LG RV1309AT Le manuel du propriétaire

Protocol P154

Sanitization Performance of Residetial

Clothes dryer

Protocole P154

Performances d’assainissement

des séche-linge domestiques

DLEX8377WM

DLEX8377NM

DLEX8377CM

DLEX8377RM

P/No. 3828EL3010L

Before beginning installation, read these

instructions carefully. This will simplify installation

and ensure that the dryer is installed correctly and

safely. Leave these instructions near the dryer

after installation for future reference.

To contact LG Electronics, 24 hours a day,

7 days a week:

1-888-LGCANADA

Or visit us on the Web at: ca.lge.com

Pour contacter LG Electronics, 24 heures

par jour, 7 jours par semaine :

1-888-LGCANADA

Ou visitez notre site Web à l’adresse :

ca.lge.com

Avant de commencer à installer votre sécheuse, lisez

attentivement ces instructions. Cela simpliﬁera votre

installation et assurera que la sécheuse est installée

correctement et en toute sécurité. Conservez ces

instructions à proximité de la sécheuse après son

installation, pour référence future.

DLGX8388WM

DLGX8388NM

DLGX8388CM

DLGX8388RM

Congratulations on your purchase

and welcome to the LG family. Your

new LG Dryer combines the most

advanced drying sensor technology

with simple operation and high

efficiency. By following the

operating and care instructions

in this manual, your dryer will

provide you with many years of

reliable service.

THANK YOU!

I N T RO D U C T I O N

INSTALLATION INSTRUCTIONS

Choose the Proper Location ................................ 10

Clearances ........................................................... 10

Installation With Optional

Pedestal Base or Stacking Kit .............................. 11

Leveling the Dryer ................................................ 12

Reversing the Door Swing .................................... 12

Changing the Dryer Vent Location ....................... 13

Venting the Dryer ............................................ 14, 15

Connecting Gas Dryers .................................. 16, 17

Connecting Electric Dryers ................................... 18

Special Requirements for Manufactured

or Mobile Homes .................................................. 19

Final Installation Check ....................................... 19

HOW TO USE

Sorting Loads ....................................................... 20

Loading the Dryer ................................................. 20

Check the Lint Filter Before Every Load ............... 20

Control Panel Features ......................................... 21

Cycle Guide .......................................................... 22

The LCD Display ................................................... 23

Operating the Dryer .............................................. 24

Cycle Setting Buttons .......................................... 25

Cycle Option Buttons .......................................... 25

Special Functions ................................................. 26

Other Functions .............................................. 26, 27

Steam Functions ............................................ 27–29

Steam Cycle Guide .............................................. 29

TROUBLESHOOTING

Before Calling for Service ............................... 31–33

USER-MAINTENANCE INSTRUCTIONS

Regular Cleaning .................................................. 30

SPECIFICATIONS/OPTIONAL

ACCESSORIES

Key Dimensions and Speciﬁcations ..................... 34

Optional Accessories ........................................... 34

Pedestal Installation ....................................... 35, 36

Stacking Kit Installation .................................. 37, 38

IMPORTANT SAFETY INSTRUCTIONS

Basic Safety Precautions ....................................... 3

What to Do if You Smell Gas .................................. 4

Grounding Instructions ........................................... 5

Safety Instructions for Installation ...................... 5, 6

Safety Instructions for Steam Functions ................ 6

Safety Instructions for Connecting Electricity ....... 7

PARTS AND FEATURES

Special Features ..................................................... 8

Key Parts and Components ................................... 9

WARRANTY ................................................... 39

Product Registration Information

Model:

Serial Number:

Date of Purchase:

The model and serial number can be located on

the rating plate inside the front door.

2

I M P O RTA N T S A F E T Y I N S T RU C T I O N S

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read

and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.

These words mean:

wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions.

wWARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of

injury, and tell you what can happen if the instructions are not followed.

BASIC SAFETY PRECAUTIONS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Read all instructions before using the dryer.

• Before use, the dryer must be properly installed

as described in this manual.

• Do not place items exposed to cooking oils in

your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that

could cause a load to catch ﬁre.

• Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂammable or explosive substances as they give

off vapors that could ignite or explode.

• Do not reach into the dryer if the drum or any

other part is moving.

• Do not repair or replace any part of the dryer

or attempt any servicing unless speciﬁcally

recommended in this Use and Care Guide or

in published user-repair instructions that you

understand and have the skills to carry out.

• Do not tamper with controls.

• Before the dryer is removed from service or

discarded, remove the door to the drying

compartment.

• Do not allow children to play on or in the dryer.

Close supervision of children is necessary when

the dryer is used near children.

• Do not use fabric softeners or products to

eliminate static unless recommended by the

manufacturer of the fabric softener or product.

• Do not use heat to dry articles containing

foam rubber or similarly textured rubber-like

materials.

