ELICA EVL436S3 Guide d'installation

1

Use, Care, and

Installation Guide

Guide

d’utilisation,

d’entretien et

d’installation

Guía de

instalación, uso y

mantenimiento

READ AND SAVE THESE

INSTRUCTIONS

LISEZ CES

INSTRUCTIONS ET

CONSERVEZ-LES

LEA Y CONSERVE

ESTAS INSTRUCCIONES

LIB0178328

Printed in Mexico

11/21

Models: EVL430S3

EVL436S3

2

Contenido

ENGLISH ��2

Important Safety Notice �� 3

Electrical & Installation Requirements ��4

Product Dimensions ��4

List of Materials ��5

Parts no supplied��5

Ducting Options ��6

Ducting version ��6

Ductless (Recirculating) ��6

Installation ��6

Install Range Hood ��7

Electrical Connection ��8

Complete Installation ��9

Description of the Hood ��9

Control �� 9

CFM Reduction System ��10

Mainteinance �� 10

Warranty �� 11

ENGLISH

Contents

IAPPROVED FOR RESIDENTIAL APPLIANCES

FOR RESIDENTIAL USE ONLY

READ AND SAVE THESE INSTRUCTIONS

PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.

INSTALLATION MUST COMPLY WITH ALL LOCAL CODES.

IMPORTANT: Save these Instructions for the Local Electrical Inspector’s use�

INSTALLER: Please leave these Instructions with this unit for the owner�

OWNER: Please retain these instructions for future reference�

Safety Warning: Turn o power circuit at service panel and lock out panel, before wiring this appliance�

3

Important Safety Notice

I CAUTION

FOR GENERAL VENTILATING USE ONLY� DO NOT USE TO

EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS OR

VAPOURS�

IWARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

A� Use this unit only in the manner intended by the

manufacturer� If you have questions, contact the

manufacturer�

B� Before servicing or cleaning the unit, switch power o at

service panel and lock service panel disconnecting means

to prevent power from being switched on accidentally�

When the service cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service

panel�

C� Installation work and electrical wiring must be done by

qualiﬁed person(s) in accordance with all applicable codes

& standards, including ﬁre-rated construction�

D� Sucient air is needed for proper combustion and

exhausting of gases through the ﬂue (Chimney) of fuel

burning equipment to prevent back- drafting�

Follow the heating equipment manufacturers guideline and

safety standards such as those published by the national

ﬁre protection association (NFPA), the american society

for heating, refrigeration and air conditioning engineers

(ASHRAE), and the local code authorities�

E� When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities�

F� Ducted fans must always be vented to the outdoor�

I CAUTION

To reduce risk of fire and to properly exhaust air, be sure to

duct air outside - do not vent exhaust air into spaces within

walls, ceilings, attics, crawl spaces, or garages�

IWARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT

WORK�

Install this hood in accordance with all requirements specified�

IWARNING

To reduce the risk of fire or electric shock, do not use this

hood with any external solid state speed control device�

IWARNING

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE�

a) Never leave surface units unattended at high settings�

Boilovers cause smoking and greasy spillovers that may

ignite� Heat oils slowly on low or medium settings�

b) Always turn hood ON when cooking at high heat or when

ﬂambeing food (I�e� Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flambe’)�

c) Clean ventilating fans frequently� Grease should not be

allowed to accumulate on fan or ﬁlter�

d) Use proper pan size� Always use cookware appropriate for

the size of the surface element�

e) Suitable for use in household cooking area�

IWARNING

TO REDUCE THE RISK OF INJURY TO PERSONS, IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:a

a) SMOTHER FLAMES with a close-ﬁtting lid, cookie sheet, or

other metal tray, then turn o the gas burner or the electric

element� BE CAREFUL TO PREVENT BURNS� If the ﬂames

do not go out immediately, EVACUATE AND CALL THE

FIRE DEPARTMENT�

b) NEVER PICK UP A FLAMING PAN - you may be burned�

c) DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result�

d) Use an extinguisher ONLY if:

