Hotpoint HDA2100HBB Guide d'installation

Marque: Hotpoint

Modèle: HDA2100HBB

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Installation Instructions

Built-In & Spacemaker

Dishwashers

If you have questions, call GE Appliances at 800.GE.CARES (800.432.2737) or visit our website

at: GEAppliances.com. In Canada, please call 800.561.3344 or visit geappliances.ca

READ CAREFULLY

KEEP THESE INSTRUCTIONS

CHECK THE FOLLOWING

Dishwasher is square and level at both the top and

bottom of the cabinet opening, with no twisting or

distortion of the tub or door

All 4 legs of the dishwasher are firmly in contact with the

floor

Drain hose is not pinched between the dishwasher and

adjacent cabinets or walls

FOR YOUR SAFETY

Read and observe all WARNINGS and CAUTIONS

shown throughout these instructions.

While performing installations described in this

booklet, gloves, safety glasses or goggles should

be worn.

IMPORTANT – Observe all governing codes and

ordinances.

• Note to Installer – Be sure to leave these instructions

for the consumer’s and local inspector’s use.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

• Skill Level – Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills.

Proper installation is the responsibility of the

installer. Product failure due to improper installation

is not covered under the GE Appliances Warranty.

See Warranty information.

• Completion Time – 1 to 3 Hours. New installations

require more time than replacement installations.

IMPORTANT – The dishwasher MUST be installed to

allow for future removal from the enclosure if service is

required.

Care should be exercised when the appliance is installed

or removed,

to reduce the likelihood of damage to the

power supply cord.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories – See the Owner’s Manual for

available custom panel kits.

Your dishwasher is a water heating appliance.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

31-31587 01-18 GEA

• Remove all power leading to the appliance from the

circuit breaker or fuse box before beginning installation.

Failure to do so can result in a risk of electrical shock.

•

To reduce the risk of electric shock, fire, or injury to persons,

the installer must ensure that the dishwasher is completely

enclosed at the time of installation.

• The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative

if you are in doubt that the appliance is properly

grounded. If house wiring is not 2-wire with ground, a

ground must be by the installer. When house wiring

is aluminum, be sure to use UL-Listed anti-oxidant

compound and aluminum-to-copper connectors.

•

To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires are

not pinched or damaged, the house wiring is attached to the

junction box bracket through a strain relief, and all electrical

connections made at the time of install (wire nuts) are

contained inside of

the junction box cover.

WARNING

• Retire todos los conductores de corriente del

electrodoméstico de disyuntor o de la caja del fusible

antes de comenzar con la instalación. Si no cumple con

esto, se podrá producir el riesgo de descargas eléctricas.

• Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador debe asegurarse

de que el lavaplatos esté completamente cerrado en

el momento de la instalación.

• La conexión inadecuada del conductor de conexión a

tierra del equipamiento puede provocar un riesgo de

descarga eléctrica. Consulte a un electricista calificado

o representante de servicio técnico si tiene dudas

sobre la correcta conexión a tierra del aparato. Si el

cableado doméstico no cuenta con un cable de 2 hilos

con conexión a tierra, un instalador debe realizar una

conexión a tierra. Cuando el cableado doméstico es de

aluminio, asegúrese de usar un compuesto antioxidante

y conectores de aluminio a cobre aprobados por UL.

• Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador deberá realizar un

control para asegurar que los cables no estén pellizcados

ni dañados, que el cableado del hogar esté conectado a la

ficha de la caja de empalmes a través de un amortiguador

de refuerzo, y que todas las conexiones eléctricas

realizadas en el momento de la instalación (tuercas para

cables) estén dentro de la tapa de la caja de empalmes.

ADVERTENCIA

PARTS SUPPLIED IN

INSTALLATION PACKAGE:

• Two 8-18 x 5/8” Phillips-head wood screws

• #10 hex head screw and junction box cover

• Drain hose (78” long)

• Hose clamp

• Literature, product samples and/or coupons

TOOLS YOU WILL NEED:

• Phillips-head screwdriver

• 1/4” and 5/16” nutdriver

• 6” Adjustable wrench

• Level

• Carpenter’s square

• Measuring tape

• Safety glasses

• Flashlight

• Bucket to catch water when flushing the line

• 15/16” socket (optional for skid removal)

• Gloves

• Pliers

For New Installations Only:

• Tubing cutter

• Drill and appropriate bits

• Hole saw set

MATERIALS YOU WILL NEED:

• WX09X70910 or WX09X70911 power cord if

applicable to your installation, or electrical cable

• UL-Listed wire nuts (3)

• Thread seal tape

• 90° elbow (¾” hose internal thread on one end,

opposite end sized to fit water supply)

• GPF65 Side-mount bracket kit for use with granite

countertops

For New Installations Only:

• Electrical cable

• Water line–3/8” minimum copper tubing (including

ferrule and compression nut)

• Strain relief for electrical connection

• Hand shut-off valve (recommended)

• Air gap for drain hose, if required

• Waste tee for house plumbing, if applicable

• GPF10S drain hose (10’ long), if needed

• Screw-type hose clamps

• Cord protector (power cord models only

as needed)

• Conversion leads (power cord models only

as needed)

Installation Preparation

Hole Saw Set

Measuring Tape

Tubing Cutter

Drill and Bits

Phillips-Head

Screwdriver

15/16” Socket

1/4” and 5/16”

Nutdriver

Bucket

Flashlight

Gloves

Carpenter’s

Square

Safety Glasses

Level

Pliers

6” Adjustable

Wrench

78" Drain Hose

Phillips-Head

Wood Screws

5/8" long

Screw Kit

#10

Hex Head

Junction Box Screw

1/2" long

Cord Protector

- Optional -

(Power Cord

Models Only)

Conversion Leads

WD21X10107

- Optional -

(Power Cord

Models Only)

Thread

Seal Tape

3 Wire Nuts

Hot Water Line–3/8"

Minimum Copper Tubing

Electrical Cable

or WR09X70910 or

WX09X70911 Power Cord

Screw-Type

Hose Clamps

Strain Relief

Shut-Off

Valve

GPF65 Side-Mount

Bracket Kit

Optional 10'

Drain Hose

GPF10S

Waste Tee

Coupler for optional

drain hose

90° Elbow

Air

Gap

Hose Clamp

Literature

Junction

Box Cover

CLEARANCES:

• When installed into a

corner, allow 2” min.

clearance between

dishwasher and adjacent

cabinet, wall or other

appliances.

• Allow 27” min. clearance

from the front of the

dishwasher for door

opening.

Countertop

27"

Dishwasher

Clearance for Door

Opening 2” Minimum

Installation Preparation

To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher

is completely enclosed at the time of installation.

WARNING

Para reducir el riesgo de

descarga eléctrica, incendio

o lesiones a personas, el instalador debe asegurarse

de que el lavaplatos esté completamente cerrado en

el momento de la instalación.

ADVERTENCIA

PREPARE DISHWASHER ENCLOSURE

Built-In Models Only: Spacemaker

Models Only:

• The rough cabinet opening must be at least 24” deep,

24” wide and approximately 34-1/2” ± 1/4” high from

floor to underside of the countertop.

• The dishwasher must be installed so that drain hose is

no more than 10’ in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides

and back, and must not support any part of the enclosure.

• The back wall should be free of pipes or wires.

• Adjacent cabinets should be square and plumb to

ensure a good fit.

• Make sure the floor is level inside the opening and

even with the finished floor of the kitchen. This will

facilitate removal of the dishwasher at a later date for

service, if needed.

Min.

• The rough cabinet opening must be at least 24” deep,

24” wide and approximately 34-1/4” ± 1/4” height.

• This dishwasher fits under a special sink with a depth

of 6” or less in a 1-1/2” countertop.

• The dishwasher must be installed so that drain hose is

no more than 10’ in length for proper drainage.

• The dishwasher must be fully enclosed on the top, sides

and back, and must not support any part of the enclosure.

• The back wall should be free of pipes or wires.

• Water line to

sink faucet

and drain from

sink can be run

through Area

“A.”

• Hot water line

to dishwasher

is installed in

Area “B.”

• Garbage

disposer, water

lines to faucet,

waste trap, air

gap and water

shut-off valve

are installed in

a 12” wide cabinet, Area “C”.

• Sink opening for garbage disposer must be dimensioned

as shown (7-1/2”) in Area “C.” This will provide clearance

for disposer and plumbing in Area “C” when using either

single or double bowl sink.

• Adjacent cabinets should be square and plumb to

ensure a good fit.

NOTE: A gap between the dishwasher tub front flange and

the front of the base cabinet may result due to either the

cabinet being less than 24” deep or the sink bowl not being

installed to specifications. If the gap is more than 3/4”, the

sink bowl must be relocated to meet specified dimensions.

Cabinet Side

Adjacent to Dishwasher

Sink

Installation

Cutout

8" X 20"

Adjacent Cabinet

Rear Cutout

12"

3-1/4"

12-1/2"

24”

min

24” min

7-1/2"

Dishwasher

Side View

11-3/4" Max.

Plumbing

Max.

34-1/4"

1/4"

10-1/4" MA .

PLUMBING

DEPTH

1" Max. To

Sink Flange

20-1/2" Max.

Sink Bowl

11" Min.

Drain

6" Max.

3/4" Min.

1-1/4"

1-1/2"

Close Elbow

Min. I.R.

24" Min.

Cabinet

Wall

Installation Preparation

DRAIN REQUIREMENTS

• Follow local codes and ordinances.

• Do not exceed 10’ distance to drain.

• A high drain loop or air gap is required. See below.

DETERMINE DRAIN METHOD

The type of drain installation depends on the following

questions.

• Do local codes or ordinances require an air gap?

• Is waste tee less than 18” above floor?

If the answer to either question is YES, Method 1

MUST be used.

•

If the answers are NO, either method may be used.

CABINET PREPARATION

• Drill a 1-1/2” diameter hole in the cabinet wall within

the shaded areas shown in PREPARE DISHWASHER

ENCLOSURE section for the drain hose connection.

The hole should be smooth with no sharp edges.

IMPORTANT – When connecting

drain line to disposer, check to be sure

that drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

Method 1 – Air Gap with Waste Tee or Disposer

An air gap must be used when required by local codes

and ordinances. The air gap must be installed according

to manufacturer’s instructions.

Tip: Avoid unnecessary service call charges.

Always be sure disposer drain plug has been removed

before attaching dishwasher drain hose to the disposer.

Remove

Drain

Plug

Method 2 – “High Drain Loop” with Waste Tee or Disposer

Special consideration for a dishwasher installed

on a pedestal

lf the dishwasher is installed on an elevated platform,

a high drain loop of at least 32" above the platform

must be provided in addition to the air gap requirement

determined above. This is necessary for proper drain

performance.

Waste Tee Installation Disposer Installation

18"

Min.

32"

Min.

Drain Hose Hanger

Waste Tee Installation

18"

Min.

32"

Min.

Drain Hose Hanger

Disposer Installation

Installation Preparation

Cabinet Preparation & Wire Routing

•

The wiring may enter the opening from either side, rear

or the floor within the shaded area illustrated above

in figure and defined in PREPARE DISHWASHER

ENCLOSURE section.

• Cut a 1-1/2" maximum diameter hole to admit the

electrical cable. Edges of hole should be smooth and

rounded. Permanent wiring connections may pass

through the same hole as the drain hose and hot water

line, if convenient. If cabinet wall is metal, the hole

edge must be covered with a bushing.

NOTE: Power cords with plug must pass through a

separate hole in the cabinet.

Electrical Connection to Dishwasher

Electrical connection is on the right front of dishwasher.

• For permanent connections the cable must be routed

as shown in figure. Cable must extend a minimum of

24" from the rear wall.

• For power cord connections, install a 3-prong

grounding type receptacle in the sink cabinet rear wall,

6" min. or 18" maximum from the opening, 6" to 18"

above the floor.

• Use only WXO9X70910 (5’ 5” long) or WX09X70911

(7’ 11” long) Dishwasher Power Cord Kit. Do not use

an extension cord or adapter plug with this appliance.

PREPARE ELECTRICAL WIRING

Electrical Requirements

• This appliance must be supplied with 120V, 60 Hz.,

and connected to an individual properly grounded

branch circuit, protected by a 15- or 20-ampere circuit

breaker or time-delay fuse.

• Wiring must be 2 wire with ground and rated for 167°F (75°C).

• If the electrical supply does not meet the above

requirements, call a licensed electrician before proceeding.

Grounding Instructions–Permanent Connection

This appliance must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

be connected to the equipment-grounding terminal or

lead on the appliance.

Grounding Instructions–Power Cord Models

This appliance must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current.

This appliance is equipped with a cord having an equipment-

grounding conductor and a grounding plug. The plug must

be plugged into an appropriate outlet that is installed and

grounded in accordance with all local codes and ordinances.

White

18"

24"

from Wall

from

Cabinet

Alternate Receptacle

Location in Adjacent

Cabinet

Ground

Black

18"

Receptacle

Location

Area

1-1/2" Dia. Hole (Max.)

Retire todos los conductores de corriente del

electrodoméstico de disyuntor o de la caja del fusible

antes de comenzar con la instalación. Si no cumple con

esto, se podrá producir el riesgo de descargas eléctricas.

ADVERTENCIA

Remove all power leading to the appliance from the

circuit breaker or fuse box before beginning installation.

Failure to do so can result in a risk of electrical shock.

WARNING

La conexión inadecuada del conductor de conexión

a tierra del equipamiento puede provocar un riesgo de

descarga eléctrica. Consulte a un electricista calificado

o representante de servicio técnico si tiene dudas sobre

la correcta conexión a tierra del aparato. No modifique el

enchufe que se suministra con el aparato; si no calza en el

tomacorrientes, haga que un técnico calificado le instale un

tomacorrientes adecuado.

ADVERTENCIA

The improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check with

qualified electrician or service representative if you are in

doubt that the appliance is properly grounded. Do not modify

the plug provided with the appliance; if it will not fit the outlet,

have a proper outlet installed by a qualified technician.

WARNING

Metal Cabinet

Wall

Cord Protector

(Obtain locally

as needed)

Hole Diameter

1-1/2” Maximum

WATER LINE CONNECTION

• If using a flexible braided supply hose, label the

hose with the installation date to use as reference.

Flexible braided hoses, elbows and gaskets should

be replaced in 5 years.

• Turn off the water supply.

• Install a hand shut-off valve in an accessible location,

such as under the sink. (Optional, but strongly

recommended and may be required by local codes.)

• Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than

3/8” copper tubing or a flexible braided hose. Route

the line as shown in PREPARE HOT WATER LINE

section and extend forward at least 19” from rear

wall.

• Adjust water heater for 120°F to 140°F temperature.

• Flush water line to clean out debris.

• The hot water supply line pressure must be 20-120

PSI.

Installation Preparation

PREPARE HOT WATER LINE

NOTE: GE Appliances recommends copper tubing for

the water line, but if you choose to use flexible hose,

use GE Appliances WX28X326, flexible braided hose.

• The water supply line (3/8” copper tubing or flexible

braided hose) may enter from either side, rear or

floor within the shaded area shown in figure.

• The water supply line may pass through the same

hole as the electrical cable and drain hose. Or, cut

an additional 1-1/2" diameter hole to accommodate

the water line. If power cord with plug is used, water

line must not pass through power cord hole.

IMPORTANT: The hot water supply line pressure must

be at least 20 PSI. Lower pressures could cause the

water valve to leak and cause water damage.

Cabinet Face

Shut-off

Valve

2" From Floor

19" From Wall

From

Cabinet

Hot

1-1/2”

Dia.

Hole

SINK UTILITY CONNECTIONS

(Spacemaker

Models Only)

• Sink faucet hot and cold water lines and the sink

drain line must run above and adjacent to the

dishwasher, not behind it. Refer to Areas A and C

in Figure A on page 3 and Figure F1 below. This is

necessary to provide clearance for the dishwasher

when it is installed in the cabinet. Utility lines routed

directly behind the dishwasher will interfere with

placement of the dishwasher in the cabinet and

cause it to extend beyond the adjacent cabinets.

• Figure illustrates an installation using a double bowl

sink, a disposer and a high drain loop.

NOTE: All utility lines are above, below or adjacent to

the dishwasher. None are routed behind it.

6” Double-bowl

stainless steel sink

Countertop

25” deep

1-1/2” thick

1-1/2” Close

elbow

Dishwasher

water inlet

valve

Dishwasher

drain hose

Hot water supply

to dishwasher

Valve to shut off

water to dishwasher

Cold water

Hot water

Spacemaker

dishwasher

STEP 1

PREPARATION

Locate the items in the installation package:

• Screws

• Junction box cover

• Drain hose and clamp

• Owner’s Manual

• Product samples and/or coupons

Dishwasher Installation

STEP 3

REMOVE WOOD BASE,

INSTALL LEVELING LEGS

IMPORTANT – Do not kick off wood base!

Damage will occur.

• Move the dishwasher close to the installation location

and lay it on its

back. NOTE:

Do not place the

dishwasher on its

side.

• Remove the 4

leveling legs on

the underside of

the wood base

with a 15/16”

socket wrench.

• Remove and

discard base.

• Screw leveling legs back into the dishwasher frame,

approximately 3/4” from frame as shown.

CHECK DOOR BALANCE

• With dishwasher on the wood base, check the door

balance by opening and closing the door.

• The door is properly balanced if it gently drops from a

1/2 open position and does not rise from the full open

position.

• If necessary increase or decrease tension as shown.

Latch door and adjust both springs to the same

tension setting to correct balance.

Tip: Avoid service calls for door balance problems.

Make sure the spring end is fully engaged in a frame

hole and the spring link is fully seated in the hinge arm.

STEP 2

Do not remove wood base until you

are ready to install the dishwasher. The dishwasher will

tip over when the door is opened if base is removed.

CAUTION

No quite la base de madera

hasta que esté listo para instalar el lavaplatos. Si se

quita la base, el lavaplatos se volcará cuando se abra

la puerta.

PRECAUCIÓN

Insert Hook Through

Hole from Inside of Frame

Link fully seated

in hinge arm

REMOVE ACCESS PANEL

AND TOEKICK

The top mounting holes in the access panel are slotted.

• Remove the lower two 10-16 x 3/8” sheet metal

screws. Do not remove the two top 8-32 x 1/4”

machine thread screws.

• Slide the access panel to the left as far as it will go.

• Gently pull the access panel forward to remove it

from the top screws.

Set access panel, toekick and screws aside for use

in Step 20.

Tip: Prevent tub

damage.

Remove only the

3/8” sheet metal

screws in this

step. This will

help prevent a

mix- up with the

1/4” machine

thread screws in

Step 20.

STEP 4

STEP 7

INSTALL DRAIN HOSE TO

DISHWASHER DRAIN PORT

Skip this step if drain hose has been preinstalled.

In this step you will need the drain hose and

clamp set aside in Step 1.

IMPORTANT – Prevent drain hose damage and

possible leaks. Be careful not to nick or cut the

drain hose.

• Route the small end of the drain hose from the

left side of the dishwasher through the strain relief

attached to the dishwasher frame and toward the

center of the dishwasher as shown in the figures.

• Place the hose clamp over the small end of the drain

hose.

• Push the small end of the drain hose over the drain

port on the collection chamber, making sure it is fully

seated against the hose stop.

• Tighten the hose clamp to at least 15 inch-pounds of

torque.

NOTE: The drain hose supplied with the dishwasher

is approximately 78” long. If a longer hose is needed,

a 10-foot-long hose may be purchased from an

authorized GE Appliances dealer. The 10-foot-long

hose is part number GPF10S.

Tip: Avoid unnecessary service charges for drain

issues.

Make sure the drain hose connection is leak-free and

the hose is routed through the strain relief so it will not

kink when the dishwasher is installed into the cabinet.

Dishwasher Installation

STEP 5

INSTALL POWER CORD

Skip this step if the dishwasher will be permanently

connected to the house electrical system or has a

factory-installed power cord.

• In this step you will need the junction box cover and

the #10 x 1/2” hex-head screw from the screw kit set

aside in Step 1.

• The power cord and connections must comply with

the National Electrical Code, Section 422 and/or local

codes and ordinances. Maximum power cord length is

6 feet. Power Cord Kit WX09X70910 or WX09X70911,

available for purchase from an authorized

GE Appliances dealer, meets these requirements.

• Install strain relief in the junction box bracket.

• Insert the power cord through the strain relief and tighten.

• Make sure black, white and green dishwasher wires are

threaded through the small hole in the junction box bracket.

• Connect power cord white (or ribbed) to dishwasher

white, black (or smooth) to dishwasher black and

ground to dishwasher green wire. Use UL-listed wire

nuts of appropriate size.

• Install junction box cover using the #10 hex-head

screw. Be sure wires are not pinched under the cover.

STEP 6

INSTALL 90° ELBOW

• Ensure rubber gasket is located between valve and

elbow.

• Thead the 90° elbow

onto the water valve.

• Do not over tighten

the elbow; water valve

bracket could bend or

the valve fitting could

break.

• Position the end of the

elbow to face the rear

of the dishwasher.

Junction

Box

Bracket

Ground

(Green)

White Black

Cover

Dishwasher Harness Wires

Power Cord or Home Wiring with Strain Relief

Water

Valve

Bracket

90° Elbow

Fill

Hose

Gasket

Strain

Relief

Drain Hose

o not use

this port if

present

Collection Chamber

Drain Port

Hose Clamp

Hose Stop

INSTALL OPTIONAL

GPF65 SIDE MOUNT

BRACKETS

Skip this step if the underside of countertop is

wood or woodlike material.

• Purchase and install the GPF65 side-mount bracket kit

if the underside of counter is granite or a similar material

that will not accept wood screws. The GPF65 kit is

available from authorized GE Appliances dealers.

• Refer to figure and follow the instructions included in the

kit.

Dishwasher Installation

INSERT DRAIN HOSE AND

POWER CORD, IF USED,

THROUGH CABINET

• Upright the dishwasher and position it in front of the

cabinet opening.

• Insert the drain hose into the hole previously drilled in

the cabinet wall.

• If a power cord is used, guide the end of the cord

through a separate hole cut for the power cord.

The power cord should be routed directly to the rear

of the junction box, avoiding contact with the door

spring and other dishwasher components.

Tip: Avoid unnecessary service charges for no fill,

drain or noise concerns.

Position utility lines so they do not interfere with

anything under or behind the dishwasher.

STEP 9

STEP 10

STEP 8

POSITION WATER LINE

AND POWER SUPPLY

• Position water supply line and house wiring on the

floor of the opening to avoid interference with base

of dishwasher and components under dishwasher.

Water

Line

Power

Supply

Water

Po w e r

Drain

Bracket

Attachment

Screws

(2 Each

Side)

Side-Mounting

Brackets

Tub Frame

Optional

Side-Mount

Bracket Kit

Dishwasher Installation

SLIDE DISHWASHER INTO

CABINET

IMPORTANT – Do not push against front panel with

knees. Damage will occur.

• Grasp the sides of the front panel and slide the

dishwasher into the opening a few inches at a time.

Pull the drain hose and power cord, if equipped,

through the holes in the adjacent cabinet while sliding

the dishwasher into position.

• Check the tub insulation blanket, if equipped, to be

sure it is smoothly wrapped around the tub. It should

not be “bunched up” and it must not interfere with

the door springs. If the insulation is “bunched up” or

interfering with the springs, straighten and re-center

the blanket prior to sliding the dishwasher into its final

position.

• Make sure the drain hose is not kinked under or

behind the dishwasher.

• Make certain the house wiring, drain line and water

line do not interfere with components under the

dishwasher.

• The dishwasher tub flange should be approximately

3/4” behind the face of the adjacent cabinet. Refer to

figure.

Tip: Avoid unnecessary service charges for panel

damage.

Do not press on the center of panel with hands or

knees when sliding dishwasher into position.

STEP 11

LEVEL DISHWASHER

IMPORTANT – Dishwasher must be level for proper

dish rack operation, wash performance and door

operation. The dishwasher must be leveled left to right

and front to back. This ensures the dish racks will not

roll in or out on their own, circulation water will flow to

the pump inlet, and the door will close without hitting

the side of the tub.

•

Remove the lower dish rack and place a level on the

door and lower rack track as shown in figure.

•

Adjust the level of the dishwasher by individually

turning the 4 legs on the bottom of the dishwasher as

shown. Ensure all 4 legs are firmly in contact with the

floor.

• The dishwasher is properly leveled when the level

indicator is centered left to right and front to back.

Also, the dishwasher door should close without hitting

the side of the tub.

• Replace the lower rack.

Tip: Prevent unnecessary service charges. Verify

dishwasher is leveled.

Pull the dish racks half way out. They should stay put.

Open and close the door. The door should fit in the

tub opening without hitting the side of the tub. If the

racks roll on their own, or the door hits the side of tub,

re-level the dishwasher.

STEP 12

Turn Legs

to Adjust

Check Level

Front to Back

Check Level

Side to Side

3/4”

Dishwasher Installation

FASTEN DISHWASHER

TO UNDERSIDE OF

COUNTERTOP OR SIDES

OF CABINET

In this step you will need the two 5/8” Phillips-head

wood screws set aside in Step 1.

IMPORTANT – Dishwasher must be centered in cabinet

opening. Interference with cabinets or countertop will

cause leaks and damage to the door panel and/or

control panel.

•

If countertop is wood or woodlike material, fasten the

dishwasher to the countertop by driving the Phillips-

head screws through the countertop brackets and

into the countertop.

•

If the countertop is granite or similar material, drive

Phillips screws through side mount brackets and into

the adjacent cabinets.

•

Make sure screws are driven straight and flush to

prevent interference with door operation and damage

to the control panel. See figure.

Tip: Avoid unnecessary service charges for leaks

or control panel damage.

Make sure the dishwasher is centered in the cabinet

and the door opens and closes freely without hitting the

adjacent cabinets. Drive mounting screws straight and

flush.

STEP 13

Countertop

Bracket

Side-Mount

Brackets (optional)

3/4”

CONNECT WATER

SUPPLY

Connect water supply line to 90° elbow.

If using a flexible braided hose connection:

• Attach nut to 90° elbow using an adjustable wrench.

If using a copper tubing connection:

•

Slide compression nut, then ferrule over end of water

line.

• Insert water line into 90° elbow.

•

Slide ferrule against elbow and secure with

compression nut.

IMPORTANT – Check to be sure that door spring and/

or door spring cable do not rub or contact the fill hose

or water supply line. Test by opening and closing the

door. Re-route the water supply lines if a rubbing noise

or interference occurs.

Tip: Avoid unnecessary service charges for noise

or leaks.

Make sure the door spring does not rub against the fill

hose or water supply line.

STEP 14

90° Elbow

Hot Water

Supply Line

Fill Hose

Water Valve Bracket

Ferrule

Hot Water

Supply Line

Compression Nut

90°

Elbow

Dishwasher Installation

CONNECT DRAIN LINE

(CONT.)

• Connect drain line to air gap, waste tee or disposer

using the previously determined method. Secure

hose with a screw-type clamp.

Method 1 – Air gap with waste tee or disposer

Method 2 – “High drain loop” with waste tee or

disposer

Fasten drain hose to underside of countertop with a

hanger.

IMPORTANT – When connecting drain line to

disposer, check to be sure that

drain plug has been removed.

DISHWASHER WILL NOT DRAIN IF

PLUG IS LEFT IN PLACE.

Tip: Avoid unnecessary service call charges for a

no drain complaint.

Make sure excess drain hose has been pulled through

the cabinet opening. This will prevent excess hose

in the dishwasher cavity from becoming kinked or

crushed by the dishwasher.

CONNECT DRAIN LINE

The molded end of the drain hose will fit 5/8” through 1”

diameter inlet ports on the air gap, waste tee or disposer.

• Determine size of inlet port.

• Cut drain hose connector on the marked line, if required,

to fit the inlet port.

• If a longer drain hose is required, and you did not

purchase the GPF10S drain hose, add up to 42” length,

for a total of 120” (10 feet), to the factory- installed

hose. Use 5/8” or 7/8” inside diameter hose and a

coupler to connect the two hose ends. Secure the

connection with hose clamps.

IMPORTANT: TOTAL DRAIN HOSE LENGTH MUST

NOT EXCEED 10 FEET FOR PROPER DRAIN

OPERATION.

Cutting Line

5/8"

IMPORTANT: Do not cut corrugated

portion of hose

STEP 15 STEP 15

Hose

Clamp

Coupler Hose

Clamp

Waste Tee Installation Disposer Installation

18"

Min.

32"

Min.

Drain Hose Hanger

Waste Tee Installation

18"

Min.

32"

Min.

Drain Hose Hanger

Disposer Installation

Remove

Drain

Plug

Dishwasher Installation

CONNECT POWER SUPPLY

If a power cord with plug is already installed

proceed to Step 17.

• Secure house wiring to the back of the junction box

with a strain relief.

• Locate the 3 dishwasher wires, (white, black and green)

with the stripped ends coming out of the AC jumper. Use

UL-listed wire nuts of appropriate size to connect incoming

ground to green, white to white and black to black.

STEP 16

CONNECT POWER SUPPLY

(CONT.)

STEP 16

Si el cableado doméstico no cuenta con un cable

de 2 hilos con conexión a tierra, un instalador debe

realizar una conexión a tierra.

Cuando el cableado doméstico es de aluminio,

asegúrese de usar un compuesto antioxidante y

conectores de aluminio a cobre aprobados por UL.

ADVERTENCIA

If house wiring is not 2-wire with ground, a ground

must be provided by the installer.

When house wiring is aluminum, be sure to use

UL-Listed anti-oxidant compound and aluminum-to-

copper connectors.

WARNING

The Current Sensing Module (CSM) is a current-

sensing device located behind the toekick. It is

possible for the CSM to trip during shipping. If

that occurs, the installer can reset the CSM during

installation. If the CSM trips after the appliance

is installed and energized, DO NOT RESET THE

CSM. CALL SERVICE. Failure to have a qualified

service technician examine an installed dishwasher

after the CSM trips can result in personal injury or

damage to the appliance or property.

CAUTION

El Módulo de Detección Actualizada (Current

Sensing Module, CSM) es un dispositivo de

detección actualizada ubicado detrás del tope de

pie. Existe la posibilidad de que el CSM se caiga

durante el envío. Si esto ocurre, el instalador puede

reiniciar el CSM durante la instalación. Si el CSM se

cae luego de que el electrodoméstico fue instalado

y conectado, NO REINICIE EL CSM. LLAME AL

SERVICIO TÉCNICO. Si el lavavajillas ya instalado

no es examinado por un técnico calificado del

servicio técnico luego de una caída del CSM, se

podrán producir lesiones personales o daños sobre

el electrodoméstico o la propiedad.

PRECAUCIÓN

INSTALL JUNCTION BOX

COVER

If junction box cover is already installed, skip to

Step 18.

• In this step you will need the junction box cover and

the

#10 Hex head screw from the screws set aside in

Step 1.

• Install the junction box cover using #10 hex head screw.

Check to be sure that wires are not pinched under the

cover and that all wire nuts are inside the cover.

STEP 17

To reduce the risk of electric shock, fire, or injury to

persons, the installer should check to ensure that wires

are not pinched or damaged, the house wiring is attached

to the junction box bracket through a strain relief, and

all electrical connections made at the time of install (wire

nuts) are contained inside of the junction box cover.

WARNING

Para reducir el riesgo de descarga eléctrica, incendio

o lesiones a personas, el instalador deberá realizar un

control para asegurar que los cables no estén pellizcados

ni dañados, que el cableado del hogar esté conectado a la

ficha de la caja de empalmes a través de un amortiguador

de refuerzo, y que todas las conexiones eléctricas realizadas

en el momento de la instalación (tuercas para cables) estén

dentro de la tapa de la caja de empalmes.

ADVERTENCIA

Junction

Box

Bracket

Ground

(Green)

White

Black

Cover

Dishwasher Harness Wires

Home Wiring with Strain Relief

Dishwasher Installation

DISHWASHER WET TEST

CHECKLIST

• Turn on power supply or if power cord is used, plug

it into the wall outlet.

• Latch dishwasher door.

• For electronic dishwashers, select the NORMAL

WASH cycle and press the START pad one time.

• For dial models, press the NORMAL WASH only

pad, (or on some models, the NORMAL WASH

and HOT START pads if the model has them) and

then turn the control dial just enough to start the

dishwasher. Be careful not to turn the dial past the

first water fill. Dial should point to Hot Start Option

(or Hot Prewash Option) depending on model.

• Check to be sure that water enters the dishwasher.

This could take up to 4 minutes.

If water does not enter the dishwasher:

– Check to be sure that the water is turned on.

– Lightly tap the flood float cover to dislodge a stuck

flood float.

STEP 19

PRE-TEST CHECKLIST

Review this list after installing your dishwasher to

avoid charges for a service call that is not covered

by your Warranty.

• Verify that power is turned off at the source.

• Open the dishwasher door and remove all foam and

cardboard packaging.

• Read the Owner’s Manual to familiarize yourself with

the operation of the dishwasher.

• Check to be sure that the wiring is secure under the

dishwasher and not pinched or in contact with door

springs or other dishwasher components.

• Check that the door spring does not contact the

water line, fill hose, or adjacent cabinets. See Steps

13 and 14.

• Pull lower rack about halfway out. Check to be sure

it does not roll back into dishwasher or further out. If

it does, relevel the dishwasher. See Step 12.

• Check to be sure control panel does not touch

adjacent cabinets. If it does, reposition the

dishwasher. See Step 13.

• Turn on the hot water faucet at the sink to verify

that the water temperature is at least 120°F and not

more than 140°F. Adjust water heater if necessary.

• Add two quarts of water to the bottom of the

dishwasher to lubricate the pump seal.

• Turn on water supply.

• Check for water leaks. Tighten connections if

necessary. See Step 14.

• Remove the protective film, if present, from the

control panel, access panel and door panel.

STEP 18

Hi- T emp

W ash

Heavy

W ash

P ots

& P ans

Cycles

Normal

W ash

Hot

S ta r t

Hea t ed

D r y

Hot Start

Option

S ta r t Delay

(HRS)

Cycle

Off

Pla t e W armer

(Heated D r y On)

Rinse Only

(Heated D r y Of f )

S ta r t

Light W ash

R eset

Appearance varies by model. Not all models have push pads.

On some models

Appearance varies by model.

ots

&Pans

Cycles

Options

Hot Start

Option

Start

Off

Plate Warmer

(Heated Dry On)

Rinse Only

(Heated Dry Off )

Light Wash

Normal

Wash

Heated

Dry

Reset

Option

On some models

Flood Float

Cover

EAVY

ASH

OTS

PANS

Cycles

ORMAL

ASH

HINA

RYSTAL

INSE

NLY

TAR T

ESET

LEAN

HI T

EMP

INSE

HI T

EMP

ASH

EATED

ELAY

OURS

OCK

(2 T

IMES

)

248

Appearance varies by model.

On some models

Dishwasher Installation

DISHWASHER WET TEST

CHECKLIST (CONT.)

• Check the electrical connection to the water valve.

The red electrical connector should be plugged into

the dishwasher water valve. If it is not plugged in,

turn off electrical power to the dishwasher. Plug the

red connector into the dish washer water valve and

then restore power.

• Check for leaks under the dishwasher. If a leak

is found, turn off power, tighten connections and

restore power.

• Check for leaks around the door. A leak around

the door could be caused by the dishwasher door

rubbing or hitting adjacent cabinets. Reposition the

dishwasher if necessary. See Steps 11, 12 and 13.

• Most dishwasher models will drain about 3 minutes

after the first fill. Check the drain line for leaks when

dishwasher drains. If leaks are found, turn off power,

correct as necessary and then restore power.

• Open the dishwasher door and make sure most of

the water has drained. If the water does not drain,

check to be sure disposer plug has been removed

and/or air gap is free of debris.

• Let the dishwasher run through another fill and drain

cycle. Check again to be sure there are no leaks.

• At the end of the second drain, push the RESET

pad on electronic models. For dial models, unlatch

the door and rotate the dial to the Off position.

STEP 19

Red Connector

REPLACE ACCESS

PANEL AND TOEKICK

In this step you will need the panels and the two

screws set aside in Step 4.

There are two types of screws used. The 8-32 x 1/4”

screws are used at the top of the access panel and

should still be in place. The 10-16 x 3/8” screws are

used at the bottom of the access panel and secure

both the access panel and toekick.

IMPORTANT – Screws are not interchangeable.

To prevent damage to your dishwasher, use the

proper screw in the proper location. Do not mix

screw types or lengths.

• Place the toekick against the legs of the dishwasher.

• Remove the two 8-32 x 1/4” machine-thread screws.

• Align the access panel to the dishwasher.

• Select the two 8-32 x 1/4” machine-thread screws

just removed and insert them through the top holes

in the access panel and into the dishwasher frame.

• Tighten these screws.

• Align the toekick and make sure the bottom edge

is against the floor.

• Insert and tighten the two 10-16 x 3/8” sheet metal

thread screws, making sure the bottom edge of the

toekick stays in contact with the floor.

Tip: Prevent tub damage and reduce sound from

under the dishwasher.

Use the machine-thread screws in the top holes and

the sheet metal-thread screws in the bottom holes.

Make sure the toekick is against the floor.

STEP 20

LITERATURE

•

Be sure to leave complete literature package, these Installation

Instructions and product samples and/or coupons with the

consumer.

STEP 21

Appendix

NOTE: Product improvement is a continuing endeavor at GE Appliances.

Therefore, materials, appearance and specifications are subject to

change without notice.

CONVERTING DISHWASHER WITH

FACTORY- EQUIPPED POWER CORD

TO A PERMANENT CONNECTION

This procedure requires the conversion leads set aside in

Step 1.

• Make sure the power cord for the dishwasher is

unplugged from the wall outlet.

• Remove screw from junction box cover and remove cover

if present.

• Disconnect the three power cord conductors from the

dishwasher harness.

• Remove and discard the power cord.

• Connect the conversion harness (optional) to the

dishwasher harness by connecting like-colored wires.

• Return to Step 16 in these instructions to complete the

conversion.

Conversion Harness

Printed in the United States

Directives d’installation

Lave-vaisselle encastré et Spacemaker

Pour toute question, composez le 800.561.3344 ou visitez notre site web:

electromenagersge.ca

POUR VOTRE SÉCURITÉ

Veuillez lire et observer toutes les mises en garde

(AVERTISSEMENT et ATTENTION) données dans les

présentes directives.

Pour effectuer l’installation décrite dans les présentes

directives, il faut porter des gants et des lunettes de

sécurité.

IMPORTANT – Observez tous les codes et ordonnances

en vigueur.

• Note à l’installateur – Veuillez laisser les présentes

directives au consommateur pour l’inspecteur local.

• Note au consommateur – Veuillez conserver les

présentes directives avec votre Manuel d’utilisation

pour consultation ultérieure.

• Compétences requises – L’installation de ce

lave-vaisselle exige des compétences de base

en mécanique, en électricité et en plomberie.

L’installateur est responsable de la qualité

de l’installation. Toute défaillance du produit

attribuable à une installation inadéquate n’est

pas couverte par la garantie de GE Appliances.

Reportez-vous à la Garantie du produit.

• Durée de l’installation – Entre 1 et 3 heures.

L’installation d’un nouveau lave-vaisselle exige plus de

temps que le remplacement d’un ancien modèle.

IMPORTANT – Le lave-vaisselle DOIT être installé de

manière à ce qu’il puisse être sorti de son emplacement

si des réparations sont nécessaires.

Il importe d'user de prudence lorsque l'appareil est

installé ou déplacé afin de prévenir l'endommagement

du cordon d'alimentation.

Si le lave-vaisselle que vous avez reçu est endommagé,

communiquez immédiatement avec votre détaillant ou

l’entrepreneur en construction.

Accessoires facultatifs – Reportez-vous au Manuel

d’utilisation pour connaître les ensembles pour panneau

décoratif personnalisé offerts.

Votre lave-vaisselle est un appareil qui chauffe l’eau.

VEUILLEZ LIRE ATTENTIVEMENT

CONSERVER CES DIRECTIVES

VÉRIFIEZ LES POINTS SUIVANTS

Le lave-vaisselle est d'équerre et de niveau par rapport au

bas et au haut de l'ouverture de l'armoire, sans torsion ni

déformation de la cuve ou de la porte

Les quatre (4) pieds reposent fermement sur le plancher

Le boyau de vidange n'est pas coincé entre le lave-

vaisselle et les armoires ou les murs adjacents

31-31587 01-18 GEA

AVANT DE COMMENCER

Veuillez lire attentivement toutes les directives qui suivent.

• Avant de commencer l’installation, coupez toute

alimentation menant de l’appareil au disjoncteur ou

au fusible. Dans le cas contraire, vous pourriez être

victime d’une décharge électrique.

• Pour réduire les risques de choc électrique,

d’incendie ou de blessures, l’installateur doit

s’assurer que le lave-vaisselle est complètement

encastré au moment de l’installation.

• Un branchement inadéquat du conducteur de

mise à la terre peut présenter des risques de choc

électrique. Si vous n’êtes pas certain que l’appareil

est correctement mis à la terre, consultez un

réparateur ou un électricien qualifié. Si le câblage

électrique de la résidence n’est pas constitué de

deux fils plus un fil de mise à la terre, l’installateur

doit installer un fil de mise à la terre. Si le câblage

électrique de la résidence est en aluminium, utilisez

un agent antioxydant et des connecteurs pour

raccords «aluminium-cuivre» homologués UL.

•

Pour réduire les risques de choc électrique, d’incendie ou

de blessures, l’installateur doit vérifier pour s’assurer que

les fils ne sont pas pliés ou en dommagés, que le câblage

domestique est fixé au support de boîte de connexion par

l’entremise d’un serre-câble et que toutes les connexions

électriques faites au moment de l’installation (capuchons

de connexion) se trouvent à l’intérieur du couvercle de la

boîte de connexion

AVERTISSEMENT

Préparation pour l’installation

PIÈCES FOURNIES

DANS L’EMBALLAGE :

• Deux vis à bois Phillips n° 8-18 x 15,8 mm

(5/8 po)

• Vis à tête hexagonale n° 10 et couvercle de la

boîte de jonction

• Boyau de vidange (198 cm [78 po] de long)

• Collier

• Documentation, échantillons et(ou) bons

OUTILS NÉCESSAIRES :

• Tournevis cruciforme

• Tournevis à douille de 5/16 po et 1/4 po

• Clé à molette de 15 cm (6 po)

• Niveau

• Équerre de menuisier

• Ruban à mesurer

• Lunettes de sécurité

• Lampe de poche

• Seau pour attraper l’eau lors de la purge du tuyau

• Douille de 15/16 po (optionnelle pour la dépose de la palette)

• Gants

• Pince

Pour une nouvelle installation :

• Coupe-tube

• Perceuse et mèches appropriées

• Jeu de scie-cloche

MATÉRIAUX NÉCESSAIRES :

• Cordon d’alimentation WX09X70910 ou WX09X70911,

si nécessaire pour votre installation

• Connecteurs vissables homologués UL (3)

• Ruban pour joints filetés

• Coude de 90° (19,1 mm [3/4 po] filet pour tuyau

d’arrosage de jardin à une extrémité et l’autre

extrémité conçue pour le raccordement à la conduite

d’alimentation en eau)

• Ensemble de supports de montage latéraux GPF65 si

le comptoir est en granite

Pour une nouvelle installation :

• Câble électrique

• Conduite d’alimentation en eau–tuyau en cuivre d’au

moins 9,5 mm (3/8 po) (y compris bague et écrou à

compression)

• Bague anti-traction pour le raccordement électrique

• Robinet d’arrêt (recommandé)

• Coupure anti-refoulement pour le boyau

de vidange, si nécessaire

• Raccord en T pour la plomberie de la

résidence, s’il y a lieu

• Boyau de vidange GPF10S (3 m / 10 pi de

long), si nécessaire

• Colliers à vis sans fin

• Protège-cordon d’alimentation (modèles dotés

d’un cordon d’alimentation seulement, selon les

besoins)

• Fils pour la conversion (modèles dotés d’un

cordon d’alimentation seulement, selon les besoins)

Scie-cloche

Ruban à mesurer

Coupe-tube

Perceuse et

mèches

Tournevis

cruciforme

Douille de 15/16

Tournevis à douille

de 5/16 po et 1/4 po

Seau

Lampe de poche

Gants

Équerre de

menuisier

Lunettes de sécurité

Niveau

Pince

Clé à molette

de 15 cm (6 po)

Collier

Boyau de vidange

de 198 cm (78 po)

3 connecteurs

vissables

Câble électrique ou

cordon d'alimentation

WR09X70910 ou

WX09X70911

Couvercle

de la boîte

de jonction

Vis à bois Phillips

n° 8 de 15,8 mm

(5/8 po) de long

Ensemble de Vis

Vis à tête hexagonale n°

10 de 12,7 mm (1/2 po) de

long pour boîte de jonction

Documentation

Ruban

pour joints

filetés

Ensemble

de supports

de montage

latéraux GPF65

Coude

de 90°

Protège-cordon

d’alimentation

- Optionnel -

(modèles dotés

d’un cordon

d’alimentation

seulement)

Fils pour la

conversion

WD21X10107

- Optionnel -

(modèles dotés

d’un cordon

d’alimentation

seulement)

Conduite d’eau chaude–

tuyau en cuivre d’au

moins 9,5 mm (3/8 po)

Colliers à vis

sans fin

Bague

anti-traction

Robinet

d’arrêt

Boyau de vidange

facultatif GPF10S

de 3 m (10 pi)

Raccord

en T

Raccord pour boyau

de vidange facultatif

Coupure

anti-refoulement

Préparation pour l’installation

Clearance for Door

Opening 2" Minimum

Countertop

Dishwasher

25-1/2"

Comptoir

Lave-vaisselle

5,1 cm (2 po) minimum

pour l’ouverture de la porte

69 cm (27 po)

DÉGAGEMENTS :

• Dans le cas d’une

installation dans un

coin, veuillez prévoir

un dégagement d’au

moins 5,1 cm (2 po)

entre le lave-vaisselle

et les armoires, le mur

ou un électroménager

adjacent.

• Veuillez prévoir un

dégagement d’au

moins 69 cm (27 po)

à l’avant du lave-

vaisselle.

PRÉPARATION DE L’OUVERTURE DANS LES ARMOIRES

Modèles encastré uniquement :

Modèles Spacemaker

uniquement :

• L’ouverture dans les armoires doit mesurer au moins 61,0 cm

(24 po) de largeur et de profondeur, et environ 87,6 cm ±

64 cm (34-1/2 po ± 1/4 po) de hauteur à partir du plancher

jusqu’au-dessous du comptoir.

• Le lave-vaisselle doit être installé de façon à ce que le boyau

de vidange mesure au maximum 3.05 mètres (10 pieds) pour

assurer une vidange adéquate.

• Le dessus, les côtés et l’arrière du lave-vaisselle doivent

être complètement dissimulés à l’intérieur de l’ouverture. Le

lave-vaisselle ne doit soutenir aucune partie de la structure

des armoires.

• Le mur du fond doit être exempt de tuyaux ou de fils

• Les armoires adjacentes doivent être à l’équerre et d’aplomb

pour une installation appropriée.

• Assurez-vous que le plancher est de niveau à l’intérieur de

l’ouverture et au même niveau que le plancher fini de la

cuisine afin de faciliter le retrait du lave-vaisselle si jamais il

faut le réparer dans le futur.

• L’ouverture de l’armoire doit avoir une largeur et une

profondeur d’au moins 61 cm (24 po) et une hauteur de 87

cm + 0.6 cm (34 1/4 po + 1/4 po).

• Ce lave-vaisselle s’encastre sous un évier spécial d’une

profondeur de maximum 15 cm (6 po) dans un plan de

travail de 3,8 cm ( 1 1/2 po).

• Le lave-vaisselle doit être installé au maximum à 3 mètres

(10 pieds) de l’évier pour assurer une vidange adéquate.

• Le dessus, les côtés et l’arrière du lave-vaisselle doivent

être complètement dissimulés à l’intérieur de l’ouverture. Le lave-

vaisselle ne doit soutenir aucune partie de la structure des

armoires.

• Le mur du fond doit être exempt de tuyaux ou de fils.

• Installer les tuyaux d’alimentation d’eau et de vidange de

l’évier dans la section A.

• Installer le tuyau d’eau chaude vers le lave-vaisselle dans la

section B.

• Installer le broyeur de déchets, les tuyaux d’alimentation d’eau

du robinet, le siphon, l’intervalle d’air et le robinet d’arrêt de

l’eau dans

une armoire

large de 30

cm (12 po),

la section C.

• Le diamètre

de l’ouverture

du broyeur

de déchets

dans l’évier

doit être de

19 cm (7 1/2

po), comme

indiqué à la

section C.

Ceci permet

d’installer le

broyeur et

la plomberie dans la section C avec un évier soit simple, soit

double.

• Les armoires adjacentes doivent être à l’équerre et d’aplomb

pour une installation appropriée.

REMARQUE : Il peut y avoir un espace entre le rebord avant

du bac du lave-vaisselle et l’avant de l’armoire si la profondeur

de l’armoire est moins de 61 cm (24 po) ou si la cuve d’évier

n’a pas été installée selon les directives. Si l’espacement est

de plus de 2 cm (3/4 po), il faut déplacer la cuve d’évier pour

qu’elle s’accorde aux dimensions indiquées.

Pour réduire les risques de choc électrique, d’incendie

ou de blessures, l’installateur doit s’assurer que le

lave-vaisselle est complètement encastré au moment

de l’installation.

AVERTISSEMENT

Min.

Le mur du fond

doit être exempt

de tuyaux ou de fils

12,5 cm

(5 po)

12,5 cm

(5 po)

61,0 cm

(24 po)

min.

Armoires

à l'équerre

et d'aplomb

15,2 cm

(6 po)

10,1 cm (4 po)

Le plancher DOIT

être au même niveau

que le plancher

de la pièce

La partie ombrée est réservée

à la plomberie et à l'électricité

Côté d’armoire

adjacent au lave-vaisselle

Découpe

pour l’évier

20 cm x 51 cm

(8 x 20 po) découpe

arrière de l’armoire

adjacente

30 cm

(12 po)

8 cm

61 cm

(24 po)

61 cm (24 po)

32 cm

(12-1/2 po)

12,5 cm (5 po)

19 cm

7-1/2 po

12,5 cm (5 po)

(3 1/4 po)

Vue latérale

du lave-vaisselle

Dég. max.

29,8 cm (11 3/4 po)

plomberie

Max. 10 cm

(4 po)

87 cm

(34 1/4 po)

6 mm (1/4 po)

PROFONDEUR MAX

DE 26 cm (10 1/4 po)

POUR PLOMBERIE

Max. 2,5 cm (1 po)

du rebord de l’évier

Max. 52 cm

(20 1/2 po)

cuve de l’évier

Min. 28 cm

(11 po) vidange

Max. 15 cm

(6 po)

Min. 1,9 cm

(3/4 po)

R.B. min.

3 cm (1 1/4 po)

Dégag.

de 3,8 cm

(1 1/2 po)

du coude

Min. 61 cm

(24 po) armoire

Mur

87,6 cm ± 6,3 mm

(34 1/2 po ± 1/4 po)

du dessous

du comptoir

au plancher

10,1 cm

(4 po)

61,0 cm

(24 po) min.

Préparation pour l’installation

EXIGENCES RELATIVES AU

SYSTÈME DE VIDANGE

• Veuillez observer les ordonnances et les codes locaux en vigueur.

• Le boyau de vidange doit avoir une longueur maximale de 3.05

mètres (10 pieds).

• Il faut prévoir une boucle de vidange élevée ou l’installation d’une

coupure anti-refoulement. Voir ci-dessous.

CHOIX DE LA MÉTHODE DE VIDANGE

Le type d’installation de vidange dépend des conditions suivantes.

• Les ordonnances ou codes locaux en vigueur exigent-ils une

coupure anti-refoulement?

• Le raccord T se trouve-t-il à moins de 46cm (18po) du plancher?

Si vous répondez OUI à l’une ou l’autre de ces

questions, vous DEVEZ utiliser la méthode n° 1.

• Si vous répondez NON, vous pouvez employer l’une ou l’autre

des méthodes.

PRÉPARATION DES ARMOIRES

• Percez un trou de 3,8 cm (1-1/2 po) de diamètre dans la paroi de

l’armoire qui se trouve dans la partie ombrée de la PRÉPARATION

DE L’OUVERTURE DANS LES ARMOIRES pour le boyau de

vidange. Assurez-vous que l’orifice ne présente pas d’arêtes vives.

IMPORTANT – Lorsque vous branchez

le boyau de vidange à un broyeur à

déchets, assurez-vous d’enlever le bouchon

de vidange. LE LAVE-VAISSELLE NE

POURRA PAS SE VIDER SI VOUS

LAISSEZ LE BOUCHON EN PLACE.

Conseil: Pour éviter des frais de réparation inutiles.

Assurez-vous d’enlever le bouchon de vidange du broyeur

à déchets avant d’y brancher le boyau de vidange du lave-

vaisselle.

18"

Min.

32"

Min.

Crochet pour boyau

de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

Remove

Drain

Plug

Enlevez le

bouchon

de vidange

Considérations spéciales dans le cas d’un

lave-vaisselle installé sur une plateforme

Si le lave-vaisselle est installé sur une plateforme, il faut

aménager une boucle de vidange à une hauteur d’au moins

82 cm (32 po) au-dessus de la plateforme, en plus d’installer

la coupure anti-refoulement indiquée ci-dessus, afin d’assurer

une vidange adéquate.

Méthode n° 1 – Coupure anti-refoulement avec raccord en T

ou broyeur à déchets

Il faut installer une coupure anti-refoulement lorsqu’elle est

exigée par les ordonnances et les codes locaux en vigueur.

Cette coupure anti-refoulement doit être installée conformément

aux directives données par le fabricant.

Méthode n° 2 – Boucle de vidange élevée avec raccord en

T ou broyeur à déchets

Installation avec raccord en T Installation avec broyeur

à déchets

18"

Min.

32"

Min.

Crochet pour boyau de vidange

46 cm

(18 po) min.

82 cm

(32 po)

min.

Installation avec raccord en T Installation avec broyeur

à déchets

La page charge ...

Hotpoint HDA2100HBB Guide d'installation

Marque: Hotpoint

Modèle: HDA2100HBB

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Hotpoint HDA2100HBB Installation guide

Hotpoint HDA2100HBB Guide d'installation

Hotpoint HDA2100HBB Guide d'installation

dans d''autres langues

Documents connexes

Autres documents