• Keep area around the exhaust opening and

adjacent surrounding areas free from the

accumulation of lint, dust, and dirt.

• The interior of the dryer and exhaust vent

should be cleaned periodically by qualiﬁed

service personnel.

• Do not install or store the dryer where it will be

exposed to the weather.

• Always check the inside of the dryer for foreign

objects.

• Clean lint screen before or after each load.

3

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

• Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this appliance or any other

appliances.

• Installation and service must be

performed by a qualiﬁed installer,

service agency, or the gas supplier.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

1. Do not try to light a match or cigarette,

or turn on any gas or electrical

appliance.

2. Do not touch any electrical switches.

Do not use any phone in your building.

3. Clear the room, building, or area of all

occupants.

4. Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions carefully.

5. If you cannot reach your gas

supplier, call the ﬁre department.

WHAT TO DO IF YOU SMELL GAS:

I M P O RTA N T S A F E T Y I N S T RU C T I O N S

4

GROUNDING INSTRUCTIONS

I M P O RTA N T S A F E T Y I N S T RU C T I O N S

5

This appliance must be grounded. In the event

of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing

a path of least resistance for electric current.

This appliance must be equipped with a cord

having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into

an appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances.

wWARNING — Improper

connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualiﬁed electrician or service

person if you are in doubt as to whether the

appliance is properly grounded.

Do not modify the plug provided with the

appliance. If it will not ﬁt the outlet, have a proper

outlet installed by a qualiﬁed electrician.

This appliance must be connected to a grounded

metal, permanent wiring system or an equipment-

grounding conductor must be run with the circuit

conductors and connected to the equipment-

grounding terminal or lead on the appliance.

Electrical shock can result if the dryer is not

properly grounded.

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

• Properly ground dryer to conform with all

governing codes and ordinances. Follow

details in the installation instructions. Electrical

shock can result if the dryer is not properly

grounded.

• Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not

properly grounded.

• Install and store the dryer where it will not be

exposed to temperatures below freezing or

exposed to the weather.

• All repairs and servicing must be performed

by an authorized servicer unless speciﬁcally

recommended in this Owner’s Guide. Use

only authorized factory parts. Failure to follow

this warning can cause serious injury, ﬁre,

electrical shock, or death.

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

•

To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to

follow this warning can cause serious injury, ﬁre,

electrical shock, or death.

• Connect to a properly rated, protected,

and sized power circuit to avoid electrical

overload. Improper power circuit can melt,

creating electrical shock and/or ﬁre hazard.

• Remove all packing items and dispose of all

shipping materials properly. Failure to do so

can result in death, explosion, ﬁre, or burns.

• Place dryer at least 18 in. above the ﬂoor

for a garage installation. Failure to do so can

result in death, explosion, ﬁre, or burns.

• Keep all packaging from children. Packaging

material can be dangerous for children. There is

a risk of suffocation.

I M P O RTA N T S A F E T Y I N S T RU C T I O N S

6

READ ALL INSTRUCTIONS BEFORE USE

SAFETY INSTRUCTIONS FOR INSTALLATION

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

Exhaust/Ducting:

• Gas dryers MUST be exhausted to the

outside. Failure to follow these instructions

can result in ﬁre or death.

• The dryer exhaust system must be exhausted

to the outside of the dwelling. If the dryer is

not exhausted outdoors, some ﬁne lint and

large amounts of moisture will be expelled

into the laundry area. An accumulation of

lint in any area of the home can create a health

and ﬁre hazard.

• Use only rigid metal or ﬂexible metal 4-in.

diameter ductwork inside the dryer cabinet

or for exhausting to the outside. Use of

plastic or other combustible ductwork can

cause a ﬁre. Punctured ductwork can cause

a ﬁre if it collapses or becomes otherwise

restricted in use or during installation.

• Ductwork is not provided with the dryer, and

you should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the dryer

is not in use. Failure to follow these instructions

can result in ﬁre or death.

•

The exhaust duct must be 4 in. (10 cm) in

diameter with no obstructions. The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before

installing your new dryer. Failure to follow

these instructions can result in ﬁre or death.

• Rigid or semi rigid metal ducting is

recommended for use between the

dryer and the wall. In special installations

when it is impossible to make a connection

with the above recommendations, a UL-

listed ﬂexible metal transition duct may be

used between the dryer and wall connection

only. The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁre or death.

• DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁciency

of the exhaust system. Secure all joints with

duct tape. For complete details, follow the

Installation Instructions. Failure to follow these

instructions can result in ﬁre or death.

SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS

• Do not open the dryer door during steam

cycles. Failure to follow these instructions can

result in a burn hazard.

• Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, or other

ﬂammable or explosive substances as they

give off vapors that could ignite or explode.

Failure to follow these instructions can result in

ﬁre or death.

• Do not ﬁll the steam feeder with gasoline,

dry-cleaning solvents, or other ﬂammable or

explosive substances. Failure to follow these

instructions can result in ﬁre or death.

