Yamaha EMX5 spécification

EMX5
Yamaha
Marque
Yamaha
Modèle
EMX5
Catégorie
Mélangeurs audio
Taper
spécification

Ce manuel convient également à

1
General Specifications
0 dBu = 0.775 Vrms, Output impedance of signal generator (Rs) = 150 Ω
All level controls are at their maximum position if not specified.
*1 THD+N is measured with 22 kHz LPF
*2 Noise is measured with A-weighting filter.
*3 Crosstalk is measured with 1 kHz band pass filter.
The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download
the manual file.
Output Power
1 kHz THD+N < 10%
(CEA2006)
630 W + 630 W (4 Ω)
460 W + 460 W (8 Ω)
1 kHz THD+N < 1%
(CEA2006)
500 W + 500 W (4 Ω)
370 W + 370 W (8 Ω)
Input to SPEAKERS
Input to STEREO OUT, AUX1 SEND, AUX2 SEND
Frequency Response
Refer to the nominal
output level @ 1 kHz
+1 dB/-3 dB (40 Hz to 20 kHz) +0.5 dB/-1 dB (20 Hz to 20 kHz)
Total Harmonic
Distortion
*1
(THD+N)
MIC/LINE =
LINE (CH1–4)
0.1% @ 10 W (40 Hz to 20 kHz)
0.05% @ 50 W (1 kHz)
0.03% @ +14 dBu (20 Hz to 20 kHz)
0.007% @ +20 dBu (1 kHz)
Hum & Noise
*2
(20 Hz to 20 kHz)
Equivalent Input Noise -117 dBu
Residual Output Noise
-70 dBu (40 Hz to 20 kHz, STEREO MASTER
LEVEL: min)
-82 dBu (20 Hz to 20 kHz, STEREO MASTER
LEVEL: min)
Crosstalk (1 kHz)
*3
-85 dB
Input channels TOTAL: 12 channels Mono (MIC/LINE): 8, Stereo (LINE): 4
Output channels SPEAKERS [A, B], AUX1 SEND, AUX2 SEND, STEREO OUT [L, R], REC OUT [L, R]
Bus Stereo: 1, AUX: 2 (Including FX)
Input Channel
Function
MIC/LINE (CH1–4) 30 dB PAD
Hi-Z (CH4) Supported
HPF (CH1–3) 80 Hz, -12 dB/oct.
Equalizer (EQ)
HIGH: 10 kHz +15 dB / -15 dB (Shelving)
MID: 2.5 kHz +15 dB / -15 dB (Peaking)
LOW: 100 Hz +15 dB / -15 dB (Shelving)
COMP (CH1–4) 1-knob COMP
Level Meter 2 × 7 points LED meter (-20, -10, -6, 0, +6, +10, PEAK)
Built-in Effect SPX Algorithm 24 programs
Output Channel Function Feedback suppressor, Master EQ, Monitor EQ
Phantom Power Voltage +48 V
FOOT SW Effect mute on/off
Protection
Load Protection: DC-fault
Amplifier Protection: Over heat protection, Over current protection, Integral power protection
Power Supply Protection: Over heat protection, Over current protection
Power Requirements AC 100-240 V, 50 Hz/60 Hz
Power Consumption 42 W (Idle) / 210 W (1/8 Power)
Dimensions (W × H × D) 465 mm × 308 mm × 325 mm (18.3" × 12.1" × 12.8")
Net Weight 9.5 kg (20.9 lb)
Included Accessory AC Power Cord (2.5 m), Owner’s Manual, Technical Specifications
Optional Accessory Rack-mount brackets: RK-EMX7, Foot switch: FC5
Operating Temperature 0 to +40°C
Analog Input Characteristics
0 dBu = 0.775 Vrms
