Hilti 3565218 Mode d'emploi

SID 14A

SID 18A

SIW 14A

SIW 18A

Original operating instructions en

Mode d'emploi original fr

Manual de instrucciones original es

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

1

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

2

3

4

5

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

6

7

8

9

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

10

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

SID 14A

SID 18A

SIW 14A

SIW 18A

English ................................................. 1

Français ............................................... 17

Español ................................................ 35

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

1

1 Information about the documentation

1.1 Conventions

1.1.1 Warning signs

The following warning signs are used:

General warning

1.1.2 Symbols

The following symbols are used:

Read the operating instructions before use.

Instructions for use and other useful information

Rated speed under no load

Revolutions per minute

Direct current (DC)

1.1.3 Typographic emphasis

The following typographic features are used to emphasize important pas-

sages in the technical documentation about your impact screwdriver/wrench:

1

These numbers refer to the corresponding illustrations.

1.2 Operating instructions

▶ It is essential that the operating instructions are read before initial

operation.

▶ Always keep these operating instructions together with the tool.

▶ Ensure that the operating instructions are with the tool when it is

given to other persons.

Changes and errors excepted.

1.3 Product information

The type designation can be found on the type identification plate at the

base of the tool and the serial number on the side of the casing.

▶ Make a note of this data in the following table and always refer to it when

making an enquiry to your Hilti representative or Hilti Service Center.

Product information

Type:

Generation: 01

Serial no.:

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

2

2 Safety

2.1 Warnings

The purpose of warnings

Warnings alert persons to hazards that occur when handling or using the

product.

Description of the key words used

DANGER

Draws attention to imminent danger that will lead to serious personal

injury or fatality.

WARNING

Draws attention to a potentially dangerous situation that could lead to

serious personal injury or fatality.

CAUTION

Draws attention to a potentially dangerous situation that could lead to

slight personal injury or damage to the equipment or other property.

2.2 Safety instructions

The safety rules given in the following section contain all general safety rules

for electric tools which, in accordance with the applicable standards, require

to be listed in the operating instructions. Accordingly, some of the rules

listed may not be relevant to this electric tool.

2.2.1 General power tool safety warnings

WARNING

Read all safety warnings and all instructions. Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power tool.

Work area safety

▶ Keep work area clean and well lit. Cluttered or dark areas invite

accidents.

▶ Do not operate power tools in explosive atmospheres, such as in

thepresenceofflammableliquids,gasesordust.Power tools create

sparks which may ignite the dust or fumes.

▶ Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

Electrical safety

▶ Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will reduce risk of electric

shock.

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

3

▶ Avoid body contact with earthed or grounded surfaces, such as

pipes, radiators, ranges and refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

▶ Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

▶ Do not abuse the cord. Never use the cord for carrying, pulling or

unplugging the power tool. Keep cord away from heat, oil, sharp

edges or moving parts. Damaged or entangled cords increase the risk

of electric shock.

▶ When operating a power tool outdoors, use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use reduces the risk

of electric shock.

▶ If operating a power tool in a damp location is unavoidable, use

a residual current device (RCD) protected supply. Use of an RCD

reduces the risk of electric shock.

Personal safety

▶ Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired

or under the influence of drugs, alcohol or medication. Amoment

of inattention while operating power tools may result in serious personal

injury.

▶ Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate conditions will reduce

personal injuries.

▶ Prevent unintentional starting. Ensure the switch is in the off‐position

before connecting to power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your finger on the switch

or energising power tools that have the switch on invites accidents.

▶ Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

▶ Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

▶ Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

▶ If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of dust collection can reduce dust-related hazards.

Power tool use and care

▶ Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

4

▶ Do not use the power tool if the switch does not turn it on and off.

Any power tool that cannot be controlled with the switch is dangerous

and must be repaired.

▶ Disconnect the plug from the power source and/or the battery

pack from the power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

▶ Store idle power tools out of the reach of children and do not

allow persons unfamiliar with the power tool or these instructions

to operate the power tool. Power tools are dangerous in the hands of

untrained users.

▶ Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly maintained power

tools.

▶ Keep cutting tools sharp and clean. Properly maintained cutting tools

with sharp cutting edges are less likely to bind and are easier to control.

▶ Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and

theworktobeperformed.Use of the power tool for operations different

from those intended could result in a hazardous situation.

Battery tool use and care

▶ Recharge only with the charger specified by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of

fire when used with another battery pack.

