Maytag MHW5400D Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
se Care ide
ided'utilisation d'entretien
FRONT-LOADINGAUTOMATICWASHER
LAVEUSEAUTOMATIO.UEDECHARGElViENTFRONTAL
Para obtener acceso
al Manual de uso v cuidado
en espanol, o para obtener
informaci6n adicional acerca
de su producto, visite:
www.maytag.com
If you have any problems or questions, visit us at www.maytag.com
Pour tout probleme ou question, consulter www.maytag.ca
W10649249B
W10649250B-SP
Designed to use only HE
High Efficiency detergents.
Con£ue pour I'utilisation
d'un d_tergent haute
efficacit_ seulement.
NSF Protocol P351 Protocole NSF P351
Allergen Reduction Performance of Residential Performance de reduction des allergSnes pour les laveuses
and Commercial, Family-Sized Clothes Washers de format familial & usage residentiel ou commercial
TABLEOF CONTENTS
WASHERSAFETY..................................................................................2
ACCESSORIES.......................................................................................3
CONTROL PANELAND FEATURES.................................................4
USING THE DISPENSER DRAWER.................................................6
CYCLEGUIDE..........................................................................................7
USING YOUR WASHER.......................................................................9
WASHER MAINTENANCE................................................................13
TROUBLESHOOTING........................................................................16
WARRANTY...........................................................................................23
ASSISTANCEOR SERVICE............................................. BackCover
TABLEDE MATIERES
SECURITEDE LA LAVEUSE.............................................................24
ACCESSOIRES....................................................................................25
TABLEAUDECOMMANDE ETCARACTERISTIQUES............26
UTILISATIONDUTIROIRDU DISTRIBUTEUR...........................29
GUIDE DE PROGRAMMES.............................................................29
UTILISATIONDE LALAVEUSE........................................................32
ENTRETIENDE LALAVEUSE..........................................................36
DEPANNAGE.........................................................................................39
GARANTIE..............................................................................................50
ASSISTANCEOU SERVICE................................. Couverturearriere
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
"WARNING." These words mean:
You can be kiJled or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
iMPORTANT SAFETY iNSTRUCTiONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry=cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach intothe washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where it will be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" located in the installation
instructionsfor grounding instructions.
this time.
SAVE THESE iNSTRUCTiONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
ACCESSORIES
Customize your new washer and dryer with the following
genuine Maytag accessories. For more information on options
and ordering, contact your dealer, call us at 1-800-901-2042,
or visit: www.maytag.com/accessones.
In Canada, call 1-800-807-6777, or visit: www.maytag.ca.
15" Pedestal
Color-matched pedestals raise the washer
and dryer to a more comfortable working
height. The large drawer provides convenient
storage.
Stack Kit
If space is at a premium, the stack kit
allows the dryer to be installed on top
of the washer.
CONTROLPANELAND FEATURES
Not all features and cycles are avadable on all models,
NOTE: The control panel features a sensitive surface that responds to a light touch of your finger, To ensure your selections are registered,
touch the control panel with your finger tip, not your fingernail, When selecting a setting or option, simply touch its name.
Model MHW71 00D
Model MHW5400D
L......L_'-
Model MHW4100D
[
PowerWash co [d
wash
bedd,_g wrlr_k[ _
r_ontrol
,ap_o ",Jeh_ates
Nag!]
_aqlrlZe
d_OIP _[eaN _=:_3her
i
I,,11
hold tostart
_)
e_t_a
i Low h_gh%_ln _,peed w _ m
r----J
0
eftra _ _ 8P'ay
' .......
r, add a _- m_nt
I .... i
I'b"_! I
POWER/CANCEL
Touch to turn the washer on and off. Touch to stop/cancel
a cycle at any hme.
NOTE: Turning the Wash Cycle knob wdl also turn the washer
on and off.
O
WASH CYCLE KNOB
Turn the knob to select a cycle for your laundry load.
An LED wdl hght up for the cycle selected.
NOTE: The Clean Washer with affresh _ LED will flash when the
washer has run 30 wash cycles as a reminder to run the Clean
Washer with affresh _cycle.
See "Cycle Guide" for detaded descriphons of cycles.
NOTE: For best results when using the Overnight Wash & Dry
cycle, use for loads weighing 2.5 pounds and less, such as a
soccer uniform or a running tank and shorts.
4
O START
Touch and holduntilthe lightabove START comes on tostarta
cycle,or touchonce whilea cycleisinprocess topause it.Ifyou
want to add a garment,you can touch START when the "Add a
Garment" LED ison.
O LED DISPLAY AND SETTINGS
When you select a cycle, its default settings will light up and the
Estimated Cycle Time will be displayed. Factors such as load size,
wash temperature, and water pressure may affect the time shown in
the display during the cycle. Tightly packing garments, unbalanced
loads, or excessive suds may cause the washer to adjust the cycle
time, as well.
Touch the desired setting along the right of the display to adjust.
See "Cycle Guide" for available settings on each cycle. Not all
settings are available with all cycles.
Temperature
The recommended wash temperature is preset for each cycle. You
may also select a wash temperature based on the type of fabric
and soils being washed. For best results, follow the garment label
instructions. All wash temperatures feature a cold rinse.
Soil Level
The Soil Level setting (wash time) is preset for each wash cycle.
For most loads, use this preset soil level. When you change the
soil setting, the cycle time will increase or decrease in the Estimated
Cycle Time display.
For heavily soiled and sturdy fabrics, use the Soil Level setting to
select more wash time. For lightly soiled and delicate fabrics, use
the Soil Level setting to select less wash time. Lower soil level
settings will help reduce tangling and wrinkling.
Spin Speed
This washer automatically selects the spin speed based on the
cycle selected. Some preset speeds can be changed.
[] Higher spin speeds mean shorter dry times, but may
increase wrinkling in your load.
[] Lower spin speeds reduce wrinkling, but will leave
your load more damp.
DELAY START
Use + and - to delay the start of the wash cycle by 9 to 12 hours,
depending on model. To turn off Delay Start, use + and - to set the
delay time to "01'or touch POWER/CANCEL
O CYCLE STATUS LIGHTS
NOTE: Not all Cycle Status Lights are available
on all models. iiiiiiii_i__i_i!!_i!_ii_!!_!!!!!_!__!!_____i_!__i__i__i__i__i__i__i__i__i__i__i__i__i__i__i_i__i_ii__ii_i__i__i__i__i__i__i__i__i__i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_ii
_!i¸!i¸!i¸!_!!_!_ii!_i_i_i!_ii_i_ii_ii_ii!_i_i_i_i_i_i_i_i_i_i_!i_!i_!i!_!_i!_i!_i!_i!_i!_i;_!_i_i!i
Delay
If a Delay Start is set, the Delay indicator will
light and the delay time will count down in the
display.
Door Locked
Door Locked will light to indicate that the door
is locked and cannot be opened without first
pausing or canceling the cycle.
Sensing
When START is touched and held, the washer
will first perform a self-test on the door lock
mechanism and the sensing light will come on.
You will hear a click, the drum will make a partial turn, and the
door will click again as it unlocks briefly. The door will click one
more time when it locks again.
Once the door has locked the second time, the washer will
begin tumbling and adding water. This sensing process will
continue throughout the cycle. You may also hear water flowing
through the dispenser, adding detergent to the load.
After the load size is sensed, the estimated time based on load
size will be displayed. The actual cycle time may be lengthened;
however, the display will continue to show the estimated time.
The sensing light will blink once a second at various times
during the cycle, such as when the washer is reducing extra
suds.
0
Add a Garment
When "Add a Garment" is lit, you may pause the washer, open
the door, and add items. Touch and hold START to start the
washer again.
Steaming
This will light to show that the cycle is using a steam boost for
added cleaning power.
Done
Once the cycle is complete, this light will come on. Remove
the load promptly for best results. The Done indicator is also lit
during Fresh Hold :" or Fresh Spin TM option.
OPTIONS
Touch to activate additional wash options or additional features on
the washer. Not all options are available on all models.
Fresh Hold _ Option (on some models)
The Fresh Hold _ option will periodically tumble the load after
the end of the cycle for 12 hours while the integrated fan
circulates air through the washer to reduce humidity. To turn
on the Fresh Hold :"option, touch Fresh Hold. If, however, the
Fresh Hold :" option is turned on, it will stay on for all future
cycles until turned back off - the washer remembers the last
on/off status set. To turn off the Fresh Hold :" option, touch
Fresh Hold.
You may also activate the Fresh Hold _option without running
a cycle by touching and holding POWER/CANCEL for one
second, then touching and holding Fresh Hold for 3 seconds,
then touching and holding START for 3 seconds.
To turn off the Fresh Hold" option when it is running, touch
POWER/CANCEL.
NOTE: The door will lock while the Fresh Hold _option is
active. To cancel the option and unlock the door, touch
POWER/CANCEL
Fresh Spin TM Option (on some models)
The Fresh Spin T''option will periodically tumble the load after
the end of the cycle for up to 6 hours to reduce humidity.
To turn on the Fresh Spin T''option, touch Fresh Spin.
If, however, the Fresh Spin TM option is turned on, it will stay
on for all future cycles until turned back off - the washer
remembers the last on/off status set. To turn off the Fresh
Spin TM option, touch Fresh Spin.
You may also activate the Fresh Spin T''option without
running a cycle by touching and holding POWER/CANCEL
for one second, then touching and holding Fresh Spin for
3 seconds, then touching and holding START for 3 seconds.
To turn off the Fresh Spin"' option when it is running, touch
POWER/CANCEL.
NOTE: The door will lock while the FreshSpin T''option is active.
Tocancel the option and unlock the door, touch POWER/
CANCEL.
_ team for Stains
The Steam for Stains option adds additional soak and
wash time to many cycles to help remove tough stains, as well
as a steam boost for added cleaning power. An integrated
heater helps to maintain optimal wash temperatures. See the
"Cycle Guide" for cycles that allow the Steam for Stains option.
_ Extra Rinse
Activate this option to add an extra rinse to most cycles.
_ ycle Signal
Use this option to turn on or off the signal that sounds at end
of cycle.
To turn off the tones that sound when a setting is touched:
Touch and hold CYCLE SIGNAL for about 3 seconds.
Repeat to turn them on.
_ Control Lock
Touch and hold for 3 seconds to lock the controls
to avoid unwanted changes or operation. Touch and hold
3 seconds again to unlock. For each second CONTROL
LOCK is held down, the display will count down one
second: you will see "3_' then "2_' then "1 _'You may
still touch START to pause the cycle, or touch POWER/
CANCEL to turn off the washer. 5
CONTROLPANELAND FEATURES
_HE detergent
_ Liquid fabric
softener
_ Chlorine bleach
O DISPENSER DRAWER
The dispenser drawer gives you the convenience of automatically
adding HE detergent, liquid chlorine bleach, and liquid fabric
softener to the wash bad at the proper time. See "Using the
Dispenser Drawer" for information on using the dispenser drawer.
@
High Efficiency "H E" detergent compartment
This compartment holds liquid or powdered HE detergent for
your main wash cycle.
Liquid fabric softener compartment
AutomaticaJiy dilutes and dispenses Jiquid fabric softener at
the optimum time in the cycle.
m Use onJy liquid fabric softener in this dispenser.
m
Liquid chlorine bleach compartment
AutomaticaJiy dilutes and dispenses Jiquid chJorine bJeach at
the optimum time during the first rinse after the wash cycle.
This compartment cannot dilute powdered bJeach,
Choosing the Right Detergent
Use only High Efficiency detergents. The package will be marked
"HE" or "High Efficiency/' Low-water washing creates excessive
sudsing with a non-HE detergent. Using non-HE detergent will likely
result in longer cycle times and reduced rinsing performance, it may
also result in component failure and, over time, buildup of mold or
mildew. HE detergents are low-sudsing and quick-dispersing to
produce the right amount of suds for the best performance. They
hold soil in suspension so it is not re-deposited onto clean clothes.
Follow the manufacturer's instructions to determine the amount of
detergent to use.
Use only High Efficiency (HE) detergent.
USING THE DISPENSER DRAWER
1. Open the dispenser drawer.
2. Add laundry products as described in steps 4-6 in the
"Using Your Washer" section.
3. Slowly close the dispenser drawer. Make sure it is
completely closed.
NOTE: A small amount of water may remain inthe dispensers from
the previous wash cycle. This is normal.
Adding H E detergent to dispenser
O
SeJector
Pour a measured amount of HE
detergent into detergent compartment.
For powdered detergent, lift the selector
to the high position, For liquid detergent,
push down the selector to the low
position,
[H E detergent
compartment
Use on/y High Efficiency
(HE) detergent.
SeJector
in low
Powdered detergent:
Lift the seJector to the high
position.
Liquid detergent:
Push down the seJector to the
Jow position.
Do not overfill; adding too much detergent may cause
detergent to be dispensed into the washer too early,
IMPO RTANT:
m Do not add single-dose laundry packet to dispenser drawer,
m Use powdered detergent when using the Delay Start option,
Liquid detergent may seep out before the wash begins,
CYCLEGUIDE
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings that best
fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.
NOTES:
[] Not all cycles and options are available on all models
[] All wash temperature selections feature a cold rinse.
[] Not all temperatures or spin speeds are labeled on the control panel.
F i
terns to wash I
using default Wash Sp n Soi Available
cyclesetUngs: ! Cycle:. Temperature: . Speed: . Level: . Options: . Cycle Details:
Normally soiled
cottons, linens,
sheets, and mixed
garment loads
Bright or darkly
colored cottons,
linens, casual and
mixed loads.
Lightly soiled shirts,
blouses, trousers,
pants, and dresses
Sheer fabrics,
lingerie, sweaters,
and lightly-soiled
shirts, blouses,
trousers, pants,
and skirts
Normally soiled
sheets, pillowcases,
light blankets, or
throws
Small loads of
2-4 lightly soiled
garments
Normal Extra Hot
Hot
Warm
Cool
Cold
Cold Cold
Wash
Wrinkle Extra Hot
Control Hot
Warm
Cool
Cold
Delicates Extra Hot
Hot
Warm
Cool
Cold
Bedding Extra Hot
Hot
Warm
Cool
Cold
Rapid Extra Hot
Wash Hot
Warm
Cool
Cold
Clean
Washer
with
affresh _R
Max Extract"/
Extra High
High
Med
None
Max ExtractT"/
Extra High
High
Med
None
Max ExtractT_/
Extra High
High
Med
Low
None
Max ExtractT_/
Extra High
High
Med
Low
None
Max ExtractT_/
Extra High
High**
Med
Low
None
Max ExtractTV
Extra High
High
Med
Low
None
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
No clothes in washer
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Fresh Hold°/
Fresh Spin TM
Delay Start
@
This cycle combines medium-
speed tumbling and an extra-high-
speed spin. This cycle is designed
to provide the most energy
efficiency.
@
This cycle uses a concentrated
detergent solution along with cold
water throughout the cycle to
gently lift out stains and care for
fabrics.
@
This cycle combines low-speed
tumbling and medium-speed spin
for gentle fabric care and reduced
wrinkling.
This cycle combines low-speed
tumbling and low-speed spin for
gentle fabric care and reduced
wrinkling.
The wash action of this cycle is
designed to keep large items from
tangling and bailing up.
Q or small loads (2-4 items) needed
quickly. This cycle combines high-
speed tumbling, a shortened wash
time, and an extra-high-speed spin
for reduced drying times.
Use this cycle every 30 washes to
keep the inside of your washer fresh
and clean. This cycle uses a higher
water level. Use with affresh _ washer
cleaner tablet or liquid chlorine bleach
to thoroughly clean the inside of your
washer. This cycle should not be
interrupted. See "Washer Care_'
IMPORTANT: Do not place garments
or other items in the washer during the
Clean Washer with affresh" cycle. Use
this cycle with an empty wash tub. See
"Washer Care" in "Washer MaintenanceS'
* Steam for Stains option is only available when warm, hot, or extra hot water temperature is selected.
** On some models, the default is Extra High.
continued on next page
Load Size Recommendations
For best results, follow the load size recommendations noted for each cycle.
Q Small load: Fill the washer drum with 3-4 items, not than
more
1/4 full.
Medium load: Fill the washer drum to about 1/2 full.
up
Large load: Fill the washer drum up to about 3/4 full.
Extra-large load: Fill the washer drum, but make sure clothes
can tumble freely. For best results, avoid packing tightly.
7
CYCLEGUIDE
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle, options, and settings that best
fit the load being washed. Not all settings are available with each cycle, and some options cannot be used together.
NOTES:
[] Not all cycles and options are available on all models
[] All wash temperature selections feature a cold rinse.
[] Not all temperatures or spin speeds are labeled on the control panel.
cycle settings:
Wet load of clothes
Swimwear, items
that need rinsing
Clothing, bedding
and towels requiring
sanitization
Sturdy garments
and household items
exposed to possible
allergens
2-4 lightly soiled
synthetic garments,
athletic uniforms, or
workout wear
Heavily soiled
fabrics
Cycle:
Drain
& Spin
Drain
& Spin
with
Extra
Rinse
Sanitize
Allergent
Overnight
Wash &
Dry
Power
Wash
Temperature:
N/A
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Extra Hot
Hot
Extra Hot
Hot
Warm
Cool
Cold
Extra Hot
Hot
Warm
Cool
Cold
Speed:
Max ExtractT"/
Extra High
High
Med
Low
None
Max ExtractT"/
Extra High
High
Med
Low
None
Max Extract_V
Extra High
High
Med
Low
None
Max Extract_V
Extra High
High
Med
Max ExtractS"/
Extra High
Max Extract_V
Extra High
High
Med
Low
None
Level:
N/A
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra Heavy
Heavy
Med
Light
Extra
Heavy
Heavy
Med
Light
Options:
Fresh Hold°/
Fresh Spin TM
Delay Start
Fresh HoldR/
Fresh Spin TM
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold
Extra Rinse
Delay Start
Steam for
Stains*
Fresh Hold°/
Fresh Spin TM
Extra Rinse
Delay Start
Cycle Details:
Use Drain & Spin to removeexcess water from the load.
Spin speed can be set to a
lower setting.
@
Select Drain & Spin; then select
Extra Rinse to add water. The
cycle includes an extra-high-speed
spin. For some fabrics, you may
wish to set the spin speed to a
lower setting.
This cycle eliminates 99.990/0 of
the most common bacteria found
in clothes, sheets, and towels.
The extra hot wash temperature
ensures sanifizafion. Check
recommended wash temperature
of your items. Bacteria tested were
K. pneumonia, R aureginosa, and
S. aureus.
Uses more water to flush out
allergens such as dust mites
and pet dander from normally-
soiled items.
Q his short wash cycle has an
extra-high-speed spin followed
by inermitent tumbling and fan
activation to circulate air through
the clothes.
Use this cycle for extremely soiled
garments and household items that
need additional cleaning power.
* Steam for Stains option is only available when warm, hot or extra hot water temperature is selected.
t" Allergen
Allergen cycle certified by NSF International, an independent, third party testing and certification organization. The certification verified that this
cycle reduced tested allergens by at least 95.0% and maintained the water temperature necessary to kill dust mites. Only the allergen cycle has
been designed to meet the requirements of NSF Protocol P351 for Allergen Reduction Performance effectiveness.
8
USINGYOURWASHER
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other fiarnmable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
First wash cycle without laundry
Before washing clothes for the first time, if not completed during
the final installation step, choose the NORMAL cycle and run it
without clothes. Use only HE detergent. Use 1/2 the manufacturer's
recommended amount for a medium-size load. This initial cycle
serves to ensure the interior is clean before washing clothes.
1, Sort and prepare your laundry
Sort items by recommended cycle, water temperature, and
colorfastness. Separate heavily soiled items from lightly soiled.
Separate delicate items from sturdy fabrics. Treat stains promptly
and check for colorfastness by testing stain remover products on
an inside seam.
IMPORTANT:
[] Empty pockets. Loose change, buttons, or any small object can
plug pumps and may require a service call.
[] Close zippers, fasten hooks, tie strings and sashes, and remove
non-washable trim and ornaments.
[] Mend rips and tears to avoid further damage to items
during washing.
[] Turn knits inside out to prevent pilling. Separate lint-takers from
lint-givers. Synthetics, knits, and corduroy fabrics will pick up lint
from towels, rugs, and chenille fabrics.
[] Do not dry garments if stains remain after washing, because heat
can set stains into fabric.
[] Always read and follow fabric care labels and laundry
product instructions. Improper usage may cause damage
to your garments.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
f2, Add laundry products
Single-dose laundry packet, Oxi-type boosters, color-safe bleach,
or fabric softener crystals can be added to the drum prior to
adding laundry.
NOTE: Do not add clothes to washer drum prior to adding
laundry products. Always follow manufacturer's instructions.
3.Load laundry into washer
Place a load of sorted clothes loosely in the washer, items need to
move freely for best cleaning and to reduce wrinkling and tangling.
Close the washer door by pushing it firmly until the latch clicks.
[] Depending on load type and cycle, the washer can be fully
loaded, but not tightly packed. Washer door should close easily.
See "Cycle Guide" for loading suggestions.
[] Mix large and small items and avoid washing single items. Load
evenly.
[] Wash small items in mesh garment bags. For multiple items, use
more than one bag and fill bags equally.
USINGYOURWASHER
USING LAUNDRY PRODUCT DISPENSERS
NOTE: Do not add single-dose laundry packets, Oxi-type boosters,
color-safe bleach, or fabric softener crystals to dispensers. They will
not dispense correctly.
,,_=
4, Add H E detergent
Adjust the selector, based on type of HE detergent used
(either liquid or powdered). See "Using the Dispenser Drawer"
instructions on how to use the dispenser.
(if desired)
Pour a measured amount of liquid fabric softener into liquid fabric
softener compartment. Always follow manufacturer's directions for
correct amount of fabric softener based on your load size.
Fabric softener is always dispensed in the last rinse, even if Extra
Rinse is selected.
IMPORTANT: Do not overfill, dilute, or use more than 1/4 cup
(60 mL) of fabric softener. Do not fill past the MAX line. Overfilling
dispenser will cause fabric softener to immediately dispense into
washer.
[] Do not spill or drip any fabric softener onto the clothes.
[] Do not use liquid fabric softener dispenser balls in this washer.
They will not dispense correctly.
Add liquid chlorine bleach to dispenser
(if desired)
Add liquid chlorine bleach to the bleach compartment. Do not
overfill, dilute, or use more than 2/3 cup (165 mL). Do not use
color-safe bleach or Oxi in the same cycle with liquid chlorine
bleach.
[] Always measure liquid chlorine bleach. Use a measuring cup
with a pour spout; do not guess.
[] Do not fill beyond the "MAX" level. Overfilling could cause
garment damage.
7, Touch POWER/CANCEL to turn on
washer (optional)
power!cancel
Slowly close the dispenser drawer. Make sure the drawer is closed
completely, then touch POWER/CANCEL to turn on the washer or
go to Step 8.
10
f
8, Select CYCLE*
normal
mm
P_w_rWash
overnigh"_
wash & dry
allerge_
sanitize
cold
wash
m
wrinkle
contro!
_e}icates
_edding
Appearance may vary.
Turn cycle knob to select your wash cycle. See "Cycle Guide" for
details on cycle features.
9, Adjust settings, if desired*
extra
( lco[d warm hot
temperature
extra
) light reed heavy
SOil {eve_ m m m
max
I sp,n speed )none reed extract
Appearance may vary.
1 0, Select any additional options*
fresh
m hold
steam
m for stains
am extra
rinse
m cycle
signal
control
m lock
hold 3 sees
Appearance may vary.
To add an option to the cycle, touch its name - Fresh Hold/Fresh
Spin, Steam for Stains, Extra Rinse, Cycle Signal, or Control Lock.
To remove an option from the selected cycle, touch the option
again.
1 1, Setting a delayed start
estimated cycle time
The display will show the default settings for the selected cycle.
To adjust a setting, touch its name - Temperature, Soil Level, or
Spin Speed. Adjusting settings will change the Estimated Cycle
Time. Tightly packing the load, unbalanced loads, or excessive
suds may also cause the washer to increase the cycle time.
If you do not want to begin a cycle immediately, you may choose
the DELAY START option. This will delay the start of the wash
cycle by 9 to 12 hours.
To set a delayed start:
1. Touch DELAY START + and - buttons to set the desired delay
time.
2. Touch and hold START to set the delay.The delay countdown
has started when the START light stops blinking.
*Not all options and settings are available with all cycles.
See "Cycle Guide" for available options and settings.
11
USINGYOURWASHER
1 2, Touch and hold START to begin
wash cycle
hold to start
Touch and hold START to start the wash cycle. To pause
a cycle in progress, touch START once, then touch and
hold again to continue the cycle. To cancel a cycle, touch
POWER/CANCEL
Once you touch and hold START, you will hear the door lock,
unlock, and lock again. The washer door will remain locked
during the wash cycle.
Unlocking the door to add garments:
Ifyou need to open the door to add 1 or 2
missed garments, you may do so while the
"Add a Garment" light is lit.
.- add a garment
Touch START once; the door will unlock
once the washer movement has stopped.
This may take several minutes. Then close
door and touch and hold START again to
restart the cycle.
hold to start
13, Remove garments promptly
after cycle is finished
between the tub and the washer drum.
If you will be unable to remove the load promptly,
use the Fresh Hold "j or Fresh Spin TM option
(depending on model). If selected,
the Fresh Hold '°joption will activate the fan
and tumble the load periodically for up to
1 2 hours. The Fresh Spin TM option will tumble
the load periodically for up to 6 hours. To turn
off the Fresh Hold 1_or Fresh Spin TM option, touch
OR
m [l'eS_
[ 0'0-t
POWER/CANCEL To set the washer so that the Fresh Hold"_/
Fresh Spin TM option does not come on for future cycles, touch Fresh
Hold -_or Fresh Spin TM option.
NOTE:
III The door will remain locked while the Fresh Hold:_/Fresh Spin TM
option is active. To cancel the option and unlock the door, touch
POWER/CANCEL
[] A small amount of water may remain in the dispensers after the
wash cycle is complete. This is normal.
[] This washer has a tight seal to avoid water leaks. To avoid odors,
leave the door open to allow the washer to dry between uses.
12
WASHERMAINTENANCE
WATER iNLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
WASHER CARE
Recommendations to Help Keep Your Washer Clean
and Performing at its Best
1. Always use High Efficiency (HE) detergents and follow the
HE detergent manufacturer's instructions regarding the
amount of HE detergent to use, Never use more than the
recommended amount because that may increase the rate
at which detergent and soil residue accumulate inside your
washer, which in turn may result in undesirable odor,
2. Use warm or hot water washes sometimes (not exclusively
cold water washes), because they do a better job of controlling
the rate at which soils and detergent accumulate,
3. Always leave the washer door slightly ajar between uses
to help dry out the washer and avoid the buildup of
odor-causing residue,
4. Periodically clean residue from the underside of the glass
window,
Cleaning Your Front Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This Washer
Maintenance Procedure should be performed, at a minimum,
once per month or every 30 wash cycles, whichever occurs
sooner, to control the rate at which soils and detergent may
otherwise accumulate in your washer,
Cleaning the Door Seal
1. Open the washer door and remove any clothing or items from
the washer,
2. inspect the colored seal between the door opening and the
drum for stained areas or soil buildup. Pull back the seal
to inspect all areas under the seal and to check for foreign
objects,
3. if stained areas or soil buildup are found, wipe down these
areas of the seal using either of the following two procedures:
a. affresh :" Grit Grabber TM Cloth Procedure:
i, When the cycle is complete, gently pull back the rubber
door seal and clean the entire surface with the rough
side of the Grit Grabber TM cloth.
b. Dilute Liquid Chlorine Bleach Procedure:
i, Mix a dilute bleach solution, using 3/4 cup (177 mL) of
liquid chlorine bleach and 1 gallon (3,8 L) of warm tap
water,
ii, Wipe the seal area with the dilute solution, using
a damp cloth,
iii, Let stand 5 minutes,
iv, Wipe down area thoroughly with a dry cloth and let
washer interior air dry with door open,
IM PORTANT:
[] Wear rubber gloves when cleaning with bleach,
[] Refer to the bleach manufacturer's instructions for
proper use,
WASHER CARE (cont.)
Cleaning the Inside of the Washer
This washer has a special cycle that uses higher water volumes
in combination with affresh '_ Washer Cleaner or liquid chlorine
bleach to thoroughly clean the inside of the washer. Steam
washer models also utilize steam to enhance cleaning in this
special cycle,
NOTE: Read these instructions completely before beginning the
cleaning process,
Begin procedure
1. Clean Washer with affresh :" Cycle Procedure
(Recommended for Best Performance):
a. Open the washer door and remove any clothing or items,
b. Add an affresh '_ Washer Cleaner tablet to the washer
drum,
c. Do not add the affresh "_Washer Cleaner tablet to the
dispenser drawer,
d. Do not add any detergent or other chemical to the washer
when following this procedure,
e. Close the washer door,
f. Select the Clean Washer with affresh '_ cycle,
g. On some models: Select the Fresh Hold"_/Fresh Spin _
option to help dry the washer interior after the cycle is
complete, NOTE: The washer remembers your last option
selection and will use it for future wash cycles until you
deselect that option, While the fan is on, the washer door
will lock. To unlock the door, touch POWER/CANCEL.
h. Touch and hold START to begin the cycle, The Clean
Washer with affresh "_Cycle Operation is described below.
2. Chlorine Bleach Procedure:
a. Open the washer door and remove any clothing or items.
b. Open the dispenser drawer and add liquid chlorine bleach
to the MAX level in both the bleach compartment and
the fabric softener compartment. Either traditional or HE
chlorine bleach can be used,
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage over time,
c. Close the washer door and the dispenser drawer,
d. Do not add any detergent or other chemicals to the
washer when following this procedure,
e. Close the washer door,
f. Select the Clean Washer with affresh '_ cycle,
g. On some models: Select the Fresh Hold"_/Fresh Spin _
option to help dry the washer interior after the cycle is
complete, NOTE: The washer remembers your last option
selection and will use it for future wash cycles until you
deselect that option, While the fan is on, the washer door
will lock. To unlock the door, touch POWER/CANCEL.
h. Touch and hold START to begin the cycle, The Clean
Washer with affresh "_Cycle Operation is described below.
NOTE: For best results, do not interrupt cycle,
13
WASHERMAINTENANCE
WASHER CARE (cont.)
Description of Clean Washer with affresh _"Cycle Operation:
1. The Clean Washer with affresh "_cycle, will determine whether
clothing or other items are in the washer.
2. if no items are detected in the washer, it will proceed with
the cycle.
a. if any items are detected in the washer, "rL" (remove load)
will be displayed. The door will unlock. Open washer and
remove any garments from the washer drum,
b. Touch POWER/CANCEL to clear the "rL" code.
c. Touch and hold START to restart the cycle,
3. Steam models only: During the first 20 minutes of the cycle,
it will activate the steamer but the drum will not spin or fill
with water, You may see condensation on the door glass
during this initial phase, if you are using an affresh "_Washer
Cleaner tablet, it will not dissolve completely during the
steam phase, This is normal.
After the cycle is complete, leave the door open slightly to allow
for better ventilation and drying of the washer interior,
Cleaning the Dispensers
After a period of using your washer, you may find some residue
buildup in the washer's dispensers. To remove residue from the
dispensers, remove the drawer and wipe the surfaces with a
damp cloth and towel dry either before or after you run the Clean
Washer with affresh "_cycle, Use an aIFpurpose surface cleaner,
if needed,
iMPORTANT: Dispenser is not dishwasher safe,
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to help keep it
looking new, Use mild soap and water,
iMPORTANT: To avoid damaging the washer's finish, do not use
abrasive products,
CLEAN WASHER CYCLE REMINDER
NOTE: Not all models have the Clean Washer with affresh "_
cycle reminder light:
The Clean Washer with affresh "_ ___J ,_,
LED will flash at the end of a _ ";_<'ean washer
wash cycle when the washer has w_,_
run 30 wash cycles, This is a
reminder to run the Clean Washer with affresh '_ cycle,
If the Clean Washer with affresh "_cycle is not turned on, the LED
will stop flashing at the end of a wash cycle after running 3 more
regular wash cycles, After 30 more wash cycles are completed,
the Clean Washer with affresh '_ LED will again flash at the end
of a wash cycle as a reminder,
tf "_
REMOVING THE DISPENSER
To remove:
1. Pull dispenser drawer out until it stops,
2. Press down on the release tab and pull straight out to
remove the dispenser.
"\.",.,,
3. Lift off cover panel by
pulling straight up,
To replace:
1. Slide cover panel back
onto posts on dispenser,
2. Align edges of dispenser
with guides in washer,
then slide dispenser
back into slot.
14
NON-USE AN D VACATION CARE
Operate your washer only when you are home, If moving, or
not using your washer for a period of time, follow these steps:
1. Unplug or disconnect power to washer,
2. Turn off water supply to washer to avoid flooding due
to water pressure surges.
3. Clean dispensers, See "Cleaning the Dispensers"
tf "_
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze, Because some water may stay in
hoses, freezing can damage washer, If storing or moving
during freezing weather, winterize your washer,
To winterize washer:
1. Shut off both water faucets, disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in washer drum
and run washer on NORMAL cycle for about 2 minutes
to mix antifreeze and remaining water,
3. Unplug washer or disconnect power,
TRANSPORTING YOUR WASHER
1. Shut off both water faucets, Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain hose from drain system and from back
of washer,
4. Unplug power cord,
5. Place inlet hoses and drain hose inside washer drum,
6. Bundle power cord with a rubber band or cable tie to keep
it from hanging onto the ground,
IM PORTANT: Call for service to install new transport bolts,
Do not reuse transport bolts. Washer must be transported
in the upright position, To avoid structural damage to your
washer, it must be properly set up for relocation by a certified
technician,
f REINSTALLING/USING WASHER AGAIN "_
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer,
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet hoses.
Turn on both water faucets.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
2. Plug in washer or reconnect power.
3. Run washer through NORMAL cycle to clean washer and
remove antifreeze, if used. Use only HE detergent. Use half
the manufacturer's recommended amount for a medium-size
load,
15
TROUBLESHOOTING
First try the solutions suggested here or visit our webske at www.maytag.com/product_heJp -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
If you experience Possible Causes 1 Solution
Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.
"Sud" (Excess suds)
appears in display
Excessive suds in washer. Washer is
running a suds reduction routine.
Check for proper water supply.Fn8 followed by En/
(water supply error)
appears in display
Check plumbing for correct drain
hose installation. Drain hose extends into
standpipe farther than 41/2'' (114 mm).
Fn9 followed by En/
(drain pump system
error) appears in display
Not using HE detergent or using too
much HE detergent.
Fn5 followed by En2 Washer door not locking.
(door will not lock)
appears in display
"rL" (remove load) appears Load detected in drum during Clean
in display Washer with affresh "j cycle.
Washer making error beeps Door has not been opened and closed
for at least 3 cycles.
Washer beeps when START Door not closed.
is touched
Allow the washer to continue. Use only HE detergent. Always
measure detergent, and base detergent quantity on load size.
Follow detergent manufacturer's instructions.
Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears
again, call for service.
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor.
Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level.
Touch POWER/CANCEL to cancel the cycle. Make sure the
door is closed completely and latching. Check for items in
the washer drum that may be keeping the door from closing
completely.
Remove items from washer drum and restart Clean Washer with
affresh _-_cycle.
This code may appear when the washer is first turned on.
Open and close the door to clear the display.
Close the door completely.
F## E## code other than System error code. Touch POWER/CANCEL once to clear the code. Then touch
as described above appears POWER/CANCEL again to restart washer. If code appears
in display again, call for service.
"lnt" (interrupted) appears in The cycle was paused or cancelled. The washer can take 20 to 30 minutes to stop spinning
display and drain and will display this error code during that time.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer.
Clean Washer LED flashing
at end of wash cycle
The washer has run 30 wash cycles and
is indicating a reminder to run the Clean
Washer with affresh "j cycle.
Run the Clean Washer with affresh "_cycle. If the Clean Washer
with affresh "_cycle is not turned on, the LED will stop flashing
at the end of a wash cycle after running 3 more regular wash
cycles. After 30 more wash cycles are completed, the Clean
Washer LED will again flash at the end of a wash cycle as a
reminder.
.J
16
TROUBLESHOOTING
f
if you experience
First try the solutions suggested here or visit our website at www.maytag.com/producLhelp -
in Canada www.maytag.ca for assistance and to possibly avoid a service call.
Possible Causes Solution
Vibration, rocking, or Feet may not be in contact with the floor
"walking" and locked.
Washer may not be level.
Load could be unbalanced or too large.
The shipping bolts are still in the back of
the washer.
Clicking or metallic noises Door locking or unlocking.
Objects caught in washer drain system.
Front and rear feet must be in firm contact with floor, and washer
must be level to operate properly. Jam nuts must be tight against
the bottom of the cabinet.
Check floor for flexing or sagging, if flooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See "Level the Washer" in installation instructions.
Avoid tightly packing the load. Avoid washing single items.
Balance a single item such as a rug or jeans jacket with a few
extra items.
item or load not suitable for selected cycle. See "Cycle Guide"
and "Using Your WasherS'
See "Remove transport bolts from washer" in the installation
Instructions.
Gurgling or humming
Rolling or sloshing
and occasional clicking
(on low-speed spin)
Washer may be draining water.
Steel balls in the balancing system are
balancing the load.
The door will lock, unlock, and lock again. You will hear 3 clicks
after touching and holding START. This is normal.
Empty pockets before washing. Loose items such as coins could
fall between washer drum and tub or may block pump. it may be
necessary to call for service to remove items.
it is normal to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel drum.
The pump may make a humming sound with periodic gurgling or
surging as final amounts of water are removed during the spin/
drain cycles. This is normal at certain stages of the cycle.
This is normal at certain stages of the cycle.
Check the following for
proper installation
Water or suds leaking from
door or rear of cabinet
Load not completely
covered in water
k.
Fill hoses not attached tightly.
Fill hose washers.
Drain hose connection.
Check household plumbing for leaks or
clogged sink or drain.
Not using HE detergent or using too
much HE detergent.
Residue on door glass.
Door opened during "Add a Garment_'
Water level not visible on door or does
not cover clothes.
Tighten _Fhose connection.
Properly seat ail four _Fhose flat washers.
Check that the drain hose is properly secured to drainpipe or
laundry tub.
Water can back up out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe, water
pipes, and faucets.)
Only use HE detergent. Suds from regular detergents can
cause leaking from the door or rear of cabinet. Always measure
detergent and follow manufacturer's directions based on your
load requirements.
Periodically clean the underside of the glass window to avoid
potential leaks.
Water can drip off the inside of the door when the door is
opened after the start of a cycle.
This is normal for an HE front load washer. The washer senses
load sizes and adds the correct amount of water for optimal
cleaning.
J
17
TROUBLESHOOTING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
in Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience Possible Causes J Solution
Washer won't run or fill,
washer stops working
Check for proper water supply. Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water flow.
Check proper electrical supply. Plug power cord into a grounded 3-prong outlet.
Do not use an extension cord.
Ensure there is power to outlet.
Check electrical source or call an electrician to check if voltage is low.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: if problems continue, contact an electrician.
Normal washer operation. Door must be completely closed and latched for washer to run.
Washer will pause during certain phases of cycle. Do not interrupt cycle.
The washer pauses for about 2 minutes during certain cycles. Allow the
cycle to continue. Some cycles feature periods of tumbling and soak.
Washer may be stopped to reduce suds.
Cold Wash uses less water in the beginning of the cycle to provide a
high concentration of detergent for optimal cleaning action. Following this
concentrated tumbling, more water is used to complete the wash.
Steam Models only: During the first 20 minutes of the Clean Washer
with affresh 'Rjcycle, it will activate the steamer but the drum will not spin
or fill with water. You may see condensation on the door glass during this
initial phase, if you are using an affresh '-_Washer Cleaner tablet, it will not
dissolve completely during the steam phase. This is normal.
The washer door is not firmly shut. The door must be closed during operation.
Washer not loaded as Remove several items, rearrange load evenly in washer drum. Close door
recommended, and touch and hold START.
Do not add more than 1 or 2 additional items after cycle has started to
avoid tightly packing or unbalancing.
Do not add more water to the washer.
J
18
TROUBLESHOOTING
Washer won't run or fill,
washer stops working
(cont.)
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience Possible Causes l Solution
Not using HE detergent or using too Only use HE detergent. Suds from regular detergents can
much HE detergent, slow or stop the washer. Always measure detergent, following
Door not opened between cycles.
Washer not draining/ Drain hose extends into standpipe farther
spinning, loads are than 4.5" (114 mm).
still wet
The drain hose is clogged, or the end
of the drain hose more than 96" (2.4 m)
above the floor.
The drain hose fits too tightly in the
standpipe, or is it taped to the standpipe.
Using cycles with a lower spin speed.
Washer not loaded as recommended.
The load may be out of balance.
Not using HE detergent or using too
much HE detergent.
Small items may have been caught in the
pump or stuck between the washer drum
and the outer tub.
There are too many clothes in the Wash
& Dry cycle.
Door locked at end of wash Water remaining in washer after cycle.
cycle.
Fresh Hold-_/Fresh Spin TM option is on.
Door will not unlock Door locks when cycle has started.
Check for proper water supply.Incorrect or wrong wash or
rinse temperatures
Washing many loads.
manufacturer's directions based on your load requirements.
To remove suds, cancel cycle. Select DRAIN & SPIN with Extra
Rinse. Touch and hold START. Do not add more detergent.
After 3 wash cycles in a row are completed, the door must be
opened and then closed before a new cycle can begin.
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor. Remove any clogs from drain hose. See "Installation
Requirements" in Installation Instructions.
The drain hose should be loose yet fit securely. Do not seal the
drain hose with tape. The hose needs an air gap. See "Secure
the Drain Hose" in Installation Instructions.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment.
A tightly packed or unbalanced load may not allow the washer
to spin correctly, leaving the load wetter than normal. See "Cycle
Guide" for load size recommendation for each cycle.
Avoid washing single items. Balance a single item such as a rug
or jeans jacket with a few extra items.
Use only HE detergent. Suds from regular detergent or using
too much detergent can slow or stop draining or spinning.
Always measure and follow manufacturer's directions for your
load. To remove extra suds, select DRAIN & SPIN with Extra
Rinse. Do not add detergent.
Check the drum for any items sticking through the drum holes.
Empty pockets and use garment bags when washing small items.
Only use the Overnight Wash & Dry cycle for 2-4 lightly soiled
synthetic garments, athletic uniforms, or workout wear.
Select DRAIN & SPIN to remove any water remaining in the
washer. The washer door will unlock at the end of the drain.
While this option is on, the fan blows (Fresh Hold -_option only)
and the load is tumbled periodically for up to 12 hours (Fresh
Hold -_option) or 6 hours (Fresh Spin TM option). The door remains
locked during this time. To unlock the door, cancel the option by
touching POWER/CANCEL
If the "Add a Garment" light is lit, touch START once. The door
will unlock.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and
have both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Your hot water tank may not have enough hot water to keep up
with the number of hot or warm washes. This is normal.
19
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
in Canada www.maytag.ca for assistance and to possibly avoid a service call.
if you experience l Possible Causes _ Solution
Desired setting or
option does not light
Load not rinsed
For best performance, not all settings
are available with each cycle, and some
options cannot be used together.
Load is wrinkled, twisted,
or tangled
Check for proper water supply.
Not using HE detergent or using too
much HE detergent.
Washer not loaded as recommended.
The load may be out of balance.
Washer not loaded as recommended.
Wash action too long for load.
Spin speed too high for load.
The washer is not unloaded promptly.
Not choosing the right cycle for the load
being washed.
The wash water was not warm enough
to relax wrinkles.
Washer not loaded as recommended.
Not using HE detergent or using too
much HE detergent.
Hard water or high level of iron (rust) in
water.
Fabric softener dispensing ball used.
Powdered detergent used for
low-speed cycle.
Not cleaning or removing
stains
See the "Cycle Guide" for the available settings and options for
each cycle.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can cause the washer
to operate incorrectly.
Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level.
Avoid tightly packing the washer. The washer will not rinse well
if tightly packed. Load with dry items only. See the "Cycle Guide"
for load size recommendations for each cycle.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started.
When load unbalance occurs, a washing process will start to
redistribute the load. This may lengthen the cycle time. Avoid
washing single items. Balance a single item such as a rug or
jeans jacket with a few extra items.
Add load loosely. Items need to move freely reduce wrinkling and
tangling. See the "Cycle Guide" for load size recommendations
for each cycle.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Select a lower soil level. Note that items will not be cleaned as
deeply as when using a higher soil level.
Select a lower spin speed. Note that items will be wetter than
when using a higher speed spin.
Unload the washer as soon as it stops or use Fresh Hold'RJ/Fresh
Spin TM option if you will not be able to unload the washer at the
end of the cycle.
Use the Delicates cycle or another cycle with a low spin speed
to reduce wrinkling.
If safe for load, use warm or hot wash water.
Add load loosely. Items need to move freely for best cleaning.
See the "Cycle Guide" for load size recommendations for each
cycle.
Add only 1 or 2 garments after washer has started.
Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level.
You may need to install a water softener and/or iron filter.
Dispensing balls will not operate correctly with this washer.
Add liquid fabric softener to the fabric softener compartment.
Consider using liquid detergent.
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52

Maytag MHW5400D Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

dans d''autres langues