• Do not touch the steam nozzle in the drum

during or after the steam cycle. Failure to

follow these instructions can result in a burn

hazard.

• Do not ﬁll the steam feeder with hot water

(over 86° F / 30° C). Failure to follow these

instructions can result in a burn hazard.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

• Do not, under any circumstances, cut or

remove the ground prong from the power

cord. To prevent personal injury or damage to

the dryer, the electrical power cord must be

plugged into a properly grounded outlet.

• For personal safety, this dryer must be

properly grounded. Failure to do so can result

in electrical shock or injury.

• Refer to the installation instructions in this

manual for speciﬁc electrical requirements

for your model. Failure to follow these

instructions can create an electrical shock

hazard and/or a ﬁre hazard.

• This dryer must be plugged into a properly

grounded outlet. Electrical shock can result if

the dryer is not properly grounded. Have the

wall outlet and circuit checked by a qualiﬁed

electrician to make sure the outlet is properly

grounded. Failure to follow these instructions

can create an electrical shock hazard and/or a

ﬁre hazard.

• The dryer should always be plugged into

its own individual electrical outlet which

has a voltage rating that matches the rating

plate. This provides the best performance

and also prevents overloading house wiring

circuits which could cause a ﬁre hazard from

overheated wires.

• Never unplug your dryer by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet. The power cord

can be damaged, resulting in a risk of ﬁre and

electrical shock.

• Repair or replace immediately all power

cords that have become frayed or otherwise

damaged. Do not use a cord that shows

cracks or abrasion damage along its length

or at either end. The power cord can melt,

creating electrical shock and/or ﬁre hazard.

• When installing or moving the dryer, be

careful not to pinch, crush, or damage

the power cord. This will prevent injury and

prevent damage to the dryer from ﬁre and

electrical shock.

SAVE THESE INSTRUCTIONS

I M P O RTA N T S A F E T Y I N S T RU C T I O N S

7

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

PA RT S A N D F E AT U R E S

SPECIAL FEATURES

4

1

2

1

EASY-TO-USE CONTROL PANEL

Rotate the Cycle Selector Knob to select the

desired dry cycle. Add cycle options or adjust

settings with the touch of a button.

2

3

4

EASY-ACCESS REVERSIBLE DOOR

Wide-opening door provides easy access for

loading and unloading. Door swing can be

reversed to adjust for installation location.

ULTRA-CAPACITY STAINLESS STEEL DRUM

WITH DRUM LIGHT

The ultra-large stainless steel drum offers

superior durability. The drum is equipped with a

yellow light that illuminates when the dryer door

is open and turns off when the door is closed.

3

HELPFUL STEAM FUNCTIONS

LG’s new steam technology allows you to inject

fabrics with a swirling jet of hot steam to refresh

clothes, reduce static, and make ironing easier.

Simply select the STEAM FRESH

™

cycle, or you

can add a steam option to selected cycles.

5

LCD DISPLAY SCREEN

The easy-to-read display screen shows cycle

options and information and provides status

messages during operation.

8

1

2

LEVELING FEET

Four leveling feet (two in the front, and two in

the back) adjust to improve dryer stability on

uneven floors.

Included Accessories

Drying Rack

2

1

FRONT-MOUNT LINT FILTER

Front-mounted lint filter allows for easy access

and cleaning after every load.

Terminal Block

Access Panel

(Electric Models)

Rear of Dryer

Power Cord Location

(Gas Models)

Gas

Connection

Location

(Gas Models)

Exhaust Duct

Outlet

KEY PARTS AND COMPONENTS

In addition to the special features and

components outlined in the Special Features

section, there are several other important

components that are referenced in this manual.

DRYING RACK

Use the drying rack with the RACK DRY cycle

option. The drying rack allows items, such as

sweaters, delicates, and gym shoes, to be placed

in a flat position for drying.

3

PA RT S A N D F E AT U R E S

PLC MODEM

The PLC modem is used when installing the

optional Remote Laundry Monitor (purchased

separately).

4

3

4

9

I N S TA L L AT I O N I N S T RU C T I O N S

CHOOSE THE PROPER LOCATION

• Store and install the dryer where it will not be

exposed to temperatures below freezing or

exposed to outdoor weather conditions.

• Choose a location with a solid, level ﬂoor.

• If the dryer is being installed in a garage,

place the dryer at least 18 in. (46 cm) above

the ﬂoor.

CLEARANCES

• Most installations require a minimum 5½ in.

(14 cm) clearance behind the dryer for the

exhaust ducting.

• Allow minimum clearances of at least 1 in.

(2.5 cm) on the sides and back to minimize

vibration and noise.

• Allowing additional clearance for installation and

servicing is recommended.

• Be sure to allow for wall, door, or ﬂoor moldings

that may increase the required clearances.

• Allow at least 24 in. (61 cm) in front of the dryer

to open the door.

IMPORTANT: Read all installation instructions completely before

installing and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. Detailed instructions

concerning electrical connections, gas connections, and exhaust requirements are provided on the

following pages.

• Properly ground dryer to conform with all

governing codes and ordinances.

• To reduce the risk of electric shock, do not

install the dryer in damp or wet locations.

• If you are installing your dryer in a manufactured

or mobile home, please refer to the section

Special Requirements for Manufactured or

Mobile Homes.

Additional Instructions for closet installations:

• The closet door must allow for sufﬁcient airﬂow.

Refer to the diagram above for minimum vent

opening requirements. A louvered door is also

acceptable.

• Make sure that there is at least 18 in. (46 cm) of

clearance above the dryer.

Closet Door Vent

Requirements

4”

(10 cm)

30”

(76.1 cm)

50”

(127 cm)

18”

(45.7 cm)

20”

(50.8 cm)

27”

(68.6 cm)

4”

(10 cm)

1”

(2.5 cm)

1”

(2.5 cm)

3”

(7.6 cm)

3”

(7.6 cm)

48 in

2

(310 cm

2

)

24 in

2

(155 cm

2

)

10

I N S TA L L AT I O N I N S T RU C T I O N S

INSTALLATION WITH OPTIONAL

PEDESTAL BASE OR STACKING KIT

IMPORTANT: If you are installing your dryer

using an optional pedestal base or stacking

kit, please refer to Optional Accessories in this

manual or to the instructions for your pedestal

or stacking kit before proceeding with the

installation.

Required Dimensions for Installation

With Pedestal

Required Dimensions for Installation

With Stacking Kit

OPTIONAL ACCESSORIES

For these and other LG products, contact your local LG dealer, or visit our Web site at ca.lge.com.

Pedestal (sold separately)

Stacking Kit (sold separately)

30”

(76.2 cm)

4”

(10 cm)

77

1

⁄

2

”

(190.5 cm)

1”

(2.5 cm)

1”

(2.5 cm)

27”

(68.6 cm)

11

I N S TA L L AT I O N I N S T RU C T I O N S

1 2

Hinge

Screws

Door

Latch

Latch Screws

Hinge

Screws

Latch

Screws

LEVELING THE DRYER

Use an adjustable wrench to turn the leveling

feet. Turn clockwise to raise the dryer or

counterclockwise to lower it. Raise or lower

the leveling feet until dryer is level from

side to side and front to back.

Make sure that all 4 leveling feet are in firm

contact with the floor.

REVERSING THE DOOR SWING

The swing of the dryer door can be reversed to fit your installation location.

Open the dryer door. Using a Phillips

screwdriver, remove the 2 screws that secure

the door hinge to the dryer door opening.

Remove the 4 screws from the latch side of the

dryer door opening, and remove the door latch.

Turn the door around so the hinge is

reversed, and reattach the door using the

2 screws previously removed. Reinstall the

door latch and the 4 screws.

Test the door swing to make sure the door

moves freely and latches securely.

2

• All four leveling feet must rest solidly on the

ﬂoor. Gently push on the top corners of the

dryer to make sure that the dryer does not

rock from corner to corner.

If you are installing the dryer on the optional

pedestal, you must use the leveling feet on the

pedestal to level the dryer. The dryer leveling feet

should be fully retracted.

Position the dryer in the final location. Place

a level across the top of the dryer.

1

Level

Leveling Feet

To ensure that the dryer provides optimal drying

performance, it must be level. To minimize

vibration, noise, and unwanted movement, the

floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as

necessary to level the dryer. Extending the

leveling feet more than necessary can cause

the dryer to vibrate.

WARNING

• Wear gloves during installation.

• Failure to follow these instructions can result in injury.

w

12

I N S TA L L AT I O N I N S T RU C T I O N S

CHANGING THE DRYER VENT LOCATION

Your new dryer is shipped to vent to the rear.

It can also be configured to vent to the bottom

or side (right-side venting is not available on

gas models).

An adapter kit, part number 383EEL9001B,

may be purchased from your LG retailer. This

kit contains the necessary duct components

to change the dryer vent location.

Remove the rear exhaust duct retaining

screw. Pull out the exhaust duct.

1

Press the tabs on the knockout and carefully

remove the knockout for the desired vent

opening (right-side venting is not available on

gas models). Press the adapter duct onto the

blower housing and secure to the base of the

dryer as shown.

2

Knockout

Bracket

Adapter

Duct

Preassemble a 4-in. (10 cm) elbow to the next

4-in. (10 cm) duct section, and secure all joints

with duct tape. Be sure that the male end of

the elbow faces AWAY from the dryer.

Insert the elbow/duct assembly through the

side opening and press it onto the adapter

duct. Secure in place with duct tape.

Be sure that the male end of the duct

protrudes 1½ in. (3.8 cm) to connect the

remaining ductwork.