1) You know you have a class ABC extinguisher, and you

already know how to operate it�

2) The ﬁre is small and contained in the area where it

started�

3) The ﬁre department is being called�

4) You can ﬁght the ﬁre with your back to an exit�

aBased on “Kitchen Fire Safety Tips” published by NFPA�

OPERATION

Always leave safety grills and filters in place� Without these

components, operating blowers could catch onto hair, fingers

and loose clothing�

The manufacturer declines all responsibility in the event of

failure to observe the instructions given here for installation,

maintenance and suitable use of the product�

The manufacturer further declines all responsibility for injury

due to negligence and the warranty of the unit automatically

expires due to improper maintenance�

ICAUTION

Automatically Operated Device - To Reduce The Risk Of

Injury Disconnect From Power Supply Before Servicing�

4

Electrical & Installation Requirements

IMPORTANT

Observe all governing codes and ordinances�

It is the customer’s responsibility:

• To contact a qualiﬁed electrical installer�

• To assure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA

70 — latest edition*, or CSA Standards C22�1-94, Canadian

Electrical Code, Part 1 and C22�2 No�0-M91-latest edition**

and all local codes and ordinances�

• If codes permit and a separate ground wire is used, it is

recommended that a qualiﬁed electrician determine that

the ground path is adequate�

• Do not ground to a gas pipe�

• Check with a qualiﬁed electrician if you are not sure range

hood is properly grounded�

• Do not have a fuse in the neutral or ground circuit�

IMPORTANT

• Save Installation Instructions for electrical inspector’s use�

• The range hood must be connected with copper wire only�

• The range hood should be connected directly to the fused

disconnect (Or circuit breaker) box through metal electrical

conduit�

• Wire sizes must conform to the requirements of the

National Electrical Code ANSI/NFPA 70 — latest edition*,

or CSA Standards C22�1-94, Canadian Electrical Code Part

1 and C22�2 No� 0-M91 - latest edition** and all local codes

and ordinances�

• A U�L�- or C�S�A�-listed conduit connector must be provided

at each end of the power supply conduit (at the range

hood and at the junction box)�

Copies of the standards listed may be obtained from:

* National Fire Protection Association Batterymarch Park Quincy, Massachusetts

02269

** CSA International 8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

BEFORE INSTALLING THE HOOD

1 For the most ecient air ﬂow exhaust, use a straight run

or as few elbows as possible�

CAUTION: Vent unit to outside of building, only�

2 At least two people are necessary for installation�

3 Fittings material is provided to secure the hood to most

types of walls/ceilings, consult a Qualiﬁed Installer, check

if they perfectly ﬁt with your cabinet/wall�

4 Do not use ﬂex ducting�

5 COLD WEATHER installations should have an additional

backdraft damper installed to minimize backward cold

air ﬂow and a nonmetallic thermal break to minimize

conduction of outside temperatures as part of the

ductwork� The damper should be on the cold air side of

the thermal break�

The break should be as close as possible to where the

ducting enters the heated portion of the house�

Make up air: Local building codes may require the use of

Make-Up Air Systems when using Ducted Ventilation Systems

greater than speciﬁed CFM of air movement� The speciﬁed

CFM varies from locale to locale� Consult your HVAC profes-

sional for speciﬁc requirements in your area��

Product Dimensions

A

B

C

D

E

G

F

Models

EVL430S3 EVL436S3

A30” (76�2 cm) 36” (91�4 cm)

B1911⁄16” (50 cm)

C* Max: 421⁄8” (107 cm)

Min: 286⁄16” (72 cm)

D** Max: 383⁄16” (97 cm)

Min: 286⁄16” (72 cm)

E6” (15�24 cm)

F73⁄16” (18�3 cm)

G83⁄16” (20�8 cm)

* Ductless (Recirculating) version

** Ducted version

5

List of Materials

Removing the packaging�

I CAUTION

Remove carton carefully, Wear gloves to protect against sharp

edges�

I WARNING

Remove the protective ﬁlm covering the product before

putting into operation�

Supplied Part Pieces Supplied Part Pieces

Hood assembly and

LED lamps already installed

1

Duct covers

2

5x45 mm 6

6” round air transition

1

5.4x75 mm 4

8x40 mm

2

3.5x9.5 mm 2

10x60 mm

4

4x8 mm 2

Duct cover bracket

1

Torx 10 adapter 1

Mounting template

1

Parts no supplied

Tools/Materials required

• Level

• Drill

• 11⁄4” (3�2 cm), 1⁄8” (3�2 mm), and 1⁄16” (4�8 mm) drill bits

• Pencil

• Wire stripper or utility knife

• Tape measure or ruler

• Pliers

• Caulking gun and weatherproof caulking compound

• Jigsaw or keyhole saw

• Metal snips

• Screwdrivers:

- Flat-blade

- Phillips

Optional accessories and consumable parts

KIT # Part

Recirculating Kit KIT02766

Long Chimney

Extension KIT02762

Grease Filters Kit GRI0009219B

Make up Air Kit KIT0148906

6

Ducting Options

CFM reduction kit

If required o desired this hood is to be used only in

conjunction with CFM reduction kit model KIT0175561�

Consult your HVAC professional and local building codes for

speciﬁc requirements in your area�

Ducting version

Closely follow the instructions set out in this manual�

All responsability, for any eventual inconveniences, damages

or ﬁres caused by not complying with the instructions in this

manual, is declined�

Ductless (Recirculating)

The hood is equipped with a 6” (15�2 cm) round transition

for discharge of fumes to the outside�

Roof Venting Wall Venting

A

B

A

B

A. Roof cap

B. 6” (15.2 cm) round vent

A. Wall cap

B. 6” (15.2 cm) round vent

In cases where it should not

be possible to discharge

cooking fumes and vapour

to the outside�

Attach a charcoal filter and

the deflector on the duct

cover support bracket�

Fumes and vapours are

recycled through the top

grille by means of a duct

connected to the transition

and the transition mounted

on the deflector�

For this version only:

purchase the Ductless

Recirculating Kit�

Minimum Duct Size:

6” Round Pipe�

B

A

A. Deector

B. 6” (15.2 cm) round vent

Preparation

Do not cut a joist or stud unless absolutely necessary� If a

joist or stud must be cut, then a supporting frame must be

constructed�

Fittings material is provided to secure the hood to most types

of walls/ceilings�

However, a qualiﬁed technician must verify suitability of the

materials in accordance with the type of wall/ceiling�

Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent�

Recommended installation height:

Hood installation height above cooktop is the users preference�

The lower the hood is above the cooktop, the more ecient

the capturing of cooking odors, grease and smoke�

I CAUTION

Installation Heights

GAS cooktops 30″ (76�2 cm)

ELECTRIC cooktops 24″ (61 cm)

There is no maximum mounting height, however, we

recommend mounting the hood no greater than 36” (91�4

cm) above the cooking surface� For every inch (2�54 cm)

above 36” (91�4 cm), fume and moisture capture eciency

diminishes at an increasing rate and may not deliver an

acceptable level of ventilating performance�

This hood is intended for household use�

PLEASE READ THE INSTALLATION MANUAL FOR SPECIFIC

APPLICATION� Check your ceiling height and hood height

before selecting your hood�

Installation

Prepare location

• It is recommended that the vent system be installed before

hood is installed�

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for exhaust vent�

• Check your ceiling height and the hood height maximum

before you select your hood�

1 Disconnect power�

2 Determine which venting method to use: roof, wall, or

nonvented�

3 Select a ﬂat surface for assembling the range hood�

Place covering over that surface�

I WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING�

4 Using 2 or more people, lift range hood onto covered

surface�

Mounting the duct cover bracket

1 Determine and mark the centerline on the wall where the

canopy hood will be installed� Disconnect power�

2 Select a mounting height from the Installation Heights

chart� Mark a reference line on the wall�

3 Tape template in place, aligning the template centerline

and bottom of template with hood bottom line and with

the centerline marked on the wall�

7

A

C

B

A. Centerline

B. Fastener locations

C. Mounting height reference (hood bottom line)

4 Mark centers of the fastener locations through the

template to the wall�

IMPORTANT: All screws must be installed into wood�

If there is no wood to screw into, additional wall framing

supports may be required�

5 Remove the template�

6 Drill 3⁄16” (4�8 mm) pilot holes at all locations where screws

are being installed into wood�

7 Install the 2 - 5 x 45 mm mounting screws� Leave a 1⁄4”

(6�4 mm) gap between the wall and the back of the screw

head to slide range hood into place�

1⁄4”

(6�4 mm)

Vent cover bracket installation

1 Attach vent cover bracket to wall ﬂush to the ceiling using

2 - 5 x 45 mm screws�

AC

D

B

A. 8 x 40 mm anchors

B. Centerline on wall

C. Vent cover support bracket

D. 5 x 45 mm screws

Complete preparation

1 Determine and make all necessary cuts in the wall for the

vent system� Install the vent system before installing the

hood� See “Venting Requirements” section�

2 Determine the required height for the home power supply

cable and drill a 1¼” (3�2 cm) hole at this location�

3 Run the home power supply cable according to the

National Electrical Code or CSA Standards and local codes

and ordinances� There must be enough ½” conduit and

wires from the fused disconnect (or circuit breaker) box to

make the connection in the hood’s electrical terminal box�

NOTE: Do not reconnect power until installation is complete�

4 Use caulk to seal all openings�

Install Range Hood

Connect Vent System

1 Install transition on top of hood (if removed for shipping)

with 2 - 3�5 x 9�5 mm screws using the Torx 10 adapter�

A

B

A. Vent transition

B. 3.5 x 9.5 mm screw

2 Remove protective ﬁlm from hood and duct covers�

Install Range Hood

1 Using 2 or more people, hang range hood on 2 mounting

screws through the mounting slots on back of hood�

A

B

C

A. Mounting screws

B. Mounting slots

C. Lower mounting

screws

2 Mark with a pencil the lower mounting holes location�

3 Uninstall the hood assembly, and drill 3⁄16” (4�8 mm) pilot

holes at marked locations�

4 Hang the range hood again on 2 upper mounting screws�

5 Level the range hood and tighten upper mounting screws�

6 Install 2 - 5 x 45 mm lower mounting screws and tighten�

Use the optional wall anchors if needed�

7 Remove styrofoam protection from inside the hood�

For vented installations only:

1 Fit vent system over the exhaust outlet�

2 Measure from the bottom of the air deﬂector to the

bottom of the hood outlet� Cut the ductwork at the

measured dimension�

Dimension

to measure

Roof outlet

Wall

outlet

3 Seal connection with clamps�

4 Check that back draft dampers work properly�

8

Electrical Connection

I WARNING

ELECTRICAL SHOCK HAZARD�

I WARNING

DISCONNECT POWER BEFORE SERVICING�

REPLACE ALL PARTS AND PANELS BEFORE OPERATING�

FAILURE TO DO SO CAN RESULT IN DEATH OR

ELECTRICAL SHOCK�

1 Disconnect power�

2 Remove terminal box cover�

3 Remove the knockout in the terminal box cover and install

a UL listed or CSA approved 1⁄2” strain relief�

4 Run home power supply cable through strain relief, into

terminal box�

A

B

C

D

E

A. Home power supply cable

B. UL listed or CSA approved strain

relief

C. Black wires

D. UL listed wire connectors

E. White wires

F. Green (or bare) and yellow-green ground

wires

5 Use UL listed wire connectors and connect black wires (C)

together�

6 Use UL listed wire connectors and connect white wires (E)

together�

I WARNING

ELECTRICAL SHOCK HAZARD�

I WARNING

ELECTRICALLY GROUND BLOWER�

CONNECT GROUND WIRE TO GREEN AND YELLOW

GROUND WIRE IN TERMINAL BOX� FAILURE TO DO SO CAN

RESULT IN DEATH OR ELECTRICAL SHOCK�

7 Connect green (or bare) ground wire from home power

supply to yellow-green ground wire (F) in terminal box

using UL listed wire connectors�

8 Tighten strain relief screw�

9 Install terminal box cover�

10 Check that all light bulbs are secure in their sockets�

11 Reconnect power�

Install duct covers

• When using both upper and lower vent covers, push lower

cover down onto hood and lift upper cover to ceiling and

install with two mounting screws�

NOTE: For vented installations, the upper vent cover may

be reversed to hide slots�

C

A

B

C

D

A. Upper vent cover

B. Lower vent cover

C. 4 x 8 mm screws

D. Bracket

NOTE: To prevent scratches, lay paper or a kitchen towel over

the edges of the lower ﬂue duct to protect the surface�

9

Complete Installation

• For non-vented (recirculating) installations only, install

charcoal ﬁlters over metal grease ﬁlter�

See the “Mainteinance” section�

• Install metal ﬁlters� See the “Mainteinance” section�

If range hood does not operate:

• Check that the circuit breaker is not tripped or the house

fuse blown�

• Disconnect power supply� Check that wiring is correct�

To get the most ecient use from your new range hood,

read the “Mainteinance” section.

Keep your Installation Instructions and Use and Care Guide

close to range hood for easy reference.

Description of the Hood

5

4

1

3

2

1. Blower and light controls

2. LED lamps

3. Grease lter handle

4. Grease lters

5. Duct covers

Control

A B

A. Light button

B. Blower button

Operating the light

The Light On/O button (A) controls both lights�

Press once for turning On soft light and the button sun

icon lightens with the bottom half of the edge slightly�

Press again for regular light and the button will be

completely illuminated�

Press a third time to turn O the light, the whole

button light turns o�

Operating the blower

Press the button (B) to turn On the hood on low

speed, the icon and right low corner of the edge on

button will be illuminated�

Press a second time for medium speed, the icon and

the lower half of the edge on the button enlightens�

Press again to high speed and ¾ of the edge on the

button will illuminate�

Press the button a fourth time to activate Boost speed

for five minutes (the full icon and edge will be illumi-

nated) and then, automatically switch to high speed�

Press the button a fifth time to turn Off the blower and

button lights�

Change light color

With lights and motor turned O, press and hold light button

for 3 sec, both buttons will fully illuminate on the current light

color� The buttons can be used to select desired color (Light

<< button backwards, Blower button forward >>)

Available light colors are white (default color), blue, green or

red� To set color, choose one and press both buttons at the

same time�

Sound

To enter sound mode, with lights and motor turned O

press both buttons at the same time and the upper left

corner of the light button will illuminate with white light� The

buttons can be used to select desired sound (Light <<button

backwards, Blower button forward>>)�

Available feedback sounds are regular beep, soft beep and

mute� As the regular and soft beep are selected, the hood

will reproduce each sound� When mute is selected, upper left

corner of the light button will illuminate with red light� To set

sound, choose one and press both buttons at the same time�

10

CFM Reduction System

Before operating your hood:

Some States and Provinces of the US & Canada restrict the

maximum exhausting airflow of range hoods�

Airflow is measured as cubic feet per minute (CFM)�

These maximum levels allowed are detailed in the local code

of your area� Please check local codes to find out if you need

to restrict the maximum airflow of your hood� If your local

code mandates a maximum airflow level below the maximum

airflow of this hood (i�e� 400 CFM), please execute the proce-

dure below to reduce the maximum airflow�

With blower and light turned O

• Press and hold both buttons at the same time for 3 sec you

will hear a beep and the icon lights (no edge) will illuminate

for 3 seconds�

• This action will disable speed 4 and eectively lower the

maximum airﬂow to > 300 CFM�

• Locate the CFM certiﬁcation sticker in the hardware pack�

• Peel and Ax this sticker to a visible area in the blower�This

sticker provides ocial certiﬁcation to your local inspector

that this hoods maximum airﬂow has been reduced to >

300 CFM�

Indicators of filter saturation:

At regular time intervals, the hood indicates the need of

performing filter maintenance�

Blower button icon blink (no edge):

Perform grease filter maintenance�

Light button blink (no edge):

Perform activated charcoal filter maintenance�

Reset of filter saturation indicators:

With blower Off press and hold the blower button for 3 sec�

Activation of saturation indicator activated charcoal ﬁlter:

NOTE: This operation must be performed with the hood off�

This indicator is normally deactivated; press and hold the

blower button for 3 sec� to activate the function: the button

blinks for 1 sec�

To deactivate the function, press and hold the blower button

for 3 sec�, the button blinks for half a sec�

Mainteinance

Cleaning

Do not spray cleaners directly to the control while cleaning the

Hood� The cooker hood should be cleaned regularly (at least

with the same frequency with which you carry out maintenance

of the fat ﬁlters) internally and externally� Clean using the

cloth dampened with neutral liquid detergent� Do not use

abrasive products� Do not use chlorine base cleaners�

DO NOT USE ALCOHOL!

I WARNING:

Failure to carry out the basic cleaning recommendations of the

cooker hood and replacement of the filters may cause fire risks�

Therefore, we recommend oserving these instructions�

The manufacturer declines all responsibility for any damage to

the motor or any fire damage linked to inappropriate maintenance

or failure to observe the above safety recommendations�

Grease Filter

Traps cooking grease particles�

This must be cleaned once a month using non aggressive

detergents, either by hand or in the dishwasher, which must be

set to a low temperature and a short cycle� When washed in

a dishwasher, the grease filter may discolour slightly, but this

does not affect its filtering capacity�

To remove the grease filter, pull the spring release handle�

A

A. Spring release handle

Replacing a LED Lamp

The LED lights are replaceable by a service technician only�

See “Who to contact” section in the warranty for service

contact information�

Charcoal ﬁlter

NOTE

When used in recirculation mode, To Reduce the Risk of Fire

and Shock use only conversion kit model KIT02766�

If the model is not vented to the outside, the air will be

recirculated through disposable charcoal filters that help

remove smoke and odors�

1 Cover the grill that protects the suction motor with the

carbon ﬁlter so that the slots on the ﬁlter correspond to

the pins on the sides of the motor protection grill�

2 Turn the carbon ﬁlter clockwise to block them (bayonet

ﬁxing)�

NOTE: The charcoal filters cannot be cleaned� It should be

replaced every 4-6 months (depending on hood usage)�

ELICA North America

TWO-YEAR LIMITED WARRANTY

TO OBTAIN SERVICE UNDER WARRANTY

Owner must present proof of original purchase date. Please keep a copy of your dated proof of purchase (sales slip) in

order to obtain service under warranty.

PARTS AND SERVICE WARRANTY

For the period of two (2) years from the date of the original purchase, Elica will provide free of charge, non consumable

parts or components that failed due to manufacturing defects. During these two (2) years limited warranty, Elica will also

provide free of charge, all labor and in-home service to replace any defective parts.

WHAT IS NOT COVERED

• Damage or failure to the product caused by accident or act of God, such as, ﬂood, ﬁre or earthquake.

• Damage or failure caused by modiﬁcation of the product or use of non-genuine parts.

• Damage or failure to the product caused during delivery, handling or installation.

• Damage or failure to the product caused by operator abuse.

• Damage or failure to the product caused by dwelling fuse replacement or resetting of circuit breakers.

• Damage or failure caused by use of product in a commercial application.

• Service trips to dwelling to provide use or installation guidance.

• Light bulbs, metal or carbon ﬁlters and any other consumable part.

• Normal wear of ﬁnish.

• Wear to ﬁnish due to operator abuse, improper maintenance, use of corrosive or abrasive cleaning products/pads and

• When the product has not been operated in accordance with the accompanying instructions for use.

oven cleaner products.

WHO IS COVERED

This warranty is extended to the original purchaser for products purchased for ordinary residential use in North America

(Including the United States, Guam, Puerto Rico, US Virgin Islands & Canada).

This warranty is non-transferable and applies only to the original purchaser and does not extend to subsequent owners of

the product. This warranty is made expressly in lieu of all other warranties, expressed or implied, including, but not limited

to any implied warranty of merchantability or ﬁtness for a particular purpose and all other obligations on the part of Elica

North America, provided, however, that if the disclaimer of implied warranties is ineective under applicable law, the dura-

tion of any implied warranty arising by operation of law shall be limited to two (2) years from the date of original purchase

at retail or such longer period as may be required by applicable law.

This warranty does not cover any special, incidental and/or consequential damages, nor loss of proﬁts, suered by the

original purchaser, its customers and/or the users of the Products.

WHO TO CONTACT

To obtain service under warranty or for any service related question:

USA & CANADA - Western Provinces

SERVICE POWER

888 732 8018

[email protected]

CANADA - Ontario Province

AGI Services

888 651 2534

[email protected]

CANADA - Quebec & Atlantic Provinces

Ateliers G. Paquette

800 463 0119

[email protected]

•

To ensure prompt after-sales service, when you call we will kindly ask you to provide the following information indicated

on the nameplate inside the hood: hood model, 12 NC and date of purchase on original invoice.To access the nameplate,

all you have to do is remove the grease ﬁlters.

•

Register your product in

elica.com

and earn a 3rd year of factory

warranty, covering all parts

plus in-home labor.

12NC:

Hood model:

Serial No:

Date of purchase on original invoice:

11

Warranty