▶ Use power tools only with specifically designated battery packs. Use

of any other battery packs may create a risk of injury and fire.

▶ When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small

metal objects, that can make a connection from one terminal to

another. Shorting the battery terminals together may cause burns or a

fire.

▶ Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If

liquid contacts eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns.

Service

▶ Have your power tool serviced by a qualified repair person using only

identical replacement parts. This will ensure that the safety of the power

tool is maintained.

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

5

2.2.2 Warnings for drivers

▶ Hold power tool by insulated gripping surfaces, when performing an

operation where the fastener may contact hidden wiring or its own

cord. Fasteners contacting a "live" wire may make exposed metal parts

of the power tool "live" and could give the operator an electric shock.

2.2.3 Additional safety instructions

Personal safety

▶ Tampering with or modification of the tool is not permitted.

▶ Wear ear protectors. Exposure to noise can cause hearing loss.

▶ Respiratory protection must be worn if the power tool is used without

a dust removal system for work that creates dust.

▶ Improve the blood circulation in your fingers by relaxing your hands

and exercising your fingers during breaks between working.

▶ Avoid touching rotating parts. Switch the power tool on only after

bringing it into position at the workpiece. Touching rotating parts,

especially rotating accessory tools, may lead to injury.

▶ Activate the safety lock (forward/reverse selector switch in the middle

position) when changing accessory tools or batteries and before

storage or transportation of the power tool.

▶ The power tool is not intended for use by debilitated persons who

have received no special training. Keep the power tool out of reach

of children.

▶ Dust from materials, such as paint containing lead, some wood species,

concrete/masonry/stone containing silica, and minerals as well as metal,

may be harmful. Contact with or inhalation of the dust may cause

allergic reactions and/or respiratory or other diseases to the operator or

bystanders. Certain kinds of dust such as oak and beech wood dust

are classified as carcinogenic, especially in conjunction with additives

for wood conditioning (chromate, wood preservative). Material containing

asbestos may be handled only by specialists. Use a dust removal system

whenever possible. To achieve a high level of dust collection, use a

suitable vacuum cleaner. If necessary, wear a respirator appropriate

for the type of dust generated. Ensure that the workplace is well

ventilated. Follow national requirements for the materials you want

to work with.

▶ The user and any other persons in the vicinity must wear suitable

eye protection, a hard hat, ear protection, protective gloves and

breathing protection while the power tool is in use.

Use and care of electric tools

▶ Secure the workpiece. Use clamps or a vice to hold the workpiece

in position. The workpiece is thus held more securely than by hand and

both hands remain free to operate the power tool.

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

6

▶ Check that accessory tools are compatible with the power tool’s

chuck/drive system and that they are fitted and secured correctly.

▶ Make sure that the screws or bolts and the workpiece are suitable for

the level of torque generated by the power tool. Excessive torque may

overstress, stretch or strip the screws/bolts or damage the workpiece,

thus leading to hazardous situations.

Use and care of battery-powered devices

▶ Check that the tool is switched off before inserting the battery.

Inserting a battery into an electric tool that is switched on can lead to

accidents.

▶ Do not expose batteries to high temperatures and keep them away

from fire. There is a risk of explosion.

▶ Do not disassemble, squash or incinerate batteries and do not subject

them to temperatures over 80°C (176°F). This presents a risk of fire,

explosion or injury through contact with caustic substances.

▶ Avoid ingress of moisture. Ingress of moisture may cause a short circuit,

resulting in burning injuries or fire.

▶ Remove the battery before storing or transporting the power tool.

▶ Avoid short circuiting the battery terminals. Check that the battery

terminals and the terminals in the power tool are free from foreign

objects before inserting the battery in the tool. Short circuiting the

battery terminals presents a risk of fire, explosion and chemical burns.

▶ Do not continue to use or attempt to charge damaged batteries (e.g.

batteries with cracks, broken parts, bent or pushed-in/pulled-out

contacts).

▶ If the battery is too hot to touch it may be defective. In this case, place the

power tool in a non-flammable location, well away from flammable

materials, where it can be kept under observation and allowed to

cool down. Contact HiltiService after the battery has cooled down.

Electrical safety

▶ Before beginning work, check the working area (e.g. using a metal

detector) to ensure that no concealed electric cables or gas and

water pipes are present. External metal parts of the power tool may

become live, for example, when an electric cable is damaged accidentally.

This presents a serious risk of electric shock.

3 Description

3.1 Overview of the product 1

@ Hex. socket (SID)

; Illumination

= Forward/reverse selector

switch with safety lock

% Control switch (with electronic

speed control)

& Square drive (SIW)

( Torque selector button

) Belt hook (optional)

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

7

+ Battery charge status display

§ Release buttons (B18/… bat-

tery)

/ Release button (B14/… bat-

tery)

3.2 Intended use

The product described is a hand-held, cordless impact screwdriver/wrench

for driving and removing screws or tightening and releasing threaded nuts

and bolts in wood, metal, masonry and concrete.

Hilti products are designed for professional use and may be operated, ser-

viced and maintained only by trained, authorized personnel. This personnel

must be informed of any particular hazards that may be encountered. The

impact screwdriver/wrench and its ancillary equipment may present hazards

when used incorrectly by untrained personnel or when used not as directed.

▶ Do not use the battery as a power source for other unspecified appliances.

▶ Observe the national health and safety requirements.

▶ To reduce the risk of injury, use only genuine Hilti tools and accessories.

▶ To power the impact screwdriver/wrench, use a rechargeable battery of a

type approved by Hilti and a charger from the C4/36 series.

Note

Make sure that the outer surfaces of the battery are clean and dry

before inserting the battery in an approved battery charger.

Read the operating instructions for the charger for further information

about the charging procedure.

If the power tool is used for applications that require a specific torque, or

where a certain maximum torque must not be exceeded, there is a risk of

over-tightening and damage to the screw or workpiece.

▶ Do not use the power tool for applications that require a precise or

specified torque. Instead, use a tool that allows the torque to be set as

required.

3.3 Charge status display

The charge status of the Liion battery is displayed after pressing one of the

release buttons lightly (press only until slight resistance is felt).

Status Meaning

4 LEDs light. • Charge status: 75 % to 100 %

3 LEDs light. • Charge status: 50 % to 75 %

2 LEDs light. • Charge status: 25 % to 50 %

1 LED lights. • Charge status: 10 % to 25 %

1 LED blinks. • Charge status: < 10 %

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

8

Note

Battery charge status cannot be displayed while the control switch is

pressed and for up to 5 seconds after releasing the control switch.

3.4 Items supplied

Impact screwdriver/wrench, operating instructions.

Note

To help ensure safe and reliable operation, use only genuine Hilti spare

parts and consumables. Spare parts, consumables and accessories

approved by us for use with the product can be found at your local Hilti

Center or online at: www.hilti.com

4 Technical data

4.1 Impact screwdriver/wrench

SID 14A SIW 14A

Rated voltage

14.4 V 14.4 V

Weight (including battery and

chuck)

2.9 lb

(1.3 kg)

2.9 lb

(1.3 kg)

Rated speed un-

der no load

Setting I

0Hz…16.7Hz

(0 rpm …

1,000 rpm)

0Hz…16.7Hz

(0 rpm …

1,000 rpm)

Setting II

0Hz…25.0Hz

(0 rpm …

1,500 rpm)

0Hz…25.0Hz

(0 rpm …

1,500 rpm)

Setting III

0Hz…41.7Hz

(0 rpm …

2,500 rpm)

0Hz…38.3Hz

(0 rpm …

2,300 rpm)

Impact speed

≤ 3,100 bpm ≤ 3,400 bpm

Torque adjustment

3settings 3 settings

Large standard bolts

M8 to M16 M8 to M16

Large high-strength bolts

M6 to M12 M6 to M12

Socket/bit drive

1

/

4

″hex.socket

with locking ring

1

/

2

″squaredrive

with ball-notch

retention

or

3

/

8

″squaredrive

with locking ring

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

9

SID 18A SIW 18A

Rated voltage

21.6 V 21.6 V

Weight (including battery and

chuck)

3.3 lb

(1.5 kg)

3.3 lb

(1.5 kg)

Rated speed un-

der no load

Setting I

0 Hz … 16.7 Hz

(0 rpm …

1,000 rpm)

0 Hz … 16.7 Hz

(0 rpm …

1,000 rpm)

Setting II

0 Hz … 25.0 Hz

(0 rpm …

1,500 rpm)

0 Hz … 25.0 Hz

(0 rpm …

1,500 rpm)

Setting III

0 Hz … 41.7 Hz

(0 rpm …

2,500 rpm)

0 Hz … 38.3 Hz

(0 rpm …

2,300 rpm)

Impact speed

≤ 3,450 bpm ≤ 3,500 bpm

Torque adjustment

3 settings 3 settings

Large standard bolts

M8 to M16 M8 to M16

Large high-strength bolts

M6 to M12 M6 to M12

Socket/bit drive

1

/

4

″hex.socket

with locking ring

1

/

2

″squaredrive

with ball-notch

retention

or

3

/

8

″squaredrive

with locking ring

4.2 Setting the torque

The torque is selected by way of the torque selector button.

Model SID …

SID 14A

SID 18A

Model

SID 14A SID 18A

Setting I

37 ft⋅lb

f

(50 N⋅m)

44 ft⋅lb

f

(60 N⋅m)

Setting II

74 ft⋅lb

f

(100 N⋅m)

81 ft⋅lb

f

(110 N⋅m)

Setting III

111 ft⋅lb

f

(150 N⋅m)

122 ft⋅lb

f

(165 N⋅m)

Model SIW …

SIW 14A

SIW 18A

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

10

SIW 14A SIW 18A

1/2″ square

drive with

ball-notch

retention

3/8″ square

drive with

locking ring

1/2″ square

drive with

ball-notch

retention

3/8″ square

drive with

locking ring

Setting I

59 ft⋅lb

f

(80 N⋅m)

48 ft⋅lb

f

(65 N⋅m)

66 ft⋅lb

f

(90 N⋅m)

55 ft⋅lb

f

(75 N⋅m)

Setting II

89 ft⋅lb

f

(120 N⋅m)

85 ft⋅lb

f

(115 N⋅m)

100 ft⋅lb

f

(135 N⋅m)

89 ft⋅lb

f

(120 N⋅m)

Setting III

136 ft⋅lb

f

(185 N⋅m)

118 ft⋅lb

f

(160 N⋅m)

148 ft⋅lb

f

(200 N⋅m)

129 ft⋅lb

f

(175 N⋅m)

4.3 Battery

B 14/1.6

Li-Ion

B 14/3.3

LiIon

B 18/1.6

LiIon

B 18/2.6

LiIon (01)

Rated voltage

14.4 V 14.4 V 21.6 V 21.6 V

Capacity

1.6 A⋅h 3.3 A⋅h 1.6 A⋅h 2.6 A⋅h

Energy capacity

23.04 W⋅h 47.52 W⋅h 34.56 W⋅h 56.16 W⋅h

Weight

0.79 lb

(0.36 kg)

1.30 lb

(0.59 kg)

1.06 lb

(0.48 kg)

1.72 lb

(0.78 kg)

B 18/2.6 LiIon

(02)

B 18/3.3 Li-Ion B 18/5.2 Li-

Ion (01)

Rated voltage

21.6 V 21.6 V 21.6 V

Capacity

2.6 A⋅h 3.3 A⋅h 5.2 A⋅h

Energy capacity

56.16 W⋅h 71.28 W⋅h 112.32 W⋅h

Weight

1.06 lb

(0.48 kg)

1.72 lb

(0.78 kg)

1.72 lb

(0.78 kg)

5 Operation

5.1 Inserting the battery 2

WARNING

Risk of injury! Inadvertent starting of the impact screwdriver.

▶ Before fitting the battery, check that the cordless impact screwdriver

is switched off and that the forward/reverse switch is in the middle

position (i.e. safety lock engaged).

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

11

WARNING

Electrical hazards! Risk of short circuiting.

▶ Before inserting the battery, check to ensure that the battery terminals

and the contacts in the impact screwdriver are free from foreign

objects.

WARNING

Risk of injury! Hazard presented by a falling battery.

▶ A falling battery may present a risk of injury to yourself and others.

Check that the battery is securely seated in the power tool.

▶ Fit the battery and make sure that it is heard to engage.

5.2 Fitting the belt hook (optional) 3

WARNING

Risk of injury! Hazard presented by a falling power tool.

▶ A falling power tool may present a risk of injury to yourself and others.

Check that the belt hook is fitted securely before beginning work.

Note

The belt hook allows the power tool to be attached to a belt worn by

the operator. The belt hook can be fitted to allow attachment on the left

or right side of the body.

▶ Fit the belt hook.

5.3 Fitting an accessory tool 4

SID 14A

SID 18A

1. Check that the connection end of the accessory tool is clean.

Result

The connection end is dirty.

▶ Clean the connection end.

2. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

3. Push the accessory tool into the chuck as far as it will go (until it engages).

5.4 Removing the accessory tool 5

SID 14A

SID 18A

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

12

CAUTION

Risk of injury. The accessory tool may be hot or have sharp edges.

▶ Wear protective gloves when using the power tool and when changing

accessory tools.

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

2. Pull the chuck ring forward and hold it in this position.

3. Pull the accessory tool out of the chuck.

4. Release the chuck ring.

5.5 Fitting an accessory tool 6

SIW 14A

SIW 18A

1. Check that the connection end of the accessory tool is clean.

Result

The connection end is dirty.

▶ Clean the connection end.

2. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

3. Bring the notch in the accessory tool into alignment with the ball on the

square drive.

4. Push the accessory tool onto the square drive until it engages.

5.6 Removing the accessory tool 7

SIW 14A

SIW 18A

CAUTION

Risk of injury. The accessory tool may be hot or have sharp edges.

▶ Wear protective gloves when using the power tool and when changing

accessory tools.

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

2. Pull the accessory tool off the square drive.

5.7 Setting the torque 8

Technical data

Model SID … (SID 14A OR SID 18A) → Seite 9

Model SIW … (SIW 14A OR SIW 18A) → Seite 9

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

13

▶ Press the torque selector button as many times as necessary until the

desired torque setting is indicated to the left of the button.

SID 14A

SID 18A

Model SID … (SID 14A OR SID 18A) → Seite 9

SIW 14A

SIW 18A

Model SIW … (SIW 14A OR SIW 18A) → Seite 9

5.8 Setting forward or reverse rotation 9

Note

An interlock prevents switching while the motor is running.

The control switch is locked when the forward/reverse switch is in the

middle position (safety lock).

▶ Set the forward/reverse switch to the desired direction of rotation.

5.9 Screwdriving

WARNING

Risk of injury and damage. Screws/bolts or the workpiece may be

damaged by excessively high torque; this may also lead to serious injury.

▶ Ensure fastener and attachment will withstand the level of torque

generated by the tool.

1. Set the forward/reverse switch to the middle position or remove the

battery from the power tool.

2. Use the torque selector button to set the desired torque. → Seite 12

5.10 Switching on

▶ Press the control switch.

◁ Speed of rotation is regulated by the distance the control switch is

pressed in.

5.11 Switching off

▶ Release the control switch.

5.12 Removing the battery 10

▶ Remove the battery.

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

14

6 Care, maintenance, transport and storage

6.1 Care and maintenance of the tool

WARNING

Electrical hazards! Improper repairs to electrical parts may lead to

serious injuries.

▶ Electrical parts may be repaired only by trained electrical specialists.

▶ Keep the tool, especially its grip surfaces, clean and free from oil and

grease. Do not use cleaning agents containing silicone.

▶ Never operate the power tool when the ventilation slots are blocked.

Clean the air vents carefully using a dry brush. Do not permit foreign

objects to enter the interior of the tool.

▶ Clean the outer surfaces of the tool with a slightly damp cloth at regular

intervals.

6.2 Care of the Liion battery

▶ Keep the battery clean and free from oil and grease.

▶ Clean the outer surfaces of the tool with a slightly damp cloth at regular

intervals. Do not use cleaning agents containing silicone.

▶ To achieve maximum battery life, stop drawing power from the battery as

soon as a significant drop in the performance of the power tool is noticed.

▶ Charge the batteries using the Hilti chargers approved for use with Li-ion

batteries.

6.3 Transport and storage

WARNING

Risk of fire! Risk of short circuiting.

▶ To avoid short circuits and associated heat generation, Li-ion bat-

teries should never be stored or transported in loose, bulk form and

without protective measures.

▶ Remove the battery before transporting or storing the impact screw-

driver/wrench.

Printed: 16.06.2015 | Doc-Nr: PUB / 5070694 / 000 / 03

La page charge ...

Hilti 3565218 Mode d'emploi

Ce manuel convient également à

Hilti 3565218 Mode d'emploi

dans d''autres langues

Documents connexes