Attach cover plate to the back of the dryer

with included screw.

1

/

2

"

(3.8 cm)

3

Elbow

Cover

Plate

1

Rear

Exhaust Duct

Retaining

Screw

OPTION 1: Side Venting

Press the adapter duct onto the blower

housing and secure to the base of the dryer

as shown.

2

Bracket

Adapter

Duct

Insert the 4-in. (10 cm) elbow through the

rear opening and press it onto the adapter

duct. Be sure that the male end of the elbow

faces down through hole in the bottom of the

dryer. Secure in place with duct tape.

Attach the cover plate to the back of the

dryer with included screw.

3

Elbow

Cover

Plate

OPTION 2: Bottom Venting

WARNING

w

• Use a heavy metal vent.

• Do not use plastic or thin foil duct.

• Clean old ducts before installing this dryer.

• Wear gloves during installation.

• Failure to follow these instructions can result in death

or ﬁre.

13

VENTING THE DRYER

• Do not crush or collapse ductwork. Failure

to follow these instructions can result in ﬁre

or death.

• Do not allow ductwork to rest on or

contact sharp objects. Failure to follow these

instructions can result in ﬁre or death.

• If connecting to existing ductwork, make

sure it is suitable and clean before installing

the dryer. Failure to follow these instructions

can result in ﬁre or death.

• Venting must conform to local building

codes. Failure to follow these instructions can

result in ﬁre or death.

• Gas dryers MUST exhaust to the outdoors.

Failure to follow these instructions can result

in ﬁre or death.

• Use only 4-in. (10 cm) rigid or ﬂexible metal

ductwork inside the dryer cabinet and

for venting outside. Failure to follow these

instructions can result in ﬁre or death.

• To reduce the risk of ﬁre, combustion, or

accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall,

ceiling, crawl space, chimney, gas vent, or

concealed space of a building. Failure to

follow these instructions can result in ﬁre

or death.

• To reduce the risk of ﬁre, DO NOT exhaust

the dryer with plastic or thin foil ducting.

Failure to follow these instructions can result

in ﬁre or death.

• The exhaust duct must be 4 in. (10 cm) in

diameter with no obstructions. The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before

installing your new dryer. Failure to follow

these instructions can result in ﬁre or death.

•

Rigid or semirigid metal ducting is

recommended for use between the dryer

and the wall. In special installations when

it is impossible to make a connection with

the above recommendations, a UL-listed

ﬂexible metal transition duct may be used

between the dryer and wall connection only.

The use of this ducting will affect drying

time. Failure to follow these instructions can

result in ﬁre or death.

• DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efﬁciency

of the exhaust system. Secure all joints

with duct tape. Failure to follow these

instructions can result in ﬁre or death.

• To maximize operating results, please

observe the duct length limitations noted in

the chart on page 15. Failure to follow these

instructions can result in ﬁre or death.

• Ductwork is not provided with the dryer.

You should obtain the necessary ductwork

locally. The end cap should have hinged

dampers to prevent backdraft when the

dryer is not in use. Failure to follow these

instructions can result in ﬁre or death.

I N S TA L L AT I O N I N S T RU C T I O N S

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

14

Routing and Connecting Ductwork

Follow the guidelines below to maximize drying

performance and reduce lint buildup and

condensation in the ductwork.

NOTE: Ductwork and fittings are NOT included

and must be purchased separately.

• Use 4-in. (10 cm) diameter rigid or semirigid

metal ductwork.

• The exhaust duct run should be as short as

possible.

• Use as few elbow joints as possible.

• The male end of each section of exhaust duct

must point away from the dryer.

• Use duct tape on all duct joints.

• Insulate ductwork that runs through unheated

areas in order to reduce condensation and lint

buildup on duct surfaces.

IMPORTANT: Failure to exhaust the dryer

correctly will void the dryer’s warranty.

VENTING THE DRYER (cont.)

Correct Venting

Incorrect Venting

I N S TA L L AT I O N I N S T RU C T I O N S

Number of Max. Length of 4-In. Dia. Max. Length of 4-In. Dia.

Wall Cap Type 90° Elbows Rigid Metal Duct Flexible Metal Duct

0 65 ft. (19.8 m) 45 ft. (13.7 m)

1 55 ft. (16.8 m) 35 ft. (10.7 m)

2 47 ft. (13.7 m) 30 ft. (9.1 m)

3 36 ft. (11.0 m) 25 ft. (7.6 m)

4 28 ft. (8.5 m) 20 ft. (6.1 m)

0 55 ft. (16.8 m) 35 ft. (10.7 m)

1 47 ft. (13.7 m) 27 ft. (8.1 m)

2 41 ft. (12.5 m) 21 ft. (6.4 m)

3 30 ft. (9.1 m) 17 ft. (5.2 m)

4 22 ft. (6.7 m) 15 ft. (4.5 m)

NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.

4"

(10.2 cm)

2

1

/2"

(6.35 cm)

4"

(10.2 cm)

Recommended

Use Only for Short

Run Installations

Ductwork

15

I N S TA L L AT I O N I N S T RU C T I O N S

Electrical Requirements for Gas Models Only

• Do not, under any circumstances, cut or

remove the third (ground) prong from the power

cord. Failure to follow this warning can result in

ﬁre, explosion, or death.

•

For personal safety, this dryer must be properly

grounded. Failure to follow this warning can result

in ﬁre, explosion, or death.

•

The power cord of this dryer is equipped with

a 3-prong (grounding) plug which mates with

a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock

hazard from this appliance. Failure to follow this

warning can result in ﬁre, explosion, or death.

•

This dryer must be plugged into a

120-VAC, 60-Hz. grounded outlet protected by

a 15-ampere fuse or circuit breaker. It is also

recommended that a separate circuit serving

only this dryer be provided. Failure to follow this

warning can result in ﬁre, explosion, or death.

•

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility

and obligation to have it replaced with a

properly grounded 3-prong wall outlet. Failure

to follow this warning can result in ﬁre, explosion,

or death.

16

CONNECTING GAS DRYERS

• Gas supply requirements:

As shipped from the factory, this dryer is

conﬁgured for use with natural gas. It can be

converted for use with LP (Liqueﬁed Propane)

gas. Gas pressure must not exceed 13 in.

water column.

•

A qualiﬁed service or gas company technician

must connect the dryer to the gas service.

Failure to do so can result in ﬁre, explosion,

or death.

•

Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve

during any pressure testing of the gas supply.

Failure to do so can result in ﬁre, explosion,

or death.

•

Supply line requirements:

Your laundry room must have a rigid gas

supply line to your dryer. In the United States,

an individual manual shutoff valve MUST be

installed within at least 6 ft. (1.8 m) of the dryer,

in accordance with the National Fuel Gas Code

ANSI Z223.1 or Canadian gas installation code

CSA B149.1. A 1/8-in. NPT pipe plug must

be installed. Failure to do so can result in ﬁre,

explosion, or death.

•

If using a rigid pipe, the rigid pipe should be

1/2-in. IPS. If acceptable under local codes

and ordinances and when acceptable to

your gas supplier, 3/8-in. approved tubing

may be used where lengths are less than

20 ft. (6.1 m). Larger tubing should be used

for lengths in excess of 20 ft. (6.1 m). Failure

to do so can result in ﬁre, explosion, or death.

•

Connect the dryer to the type of gas shown on

the nameplate. Failure to do so can result in ﬁre,

explosion, or death.

•

To prevent contamination of the gas valve,

purge the gas supply of air and sediment

before connecting the gas supply to the dryer.

Before tightening the connection between the

gas supply and the dryer, purge remaining air

until the odor of gas is detected. Failure to do

so can result in ﬁre, explosion, or death.

•

DO NOT use an open ﬂame to inspect for gas

leaks. Use a noncorrosive leak-detection ﬂuid.

Failure to do so can result in ﬁre, explosion,

or death.

•

Use only a new AGA- or CSA-certiﬁed gas

supply line with ﬂexible stainless steel

connectors. Failure to do so can result in ﬁre,

explosion, or death.

•

Securely tighten all gas connections. Failure

to do so can result in ﬁre, explosion, or death.

•

Use Teﬂon

®

tape or a pipe-joint compound that

is insoluble in Liqueﬁed Petroleum (LP) gas on

all pipe threads. Failure to do so can result in ﬁre,

explosion, or death.

•

DO NOT attempt any disassembly of the dryer;

any disassembly requires the attention and

tools of an authorized and qualiﬁed service

person or company. Failure to do so can result

in ﬁre, explosion, or death.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

I N S TA L L AT I O N I N S T RU C T I O N S

• Installation and service must be performed

by a qualiﬁed installer, service agency, or the

gas supplier. Failure to do so can result in ﬁre,

explosion, or death.

• Use only a new stainless steel ﬂexible

connector and a new AGA-certiﬁed

connector. Failure to do so can result in ﬁre,

explosion, or death.

• A gas shutoff valve must be installed within

6 ft. (1.8 m) of the dryer. Failure to do so can

result in ﬁre, explosion, or death.

• The dryer is conﬁgured for Natural Gas when

shipped from the factory. Make sure that the

dryer is equipped with the correct burner

nozzle for the type of gas being used (Natural

Gas or Liqueﬁed Petroleum). Failure to do so

can result in ﬁre, explosion, or death.

• If necessary, the correct nozzle (for the LP

nozzle kit order part number 4948EL4002B)

should be installed by a qualiﬁed technician

and the change should be noted on the dryer.

Failure to do so can result in ﬁre, explosion,

or death.

• All connections must be in accordance with

local codes and regulations. Failure to do so

can result in ﬁre, explosion, or death.

• Gas dryers MUST exhaust to the outdoors.

Failure to do so can result in ﬁre, explosion,

or death.

3/8" NPT Gas

Connection

Gas Supply

Shutoff Valve

Connecting the Gas Supply

Make sure that the gas supply to the laundry

room is turned OFF. Confirm that the type

of gas available in your laundry room is

appropriate for the dryer. The dryer is

prepared for Natural Gas with a 3/8-in. NPT

gas connection.

Remove the shipping cap from the gas

connection at the back of the dryer. Be

careful not to damage the threads of the gas

connector when removing the shipping cap.

Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel

connector with a 3/8-in. NPT fitting.

Securely tighten all connections between the

dryer and your laundry room’s gas supply.

Turn on your laundry room’s gas supply and

check all pipe connections (both internal and

external) for gas leaks with a noncorrosive

leak-detection fluid.

1

2

3

4

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for

elevations below 10,000 feet.

If your gas dryer is being installed at an elevation

above 10,000 feet, it must be derated by a

qualified technician or gas supplier.

Electrical Connection

Plug dryer into a

120-VAC, 60-Hz.

grounded 3-prong

outlet.

CONNECTING GAS DRYERS (cont.)

1/8" NPT Pipe

Plug

AGA/CSA-Certified

Stainless Steel

Flexible Connector

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

17

I N S TA L L AT I O N I N S T RU C T I O N S

18

Electrical Requirements for Electric Models Only

• This dryer must be connected to a grounded

metal, permanent wiring system, or an

equipment-grounding conductor must

be run with the circuit conductors and

connected to the equipment-grounding

terminal or lead on the dryer. Failure to do

so can result in ﬁre, explosion, or death.

• The dryer has its own terminal block that

must be connected to a separate 240 VAC,

60-Hertz, single-phase circuit, fused at 30

amperes (the circuit must be fused on both

sides of the line). ELECTRICAL SERVICE

FOR THE DRYER SHOULD BE OF THE

MAXIMUM RATE VOLTAGE LISTED ON THE

NAMEPLATE. DO NOT CONNECT DRYER TO

110-, 115-, OR 120-VOLT CIRCUIT. Heating

elements are available for ﬁeld installation

in dryers which are to be connected to an

electrical service of a different voltage than

that listed on the rating plate. Failure to follow

these instructions can result in ﬁre, explosion,

or death.

• If branch circuit to dryer is 15 ft. (4.5 m)

or less in length, use UL (Underwriters

Laboratories) listed No.-10 AWG wire

(copper wire only), or as required by local

codes. If over 15 ft. (4.50 m), use UL-listed

No.-8 AWG wire (copper wire only), or as

required by local codes. Allow sufﬁcient

slack in wiring so dryer can be moved from

its normal location when necessary. Failure

to do so can result in ﬁre, explosion, or death.

• The power cord (pigtail) connection between

wall receptacle and dryer terminal block

IS NOT supplied with dryer. Type of pigtail

and gauge of wire must conform to local

codes and with instructions on the following

pages. Failure to follow these instructions can

result in ﬁre, explosion, or death.

• A 4-wire connection is required for all mobile

and manufactured home installations, as

well as all new construction after January

1, 1996. A 4-wire connection must be used

where local codes do not permit grounding

through the neutral wire. Failure to do so can

result in ﬁre, explosion, or death.

Special Electrical Requirements for Mobile or Manufactured Homes

• Any installation in a manufactured or mobile

home must comply with the Manufactured

Home Construction and Safety Standards

Title 24 CFR, Part 32-80 or Standard CAN/

CSA0Z240 MH and local codes and ordinances.

• A 4-wire connection is required for all mobile

and manufactured home installations, as well

as all new construction after January 1, 1996.

Failure to do so can result in ﬁre, explosion,

or death.

CONNECTING ELECTRIC DRYERS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and

grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all

applicable local regulations. Please contact a qualified electrician to check your home’s wiring and

fuses to ensure that your home has adequate electrical power to operate the dryer.

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

wWARNING:

To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not modify the plug and internal wire

provided with the dryer.

• The dryer should be connected to 4-hole outlet.

• If it does not ﬁt the outlet, a proper outlet will

need to be installed by a qualiﬁed electrician.

Testing Dryer Heating

GAS MODELS

Close the dryer door, press the ON/OFF switch

to turn the dryer on, and start the dryer on a heat

setting. When the dryer starts, the igniter should

ignite the main burner.

NOTE: If all air is not purged from the gas line,

the gas igniter may turn off before the main

burner ignites. If this happens, the igniter will

reattempt gas ignition after approximately

two minutes.

ELECTRIC MODELS

Close the dryer door, press the ON/OFF switch

to turn the dryer on, and start the dryer on a heat

setting. The exhaust air should be warm after the

dryer has been operating for 3 minutes.