*1 Sensitivity is the lowest level that will produce an output of +4 dBu (1.228 V) or the nominal output level when the unit is set to maximum gain.
(All level controls are at their maximum position.)
*2 Level controls setting : Channel level controls are at their t position. Master level controls are at their maximum position.
*3 1&Sleeve = GND, 2&Tip = HOT, 3&Ring = COLD
*4 Tip = Signal, Sleeve = GND
*5 1 = GND, 2 = HOT, 3 = COLD
*6 Tip = LEFT, Ring = RIGHT, Sleeve = GND
Analog Output Characteristics
0 dBu = 0.775 Vrms
0 dBV = 1.00 Vrms
*1 Tip = HOT, Ring = COLD, Sleeve = GND
Speaker Output Characteristics
*1 1+ = Positive, 1- = Negative
*2 Tip = Positive, Sleeve = Negative
Input Jack MIC/LINE Hi-Z
Actual Load
Impedance
For Use
with
Nominal
Input Level
Connector
Sensitivity
*1
Nominal Level
(t Position)
*2
Max.
Before Clip
CH 1–4
XLR
MIC —
3 kΩ
50–600 Ω
Mics
-60 dBu
(0.775 mV)
-43 dBu
(5.48 mV)
-15 dBu
(138 mV)
Combo jack
*3
(Balanced)
LINE —
-30 dBu
(24.5 mV)
-13 dBu
(173 mV)
+15 dBu
(4.36 V)
Phone
MIC —
8 kΩ
600 Ω
Lines
-50 dBu
(2.45 mV)
-33 dBu
(17.3 mV)
-5 dBu
(436 mV)
LINE —
-20 dBu
(77.5 mV)
-3 dBu
(548 mV)
+25 dBu
(13.8 V)
CH 4 (Hi-Z) Phone
MIC
ON 1 MΩ
10 kΩ
Lines
-50 dBu
(2.45 mV)
-33 dBu
(17.3 mV)
-5 dBu
(436 mV)
Phone jack
*4
(Unbalanced)
LINE
-20 dBu
(77.5 mV)
-3 dBu
(548 mV)
+20 dBu
(7.75 V)
CH 5/6, 7/8
XLR
——
3 kΩ
50–600 Ω
Mics
-60 dBu
(0.775 mV)
-43 dBu
(5.48 mV)
-15 dBu
(138 mV)
XLR-3-31
*5
(Balanced)
Phone 10 kΩ 600 Ω Lines
-20 dBu
(77.5 mV)
-3 dBu
(548 mV)
+25 dBu
(13.8 V)
Phone jack
*4
(Unbalanced)
CH 9/10, 11/12
XLR
——
3 kΩ
50–600 Ω
Mics
-60 dBu
(0.775 mV)
-43 dBu
(5.48 mV)
-15 dBu
(138 mV)
XLR-3-31
*5
(Balanced)
Pin 10 kΩ 600 Ω Lines
-8 dBu
(316 mV)
+10 dBu
(2.45 V)
+25 dBu
(13.8 V)
RCA pin
(Unbalanced)
CH 11/12
Mini
jack
— — 10 kΩ 600 Ω Lines
-8 dBu
(316 mV)
+10 dBu
(2.45 V)
+25 dBu
(13.8 V)
Stereo mini jack
*6
(Unbalanced)
Output Jack
Actual Source
Impedance
For Use with Nominal
Output level
Connector
Nominal Max. Before Clip
STEREO OUT L, R 600 Ω 10 kΩ Lines
+4 dBu
(1.228 V)
+20 dBu
(7.75 V)
Phone jack
*1
(Impedance balanced)
AUX SEND 1, 2 600 Ω 10 kΩ Lines
+4 dBu
(1.228 V)
+20 dBu
(7.75 V)
Phone jack
*1
(Impedance balanced)
REC OUT L, R 600 Ω 10 kΩ Lines
-10 dBV
(0.308 V)
+18 dBV
(7.75 V)
RCA pin
(Unbalanced)
Output Jack
Actual Source
Impedance
For Use with Nominal
Output level
Connector
1 kHz
THD+N < 1%
(CEA2006)
1 kHz
THD+N < 10%
(CEA2006)
SPEAKERS A, B < 0.1 Ω
4 Ω Speakers 500 W 630 W
Neutrik speakON
®
NL4
*1
Phone jack
*2
8 Ω Speakers 370 W 460 W
ZW11940
Technical Specifications
2
Block and Level Diagrams
CH INPUT
MIC (XLR)
-60dBu (SW:MIC)–
-30dBu (SW:LINE)
CH1–3
LINE (PHONE)
-50dBu (SW:MIC)–
-20dBu (SW:LINE)
CH4
CH INPUT
MIC (XLR)
-60dBu (SW:MIC)–
-30dBu (SW:LINE)
LINE (PHONE)
-50dBu (SW:MIC)–
-20dBu (SW:LINE)
CH5/6, 7/8
ST CH INPUT
MIC [-60dBu]
LINE
L/MONO [-20dBu]
LINE
R [-20dBu]
ST CH INPUT
CH9/10, 11/12
MIC [-60dBu]
LINE
L [-8dBu]
Only CH11/12
(CH9/10:bypass)
LINE
R [-8dBu]
FOOT SWITCH
+48V
PHANTOM +48V
-10dB
MIC
LINE
HA
HPF
HPF
80Hz
COMP
COMP
LOW
MID
3-Stage EQ
HIGH
LEVEL
AUX2/FX
AUX1
STEREO L
STEREO R
AUX1
AUX2/FX
STEREO L (non MUTE)
STEREO R (non MUTE)
AUX1 (non MUTE)
AUX2/FX
LEVEL
AUX1
LOW
MID
HIGH
AUX2/FX
AUX1
LOW
3-Stage EQ
3-Stage EQ
MID
HIGH
COMP
3-Stage EQ
COMP
LEVEL
HA
SUM
SUM
SUM
SUM
HA
AUX2/FX
AUX1
LOW
MID
HIGH
3-Stage EQ
LEVEL
FX ON
DA
AD
DA
FX RTN
LEVEL
AUX1
3-Stage EQ
DSP
L
R
IN
Digital EFFECT
PARAMETER PROGRAM
MIC
LINE
HA-10dB
Hi-Z
Hi-Z
Digital Audio Section
MASTER
EQ
BASS
BOOST
STEREO
LEVEL
PEAK
+10
+6
0
-6
-10
-20
FEEDBACK
SUPPRESSOR
STEREO
L+R/AUX1
LIMIT
CHA CHB
AMPLIFIER
MODE
PROTECTION
CHA CHB
DA
DA
DA
BA
BA
BA
BA
DA
POWER
AMP
POWER
AMP
LIMITER
STEREO OUT L/MONO
[+4dBu]
STEREO OUT R
[+4dBu]
AUX1 SEND
[+4dBu]
AUX2 SEND
[+4dBu]
SPEAKERS A
L/L+R
SPEAKERS B
R/AUX1
REC OUT L
[-10dBV]
REC OUT R
[-10dBV]
AD
AD
AD
FEEDBACK
SUPPRESSOR
MASTER EQ,
BASS BOOST
MONITOR EQ
MONITOR EQ
AUX2
LEVEL
AUX1
LEVEL
MONITOR EQ
MONITOR EQ
STANDBY
+30dBu
+20dBu
+10dBu
0dBu
-10dBu
-20dBu
-30dBu
-40dBu
-50dBu
-60dBu
+40dBu
Maximum Input Level (PHONE):
[+25dBu]
Maximum Input Level (XLR):
[+15dBu]
Maximum Input Level:
[+15dBu]
Maximum Input Level:
[+25dBu]
Maximum Input Level:
[+25dBu]
Clipping Level:
[+20dBu]
Clipping Level:
[+20dBu]
Clipping Level:
[+3dBu]
Clipping Level:
[+18dBV]
Clipping Level:
[+20dBu]
Clipping Level:
[+8dBu]
Clipping Level:
[+20dBu]
SPEAKERS Maximum Level:
[370W@8Ω (+36.9dBu)]
[500W@4Ω (+35.2dBu)]
SPEAKERS:
[125W@4Ω (+29.2dBu)]
STEREO OUT: [+4dBu]
+30dBu
+20dBu
+10dBu
0dBu
-10dBu
-20dBu
-30dBu
-40dBu
-50dBu
-60dBu
+40dBu
REC OUT: [-10dBV]
AUX1, AUX2 SEND: [+4dBu]
AUX1 (CH1–4)
STEREO L/R
AUX2/FX (CH1–4)
AUX1 (CH5/6–11/12)
AUX2/FX (CH5/6–11/12)
ST CH INPUT LINE:
[-8dBu]
ST CH INPUT LINE:
[-20dBu]
CH INPUT LINE (PHONE):
[-20dBu] @MIC/LINE=LINE
CH INPUT MIC (XLR)
[-30dBu] @MIC/LINE=LINE
CH INPUT LINE (PHONE):
[-50dBu] @MIC/LINE=MIC
CH INPUT MIC (XLR):
[-60dBu] @MIC/LINE=MIC
CH1–4
CH INPUT
CH5/6–11/12
ST CH INPUT (MIC)
CH5/6, 7/8
ST CH INPUT (LINE)
CH9/10, 11/12
ST CH INPUT (LINE)
ST CH INPUT MIC:
[-60dBu]
Manual Development Group
© 2016 Yamaha Corporation
Published 05/2016 POSG-A1
Printed in Malaysia
  • Page 1 1
  • Page 2 2

Yamaha EMX5 spécification

EMX5
Yamaha
Marque
Yamaha
Modèle
EMX5
Catégorie
Mélangeurs audio
Taper
spécification
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes