Snom M1 Quick Installation Guide

Catégorie
Des ponts
Taper
Quick Installation Guide
M1
DECT Repeater
Quick Installa on Guide
2
Important Safety Information
This symbol is to alert you to important operating or servicing instructions
that may appear on the product or in this user’s manual. Always follow
basic safety precautions when using this product to reduce the risk of
injury, re, or electric shock.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of re, electric shock and injury, including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water such as near a bathtub, wash bowl, kitchen
sink, laundry tub or swimming pool, or in a wet basement or shower.
5. Do not overload wall outlets and extension cords.
6. Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operation
instructions. Improper adjustment of other controls may result in damage
and often requires extensive work by an authorized technician to restore
the product to normal operation.
E. If the product has been dropped and the base unit and/or wireless mic has
been damaged.
F. If the product exhibits a distinct change in performance.
7. Do not place this product on an unstable table, shelf, stand or other unstable
surfaces.
8. Slots and openings in the back or bottom of the base unit are provided for
ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug.
This product should never be placed near or over a radiator or heat register.
3
This product should not be placed in any area where proper ventilation is not
provided.
9. This product should be operated only from the type of power source indicated
on the marking label.
10. Do not allow anything to rest on the power cord. Do not install this product
where the cord may be walked on.
11. Never push objects of any kind into this product through the slots in the base
unit or wireless mic because they may touch dangerous voltage points or create
a short circuit. Never spill liquid of any kind on the product.
12. Use only the adapter included with this product. Incorrect adapter polarity or
voltage can seriously damage the product.
13. For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
SAVE THESE INSTRUCTIONS
For cUL compliance only
Mesures de sécurité importantes
Ce symbole vous alertera d’informations importantes ou d’instructions
d’entretien pouvant apparaître dans ce guide d’utilisation. Respectez
toujours les mesures de sécurité et de sécurité de base lorsque vous
utilisez ce produit, an de réduire les risques de blessures, d’incendie, ou
d’électrocution.
Mesures de sécurité importantes
An de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de base lorsque vous utilisez votre
téléphone :
1. Lisez et comprenez bien toutes les instructions.
2. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
3. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez pas
de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chion doux et légèrement
humecté.
4
4. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo, d’un
évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-sol
humide ou sous la douche.
5. Ne surchargez pas les prises de courant et les rallonges.
6. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de Snom dans les cas suivants :
A. Lorsque le cordon d’alimentation est endommagé ou écorché.
B. Si du liquide a été échappé dans l’appareil.
C. Si l’appareil a été exposé à une source d’humidité telle que la pluie ou
l’eau.
D. Si le produit ne fonctionne pas normalement en respectant les instructions
de fonctionnement. Réglez uniquement les commandes indiquées dans
le les instructions de fonctionnement. Les réglages incorrects des autres
commandes pourraient provoquer un dommage qui pourrait exiger un
travail exhaustif de la part d’un technicien autorisé an de rétablir le
fonctionnement normal de l’appareil.
E. Si le produit a été échappé et que le socle et/ou le microphone sans l a
été endommagé.
F. Si le produit ache une nette diminution de sa performance.
7. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.
L’appareil pourrait tomber et être sérieusement endommagé.
8. Les ouvertures situées à l’arrière ou sous le socle servent à la ventilation.
An d’empêcher la surchaue, ces ouvertures ne doivent pas être obstruées
en plaçant l’appareil sur un lit, divan, tapis ou autre surface similaires. Ne
placez pas cet appareil à proximité d’un élément de chauage ni d’une plinthe
électrique. De plus, ne l’installez pas dans une unité murale ou un cabinet
fermé qui ne possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur les
étiquettes de l’appareil.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans
un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne
d’alimentation ni le cordon téléphonique modulaire.
11. N’enfoncez jamais d’objets dans les fentes du socle, car ceci risquerait d’entrer
en contact avec des points de tension dangereux ou provoquer un court-circuit.
N’échappez pas de liquides dans l’appareil.
5
12. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation d’un
adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager
sérieusement le produit et mettre votre sécurité en péril.
13. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise
de courant doit être installée près du produit, an d’assurer une accessibilité
sécuritaire à la prise de courant.
CONSERVEZ CES INSTRUCTIONS
6
FCC part 15
This device complies with Part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modications to this equipment not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
CAUTION: To maintain the compliance with the FCC’s RF exposure guideline, place the
base unit at least 20 cm from nearby persons.
7
Industry Canada
This Class B digital apparatus complies with Canadian requirements:
CAN ICES-3 (B)/NMB-3(B). Cet appareil numérique de la classe B est conforme à la
norme CAN ICES-3 (B)/NMB-3(B) du Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certication/registration number only signies that the Industry
Canada technical specications were met.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specications.
8
About this Guide
This Quick Start Guide provides you with basic installation and use instructions.
A limited set of features are described in abbreviated form.
For customer service or product information, visit our website at
snomamericas.com.
Introduction
The Repeater lets you extend the coverage area of your telephone system in all
directions, including up and down.
When registered to the Base Station, and the Repeater’s coverage area overlaps
the coverage area of the Base Station, the Base Station can hand o calls to the
Repeater as the user moves from one coverage area to another.
When connected to the Repeater, the cordless handset operates in exactly the same
way as it does when connected to the Base Station. The hand o from the
Base Station to the Repeater should be seamless, even during an active call.
Parts Checklist
Repeater
Power adapter
Quick Start Guide
9
Getting Started
Location
To get the best operating conditions for the Repeater, it is important to place it correctly.
Here are a few tips for placing the Repeater:
Place the Repeater as high as possible, but at least 6 feet (2 meters) o the ground.
Make sure you have good reception from the Base Station.
Make sure the location is close to a corresponding electrical outlet.
Never install electrical cords across a trac area; they can create a trip hazard or
become damaged and create a re or electrical hazard.
Allow at least 36 feet (11 meters) between Repeaters (if you are installing the
Repeaters across multiple oors, remember to allow 36 feet [11 meters] vertically as
well).
Avoid sources of electrical interference, such as hi- systems, oce equipment or
microwave ovens.
Avoid heat sources and direct sunlight.
Avoid things that can interfere with radio signals, such as metal doors, thick walls,
niches and cupboards.
Map the Base Station Coverage
To nd the best location for the Repeater, you need to determine the Base Station
coverage area.
1. Stand near the Base Station and make a call.
2. Walk away from the Base Station with the handset.
3. Make a note of where the signal becomes weaker.
NOTE: The optimum location for the Repeater is as far from the Base Station as possible
while still maintaining a “good” signal, or just inside the location where the signal became
weaker.
Test the Location
1. Register the Repeater to the Base Station.
See “Registration” on page 12.
2. Hold the Repeater in the place where you plan to mount it. The LED should remain
on and steady, indicating that the Repeater has a good signal from the Base Station.
10
Connect
Install your Repeater
Plug the AC adapter into the Repeater in its nal location, and then plug the other end into
the electrical outlet wall socket and switch the power on.
Or if you want to mount the Repeater on a wall:
Locking slot
Back view
Wall mount slot
1. Plug the AC adapter into the Repeater, thread the cable through the locking slot
(ensuring the cable does not protrude and prevent the unit from tting ush against
the wall) and then bundle the power cable with a twist tie.
2. Test the signal strength in the nal location as described in “Getting Started” on
page 9, and then install two wall-mount screws in the wall.
3. Put the wall mount slot on the back of the Repeater over the screw heads and slide
the Repeater down into place.
NOTE: Be sure the wall material can hold the weight of the Repeater.
Never install a Repeater in damaged or decaying wall material.
Electrical outlet
wall socket
AC adapter
Bottom view
11
Taihoon Kim | 22. Aug. 2018 | Revision 1.0CSP | VSP605
Silkscreen on the top
Pantone 8001C
illustration scale 100%
Setup Button Combined with LED Indicator
The setup button initiates the registration/deregistration process.
The LED indicator shows the link or usage status of the Repeater.
LED
Description
Colour Pattern
- - Powered o.
Red/Green Toggle The Repeater is in registration mode.
Green Triple Flash Registration is completed successfully.
Green Steady On Good link to the Base Station.
Yellow Steady On Weak link to the Base Station.
Red Slow Flash No link to the Base Station.
Green Double Flash The Repeater is in use with a good link to the Base
Station.
Yellow Double Flash The Repeater is in use with a weak link to the Base
Station.
Overview
Overview of the Repeater
LED Indicator
Setup button
12
Registration
Enable Repeater Mode on the SIP DECT Base Station:
Follow the instructions below to enable your Snom SIP DECT Base Station to connect
to the M1 DECT Repeater.
1. Open the Web User Interface (WebUI) for the SIP DECT Base Station.
2. Go to the System > Repeater Mode page.
3. Select the Enable Repeater Mode checkbox, and then click Save.
NOTE: Changing this setting will reboot your SIP DECT Base Station.
Register the Repeater to the SIP DECT Base Station:
Follow the instructions below to register the M1 DECT Repeater to your
Snom SIP DECT Base Station.
Make sure the Repeater is not connected to AC power before registering.
You can register up to ve Repeaters per Base Station.
1. Set the Base Station into registration mode: press the HANDSET LOCATOR
button for at least four seconds, and then release the button. Both LEDs on the
base station begin to ash.
2. Use the AC adapter to connect the Repeater to an electrical socket.
3. Press and hold the setup button for 5 seconds. The Repeater will start the
registration to the Base Station.
NOTE: The registration mode of the Repeater may last for 30 minutes.
Connect a Repeater to another Repeater in Cascade Mode:
You can connect up to two Repeaters in series between a Snom SIP DECT Base
Station and Handset. This connection is called Cascade Mode.
Follow the instructions below to connect two M1 DECT Repeaters in Cascade Mode.
1. Register all of your Repeaters to the Base Station (as described in “Register the
Repeater to the SIP DECT Base Station”, above).
2. Take one of the Repeaters to a location where it is far enough away from the
Base Station, but close to a Repeater to get a Cascade Mode connection.
3. Use the AC adapter to connect the Repeater to an electrical socket.
13
Troubleshooting
Problem Solutions
The LED on the Repeater
won’t stop ashing.
Move the Repeater closer to the Base Station.
Check for interference from electronic devices.
Make sure the Repeater is not too close to metal
objects or thick walls.
Calls will not hand over to
the Repeater.
Make sure the Repeater is within the Base Station’s
good signal range.
Make sure there are at least 11 meters between
Repeaters.
I used to be able to connect
to the Base Station, but now
I cannot.
Make sure the Repeater is powered on.
Move the Repeater closer to the Base Station and
register it again.
The audio quality is
very poor or noisy when
receiving a call.
The signal connection is very poor. Try to nd another
location where the signal to the Base Station is better.
Calls lost or audio becomes
poor when moving from
the Base Station reception
range to the Repeater
reception range.
You may be moving out of the Base Station or
Repeater reception range, or are in a blind spot. Move
towards the Base Station or Repeater.
14
Technical Specications
Standards Digital Enhanced Cordless Telecommunication (DECT)
RF Frequency Band 1921.536–1928.448 MHz
Number of Channels 5
AC Adapter Output Voltage 6.0V DC 450mA
15
Disposal Warning
1. When this crossed-out wheeled bin symbol is attached to a product, it
means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products/battery should be disposed of
separately from the municipal waste stream via designated collection
facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance/battery will help prevent
potential negative consequences for the environment and human
health.
For more detailed information about disposal of your old appliance/battery, please
contact your city oce, waste disposal service or the shop where you purchased the
product.
VTECH COMMUNICATIONS, INC.
Tigard, Oregon 97223, USA.
Copyright © 2019 Snom Technology GmbH. All Rights Reserved.
Specications are subject to change without notice.
v2019001 Version 1, 07/19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Snom M1 Quick Installation Guide

Catégorie
Des ponts
Taper
Quick Installation Guide

dans d''autres langues