Checking Airflow

Effective dryer operation requires proper airflow.

The adequacy of the airflow can be measured

by evaluating the static pressure. Static pressure

in the exhaust duct can be measured with

a manometer, placed on the exhaust duct

approximately 2 ft. (60.9 cm) from the dryer.

Static pressure in the exhaust duct should not

exceed 0.6 in. (1.5 cm). The dryer should be

checked while the dryer is running with no load.

Checking Levelness

Once the dryer is in its final location, recheck

the dryer to be sure it is level. Make sure it is

level front to back and side to side, and that

all 4 leveling feet are firmly on the floor.

FINAL INSTALLATION CHECK

Once you have completed the installation of

the dryer and it is in its final location, confirm

proper operation with the following tests.

Any installation in a manufactured or mobile

home must comply with the Manufactured Home

Construction and Safety Standards Title 24 CFR,

Part 32-80 or Standard CAN/CSA0Z240 MH and

local codes and ordinances. If you are uncertain

whether your proposed installation will comply

with these standards, please contact a service

and installation professional for assistance.

• A gas dryer must be permanently attached to

the ﬂoor.

• The electrical connection for an electric dryer

must be a 4-wire connection. More detailed

information concerning the electrical connection

is provided in the section Connecting Electric

Dryers.

• To reduce the risk of combustion and ﬁre, the

dryer must be vented to the outside.

• DO NOT vent the dryer under a manufactured

home or mobile home.

• Electric dryers may be vented to the outside

using the back, left, right, or bottom panel.

• Gas dryers may be vented to the outside using

the back, left, or bottom panel. Gas dryers may

not be vented to the outside using the right side

panel because of the burner housing.

• The dryer exhaust duct must be afﬁxed securely

to the manufactured or mobile home structure,

and the exhaust duct must be made of a

material that will resist ﬁre and combustion.

It is recommended that you use a rigid or

ﬂexible metal duct.

• DO NOT connect the dryer exhaust duct

to any other duct, vent, chimney, or other

exhaust duct.

• Make sure the dryer has adequate access to

outside fresh air to ensure proper operation.

The opening for outside fresh air must be at

least 25 in

2

(163 cm

2

).

• It is important that the clearance of the duct

from any combustible construction be at least

2 in. (5 cm), and when venting the dryer to

the outdoors, the dryer can be installed with a

clearance of 1 in. (2.5 cm) at the sides and back

of the dryer.

• Please be aware that venting materials are

not supplied with the dryer. You should obtain

the venting materials necessary for proper

installation.

SPECIAL REQUIREMENTS FOR MANUFACTURED OR MOBILE HOMES

I N S TA L L AT I O N I N S T RU C T I O N S

19

• Check all pockets to make sure that they are

empty. Items such as clips, pens, coins, and

keys can damage both your dryer and your

clothes. Flammable objects such as lighters

or matches could ignite, causing a ﬁre.

Failure to do so can result in ﬁre, explosion,

or death.

• Never dry clothes that have been exposed to

oil, gasoline, or other ﬂammable substances.

Washing clothes will not completely remove

oil residues. Failure to obey this warning can

result in ﬁre, explosion, or death.

• Combine large and small items in a load.

• Damp clothes will expand as they dry. Do not

overload the dryer; clothes require room to

tumble dry properly.

• Close zippers, hooks, and drawstrings to

prevent these items from snagging or tangling

on other clothes.

H OW TO U S E

Tumble

dry

Dry

Normal

Permanent Press

/

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry

(used with

do not wash)

SORTING LOADS

Fabric Care Labels

Most articles of clothing feature fabric care labels

that include instructions for proper care.

Grouping Similar Items

For best results, sort clothes into loads that can

be dried with the same drying cycle.

Different fabrics have different care

requirements, and some fabrics will dry

more quickly than others.

Fabric Care Labels

Heat

setting

High

Medium

Low

No heat/air

CHECK THE LINT FILTER BEFORE EVERY LOAD

Always make sure the lint filter is clean before

starting a new load; a clogged lint filter will

increase drying times.

To clean, pull the lint filter straight up and roll any

lint off the filter with your fingers. Do not rinse or

wash the filter to remove lint. Push the lint filter

firmly back into place. See “Care and Cleaning”

for more information.

Always ensure the lint filter is properly installed

before running the dryer. Running the dryer with

a loose or missing lint filter may damage the

dryer and articles in the dryer.

Lint Filter

LOADING THE DRYER

Following are instructions for starting and using your new dryer. Please refer to specific sections of this

manual for more detailed information. Important Warning: To reduce the risk of fire, electric shock,

or injury to persons, read this entire manual, including the Important Safety Instructions, before

operating this dryer.

20

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

La page charge ...

LG RV1309AT Le manuel du propriétaire

Ce manuel convient également à

LG RV1309AT Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents