Bosch Benchmark 1006018 Guide d'installation

Marque: Bosch Benchmark

Modèle: 1006018

Catégorie: Micro-ondes

Taper: Guide d'installation

Ce manuel convient également à

Installation Manual

Built-in and Combination Ovens

HBL8463UC HBL8443UC HBL8743UC HBL8453UC

HBL8753UC HBL87M53UC

Table of Contents

Installation instructi ons

9 Safety Definitions ..................................................... 3

IMPORTANT SAFETY INSTRUCTIONS ........................ 4

Appliance Handling Safety ................................................. 4

Safety Codes and Standards ............................................. 4

Electric Safety ....................................................................... 4

Related Equipment Safety .................................................. 4

Proposition 65 Warning ...................................................... 4

Transport ................................................................................ 5

Bosch Combination Ovens ........................................... 6

Before you Begin ........................................................... 6

Tools and Parts Needed ..................................................... 6

Parts Included ....................................................................... 6

Power Requirements and Grounding ............................... 6

For Best Installation ............................................................. 6

Checklist ................................................................................ 6

Removing Packaging .................................................... 7

Built-in Ovens: ....................................................................... 7

Combination Ovens: ............................................................ 7

Packaging Bracket Removal-Left and Right Sides ........ 7

Preparing Ovens ................................................................... 7

Appliance and Cabinet Cutout Dimensions ............... 8

Dimensions for Single Oven Units .................................... 8

Dimensions for Combination Oven Units ........................ 9

Electrical Installation - Grounding Instructions ....... 11

Electrical Connection ....................................................... 11

Four-wire Connection ....................................................... 11

Three-wire Connection ..................................................... 11

Oven Installation ......................................................... 12

For Best Installation .......................................................... 12

Pre-Assembly of the Combination Oven ...................... 12

Remove Oven Door Prior to Installation ....................... 14

Installing the Oven into the Cabinet .............................. 15

How to Replace the Oven Door ..................................... 16

Testing Operation .............................................................. 17

Bosch

Support ........................................................... 17

Before Calling Service ..................................................... 17

Rating Label ....................................................................... 17

Service ................................................................................ 17

Parts and Accessories ..................................................... 17

4XHVWLRQV"

ZZZERVFKKRPHFRPXV



:HORRNIRUZDUGWRKHDULQJIURP\RX

7KLV%RVFK$SSOLDQFHLVPDGHE\

%6++RPH$SSOLDQFHV&RUSRUDWLRQ

0DLQ6WUHHW6XLWH

,UYLQH&$

9 Safety Definitions

Safety Defi nitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this warning.

NOTICE: This indicates that damage to the appliance or

property may occur as a result of non-compliance with

this advisory.

Note: This alerts you to important information and/or

tips.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFET Y I NS T RU CT I ONS RE AD AND SAVE THESE INSTRUCTIONS

IMPORTANT: SAVE THESE INSTRUCTIONS FOR THE

LOCAL ELECTRICAL INSPECTOR’S USE.

INSTALLER: LEAVE THESE INSTALLATION

INSTRUCTIONS WITH THE UNIT FOR THE OWNER.

OWNER: PLEASE RETAIN THESE INSTRUCTIONS FOR

FUTURE REFERENCE.

WARNING

If the information in this manual is not followed exactly,

fire or shock may result causing property damage or

personal injury.

WARNING

Do not repair, replace or remove any part of the

appliance unless specifically recommended in the

manuals. Improper installation, service or maintenance

can cause injury or property damage. Refer to this

manual for guidance. All other servicing should be done

by an authorized servicer.

Appliance Handling Safety

CAUTION

Safety Codes and Standards

This appliance complies with the latest version of one or

more of the following standards:

▯ CAN/CSA C22.2 No. 61 - Household Cooking Ranges

▯ UL 858 - Household Electric Ranges

▯ CAN/CSA C22.2 No. 150 - Microwave Ovens

▯ UL 923 - Microwave Cooking Appliances

▯ CSA C22.2 No. 64 - Household Cooking and Liquid-

Heating Appliances

▯ UL 1026 - Electric Household Cooking and Food

Serving Appliances

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Electric Safety

Before you plug in an electrical cord, be sure all controls

are in the OFF position.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Installer - show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Important - save these instructions for the local electrical

inspector’s use.

Before installing, turn power OFF at the service panel.

Lock service panel to prevent power from being turned

ON accidentally.

Refer to rating label for more information. See “Rating

Label” under “Service” for rating label location.

Be sure your appliance is properly installed and

grounded by a qualified technician. Installation, electrical

connections and grounding must comply with all

applicable codes.

Related Equipment Safety

Remove all tape and packaging before using the

appliance. Destroy the packaging after unpacking the

appliance. Never allow children to play with packaging

material

Never modify or alter the construction of the appliance.

For example, do not remove leveling legs, panels, wire

covers or anti-tip brackets/screws.

Before starting up the appliance, remove any packaging

material and adhesive film from the cooking

compartment and the door.

Proposition 65 Warning:

This product may contain a chemical known to the State

of California, which can cause cancer or reproductive

harm. Therefore, the packaging of your product may

bear the following label as required by California:

▯ Unit is heavy and requires at least two people

or proper equipment to move.

▯ For double and triple ovens three or more

people are needed to assist with lifting the unit

into place.

▯ Do not lift appliance by door handle.

▯ Hidden surfaces may have sharp edges. Use

caution when reaching behind or under

appliance.



&DQFHUDQG5HSURGXFWLYH+DUPZZZ3:DUQLQJVFDJRY

67$7(2)&$/,)251,$352326,7,21:$51,1*

:$51,1*

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Transport

To avoid damage to the oven vent, use the transport

method shown in the picture below.

Bosch Combination Ovens

The HBL8743UC, HBL8753UC and HBL87M53UC Bosch

combination ovens are sold as sets, each of which

includes two built-in oven components: a conventional

wall oven (lower oven) and either a built-in speed oven or

a microwave oven(upper oven).

▯ For ease of installation and improved alignment, the

oven components are assembled together in the

customer’s home rather than at the factory.

▯ Each of the components are packed in separate

boxes, which are strapped together prior to shipping.

▯ The combination ovens listed here are approved for

use in a single cutout, using single power connection.

▯ Each conventional oven component is designed with

an oven-mounted junction box on top, which is used

for connecting the upper oven power cable.

▯ The hardware required for mounting the speed oven

on top of the conventional oven will be found inside

the conventional oven box.

▯ Each of the oven components has its own rating label,

the component model number, FD number, etc.

Before you Begin

Tools and Parts Needed

▯ Phillips-head screwdriver

▯ Star-head screwdriver (T20)

▯ Measuring tape

▯ Drill with bit (1/8”)

▯ Gloves

▯ Utility Knife

Parts Included

Phillips head screws (6).

Power Requirements and Grounding

The outlet must be properly grounded in accordance with

all applicable codes.

For Best Installation

The oven can be difficult for two people to handle during

installation. It is recommended that three or more people

be available to assist with lifting the unit into place.

Removal of the oven door (to reduce the unit weight and

to provide necessary gripping points) can be

cumbersome unless the detailed door removal

instructions are followed carefully. Do not attempt to

remove the speed oven door.

Please take time to read and follow the instructions

provided for an improved installation experience.

Checklist

Use this checklist to verify that you have completed each

step of the installation process. This can help you avoid

mistakes.

▯ Before installing the oven, be sure to verify the cabinet

dimensions are correct and the required electrical

connections are present.

▯ Refer to additional information in this manual

regarding Safety, Cabinet Dimensions, Removing

Packaging, Electrical Installation, Testing the

Installation and Customer Service.

▯ Remove the lower oven door to reduce the unit weight

and to provide access to gripping points for lifting. See

“Remove Lower Oven Door Prior to Installation”

information.

▯ Move the oven units into place in front of the cabinet

opening, leaving the bottom packaging on the units to

avoid damaging flooring.

▯ Remove the Star-head screws (T-20 size using Star-

head screwdriver) holding the speed microwave oven

to the base of its carton.

▯ Assemble the two units of the combination oven. See

“Pre-Assembly of the Combination Oven”.

▯ Connect the power cable from the lower oven to the

junction box in the cabinet.

▯ Remove the Star-head screws (T-20 size using Star-

head screwdriver) holding the lower oven to the base

of its carton.

▯ Team-lift the unit directly into the cabinet cutout taking

care not to pinch fingers, scratch arms or hands.

▯ Slide the unit all the way into place.

▯ Fasten the unit to the cabinet opening with the screws

supplied using a Philips screwdriver.

▯ Reinstall the oven door removed in Step 3 above.

▯ Consult the complete installation instructions and

follow the remainder of the procedures listed,

including performing operation test.

▯ INSTALLER- Leave the literature pack and the

accessories with the customer.

Removing Packaging

Built-in Ovens:

Cut the straps.

Open top of carton and remove top wood frame.

Lift the carton up and over the appliance to remove, or

carefully cut along the cut line on the back left side of

the carton with a blade shorter than 3/4” and remove

carton.

Carefully remove internal protective packaging taking

care to secure any loose accessories and instruction

manuals.

Remove bracket(s) securing appliance to base pad, if

present.

The unit should stay on the packaging base until ready

to be lifted into cabinet cutout.

Install the appliance according to the installation

instructions.

Combination Ovens:

Cut the straps and remove angle board/strap

protectors from top of carton.

Open top of carton.

Lift the carton up and over the appliance to remove, or

carefully cut along the cut line on the back left side of

the carton with a blade shorter than 3/4” and remove

carton.

Carefully remove the microwave or steam oven carton

from top of bottom carton and place on floor.

Follow instructions on interior cartons for removal of

remaining packaging.

Packaging Bracket Removal-Left and

Right Sides

Note: Actual bracket varies in appearance. The bracket

remains in the packaging base. The unit should stay on

the packaging base until ready to be lifted into cabinet

cutout or onto the lower oven.

Preparing Ovens

Place ovens in front of the cabinet where it is to be

installed so that they are in line with the cabinet cutout.

Check to be sure all packing materials have been

removed from the unit. Also remove the accessories,

oven racks, literature pack and any shipping materials

from inside the oven cavity. Check both ovens for a

double oven or combination oven installation.

Appliance and Cabinet Cutout Dimensions

It is good practice, when an oven is installed at the end

of a cabinet run, adjacent to a perpendicular wall, or

cabinet door, to allow at least 1/4” (6.4 mm) space

between the side of the oven and the wall/door.

For oven support, install 2x4s extending front to back

flush with the bottom and the sides of the opening. The

supporting base must be well secured to the floor/

cabinet and level.

Junction boxes can be located anywhere within reach of

the oven’s power cable.

The cabinet base must be flat and capable of supporting

the weight of the combination oven up to 429 lbs.

(195 kg).

Dimensions for Single Oven Units

The cabinet base must be flat and capable of supporting

a weight of at least 232 lbs (105 kg).

Under oven dimensions are provided as a general

guideline and may be adjusted as needed based on a

particular application. Consult a design professional for

optimizing personal preferences.

Single Oven Appliance Dimensions

Single Oven Wall Mount Installation

*For single ovens installed into a wall cabinet, the

junction box may be located above, beneath, left or right

of the unit within reach of the power cord.

**For oven installation in a wall cabinet, the control panel

overlap is a minimum

" (10mm) to max. 2" (51mm).

Single Oven Flush Mount Installation

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

Top View

Side View

 PP





 PP



ʌ¼ʚ

PLQë

PD[



ò



IOXVKLQVHW

GHSWK

ò







ô

UHYHDO

FOHDWV

ô

UHYHDO

FOHDWV

 PP

ò















ǫ



ǩ



IOXVK

FXWRXW

KHLJKW

 PP

UHYHDO

FOHDWV

Under-Counter Installation

* Includes ¾” (19 mm) base plate.

**For single ovens installed under a cabinet, the junction

box should be located to the right or left of the unit within

range of the power cord.

Dimensions for Combination Oven Units

The cabinet base must be flat and capable of supporting

the weight of the combination oven up to 429 lbs

(195 kg).

Combination Oven Appliance Dimensions

Combination Oven Traditional Installation

Note: Junction box may be installed above, below, to the

left or to the right of the unit within reach of the power

cord.





ë



é



ê



ê







 PP





 PP



ë





ç¼ʚ



ʎ¼ʓʘ



ʌ¼ʚ



ç¼ʚ



ê



ê



PLQ









PD[















Combination Oven Flush Mount Installation

Flush installation requires two side cleats to be attached

inside the cabinet frame, recessed from the front.

RS

 PP









ë

UHYHDO

FOHDWV

ë

UHYHDO

FOHDWV

ê

IOXVKLQVHW

GHSWK

ê

UHYHDOFOHDWV

 PP



6LGH9LHZ

ê

è¼ʚ

IOXVKFXWRXW

KHLJKW

Electrical Installation - Grounding Instructions

The assembled combination oven should be moved in

front of the cabinet opening and the power cable from

the lower oven should be connected to the cabinet

junction box.

All model ovens on the front cover of this installation

instruction manual are dual rated, designed to be

connected to either 208 or 240V AC, 60 Hz, 4 wire,

single-phase power supply.

The electrical supply should be a 4-wire single phase AC.

Install a suitable conduit box (not furnished). An

appropriately-sized, UL-listed conduit connector must be

used to correctly attach the conduit to the junction box.

Note: Local codes may vary. Installation, electrical

connections and grounding must comply with all

applicable local codes.

If local codes permit grounding through the electrical

supply neutral, connect both the white neutral wire and

the green ground wire from the oven to the white neutral

eletrical supply wire.

Electrical Connection

The four-wire connection is preferred, but where local

codes permit, the three wire connection is also

acceptable.

9 WARNING

When connected to a 4 or 5-wire, 120/208-Volt 3-

phase power supply, the phase C conductor is not

required for the operation of the appliance.

Four-wire Connection

Ungrounded Neutral

▯ Connect the red oven wire to the red electrical supply

wire (hot wire).

▯ Connect the black oven wire to the black electrical

supply wire (hot wire).

▯ Connect the white neutral oven wire to the white

neutral (not bare or green ground) electrical supply

wire.

▯ Connect the green ground oven wire to the bare or

green ground electrical supply wire.

Three-wire Connection

Grounded Neutral

▯ Connect red wire from oven to red wire in junction box.

▯ Connect black wire from oven to black wire in junction

box.

▯ Connect both green ground wire and white wire from

oven to white, green or bare neutral wire in junction

box.

The conduit cable, where connected at the oven, swivels.

Rotate conduit cable upward (or downward) and direct

through hole prepared in cabinet to attach to junction

box.

To maintain serviceability, the flex conduit must not be

shortened and should be routed to permit temporary

removal of the oven.

Model Circuit Required

HBL8463UC

HBL8443UC

HBL8453UC

208V, 60 Hz/ 240V, 60 Hz

30 AMP

HBL8743UC

HBL8753UC

HBL87M53UC

208V, 60 Hz/ 240V, 60 Hz

40 AMP

SRZHUVXSSO\

MXQFWLRQER[

UHGZLUHV

JUHHQRUEDUH

JUHHQZLUH

8/OLVWHG

FDEOHIURP

ZKLWHZLUHV

EODFNZLUHV

ZLUH

FRQQHFWRU

RYHQ

SRZHUVXSSO\

MXQFWLRQER[

UHGZLUHV

ZKLWHEDUHRU

ZKLWHZLUH

JUHHQZLUH

FDEOHIURP

8/OLVWHG

EODFNZLUHV

RYHQ

FRQQHFWRU

Oven Installation

NOTICE: Before installing the appliance, be sure to

verify the cabinet dimensions and electrical connections.

For Best Installation

The oven can be difficult for two people to handle during

installation. It is recommended to have three or more

people available to assist with lifting the unit into place.

Removal of the oven door during installation (to provide

the necessary handholds and to significantly reduce the

unit weight) can be cumbersome unless the detailed

door removal instructions are followed carefully. Please

take time to read and follow the instructions provided for

an improved installation experience.

Pre-Assembly of the Combination Oven

Combination ovens require the oven and the microwave

to be assembled prior to installing the combination unit

into the wall cabinet.

Parts Provided

Assembly of the two Oven Units

Notes

▯ Do not place the oven into the wall cabinet until after

mounting the speed oven on top of the lower oven and

securing it with the universal connector brackets.

▯ The universal connector brackets are interchangeable

for the left and right sides of the oven. Be sure the

taller vertical edge of the bracket is positioned to the

outside of the oven.

Install both universal connector brackets on top of the

lower oven using six (6) of the screws provided.

Tighten screws securely, but do not overtighten.

Install decorative trim.

Universal connector bracket

(2):

in parts box on top of oven

Screws (16):

in red bag inside parts box

on top of oven.

Oven Mounting Screws (8):

Screws are included to

secure the oven trim to the

cabinet. The screws are

located in a small plastic bag

affixed to the literature pack

bag.

Trim Piece:

in plastic bag on top of oven.

Position the decorative trim

piece so the flanges with the

holes in them face to the rear

of the oven.

Align the outer flanges with

the outside of the universal

brackets. Fasten with one (1)

screw each into the end hole

of each universal bracket.

Tighten screws securely, but

do not overtighten.

Place the speed oven on top of the universal

connector brackets and fasten in place using three (3)

screws per side. Tighten the screw securely, but do

not overtighten.

Note: The existing screws in the speed oven base

help with alignment. When lowering the speed oven

into place on the universal connector brackets, allow

these screw heads to slide into the slots as shown in

the illustration below. The screw nearest the front of

the speed oven should slide into the base of the slope

at the front of the bracket.

Continue to “Connecting the Speed Oven Electrical

Conduit to the Lower Oven”.

Connecting Speed Oven Electrical Conduit to

Lower Oven

Note: When installing the combination unit, the power

cable must be properly attached to the oven-mounted

junction box. This must be done prior to supplying

electrical power to the oven unit.

9 WARNING

Check to be sure that no electrical power has yet

been supplied to the oven.

Remove the oven-mounted junction box cover located

on the top rear of the oven. (See image below).

Remove the cap from the conduit access hole in the

side of the oven-mounted junction box.

Guide the wires from the conduit cable coming from

the speed oven through the hole in the oven-mounted

junction box. There are four wires coming from the

speed oven.

Snap the conduit connector into the hole by pressing it

in until it clicks into place.

Follow the wiring diagram label and match and

connect each wire by color to the wires attached to the

wiring block inside the oven-mounted junction box.

Push the bare end of the wire until it is snug in the

wiring block then tighten down the retaining screw on

each wire.

Tighten securely, but do not overtighten.

See previous illustration in Step 3 for finished

appearance.

Replace the oven-mounted junction box cover and

tighten the two screws holding it in place.

Tighten securely, but do not overtignten.

Remove Oven Door Prior to Installation

It is recommended to remove the conventional (lower)

oven door to help reduce the unit weight.

NOTICE: Do not remove the speed oven door.

How to Remove the Oven Door

9 WARNING

▯ Make sure oven is cool and power to the oven

has been turned off before removing the door.

Failure to do so could result in electrical shock or

burns.

▯ The oven door is heavy and parts of it are fragile.

Use both hands to remove the oven door. The

door front is glass. Handle carefully to avoid

breakage.

▯ Grasp only the side of the oven door. Do not

grasp the handle as it may swing in your hand

and cause damage or injury.

▯ Failure to grasp the oven door firmly and properly

could result in personal injury or product damage.

▯ To avoid injury from hinge bracket snapping

closed, be sure both levers are securely in place

before removing the door. Also, do not force door

open or closed-the hinge could be damaged and

injury could result.

▯ Do not lay removed door on sharp or pointed

objects as this could break the glass. Lay on a

flat, smooth surface, positioned so that the door

cannot fall over.

To help avoid injury or damage, be sure to read the

above WARNING before attempting to remove the oven

door.

Open the oven door to its fully open position.

Flip levers on hinges toward you.

Note: It may be necessary to use a tool, such as a

screwdriver, to gently pry the upper part of the lever

away from the housing. Take care to avoid scratching

the housing.

Bring both door hinge levers to their fullest down

position as shown in the illustration. The left and right

door hinges differ slightly but operate in the same

manner.

Close the oven door until it catches on the hinge stop

levers, locking the hinges at the proper angle for door

removal. The door will be open about 7 inches at the

top. This takes the spring tension off the hinges so the

door can be easily lifted out.

9 CAUTION

PINCH HAZARD

Closing the door 7” takes the pressure off of the

spring. If this isn’t done, the door can still be

removed but the latch will now slam shut and will

pinch or cut your hand.

The door is heavy. Use both hands to firmly grip it by

the sides. Do not grip the door by the handle.

Maintaining the door angle, lift the door straight up

approximately 3/4” to unhook the hinges from the

slots and then pull it out towards you until the hinges

are clear of the oven housing.

Place the door in a convenient and stable location for

cleaning.

Installing the Oven into the Cabinet

9 CAUTION

It is recommended to wear gloves and long sleeves

to protect hands and forearms from abrasion and

potential scratches during the lifting process. It is

also recommended to take off watches and jewelry

and to wear work shoes during installation for foot

protection.

9 CAUTION

Three people or proper equipment are needed to

safely lift the combination oven into the cabinet

opening.

NOTICE: To avoid damage to the door, do not lift, pull or

push the unit during installation by using any oven door

handle as a gripping point.

Lifting Recommendations

There is a ridge across the top front of the oven cavity.

Lift by grasping this ridge with one hand while placing the

other hand on the back of the unit (for helpers lifting from

the sides of the unit). If a third helper is lifting from the

front, both hands should lift by holding this ridge area.

9 CAUTION

DO NOT attempt to lift the unit by holding the oven’s

upper heating element.

Proceed to lift the oven following the guidelines below

with the door removed:

▯ Lift points (1) on the front of the unit are for lifting from

the sides of the unit. Lift point (3) on the front of the

unit is for a third person to help lift the unit.

▯ Lift point (2) on the back of the unit shows the location

of the opposite hand for the helpers lifting from the

sides of the unit. Adjust the location as needed to

facilitate the lift.

Placing Oven Into Cabinet Opening

The unit and its bottom packaging (pallet) should be

positioned close to and in front of the cabinet opening

prior to beginning to lift the unit into place.

Lift or slide unit into the cabinet cutout without allowing

the unit base to contact the flooring.

Guide the unit straight back into the cabinet cutout.

Push the unit straight in until the oven trim is about

2 inches from being flush with cabinet wall.

Note: Be careful not to crimp the flexible conduit

between the oven and the cabinet back wall. If

necessary, guide the flexible conduit into the wall of

cabinet access hole so it doesn’t prevent the unit from

being pushed all the way into the cabinet opening. The

oven should be straight and level.

Push the unit all the way back into the cabinet cutout

until the front edge of the unit is flush with the front of

the cabinet.

Install the supplied screws through the tap holes in the

trim (2 screws for single ovens, 4 screws for

combination ovens). It is recommended to drill pilot

holes for the trim screws.

To ensure the door and oven function properly, the

screws should be installed on the face of the side trim

Replace the oven door accordingly. See “Re-Install the

Oven Door”.

How to Replace the Oven Door

Holding the door firmly in both hands, grip it on either

side, not by the handle.

Tilt the door back slightly towards you until it opens

about 7 inches at the top.

Slide the hinges into the slots as far as they will go and

then lower the door straight down. The angle of the

door may need to be adjusted slightly to allow the

hinges to engage properly and the door to lower into

place. The door should lower about 3/4” and stop. If

not, the hinges have not engaged properly and the

door could fall if it is released.

Once both hinges are fully engaged as described in

Step 3, gently open the door until it is fully open.

Push the levers on both the hinges up and forward

until they are locked into the slot and flush with the

front of the oven body.

Close and open the door slowly to be sure it is

correctly and securely in place.

Single Oven Combination Oven

 



 











Testing Operation

Turn on power at the breaker.

Test the oven mode.

Select the BAKE mode. See the Use and Care Manual

for detailed operation instructions.

Verify that the oven light comes on and the oven

begins to preheat.

Test the door lock.

Set the SELF CLEAN mode. Confirm that the door

locks when the lock icon appears in the display.

If any of the tests do not result as explained above,

contact Customer Service for assistance. Otherwise,

the installation is complete at this time.

Bosch

Support

Before Calling Service

See the Use and Care Manual for troubleshooting

information. Refer to the “Statement of Limited Product

Warranty” in the Use and Care Manual.

To reach a service representative, see the contact

information at the front of the manual or in the following

section. Please be prepared with the information printed

on your product rating label prior to calling.

Rating Label

Each component of a combination oven has its own

rating label.

The rating label shows the model, FD number and serial

number. Refer to the rating label when requesting

service. The rating label location varies based on the

oven model.

Rating Label Location Speed Oven

The rating label of the speed oven is located at the inside

of the appliance door.

Rating Label Location Conventional Oven

The rating label of the conventional (lower) oven is

located at the left hand side of the door trim.

To avoid having to search for each piece of information

when calling, you can enter the four items needed in the

spaces provided below.

Keep your invoice or escrow papers for warranty

validation if service is needed.

Service

We realize that you have made a considerable

investment in your kitchen. We are dedicated to

supporting you and your appliance so that you have

many years of creative cooking.

Please don’t hesitate to contact our Customer Support

Department if you have any questions or in the unlikely

event that your Bosch® appliance needs service. Our

service team is ready to assist you.

USA

800-944-2904

www.bosch-home.com/us/support

Canada

800-944-2904

www.bosch-home.ca/en/support

Parts and Accessories

Parts, filters, descalers, stainless steel cleaners and more

can be purchased in the Bosch

eShop or by phone.

USA

www.bosch-home.com/us/store

Canada

Marcone 800-482-6022

Reliable Parts 800-941-9217

Conventional Oven

Model No.

FD-No.

Speed Oven

Model No.

FD-No.

Date of Purchase

Customer Service

Table des matières

Noti ce de montage

9 Définitions de sécurité ........................................... 19

IMPORTANTES CONSIGNES DE SÉCURITÉ ............. 20

Sécurité de manutention des appareils ........................ 20

Codes et normes de sécurité ......................................... 20

Sécurité électrique ............................................................ 20

Sécurité apparentée concernant l´équipement .......... 21

Avertissement issu de la proposition 65 ...................... 21

Transport ............................................................................. 21

Fours combinés Bosch ............................................... 22

Avant de commencer .................................................. 22

Outils et pièces nécessaires ........................................... 22

Pièces comprises .............................................................. 22

Exigences électriques et mise à la terre ...................... 22

Pour de meilleurs résultats d'installation ...................... 22

Liste de vérification ........................................................... 22

Retrait de l’emballage ................................................. 23

Fours intégrés : .................................................................. 23

Fours combinés : ............................................................... 23

Retrait des brides d'emballage – côtés gauche

et droit ................................................................................. 23

Préparation des fours ....................................................... 23

Dimensions de l'appareil et de la découpe des

armoires ....................................................................... 24

Dimensions pour les fours simples ............................... 24

Dimensions des modules de fours combinés ............. 25

Raccordement électrique : directives de mise

à la terre ....................................................................... 27

Raccordement électrique ................................................ 27

Raccordement à quatre fils ............................................. 27

Raccordement à trois fils ................................................ 27

Installation du four ...................................................... 28

Pour une installation optimale ........................................ 28

Pré-assemblage de four combiné ................................. 28

Retrait de la porte du four avant installation ................ 30

Installation du four dans l'armoire ................................. 31

Remontage de la porte du four ...................................... 32

Opération d’essai .............................................................. 33

Soutien Bosch

........................................................... 33

Avant d’appeler le service de réparations ................... 33

Plaque signalétique .......................................................... 33

Service ................................................................................ 33

Pièces et accessoires ..................................................... 33

9RXVDYH]GHVTXHVWLRQV"

ZZZERVFKKRPHFRPXV

ââ

1RXVQRXVIHURQVXQSODLVLUGHYRXVVHUYLU

&HWDSSDUHLOpOHFWURPpQDJHU%RVFKHVWIDEULTXpSDU

%6++RPH$SSOLDQFHV&RUSRUDWLRQ

0DLQ6WUHHW6XLWH

,UYLQH&$

9 Définitions de sécurité

Défi nitions de sécurité

9 AVERTISSEMENT

Ceci indique que le non-respect de cet

avertissement peut entraîner des blessures graves,

voire la mort.

9 ATTENTION

Ceci indique que le non-respect de cet

avertissement peut entraîner des blessures légères

ou de gravité moyenne.

AVIS : Ceci indique que la non-conformité à cet avis de

sécurité peut entraîner des dégâts matériels ou

endommager l'appareil.

Remarque : Ceci vous signale des informations et/ou

indications importantes.

9 IMPORTANTES CONSIGNES DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS

IMPORTANTES CONSI GNES DE SÉCURI T ÉLI RE ET CONSE RV E R CE S INSTRUCTIONS

IMPORTANT : CONSERVEZ CES CONSIGNES À

L'INTENTION DE L'INSPECTEUR EN ÉLECTRICITÉ.

INSTALLATEUR : PRIÈRE DE LAISSER CES

INSTRUCTIONS D'INSTALLATION AVEC CET APPAREIL

À L'INTENTION DU PROPRIÉTAIRE.

PROPRIÉTAIRE : PRIÈRE DE CONSERVER CES

INSTRUCTIONS POUR POUVOIR VOUS Y RÉFÉRER

ULTÉRIEUREMENT.

AVERTISSEMENT

Si l’information de ce guide n’est pas suivie exactement,

il peut en résulter un incendie ou un choc électrique

causant des dommages à la propriété, des blessures ou

la mort.

AVERTISSEMENT

Ne réparez, remplacez, ni ne retirez aucune partie de

l'appareil, excepté si les manuels recommandent de le

faire. Une installation, un entretien ou une inspection

incorrects peuvent occasionner des blessures ou des

dommages matériels. Reportez-vous au présent manuel

pour obtenir des indications. Toute autre intervention doit

être effectuée par un technicien agréé.

Sécurité de manutention des appareils

ATTENTION

Codes et normes de sécurité

Cet appareil est conforme aux plus récentes versions de

l'une ou plus des normes suivantes :

▯ CAN/CSA C22.2 No. 61 - Cuisinières pour usage

ménager (Household Cooking Ranges)

▯ UL 858 - Cuisinières électriques domestiques

(Household Electric Ranges)

▯ CAN/CSA C22.2 No. 150 - Fours à micro-ondes

(Microwave Ovens)

▯ UL 923 - Appareils de cuisson à micro-ondes

(Microwave Cooking Appliances)

▯ CSA C22.2 No. 64 - Appareils de cuisson domestique

et de chauffage des liquides (Household Cooking and

Liquid-Heating Appliances)

▯ UL 1026 - Appareils électriques domestiques pour la

cuisson et la préparation des aliments (Electric

Household Cooking and Food Serving Appliances)

Il incombe au propriétaire et à l'installateur de déterminer

si des exigences et/ou normes additionnelles

s'appliquent pour des installations spécifiques.

Sécurité électrique

Avant de brancher le cordon électrique, vérifier que

toutes les commandes sont à la position OFF (Arrêt).

S’il y a lieu, conformément au Code national de

l’électricité (ou au Code canadien de l’électricité), cet

appareil doit être installé sur un circuit de dérivation

séparé.

Installateur : indiquez au propriétaire l’emplacement du

disjoncteur ou du fusible. Identifiez sa position pour

pouvoir le retrouver facilement.

Important : Conservez ces consignes à l’intention de

l’inspecteur local en électricité.

Avant l'installation, coupez l'alimentation au panneau de

service. Verrouillez le panneau de service pour

empêcher que l'alimentation ne soit rétablie par accident.

Consultez la plaque signalétique pour de plus amples

renseignements. Consultez la section « Plaque

signalétique » dans « Réparation » pour l'emplacement

de la plaque signalétique.

Assurez-vous que l’appareil est correctement installé et

mis à la terre par un technicien qualifié. L’installation, les

raccordements électriques et la mise à la terre doivent

être conformes avec tous les codes en vigueur.

▯ L’appareil est lourd et son déplacement exige

au moins deux personnes ou encore un

équipement approprié.

▯ Il est recommandé de faire intervenir trois

personnes ou plus pour aider à soulever les

fours doubles ou triples afin de les mettre en

place.

▯ Ne pas soulever l'appareil électroménager par

la poignée de porte.

▯ Les surfaces cachées peuvent comporter des

arêtes vives. Redoubler de vigilance quand

vous passez la main derrière ou sous l'appareil

électroménager.

La page charge ...

Bosch Benchmark 1006018 Guide d'installation

Marque: Bosch Benchmark

Modèle: 1006018

Catégorie: Micro-ondes

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Bosch Benchmark 1006018 Installation guide
español: Bosch Benchmark 1006018 Guía de instalación

Bosch Benchmark 1006018 Guide d'installation

Ce manuel convient également à

Bosch Benchmark 1006018 Guide d'installation

dans d''autres langues

Autres documents