Attaching The Blades
Remove the blades from your tractor’s cutting deck as
follows:
1. Remove the cutting deck from beneath the tractor,
(refer to Deck Removal in the MAINTENANCE sec-
tion of your tractor’s operator’s manual for detailed
instructions) then gently flip the deck over to expose
its underside.
2. Place a block of wood between the center deck
housing baffle and the cutting blade to act as a
stabilizer, keeping the blades from turning when you
loosen the hex flange nuts.
3. Use a 15/16” wrench to remove the hex flange nut
that secures the blade to the spindle assembly.
NOTE: The hex flange nut has a normal (right-handed)
thread pattern. Do NOT attempt to force the nut in the
incorrect direction. Doing so may damage the nut and
create a safety hazard.
4. Install the new blades packed with the bagger. Be
sure to install the blade with the side of the blade
marked ‘‘Bottom’’ (or with a part number stamped
in it) facing the ground when the rider is in the
operating position.
5. Mount the SMALLER of the three blades to the
CENTER spindle. The remaining two blades are
interchangeable. See Figure 21.
6. Use a torque wrench to tighten the blade spindle hex
flange nut to between 70 and 90 foot-pounds.
7. Remount the cutting deck.
Attaching Discharge Chute
1. On older models: Some older models may have a
clip already installed on the deck (See Figure 22) next
to the discharge chute opening. If this is the case, the
clip must be removed and a grass catcher pin, which is
inlcuded in your hardware pack, installed. To remove
clip, simply remove the lock nut, spring washer and hex
bolt that secure it. See Figure 23A.
2. Installing Grass Catcher Pin: A grass catcher pin
(G in Figure 4) and nut (H in Figure 4) have been
supplied in the hardware pack. Attach pin to the
deck in place of the clip just removed. Some units
may not have clip but will have an open hole for pin
installation. Follow Figure 23B for order of assem-
bly. Make sure to secure the pin tightly.
NOTE: The retainer strap is fitted at position A on the
discharge chute. However, on older models of trac-
tors, you will have to change the position of the strap
depending on the location of the grass catcher pin on
the deck. Remove the retainer strap from position A on
the discharge chute to position B or C corresponding to
the position of the grass catcher pin at A, B or C on the
deck. See Figure 24.
Figure 24
Figure 23
5
Attaching
Discharge
Chute
All 600 Model Series
600 through 699
NOTE:
The hex flange nut has
a normal (right-handed)
thread pattern. Do NOT
attempt to force the nut
in the incorrect direction.
Doing so may damage the
nut and create a safety
hazard.
NOTE:
The retainer strap is
fitted at position B on
the discharge chute.
However, on older models
of tractors, you will have
to change the position of
the strap depending on
the location of the grass
catcher pin on the deck.
Remove the retainer strap
from position B on the
discharge chute to posi-
tion A or C corresponding
to the position of the
grass catcher pin at A,
B or C on the deck. See
Figure 24.
Figure 21
Figure 22
A
B
Smaller Blade
Part No. 742-0645
Larger Blades
Part No. 742-0644
Hex Flange Nut
11
Figure 25
Figure 27
NOTE:
When both grass bags
are full, place the tractor
on a firm, level surface,
disengage the PTO, turn
the tractor engine off and
set the parking brake.
5
Attaching
Discharge
Chute
All Model Series
Grass Catcher Pin
Retainer Strap
Tab
Pocket
Figure 26
3. Raise the deck to its highest position.
4. Raise the chute deflector on the deck and hold it
while you position the discharge chute over the
chute opening. See Figure 25.
5. Place the top rear edge of the discharge chute over
the top rear edge of the chute opening.
6. Push down on the discharge chute so that its front
bottom edge rolls around the bottom of the deck,
then slide the chute forward to the stop on the deck.
7. Lock the discharge chute in position by hooking
the retainer strap over the grass catcher pin on the
deck. See Figure 25.
8. Insert the curved end of chute tube into the hole in
the grass bag cover. See Figure 26.
9. Place the lower end of the chute tube over the
discharge chute so that the tabs on the discharge
chute fits into the pockets on the chute tube. See
Figure 27.
10. Secure by hooking the two retainer straps of the
discharge chute to the pins on the chute tube. See
Figure 27.
Bagger Usage
NOTE: When both grass bags are full, place the tractor
on a firm, level surface, disengage the PTO, turn the
tractor engine off and set the parking brake.
1. Flip Seat up.
2. Lift up grass bag cover. Do not remove the chute
tube assembly from the tractor.
3. Remove the grass bags by lifting these up and mov-
ing the bags away from the support tube assembly.
4. Empty the grass clippings at a proper disposal sight,
use the handle at the bottom of each grass bag.
Holding the bag firmly, empty the contents
5. Replace grass bags, close lid, flip down seat, restart
your tractor and resume cutting your grass.
12
1
2
35
37
10
11
5
25
26
33
33
27
9
9
28
3
18
12
7
10
20
14
13
32
10
34
34
34
21
21
8
19
6
10
20
20
10
13
13
32
15
22
23
24
29
30
31
31
30
38
29
16
4
11
11
39
36
6
For parts and/or
accessories
please call
1-800-800-7310, or
1-330-220-4683.
www.mtdproducts.com
Part List:
Rear Twin
Bagger
13
6
REF
NO.
PART NUMBER DESCRIPTION Qty.
1 16587D Support Bracket: Bagger 2
2 16592 Support Tube Assembly 1
3 664-04017 Grass catcher Cover Assembly 1
4 710-0597 Screw 1/4-20 x 1” 3
5 711-0309A Clevis Pin 1
6 711-0310 Clevis Pin (on older model tractors) 1
7 711-1421 Clevis Pin 2
8 712-0459 Lock Nut 7/16-20 2
9 712-3004A Lock Nut 5/16-18 6
10 712-3027 Hex Flange Lock Nut, 1/4-20 14
11 714-0117 Hairpin Clip 1
12 714-0145 Click Pin
2
13 723-04008A Chute Strap
3
14 731-04159 Discharge Chute 46
1
15 731-0926B Catcher Tube
1
16 710-0604A Self-Tapping Screw 5/16-18
8
17 16591A Bag Hanger Bracket
2
18 736-0331 Bell Washer
2
19 736-0407 Bell Washer
2
20 736-3092 Flat Washer
3
21 738-1020 Shoulder Screw
2
22 783-04132A Support Bracket (RH)
1
23 783-04137A Support Bracket (LH)
1
24 783-0601 Mounting Bracket
1
25 783-0673A Catcher Support Bracket (RH)
1
26 783-0764A Catcher Support Bracket (LH)
1
27 783-0765 Bracket: Cross Support
1
28 764-0221 Catcher Bag
2
29 749-0701A Grass Bag Frame
2
30 712-0272 Hex Sems Nut, #10-24 10
31 710-0473 Machine Screw, , #10-24 x .5 10
32 710-0726 AB Screw 5/16-12
4
33 710-3008 Hex Screw 5/16-18 x 0.75”
6
34 711-04069 Grass catcher Pin
3
35 710-0751 Hex Screw 1/4-20 x0.620
8
36 710-0623 Self-tapping Screw 3/8-16 x 0.75”
4
37 742-0644 Blade 16.28” Lg.
2
38 742-0645 Blade 14.88” Lg.
1
39 783-04138 Support Bracket
2
40 710-0597 Hex Head Screw 1/4-20 x 1
3
For parts and/or
accessories
please call
1-800-800-7310, or
1-330-220-4683.
www.mtdproducts.com
Part List:
Rear Twin
Bagger
The limited warranty set forth below is given by MTD LLC with respect
to new merchandise purchased and used in the United States, its
possessions and territories.
MTD” warrants this product against defects in material and workman-
ship for a period of two (2) years commencing on the date of original
purchase and will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited war-
ranty shall only apply if this product has been operated and maintained
in accordance with the Operator’s Manual furnished with the product,
and has not been subject to misuse, abuse, commercial use, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire, water,
or damage because of other peril or natural disaster. Damage resulting
from the installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this manual
will void your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batter-
ies, belts, blades, blade adapters, grass bags, rider deck wheels, seats,
snow thrower skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area, check your Yellow Pages,
or contact MTD LLC at P.O. Box 361131, Cleveland, Ohio 44136-
0019, or call 1-800-800-7310 or 1-330-220-4683 or log on to our
Web site at www.mtdproducts.com.
This limited warranty does not provide coverage in the following cases:
a. The engine or component parts thereof. These items may carry a
separate manufacturer’s warranty. Refer to applicable manufacturer’s
warranty for terms and conditions.
b. Log splitter pumps, valves, and cylinders have a separate one year
warranty.
c. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments, deck
adjustments, and normal deterioration of the exterior finish due to
use or exposure.
d. Service completed by someone other than an authorized service
dealer.
e. MTD does not extend any warranty for products sold or exported
outside of the United States, its possessions and territories, except
those sold through MTD’s authorized channels of export distribution.
f. Replacement parts that are not genuine MTD parts.
g. Transportation charges and service calls.
No implied warranty, including any implied warranty of mer-
chantability of fitness for a particular purpose, applies after the
applicable period of express written warranty above as to the
parts as identified. No other express warranty, whether written or
oral, except as mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product, shall
bind MTD. During the period of the warranty, the exclusive remedy
is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. MTD shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn
care services or for rental expenses to temporarily replace a
warranted product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of
the product shall void this warranty. You assume the risk and liability
for loss, damage, or injury to you and your property and/or to others and
their property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
MANUFACTURER’S LIMITED WARRANTY FOR
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683
Al propietario • Contenido de la caja • Ensamblado • Listados de piezas • Garantía
MTD LLC. APARTADO POSTAL 361131 CLEVELAND, OHIO 44136-0019
IMPRESO EN
ESTADOS UNIDOS
DE AMÉRICA
LEA CON ATENCIÓN LAS REGLAS DE SEGURIDAD E INSTRUCCIONES ANTES DE OPERAR
LA UNIDAD
IMPORTANTE
MANUAL DEL OPERADOR
Modelo OHD-190-182
Kit de embolsado posterior doble
Para tractores cortacésped y tractores de jardín con
plataforma de 46”
12/15/2005
FORMULARIO Nº . 769-02303
2
Búsqueda y registro del número de modelo
ANTES DE COMENZAR A MONTAR SU NUEVO EQUIPO,
por favor ubique la placa de modelo y copie la información de la misma en el Manual de Operador para referencia futura. La
información contenida en la placa del modelo es muy importante en caso de necesitar ayuda de nuestro Departamento de
Asistencia al Cliente o del distribuidor autorizado.
Puede ubicar la misma mirando en la parte delantera, lado izquierdo, de la cubierta de la tolva plástica para recorte de césped,
según se muestra a continuación:
Este Manual del Operador es una parte importante de su nuevo colector de césped. Le ayudará a
montar, preparar y mantener la unidad para obtener los mejores resultados. Por favor, lea y com-
prenda el contenido del manual.
Por favor, NO devuelva la unidad al minorista a quien se la adquirió sin ponerse en contacto
primero con el Departamento de Asistencia al Cliente.
Asistencia al cliente
En caso de tener problemas para montar este producto o de tener dudas con respecto a los controles, funcionamiento o
mantenimiento del mismo, puede solicitar la ayuda de expertos. Elija entre las opciones que se presentan a continuación:
• Visite mtdproducts.com. Haga clic en la opción Service & Support (Servicio y Asistencia) del menú.
Comuníquese por teléfono con un Representante de Asistencia al Cliente al 1-800 -800-7310.
Por favor tenga a mano el número de modelo y el número de serie de su unidad cuando llame. Consulte la sección anterior
para obtener esta información. Se le solicitará que ingrese el número de serie para poder procesar su llamada.
*Ubique la placa de modelo en su embolsadora y copie la información de la misma en el espacio provisto más arriba para referencia futura
Número de modelo Número de serie
3
1
1
Identificación
del modelo
de podadora
tractor
Colector de césped
FastAttach™ con
sistema de bolsa doble
TEl colector de césped con bolsa doble modelo OEM-
190-182 es un sistema de recogida de césped diseñado
para ser usado en todos los tractores cortacésped MTD
compatibles con plataformas de 46” (excepto 2001 MTD
Yard-Man Revolution).
Las instrucciones de este manual se dividen en sec-
ciones. Lea con atención todas las secciones y estudie
las ilustraciones para asegurar una adecuada instalación
y uso de este aditamento. Lea y observe todas las
declaraciones de ADVERTENCIA y PRECAUCIÓN. Se
las ha incluido para proporcionar protección al instalador
y al usuario del equipo, y para asegurar una prolongada
vida de servicio del equipamiento.
NOTA: Las referencias relativas a los lados IZQUIERDO
y DERECHO indican los lados izquierdo y derecho del
tractor mirando hacia adelante desde la posición del
operador. La referencia al FRENTE indica el extremo
de la parrilla; la referencia al lado POSTERIOR indica el
extremo trasero del tractor.
Determine el modelo
de la podadora tractor
Como este manual ha sido diseñado para la instalación
de la nueva embolsadora en diversas unidades de
podadora tractor, es importante que determine cuál es
el modelo de podadora tractor que usted posee. De
ese modo usted sabrá cuál es el grupo de las siguientes
instrucciones que deberá observar.
Para determinar cuál es el modelo de podadora tractor
que usted posee, será necesario que ubique la placa de
modelo de la podadora tractor que se encuentra debajo
del asiento. Simplemente levante el asiento y ubique
la placa de modelo, la cual comprende un número de
modelo de 11 dígitos/ letras y un número de serie. Para
facilitar la instalación y para uso futuro, copie el número
de modelo y el número de serie de la podadora tractor a
continuación:
Podadora tractor modelo númeror:__ __ __ __ ___ __ __
Podadora tractor serie número:___________________
Los números 5º, 6º y 7º de la izquierda en el número
de modelo determinan la serie del modelo de podadora
tractor. Vea la Figura 2.
Cuando complete el número de modelo en el espacio
que se suministra más arriba, el número de serie
concreto del modelo debe quedar en el área sombreada
en gris.
Ahora que ha determinado cuál es el modelo de
podadora a la cual usted va a adosar este sistema de
recolección de pasto, observe las instrucciones de
las siguientes páginas de acuerdo con el modelo de
podadora tractor que posee.
NOTA: Las referencias
relativas a los lados
IZQUIERDO y DERECHO
indican los lados izquierdo y
derecho del tractor mirando
hacia adelante desde la
posición del operador.
La referencia al FRENTE
indica el extremo de la
parrilla; la referencia al
lado POSTERIOR indica el
extremo trasero del tractor.
Figura 1
Figura 2
w
w
w.m
td
p
r
o
d
u
c
t
s
.c
om
M
T
D
L
L
C
P
.
O
.
B
O
X
3
6
1
1
3
1
C
L
E
V
E
L
A
N
D
,
O
H
4
4
1
3
6
3
3
0
-
2
2
0
-
4
6
8
3
8
0
0
-
8
0
0
-
7
3
1
0
Placa de modelo
1 3 A M 6 1 9 G 0 0 0
Indicates Model Series 600
Sample Model Number
4
CONTENIDO DE LA CAJA
Antes de comenzar la instalación, retire todas las piezas de la caja para asegurarse de que esté todo.
El contenido de la caja se enumera más abajo y se muestra en la Figura 1. Los números de pieza de los
elementos de ferretería se muestran entre paréntesis.
Un tubo de canal
Un conjunto de canal de descarga
Dos conjuntos de bolsas para recorte de césped
Un tubo de soporte
Un conjunto de cubierta de tolva para recorte de césped
Un soporte de montaje
Tres cuchillas
2
2
Contenido
de la caja
Si le faltan piezas, por
favor, no contacte al
minorista a quien usted
adquirió la unidad.
Llame directamente
a MTD al 1-330-220-
4MTD o comuníquese
de forma gratuita al
1-800-800-7310.
Figura 3
5
2
2
Si le faltan piezas, por
favor, no contacte al
minorista a quien usted
adquirió la unidad.
Llame directamente
a MTD al 1-330-220-
4MTD o comuníquese
de forma gratuita al
1-800-800-7310
NOTA: Para facilitar
el ensamblado se
ha identificado cada
uno de los elementos
mencionados arriba, y
el código de letra aquí
asignado se mantiene
en las instrucciones
para el ensamblado.
LD = Lado derecho
LI = Lado izquierdo
CONTENIDO DEL PAQUETE DE ELEMENTOS DE FERRETERÍA
Este juego colector de césped se envía con un paquete de elementos de ferretería. Este paquete de
elementos de ferretería puede contener piezas adicionales para realizar la instalación en una podadora
tractor diferente de la que usted posee. Por favor, controle el paquete de elementos de ferretería con la
siguiente ilustración de acuerdo con su modelo de podadora tractor determinado según se indica en la
sección 1 de este Manual.
Para las plataformas con el pasador del colec-
tor de césped no instalado previamente
Contenido
de la caja
NOTA: Para facilitar el ensamblado se ha identificado cada uno de los elementos mencionados arriba, y el código de
letra aquí asignado se mantiene en las instrucciones para el ensamblado.
LD = Lado derecho (#) = Cantidad
LI = Lado izquierdo
Únicamente para los tractores más antiguos
D
F3
F2 F1
(LI) (LD)
A
B
C
E
H
G
(1)
(1)
(1)
(1)(1)
(2)
(2)
(4)
(2)
(2)
Figura 4
Para todos los tractores de las series de modelos 820 a
849 inclusive
Para todos los tractores de las series de modelos
650 a 699 inclusive
A
B
C
(2)
(2)
(2)
6
3
3
Instalación
Conjunto de
soporte
Modelos series 600 a 619
inclusive
IMPORTANTE:
Antes del ensamblado,
coloque el tractor sobre una
superficie firme y nivelada,
desenganche la toma de
fuerza (PTO), detenga el
motor del tractor y coloque
el freno de estaciona-
miento.
NOTA:
Hay dos orificios en el
pasador de horquilla.
Asegúrese de insertar el
broche de horquilla en el
orificio superior para fijar
adecuadamente el conjunto
del soporte a la placa de
enganche.
Instalación del conjunto
del soporte
Modelo Series 600 a 619 inclusive
Modelo Series 800 a 819 inclusive
IMPORTANTE: Antes del ensamblado, coloque el trac-
tor sobre una superficie firme y nivelada, desenganche
la toma de fuerza (PTO), detenga el motor del tractor y
coloque el freno de estacionamiento.
1. Para mayor comodidad, gire el asiento hacia adel-
ante y déjelo en esa posición hasta que el colector
de pasto esté totalmente colocado y ensamblado.
2. Retire el broche de horquilla y el pasador de horquilla
de la parte posterior del conjunto del soporte de
montaje. Vea la Figura 5.
3. Coloque los extremos enganchados del conjunto del
soporte por encima de los pernos con reborde (1).
Gire hacia adentro la parte inferior del conjunto del
soporte hacia abajo y hacia adentro (2) por encima
de la placa de enganche y alinéela con el orificio de
la placa de enganche. Vea la Figura 5.
4. Reinserte el pasador de horquilla a través de los
orificios alineados en el conjunto del soporte y en
la placa de enganche y ajústelo con el broche de
horquilla que se retiró antes. Consulte la Figura 6.
NOTA: : Hay dos orificios en el pasador de horquilla.
Asegúrese de insertar el broche de horquilla en el
orificio superior para fijar adecuadamente el conjunto
del soporte a la placa de enganche.
Figura 5
Figura 6
Figura 7
Figura 8
Orifi cio superior
Placa de
enganche
Exterior del soporte
Orificio exterior
Modelo series 650 a 699 inclusive
El grá co a continuación coordina con las instrucciones para los modelos series 650 a 699 inclusive, que
comienzan en la página siguiente
Soporte
Tornillos
retirados
previamente
Retire el
pasador
RETIRE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

MTD OHD-190-182 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues