Zanussi ZWSH7100VS Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
• Do not let children play with the appliance.
• Children aged 3 years and under must be kept away from this
appliance when it is in operation at all times.
• Keep all packaging away from children and dispose of it
appropriately.
• Keep detergents away from children.
• Keep children and pets away from the appliance door when it is
open.
• Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
• Do not change the specification of this appliance.
• Do not exceed the maximum load of 7 kg (refer to the
"Programme chart" chapter).
• The operating water pressure at the water entry point from the
outlet connection must be between 0.5 bar (0.05 MPa) and 8
bar (0.8 MPa).
• The ventilation opening in the base (if applicable) must not be
covered by a carpet, mat, or any floor covering.
• The appliance must be connected to the water mains using the
new supplied hose sets, or other new hose sets supplied by
the Authorised Service Centre.
2
• Old hose sets must not be reused.
• If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
• Before any maintenance operation, deactivate the appliance
and disconnect the mains plug from the socket.
• Do not use high pressure water sprays and/or steam to clean
the appliance.
• Clean the appliance with a moist cloth. Use only neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
SAFETY INSTRUCTIONS
INSTALLATION
• Remove all the packaging and the transit bolts.
• Keep the transit bolts in a safe place. If the
appliance is to be moved in future they must be
reattached to lock the drum to prevent internal
damage.
• Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
• Do not install or use a damaged appliance.
• Follow the installation instruction supplied with
the appliance.
• Do not install or use the appliance where the
temperature can be less than 0°C or where it is
exposed to the weather.
• The floor area where the appliance is to be
installed must be flat, stable, heat resistant and
clean.
• Make sure that there is air circulation between
the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the flooring.
• Do not install the appliance where the appliance
door cannot be fully opened.
• Do not put a container to collect possible water
leakage under the appliance. Contact the
Authorised Service Centre to ensure which
accessories can be used.
ELECTRICAL CONNECTION
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the electrical information on the
rating plate agrees with the power supply. If not,
contact an electrician.
• Do not use multi-plug adapters and extension
cables.
• Make sure not to cause damage to the mains
plug and to the mains cable. Should the mains
cable need to be replaced, this must be carried
out by our Authorised Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
• Do not touch the mains cable or the mains plug
with wet hands.
• Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
• This appliance complies with the E.E.C.
Directives.
WATER CONNECTION
• Do not cause damage to the water hoses.
• Before connection to new pipes, pipes not used
for a long time, where repair work has been
carried out or new devices fitted (water meters,
etc.), let the water flow until it is clean and clear.
• Ensure that there are no visible water leaks
during and after the first use of the appliance.
USE
WARNING! Risk of injury, electrical
shock, fire, burns or damage to the
appliance.
• This appliance is for household use only.
• Follow the safety instructions on the detergent
packaging.
3
• Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
• Make sure that all metal objects are removed
from the laundry.
• Do not touch the glass door while a programme
is in operation. The glass can get hot.
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
WARNING! Risk of injury or
suffocation.
• Disconnect the appliance from the mains
electrical and water supplies.
• Cut off the mains electrical cable close to the
appliance and dispose of it.
• Remove the door catch to prevent children or
pets from becoming trapped in the drum.
• Dispose of the appliance in accordance with
local requirements for the disposal of Waste
Electrical and Electronic Equipment (WEEE).
PRODUCT DESCRIPTION
APPLIANCE OVERVIEW
1
2
3
5
6
7
4
1
Worktop
2
Detergent dispenser
3
Control panel
4
Rating plate
5
Door handle
6
Drain pump filter
7
Feet for levelling the appliance
4
CONTROL PANEL
CONTROL PANEL DESCRIPTION
Temperature
Rinse
Hold
Spin
Extra
Rinse
Start/Pause
Synthetics
Wool
/
Handwash
Cotton
+ Prewash
Cotton Eco
Rinse
Drain
Spin
5 shirts
Mini 30
Easy Iron
Jeans
CottonSpecial
Delicates
Mix 20°
90°
60°
40°
30°
1000
900
700
Delay Start
Quick
Wash
5678910
2 3 41
1
Programme knob
2
Display
3
Delay Start button (Delay Start)
4
Door locked indicator
5
Start/Pause button (Start/Pause)
6
Extra Rinse button (Extra Rinse)
7
Super quick button (Quick Wash)
8
Rinse Hold button (Rinse Hold)
9
Spin reduction button (Spin)
10
Temperature button (Temperature)
DISPLAY
A CB
The display shows:
A. The delay start .
When you press the delay start button, the
display shows the delay start time.
B. The child lock indicator.
The indicator comes on the display when the
related option is set.
C. This area shows:
• The programme time.
• The alarm codes.
If the appliance has a malfunction, the
display shows the alarm codes. Refer to the
chapter 'Troubleshooting' .
• The display shows the message for
some seconds if:
5
– You set a option that is not suitable for
the programme.
– You change the programme while it
operates.
PROGRAMMES
PROGRAMME CHART
Programme
Temperature range
Maximum load
Maximum spin speed
Programme description
(Type of load and soil level)
Washing programmes
Cotton
90°C - (Cold)
7 kg
1000 rpm
White cotton and coloured cotton. Nor-
mal soil and light soil.
Cotton+Prewash
90°C - (Cold)
7 kg
1000 rpm
White cotton and coloured cotton.
Heavy soil and normal soil.
Cotton Eco
60°C - 40°C
7 kg
1000 rpm
White cotton and fast-coloured cotton.
Normal soil. The energy consumption de-
creases and the time of the washing pro-
gramme is extended
1)
.
Synthetics
60°C - (Cold)
3 kg
1000 rpm
Synthetic items or mixed fabric items.
Normal soil.
Mix 20°
20°C
3 kg
1000 rpm
Special programme for cotton, synthetic and
mixed fabrics lightly soiled. Select this pro-
gramme to reduce the energy consumption.
Make sure that the detergent is suitable for
low temperatures in order to have good
washing results
2)
.
Delicates
40°C - (Cold)
3 kg
700 rpm
Delicate fabrics such as acrylics, vis-
cose, polyester items. Normal soil.
Wool/Handwash
40°C - (Cold)
1.5 kg
1000 rpm
Machine washable wool, hand washa-
ble wool and delicate fabrics with «hand
washing» care symbol.
3)
Rinse
Cold
7 kg
1000 rpm
To rinse and spin the laundry. All fabrics,
except woollens and very delicate fabrics.
Reduce the spin speed accordingly to the
type of laundry.
6
Programme
Temperature range
Maximum load
Maximum spin speed
Programme description
(Type of load and soil level)
Drain
7 kg To drain the water in the drum. All fabrics.
Spin
7 kg
1000 rpm
To spin the laundry and to drain the water in
the drum. All fabrics, except woollens
and delicate fabrics.
Easy Iron
60°C - (Cold)
1.5 kg
900 rpm
Synthetic items requiring a gentle
wash. Normal and light soil.
4)
5 shirts
30°C
900 rpm Synthetic and mixed fabric items. Light
soil items and items to freshen up. For 5 - 6
shirts.
Mini 30
30°C
3 kg
700 rpm
Synthetic and delicate items. Light soil
items or items to refresh.
Jeans
60°C - (Cold)
7 kg
1000 rpm
Items in denim and jersey. Also for dark
coloured items.
1) Cottons energy saving programme. This programme at 60ºC with a load of 7 kg is the reference pro-
gramme for data entered in the energy label, in compliance with EU Commission Directive 95/12/EC,
measured according to EN 60456/2005. Set this programme to have a good washing results and de-
crease the energy consumption. The washing programme time is extended.
2) The appliance performs the short heating phase if the water temperature is below 20°C. The appliance
can show the temperature setting as “cold”.
3) During this cycle the drum rotates slowly to ensure a gentle wash. It can seem that the drum doesn't
rotate or doesn't rotate properly, but this is normal for this programme.
4) To reduce creasing, this cycle regulates the water temperature and performs a soft wash and spin
phase. The appliance adds some rinses.
Programme options compatibility
Programme
Spin
Rinse Hold
Quick Wash
1)
Extra Rinse
2)
Delay Start
Cotton
■ ■ ■ ■ ■
7
Programme
Spin
Rinse Hold
Quick Wash
1)
Extra Rinse
2)
Delay Start
Cotton+Prewash
■ ■ ■ ■ ■
Cotton Eco
■ ■ ■ ■
Synthetics
■ ■ ■ ■ ■
Mix 20°
■ ■ ■ ■
Delicates
■ ■ ■ ■
Wool/Handwash
■ ■ ■
Rinse
■ ■ ■ ■
Drain
Spin
■ ■
Easy Iron
■ ■ ■ ■
5 shirts
■ ■
Mini 30
■
Jeans
■ ■ ■ ■
1) If you set the shortest duration, we recommend that you decrease the load size. It is possible to fully
load the appliance, however the washing results can be less satisfactory.
2) If you set Extra Rinse option, the appliance adds some additional rinses. In the Rinse programme, if you
set a low spin speed the appliance performs delicate rinses and a short spin.
CONSUMPTION VALUES
The data in this table are approximate. Different variables can affect the data: the quantity
and type of laundry, the water and ambient temperature.
8
Programmes Load (kg)
Energy con-
sumption
(kWh)
Water con-
sumption (litre)
Approximate pro-
gramme duration (mi-
nutes)
Cottons 60°C 7 1.30 61 200
Cotton Energy Saving Pro-
gramme 60°C
1)
7 0.90 46 223
Cottons 40°C 7 1.00 61 186
Synthetics 40°C 3 0.65 58 125
Delicates 40°C 3 0.53 47 55
Wool/Handwash 30°C 1.5 0.45 59 69
1) «Cotton Energy Saving programme » at 60°C with a load of 7 kg is the reference programme for the
data entered in the energy label, in compliance with EU Commission Directive 95/12/EC and measured
according to EN 60456/2005.
Off Mode (W) Left On Mode (W)
0,48 0,48
The information given in the chart above is compliant with the EU Commission regulation 1015/2010
implementing directive 2009/125/EC
OPTIONS
TEMPERATURE
With this option you can change the default
temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
SPIN
With this option you can change the default spin
speed.
The indicator of the set speed comes on.
RINSE HOLD
• Set this option to prevent the laundry creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the laundry
creases.
• The door stays locked. You must drain the water
to unlock the door.
To drain the water refer to ‘At the end
of the programme’.
QUICK WASH
Press this button to decrease the programme
duration.
Set this option for items with light soil or items to
refresh.
EXTRA RINSE
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to detergents
and in areas where the water is soft.
The related indicator comes on.
DELAY START
With this option you can delay the start of a
programme from 30 minutes to 20 hours.
The display shows the related indicator.
9
DOOR LOCKED INDICATOR
The indicator shows when the door can be
opened:
• The indicator is on: the door cannot be opened.
• The indicator flashes: the door is opening in
some minutes.
• The indicator is off: the door can be opened.
SETTINGS
CHILD LOCK
With this option you can prevent that the children
play with the control panel.
• To activate/deactivate this option, press
Temperature and Spin at the same time until the
indicator comes on/goes off.
You can activate this option:
• After you press Start/Pause: the options and the
programme knob are locked.
• Before you press Start/Pause: the appliance
cannot start.
ACOUSTIC SIGNALS
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
press Rinse Hold and Quick Wash at the same
time for 6 seconds.
If you deactivate the acoustic signals,
they continue to operate when the
appliance has a malfunction.
PERMANENT EXTRA RINSE
With this option you can permanently have an extra
rinse when you set a new programme.
• To activate/deactivate this option touch the
buttons Rinse Hold and Extra Rinse at the same
time until the indicator of Extra Rinse button
comes on/goes off.
BEFORE FIRST USE
1. Put 2 litre of water in the detergent
compartment for washing phase.
This activates the drain system.
2. Put a small quantity of detergent in the
compartment for washing phase.
3. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and the
tub.
DAILY USE
WARNING! Refer to Safety chapters.
LOADING THE LAUNDRY
Open the water tap. Connect the mains plug to the
mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a time.
3. Shake the items before you put them in the
appliance.
Make sure not to put too much laundry in the drum.
Refer to max. loads indicated in "Programme chart".
4. Close the door.
CAUTION!
Make sure
that no laun-
dry stays be-
tween the
seal and the
door. There
is a risk of
water leak-
age or dam-
age to the
laundry.
10
USING DETERGENT AND ADDITIVES
2
1
1. Measure out the de-
tergent and the fabric
conditioner.
2. Put the detergent
and the fabric condi-
tioner into the com-
partments.
3. Carefully close the
detergent drawer.
DETERGENT COMPARTMENTS
CAUTION! Use only specified
detergents for washing machine.
Always obey the instructions that you
find on the packaging of the detergent
products.
1 Detergent compartment for prewash
phase or soak programme (if availa-
ble). Add the detergent for prewash
and soak before the start of the pro-
gramme.
2 Detergent compartment for washing
phase. If you use a liquid detergent,
put it immediately before you start
the programme.
Compartment for liquid additives
(fabric conditioner, starch). Put the
product in the compartment before
you start the programme.
LIQUID OR POWDER DETERGENT
Pull out the detergent
dispenser until it stops.
A
2 1
The position A of the de-
tergent divider is for
powder detergent.
A
To use also liquid de-
tergent/additive or
bleach:
Remove detergent divider
from the position A.
B
Insert the detergent divid-
er in position B.
2 1
B
The position B of the de-
tergent divider is for pow-
der detergent in the rear
compartment and for liq-
uid detergent/additive or
bleach in the front com-
partment.
C
To use only liquid de-
tergent:
Insert the detergent divid-
er in position C.
11
2 1
C
The position C of the de-
tergent divider is for liq-
uid detergent.
Close the detergent dis-
penser carefully.
When you use the liquid detergent:
• Do not use gelatinous or thick liq-
uid detergents.
• Do not put more liquid detergent
than the edge of the detergent de-
vider.
• Do not set the prewash option.
• Do not set the delay start.
SETTING A PROGRAMME
1. Turn the programme knob to switch the
appliance on and set the programme:
• The indicator of the button Start/Pause
flashes.
• The display shows the programme duration.
2. If necessary, change the temperature and the
spin speed or add available options. When you
activate an option, the indicator of the set
option comes on.
If you set something incorrect, the
display shows the message .
STARTING A PROGRAMME WITHOUT THE
DELAY START
Press the button Start/Pause.
• The indicator of the button Start/Pause
stops to flash and stays on.
• The programme starts, the door locks, the
indicator is on.
• The programme time decreases with steps
of one minute.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
STARTING A PROGRAMME WITH THE DELAY
START OPTION
1. Press the button Delay Start again and again
until the display shows the delay you want to
set. The delay start indicator comes on.
2. Press the button Start/Pause:
• The door is locked and the indicator is
on.
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the Delay Start option before you
press the button Start/Pause. After
pressing the button Start/Pause you
can only cancel the Delay Start option.
To cancel the Delay Start option:
a. Press the button Start/Pause to set the
appliance to pause. The indicator of button
Start/Pause flashes.
b. Press the button Delay Start until the
display shows .
Press the button Start/Pause again to start
the programme immediately.
CANCELLING A RUNNING PROGRAMME
1. Turn the programme knob to position to
cancel the programme and to deactivate the
appliance.
2. Turn the programme knob again to activate the
appliance. Now, you can set a new washing
programme.
Before starting the new programme
the appliance could drain the water. In
this case, make sure that the detergent
is still in the detergent compartment, if
not fill the detergent again.
INTERRUPTING A PROGRAMME AND
CHANGING THE OPTIONS
You can change only some options before they
operate.
1. Press the button Start/Pause.
The indicator flashes.
2. Change the options.
3. Press the button Start/Pause again.
The programme continues.
12
OPENING THE DOOR
While a programme or the Delay Start operates, the
appliance door is locked. The indicator is on.
CAUTION! If the temperature and
level of the water in the drum are too
high and the drum still rotates, you
cannot open the door.
To open the door during the first minutes of the
cycle or when the Delay Start operates:
1. Press the button Start/Pause to pause the
appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button Start/
Pause again. The programme (or the Delay
Start) continues.
AT THE END OF THE PROGRAMME
• The appliance stops automatically.
• The acoustic signal operates (if it is activated).
• In the display comes on.
• The indicator of the button Start/Pause goes off.
• The door lock indicator goes off.
Turn the programme knob to position to
deactivate the appliance.
• You can open the door.
• Remove the laundry from the appliance. Make
sure that the drum is empty.
• Close the water tap.
• Keep the door and the detergent drawer ajar, to
prevent the mildew and odours.
The washing programme is completed, but
there is water in the drum:
• The drum turns regularly to prevent the creases
in the laundry.
• The indicator Rinse Hold stays on to remind you
to drain the water.
• The door lock indicator is on. The indicator
of button Start/Pause flashes. The door stays
locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Set a Drain or a Spin programme.
• Press the button Start/Pause. The
appliance drains the water and spins.
2. When the programme is completed and the
door lock indicator goes off, you can open
the door.
3. Turn the programme knob to the position to
deactivate the appliance.
STAND BY
Some minutes after the end of the washing
programme, if you do not deactivate the appliance,
the energy saving status activates. The energy
saving status decreases the energy consumption
when the appliance is on the standby:
• All indicators and the display go off.
• The indicator of button Start flashes slowly.
Press one of the buttons to deactivate the energy
saving status.
HINTS AND TIPS
THE LAUNDRY LOAD
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on the
laundry care labels.
• Do not wash white and coloured items together.
• Some coloured items can discolour with the first
wash. We recommend that you wash them
separately for the first times.
• Button up pillowcases, close zippers, hooks and
poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn multilayered fabrics, wool and items with
painted illustrations inside out.
• Remove hard stains.
• Wash heavy soil stains with a special detergent.
• Be careful with the curtains. Remove the hooks
and put the curtains in a washing bag or
pillowcase.
• Do not wash laundry without hems or with cuts.
Use a washing bag to wash small and/or
delicate items (e.g. underwired bras, belts,
tights, etc. ).
• A very small load can cause balance problems
with the spin phase. If this occurs, adjust
manually the items in the tub and start the spin
phase again.
STUBBORN STAINS
For some stains, water and detergent is not
sufficient.
We recommend that you pre-treat these stains
before you put the items in the appliance.
13
Special stain removers are available. Use the
special stain remover that is applicable to the type
of stain and fabric.
DETERGENTS AND ADDITIVES
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics (40
°C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C max)
for all types of fabric, or special for woollens
only.
• Do not mix different types of detergents.
• To help the environment, do not use more than
the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and colour
of the fabric, the programme temperature and
the level of soil.
• If your appliance does not have the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by the
detergent's manufacturer).
ECOLOGICAL HINTS
• Set a programme without the prewash phase to
wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry allowed.
• If necessary, use a stain remover when you set a
programme with a low temperature.
• To use the correct quantity of detergent, check
the water hardness of your domestic system.
Refer to "Water hardness".
WATER HARDNESS
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where the
water hardness is soft it is not necessary to use a
water softener.
To know the water hardness in your area, contact
your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
CARE AND CLEANING
WARNING! Refer to Safety chapters.
EXTERNAL CLEANING
Clean the appliance with soap and warm water
only. Fully dry all the surfaces.
CAUTION! Do not use alcohol,
solvents or chemical products.
DESCALING
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special products
for washing machines. Do this separately from the
laundry wash.
Always obey the instructions that you
find on the packaging of the product.
MAINTENANCE WASH
With the low temperature programmes it is possible
that some detergent stays in the drum. Perform a
maintenance wash regularly. To do this:
• Remove all laundry from the drum.
• Select the cotton programme with the highest
temperature with a small quantity of detergent.
DOOR SEAL
Regularly examine the
seal and remove all ob-
jects from the inner part.
14
CLEANING THE DETERGENT DISPENSER
1 2 3 4
5 6
CLEANING THE DRAIN FILTER
1 2 3 4
1
2
5 6 7 8
1
2
9 10
15
CLEANING THE INLET HOSE AND THE VALVE
FILTER
1.
1
2
3
2.
3.
4.
45°
20°
EMERGENCY DRAIN
Because of a malfunction, the appliance cannot
drain the water.
If this occurs, do steps (1) through (10) of
'Cleaning the drain filter'. If necessary, clean the
pump.
When you drain the water with the emergency drain
procedure, you must activate again the drain
system:
1. When you drain the water with the emergency
drain procedure, you must activate again the
drain system: Put 2 litres of water in the main
wash compartment of the detergent dispenser.
2. Start the programme to drain the water
FROST PRECAUTIONS
If the appliance is installed in an area where the
temperature can be less than 0° C, remove the
remaining water from the inlet hose and the drain
pump.
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Put the two ends of the inlet hose in a
container and let the water flow out of the
hose.
4. Empty the drain pump. Refer to the emergency
drain procedure.
5. When the drain pump is empty, install the inlet
hose again.
WARNING! Make sure that the
temperature is higher than 0 °C before
you use the appliance again.
The manufacturer is not responsible
for damages caused by low
temperatures.
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
INTRODUCTION
The appliance does not start or it stops during
operation.
First try to find a solution to the problem (refer to
the table). If the problem persists, contact the
Authorised Service Centre.
With some problems, the acoustic signals
operate and the display shows an alarm
code:
•
- The appliance does not fill with water
properly.
• - The appliance does not drain the water.
• - The appliance door is open or not
closed correctly. Please check the door!
• - The mains supply is unstable. Wait until
the mains supply is stable.
16
• - No communication between electronic
elements of the appliance. Switch off and
switch on again.
WARNING! Deactivate the appliance
before you do the checks.
POSSIBLE FAILURES
Problem Possible solution
The programme does not
start.
• Make sure that the mains plug is connected to the mains socket.
• Make sure that the appliance door is closed.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of
countdown.
• Deactivate the Child Lock function if it is on (if available).
The appliance does not fill
with water properly.
• Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter of the inlet hose and the filter of the valve
are not clogged. Refer to “Care and cleaning”.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is correct.
The appliance does not
drain the water.
• Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the drain filter is not clogged. Clean the filter, if nec-
essary. Refer to 'Care and cleaning'.
• Make sure that the drain hose is in the correct position. The hose
may be too low.
• Set the drain programme if you set a programme without drain
phase.
• Set the drain programme if you set an option which ends with water
in the tub.
The spin phase does not
operate or the washing cy-
cle lasts longer than usual-
ly.
• Set the spin programme.
• Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
There is water on the floor. • Make sure that the couplings of the water hoses are tight and there
is not water leakages.
• Make sure that the drain hose have no damages.
• Make sure you use the correct detergent and the correct quantity of
it.
You cannot open the appli-
ance door.
• Make sure that the washing programme is finished.
• Set the drain or the spin programme if there is water in the drum.
The appliance makes an
unusual noise.
• Make sure the levelling of the appliance is correct. Refer to 'Installa-
tion'.
• Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation'.
• Add more laundry in the drum. The load may be too small.
17
Problem Possible solution
The washing results are
not satisfactory.
• Increase the detergent quantity or use a different detergent.
• Use special products to remove the stubborn stains before you
wash the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
You cannot set an option. • Make sure that you press only the wanted button(s).
After the check, activate the appliance. The
programme continues from the point of interruption.
If the problem occurs again, contact the Authorised
Service Centre.
If the display shows other alarm codes. Deactivate
and activate the appliance. If the problem
continues, contact the Service.
SERVICE
We recommend the use of original spare parts.
When contacting the Authorised Service Centre,
make sure that these data are available. You can
find the information on the rating plate: model, PNC
and Serial Number. (Mod., Prod. No., Ser. No.)
TECHNICAL DATA
Dimension Width/ Height/ Depth/ To-
tal depth
595 mm / 850 mm / 450 mm / 490 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
230 V
2200 W
10 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where
the low voltage equipment has no protection against
moisture
IPX4
Water supply pressure Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Water supply
1) Cold water
Maximum Load Cotton 7 kg
Energy Efficiency Class A++
Spin Speed Maximum 1000 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol . Put the
packaging in applicable containers to recycle it.
Help protect the environment and human health
and to recycle waste of electrical and electronic
appliances. Do not dispose appliances marked with
the symbol with the household waste. Return the
product to your local recycling facility or contact
your municipal office.
18
INFORMATIONS DE SÉCURITÉ
Avant d'installer et d'utiliser cet appareil, lisez soigneusement les
instructions fournies. Le fabricant ne pourra être tenu pour
responsable des blessures et dégâts résultant d'une mauvaise
installation ou utilisation. Conservez toujours les instructions dans
un lieu sûr et accessible pour vous y référer ultérieurement.
SÉCURITÉ DES ENFANTS ET DES PERSONNES
VULNÉRABLES
• Cet appareil peut être utilisé par des enfants de plus de 8 ans,
ainsi que des personnes dont les capacités physiques,
sensorielles et mentales sont réduites ou dont les
connaissances et l'expérience sont insuffisantes, à condition
d'être surveillés ou d'avoir reçu des instructions concernant
l'utilisation sécurisée de l'appareil et de comprendre les risques
encourus.
• Ne laissez pas les enfants jouer avec l'appareil.
• Les enfants de moins de 3 ans doivent être tenus éloignés de
l'appareil en permanence lorsqu'il est en fonctionnement.
• Ne laissez pas les emballages à la portée des enfants et jetez-
les convenablement.
• Ne laissez pas les détergents à la portée des enfants.
• Tenez les enfants et les animaux éloignés du hublot de
l'appareil lorsque celui-ci est ouvert.
• Les enfants ne doivent pas nettoyer ni entreprendre une
opération de maintenance sur l'appareil sans surveillance.
SÉCURITÉ GÉNÉRALE
• Ne modifiez pas les caractéristiques de cet appareil.
• Respectez la charge maximale de 7 kg (reportez-vous au
chapitre « Tableau des programmes »).
• La pression de l'eau en service au niveau du point d'entrée en
provenance de l'arrivée d'eau doit être comprise entre 0,5 bar
(0,05 MPa) et 8 bar (0,8 MPa).
19
• Les orifices d'aération situés à la base (si présents) ne doivent
pas être obstrués par de la moquette, un tapis, ou tout type de
revêtement de sol.
• L'appareil doit être raccordé à l'arrivée d'eau à l'aide des tuyaux
neufs fournis, ou d'autres tuyaux neufs fournis par le service
après-vente agréé.
• N'utilisez pas de tuyaux provenant d'anciens appareils.
• Si le câble d'alimentation est endommagé, il doit être remplacé
par le fabricant, un service de maintenance agréé ou un
technicien qualifié afin d'éviter tout danger lié à l'électricité.
• Avant toute opération d'entretien, éteignez l'appareil et
débranchez la fiche de la prise secteur.
• Ne pulvérisez pas d'eau ni de vapeur à haute pression pour
nettoyer l'appareil.
• Nettoyez l'appareil avec un chiffon humide. Utilisez uniquement
des produits de lavage neutres. N'utilisez pas de produits
abrasifs, de tampons à récurer, de solvants ni d'objets
métalliques.
CONSIGNES DE SÉCURITÉ
INSTALLATION
• Retirez l'intégralité de l'emballage et les boulons
de transport.
• Conservez les boulons de transport en lieu sûr.
Si l'appareil doit être de nouveau déplacé, les
boulons doivent être réutilisés pour maintenir le
tambour en place et éviter tout dégât interne.
• Soyez toujours vigilants lorsque vous déplacez
l'appareil car il est lourd. Utilisez toujours des
gants de sécurité et des chaussures fermées.
• N'installez pas et ne branchez pas un appareil
endommagé.
• Suivez scrupuleusement les instructions
d'installation fournies avec l'appareil.
• N'installez pas l'appareil ou ne l'utilisez pas dans
un endroit où la température ambiante est
inférieure à 0 °C ou dans un endroit exposé aux
intempéries.
• L'appareil doit être installé sur un sol plat,
stable, résistant à la chaleur et propre.
• Assurez-vous que de l'air circule entre l'appareil
et le sol.
• Réglez les pieds pour laisser un espace
suffisant entre l'appareil et le sol.
• N'installez pas l'appareil dans un endroit où il ne
pourrait pas être complètement ouvert.
• Ne placez aucun récipient sous l'appareil pour
récupérer tout éventuel écoulement. Contactez
le service après-vente agréé pour connaître les
accessoires disponibles.
BRANCHEMENT ÉLECTRIQUE
• L'appareil doit être relié à la terre.
• Utilisez toujours une prise de courant de
sécurité correctement installée.
• Vérifiez que les données électriques figurant sur
la plaque signalétique correspondent à celles
de votre réseau. Si ce n'est pas le cas,
contactez un électricien.
• N'utilisez pas d'adaptateurs multiprises ni de
rallonges.
• Veillez à ne pas endommager la fiche secteur ni
le câble d'alimentation. Le remplacement du
cordon d'alimentation de l'appareil doit être
effectué par notre service après-vente agréé.
• Ne branchez la fiche d'alimentation à la prise de
courant qu'à la fin de l'installation. Assurez-vous
que la prise de courant est accessible une fois
l'appareil installé.
20
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Zanussi ZWSH7100VS Manuel utilisateur
- Catégorie
- Machines à laver
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Zanussi ZWSH7100VS User manual