Sony DSC-H70 Mode d'emploi

4-272-192-31(1)

DSC-H70

Digital Still Camera / Instruction Manual GB

Appareil photo numérique / Mode d’emploi FR

GB

2

Owner’s Record

The model and serial numbers are located on the bottom. Record the serial number in the

space provided below. Refer to these numbers whenever you call your Sony dealer

regarding this product.

Model No. DSC-H70

Serial No. ______________________________

To reduce fire or shock hazard, do not expose the unit to rain or

moisture.

IMPORTANT SAFETY INSTRUCTIONS

-SAVE THESE INSTRUCTIONS

DANGER

TO REDUCE THE RISK OF FIRE OR ELECTRIC

SHOCK, CAREFULLY FOLLOW THESE

INSTRUCTIONS

If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the

proper configuration for the power outlet.

[ Battery pack

If the battery pack is mishandled, the battery pack can burst, cause a fire or even chemical

burns. Observe the following cautions.

• Do not disassemble.

• Do not crush and do not expose the battery pack to any shock or force such as

hammering, dropping or stepping on it.

• Do not short circuit and do not allow metal objects to come into contact with the battery

terminals.

• Do not expose to high temperature above 60°C (140°F) such as in direct sunlight or in a

car parked in the sun.

• Do not incinerate or dispose of in fire.

• Do not handle damaged or leaking lithium ion batteries.

English

WARNING

CAUTION

GB

3

GB

• Be sure to charge the battery pack using a genuine Sony battery charger or a device that

can charge the battery pack.

• Keep the battery pack out of the reach of small children.

• Keep the battery pack dry.

• Replace only with the same or equivalent type recommended by Sony.

• Dispose of used battery packs promptly as described in the instructions.

[ Battery charger

Even if the CHARGE lamp is not lit, the battery charger is not disconnected from the AC

power source (mains) as long as it is connected to the wall outlet (wall socket). If some

trouble occurs while using the battery charger, immediately shut off the power by

disconnecting the plug from the wall outlet (wall socket).

The power cord (mains lead), if supplied, is designed specifically for use with this camera

only, and should not be used with other electrical equipment.

[ RECYCLING LITHIUM-ION BATTERIES

Lithium-Ion batteries are recyclable.

You can help preserve our environment by returning your used

rechargeable batteries to the collection and recycling location nearest

you.

For more information regarding recycling of rechargeable batteries,

call toll free

1-800-822-8837, or visit http://www.rbrc.org/

Caution: Do not handle damaged or leaking Lithium-Ion batteries.

[ Battery pack

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

For Customers in the U.S.A. and Canada

GB

4

UL is an internationally recognized safety organization.

The UL Mark on the product means it has been UL Listed.

If you have any questions about this product, you may call:

Sony Customer Information Center

1-800-222-SONY (7669).

The number below is for the FCC related matters only.

[ Regulatory Information

[ CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual

could void your authority to operate this equipment.

[ Note:

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The supplied interface cable must be used with the equipment in order to comply with the

limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

For Customers in the U.S.A.

Declaration of Conformity

Trade Name: SONY

Model No.: DSC-H70

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo,

San Diego, CA 92127 U.S.A.

Telephone No.: 858-942-2230

This device complies with Part15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may cause

undesired operation.

GB

5

GB

[ Notice for the customers in the countries applying EU Directives

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo,

108-0075 Japan. The Authorized Representative for EMC and product safety is Sony

Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or

guarantee matters please refer to the addresses given in separate service or guarantee

documents.

This product has been tested and found compliant with the limits set out in the EMC

Directive for using connection cables shorter than 3 meters (9.8 feet).

[ Attention

The electromagnetic fields at the specific frequencies may influence the picture and sound

of this unit.

[ Notice

If static electricity or electromagnetism causes data transfer to discontinue midway (fail),

restart the application or disconnect and connect the communication cable (USB, etc.)

again.

[ Disposal of Old Electrical & Electronic Equipment (Applicable in

the European Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product

shall not be treated as household waste. Instead it shall be handed over to

the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help

prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling

of this product. The recycling of materials will help to conserve natural

resources. For more detailed information about recycling of this product,

please contact your local Civic Office, your household waste disposal service or the shop

where you purchased the product.

For Customers in Europe

GB

6

[ Disposal of waste batteries (applicable in the European Union

and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery

provided with this product shall not be treated as household waste.

On certain batteries this symbol might be used in combination with a

chemical symbol. The chemical symbols for mercury (Hg) or lead (Pb) are

added if the battery contains more than 0.0005% mercury or 0.004% lead.

By ensuring these batteries are disposed of correctly, you will help prevent

potentially negative consequences for the environment and human health which could

otherwise be caused by inappropriate waste handling of the battery. The recycling of the

materials will help to conserve natural resources.

In case of products that for safety, performance or data integrity reasons require a

permanent connection with an incorporated battery, this battery should be replaced by

qualified service staff only. To ensure that the battery will be treated properly, hand over

the product at end-of-life to the applicable collection point for the recycling of electrical

and electronic equipment.

For all other batteries, please view the section on how to remove the battery from the

product safely.

Hand the battery over to the applicable collection point for the recycling of waste batteries.

For more detailed information about recycling of this product or battery, please contact

your local Civic Office, your household waste disposal service or the shop where you

purchased the product.

A moulded plug complying with BS 1363 is fitted to this equipment for your safety and

convenience.

Should the fuse in the plug supplied need to be replaced, a fuse of the same rating as the

supplied one and approved by ASTA or BSI to BS 1362, (i.e., marked with an or

mark) must be used.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the

fuse cover after you change the fuse. Never use the plug without the fuse cover. If you

should lose the fuse cover, please contact your nearest Sony service station.

Notice for customers in the United Kingdom

GB

7

GB

For details on advanced operations, please read “Cyber-shot User Guide”

(HTML) on the CD-ROM (supplied) using a computer.

For Windows users:

1 Click [User Guide] t [Install].

2 Start “User Guide” from the shortcut on the desktop.

For Macintosh users:

1 Select the [User Guide] and copy [eng] folder stored in [User Guide] folder

to your computer.

2 After copying is complete, double-click “index.html” in [eng] folder.

• Battery charger BC-CSGD (1)

• Power cord (mains lead) (not supplied in the USA and Canada) (1)

• Rechargeable battery pack NP-BG1 (1)/Battery case (1)

• USB, A/V cable for multi-use terminal (1)

• Wrist strap (1)

•CD-ROM (1)

– Cyber-shot application software

– “Cyber-shot User Guide”

• Instruction Manual (this manual) (1)

Refer to “Cyber-shot User Guide” (HTML) on

supplied CD-ROM

Checking the accessories supplied

Insert the CD-ROM into the CD-ROM drive.

GB

8

A Shutter button

B Mode dial

C For shooting: W/T (zoom) lever

For viewing: (Playback

zoom) lever/ (Index) lever

D Flash

E ON/OFF (Power) button/Power

lamp

F Microphone

G Self-timer lamp/Smile Shutter

lamp/AF illuminator

H Lens

I (TransferJet™) mark

J LCD screen

K (Playback) button

L Hook for wrist strap

M / (In-Camera Guide/Delete)

button

N MENU button

O Control button

Menu on: v/V/b/B/z

Menu off: DISP/ / / /

Tracking focus

P Speaker

Q Tripod receptacle

• Use a tripod with a screw less

than 5.5 mm (7/32 inches) long.

Otherwise, you cannot firmly

secure the camera, and damage to

the camera may occur.

R Multi connector (Type3a)

S Battery/Memory card cover

T Battery insertion slot

U Battery eject lever

V Memory card slot

W Access lamp

Identifying parts

GB

9

GB

x

Charging time

Full charge time: approx. 330 min.

Normal charge time: approx. 270 min.

• The above charging times apply when charging a fully depleted battery pack at a

temperature of 25°C (77°F). Charging may take longer depending on conditions of

use and circumstances.

• Connect the battery charger to the nearest wall outlet (wall socket).

• When charging is finished, disconnect the power cord (mains lead) from the wall

outlet (wall socket), and remove the battery pack from the battery charger.

• Be sure to use the battery pack or the battery charger of the genuine Sony brand.

Charging the battery pack

1

Insert the battery pack into the battery charger.

• You can charge the battery even when it is partially charged.

2

Connect the battery charger to the wall outlet (wall

socket).

• If you continue charging the battery pack for about one more hour after

the CHARGE lamp turns off, the charge will last slightly longer (full

charge).

Notes

Plug

For customers in the USA

and Canada

CHARGE lamp

Power cord

(Mains lead)

For customers in countries/regions

other than the USA and Canada

Lit: Charging

Off: Charging finished (normal charge)

GB

10

x

Battery life and number of images you can record/

view

• The number of images that can be recorded is an approximate number when

shooting with a fully charged battery pack. The number may be less depending on

the circumstances.

• The number of images that can be recorded is when shooting under the following

conditions:

– Using Sony “Memory Stick PRO Duo” (Mark2) media (sold separately).

– When a fully charged battery pack (supplied) is used at an ambient temperature

of 25°C (77°F).

• The number of still images that can be recorded is based on the CIPA standard,

and is for shooting under the following conditions.

(CIPA: Camera & Imaging Products Association)

– DISP (Screen Display Settings) is set to [Normal].

– Shooting once every 30 seconds.

– The zoom is switched alternately between the W and T ends.

– The flash strobes once every two times.

– The power turns on and off once every ten times.

• The battery life for movies is when shooting under the following conditions:

– Recording mode: 720 FINE

– When continuous shooting ends because of set limits (page 19), press the shutter

button down again and continue shooting. Shooting functions such as the zoom

do not operate.

Battery life (min.) Number of images

Shooting still images Approx. 145 Approx. 290

Viewing still images Approx. 410 Approx. 8200

Shooting movies Approx. 150 —

Notes

GB

11

GB

x

Memory cards that you can use

• In this manual, products in A are collectively referred to as “Memory Stick Duo”

media.

• In this manual, products in B are collectively referred to as SD card.

• When recording movies, it is recommended that you use Mark2 “Memory Stick

Duo” media and Class 4 or faster SD cards.

Inserting the battery pack/a memory card (sold

separately)

1

Open the cover.

2

Insert the memory card (sold separately).

• With the notched corner facing as illustrated, insert the memory card

until it clicks into place.

3

Insert the battery pack.

• While pressing the battery eject lever, insert the battery pack as

illustrated. Make sure that the battery eject lever locks after insertion.

4

Close the cover.

• Closing the cover with the battery inserted incorrectly may damage the

camera.

Memory card For still images For movies

A

Memory Stick PRO Duo aa

Memory Stick PRO-HG Duo aa

Memory Stick Duo a —

B

SD memory card aa

SDHC memory card aa

SDXC memory card aa

Ensure the notched corner faces correctly.

GB

12

x

To remove the memory card/battery pack

Memory card: Push the memory card in once.

Battery pack: Slide the battery eject lever. Be sure not to drop the battery pack.

• Never remove the memory card/battery pack when the access lamp (page 8) is lit.

This may cause damage to data in the memory card/internal memory.

Note

Setting the clock

1

Press the ON/OFF (Power) button.

Date & Time setting is displayed when you press the ON/OFF (Power)

button for the first time.

• It may take time for the power to turn on and allow operation.

2

Set [Date & Time Format], [Daylight Savings] and [Date

& Time], then press [OK].

• Midnight is indicated as 12:00 AM, and noon as 12:00 PM.

3

Select the desired area following the instructions on the

screen, then press z t [OK].

4

Select the desired display color and display resolution

mode, following the instructions on the screen.

5

When an [In-Camera Guide] introductory message is

appeared on the screen, press [OK].

Select items: v/V/b/B

Set: z

Control button

ON/OFF (Power)

GB

13

GB

Shooting still images

Shooting movies

• The operating sound of the lens is recorded when the zoom function operates

while shooting a movie.

• You can shoot continuously for approximately 29 minutes at a time when the

temperature is 25°C (77°F) and camera is set to the factory settings. When

shooting stops, you can press the shutter button again to restart shooting.

Depending on the temperature when shooting, recording may automatically stop

to protect the camera (page 21).

Shooting still images/movies

1

Press the shutter button halfway down to focus.

When the image is in focus, a beep sounds and the z indicator lights.

2

Press the shutter button fully down.

1

Press the shutter button fully down to start recording.

• Use the W/T (zoom) lever to change the zoom scale.

2

Press the shutter button fully down again to stop

recording.

Notes

Mode dial

Shutter button

W: zoom out

T: zoom in

: Still image

: Movie

GB

14

x

Selecting next/previous image

Select an image with B (next)/b (previous) on the control button. Press z in

the center of the control button to view movies.

x

Deleting an image

1 Press / (Delete) button.

2 Select [This Image] with v on the control button, then press z.

x

Returning to shooting images

Press the shutter button halfway down.

Viewing images

1

Press the (Playback) button.

• When images on a memory card recorded with other cameras are played

back on this camera, the registration screen for the data file appears.

/ (Delete)

Control button

(Playback)

W: zoom out

T: zoom in

Select images: B (next)/b (previous)

Set: z

GB

15

GB

This camera contains an internal function guide. This allows you to search the

camera’s functions according to your needs.

In-Camera Guide

1

Press the / (In-Camera Guide) button.

• When viewing images, [Delete/In-Camera Guide] is displayed. Select

[In-Camera Guide].

2

Select a search method from [In-Camera Guide].

Shoot/playback guide: Search for various operation functions in

shooting/viewing mode.

Icon guide: Search the function and meaning of displayed icons.

Troubleshooting: Search common problems and their solution.

Objective guide: Search functions according to your needs.

Keyword: Search functions by key words.

History: Display the last 12 items displayed in [In-Camera Guide].

/

(In-Camera Guide)

GB

16

Other functions used when shooting or playing back can be operated using the

Control button or MENU button on the camera. This camera is equipped with

a Function Guide that allows you to easily select from the functions. While

displaying the guide, try the other functions.

x

Control button

DISP (Screen Display Settings): Allows you to change the screen display.

(Self-Timer): Allows you to use the self-timer.

(Smile Shutter): Allows you to use the Smile Shutter mode.

(Flash): Allows you to select a flash mode for still images.

x

Menu Items

Shooting

Introduction of other functions

Scene Selection Select pre-set settings to match various scene conditions.

Easy Mode Shoot still images using minimal functions.

Shooting Direction

Set the direction to pan the camera when shooting Sweep

Panorama images.

Image Size/

Panorama Image

Size

Select the image size for still images, panoramic images

or movie files.

Burst Settings Select single-image mode or burst mode.

Bracket Setting Set the type of the bracket shooting.

EV Adjust the exposure manually.

ISO Adjust the luminous sensitivity.

MENU

Control

button

Function Guide

GB

17

GB

Viewing

White Balance Adjust color tones of an image.

Focus Select the focus method.

Metering Mode

Select the metering mode that sets which part of the

subject to measure to determine the exposure.

Scene Recognition

Set to automatically detect shooting conditions in

Intelligent Auto mode.

Soft Skin Effect Set the Soft Skin Effect and the effect level.

Smile Detection

Sensitivity

Set the Smile Shutter function sensitivity for detecting

smiles.

Face Detection

Select to detect faces and adjust various settings

automatically.

DRO

Set DRO function to correct the brightness and contrast

and improve the image quality.

Anti Blink

Set to automatically shoot two images and select image

in which the eyes are not blinking.

SteadyShot Set the strength of SteadyShot in Movie Mode.

In-Camera Guide Search the camera’s functions according to your needs.

Slideshow Select a method of continuous playback.

Send by

TransferJet

Sends images from a Memory Stick with TransferJet to

TransferJet-compatible devices.

View Mode Select the display format for images.

Retouch Retouch an image using various effects.

Delete Delete an image.

Protect Protect the images.

DPOF Add a print order mark to a still image.

Rotate Rotate a still image to the left or right.

Select Folder

Select a folder which contains the images you want to

play back.

In-Camera Guide Search the camera’s functions according to your needs.

GB

18

x

Setting items

If you press the MENU button while shooting or during playback,

(Settings) is provided as a final selection. You can change the default

settings on the (Settings) screen.

* If a memory card is not inserted, (Internal Memory Tool) will be displayed and

only [Format] and [File Number] can be selected.

The number of still images and recordable time may vary depending on the

shooting conditions and the memory card.

x

Still images

(Units: Images)

Shooting Settings

AF Illuminator/Grid Line/Disp. Resolution/Digital

Zoom/Auto Orientation/Red Eye Reduction/Blink Alert

Main Settings

Beep/Language Setting/Function Guide/Display color/

Demo Mode/Initialize/COMPONENT/Video Out/USB

Connect/LUN Setting/Download Music/Empty Music/

Power Save/TransferJet/Eye-Fi

Memory Card Tool

*

Format/Create REC. Folder/Change REC. Folder/Delete

REC. Folder/Copy/File Number

Clock Settings

Area Setting/Date & Time Setting

Number of still images and recordable time of

movies

Capacity

Size

Internal memory Memory card

Approx. 27 MB 2 GB

16M 3 265

VGA 165 11500

16:9(12M) 4 325

GB

19

GB

x

Movies

The table below shows the approximate maximum recording times. These are

the total times for all movie files. Continuous shooting is possible for

approximately 29 minutes. The maximum size of a movie file is up to

approximately 2 GB.

(h (hour), m (minute), s (second))

The number in ( ) is the minimum recordable time.

• The recordable time of movies varies because the camera is equipped with VBR

(Variable Bit Rate), which automatically adjusts image quality depending on the

shooting scene. When you record a fast-moving subject, the image is clearer but

the recordable time is shorter because more memory is required for recording. The

recordable time also varies depending on the shooting conditions, the subject or

the image size settings.

Changing the language setting

To change the language setting, press MENU t (Settings) t (Main

Settings) t [Language Setting].

On use and care

Avoid rough handling, disassembling, modifying, physical shock, or impact

such as hammering, dropping or stepping on the product. Be particularly

careful of the lens.

Functions built into this camera

This manual describes each of the functions of TransferJet-compatible/

incompatible devices.

To check if your camera supports the TransferJet function, check for the

following mark on the bottom of the camera.

TransferJet-compatible device: (TransferJet)

Capacity

Size

Internal memory Memory card

Approx. 27 MB 2 GB

1280×720(Fine) — 25 m

(20 m)

1280×720(Standard) — 40 m

(25 m)

VGA 1 m

(45 s)

1h20m

(1 h)

Notes on using the camera

GB

20

Notes on recording/playback

• Before you start recording, make a trial recording to make sure that the

camera is working correctly.

• The camera is neither dust-proof, nor splash-proof, nor water-proof.

• Avoid exposing the camera to water. If water enters inside the camera, a

malfunction may occur. In some cases, the camera cannot be repaired.

• Do not aim the camera at the sun or other bright light. It may cause the

malfunction of the camera.

• If moisture condensation occurs, remove it before using the camera.

• Do not shake or strike the camera. It may cause a malfunction and you may

not be able to record images. Furthermore, the recording media may become

unusable or image data may be damaged.

Do not use/store the camera in the following places

• In an extremely hot, cold or humid place

In places such as in a car parked in the sun, the camera body may become

deformed and this may cause a malfunction.

• Under direct sunlight or near a heater

The camera body may become discolored or deformed, and this may cause a

malfunction.

• In a location subject to rocking vibration

• Near a location that generates strong radio waves, emits radiation or is

strongly magnetic place. Otherwise, the camera may not properly record or

play back images.

• In sandy or dusty places

Be careful not to let sand or dust get into the camera. This may cause the

camera to malfunction, and in some cases this malfunction cannot be repaired.

On carrying

Do not sit down in a chair or other place with the camera in the back pocket of

your trousers or skirt, as this may cause malfunction or damage the camera.

Notes on the LCD screen and lens

The LCD screen is manufactured using extremely high-precision technology

so over 99.99% of the pixels are operational for effective use. However, some

tiny black and/or bright dots (white, red, blue or green) may appear on the

LCD screen. These dots are a normal result of the manufacturing process, and

do not affect the recording.

Grip

If dark materials or leather rub against the grip, in some cases the color of the

grip may change.

La page charge ...

Sony DSC-H70 Mode d'emploi

Sony DSC-H70 Mode d'emploi

dans d''autres langues

Documents connexes