Minelab ML80 Manuel utilisateur

ML80
Minelab
Marque
Minelab
Modèle
ML80
Catégorie
Écouteurs
Taper
Manuel utilisateur
Instruction Manual
123 4
58
Bluetooth Headset
Model No.: ML80
The Bluetooth headphones with its stylish design and ergonomic
construction, powered with noise cancelling stereo sound drivers,
latest CSR8670 chipset is compatible with the latest devices
supporting Bluetooth.
Package Contents
● Headphones
● 3.5mm Detachable Auxiliary cable
● USB Charging Cable
● Hard Shell Case
● Detachable Mesh Bag
● Instruction Manual
Product Specification
● Bluetooth Version: V4.1
● Bluetooth Modes Supported: headphones, hands free, A2DP,
AVRCP, aptX, aptX Low Latency
● Bluetooth Chipset: CSR8670 with aptX, aptX Low Latency
● Bluetooth Operating Range: up to 10m
● Charging Time: 3 hours
● Operating Time: 15-20 hours
● Standby Time: up to 180 hours
● Dimensions: 21.0 (L) x 16.0 (W) x 8 (H) cm (unfolded)
21.0 (L) x 16.0 (W) x 5 (H) cm (folded)
● Weight: 221g
Buttons and Indications
1. LED
2. Volume + / Previous track
3. Multi-Function Button (MFB) (Power ON/OFF, Make/An-
swer/End/Reject/Transfer calls, Play/Pause music, Voice Dialling,
Pairing and Factory Reset)
4. Volume - / Next track
5. 3.5mm audio jack
6. Microphone
7. USB charging port
Getting Started
To use your ML80 stereo Bluetooth headphones, follow the steps
below:
1. Ensure the Bluetooth headphones are fully charged.
2. Pair the charged Bluetooth headphones with a Bluetooth
enabled device
Charging the Headphones
Connect the USB charging cable to charging USB socket (7) of the
headphones. The LED (1) is red whilst charging and will turn off
once fully charged.
Turning on the Headphones
Press and hold the MFB (3) until the LED (1) flashes solid blue for 1
second and then flashes red and blue with an ascending "beep"
sound. The headphones enter pairing mode automatically when no
device is paired.
Turning off the Headphones
Press and hold the MFB (3) for 4 seconds until the LED (1) flashes
solid red then turns off with a descending "beep" sound.
Pairing the Headphones
1. Place the headphones and the detector no more than one metre
apart.
2. Ensure the headphones are turned off.
3. Press and hold the MFB (3) until a double ascending tone is
heard and the LED (1) flashes red and blue.
4. Press and hold the wireless button on the detector for 2 seconds.
All of the wireless symbols will flash.
5. When the pairing is complete, the headphones will beep and the
LED (1) will flash blue once every 3 seconds and will be connected
to the detector.
Note: If the pairing cannot be completed within 5 minutes after
the pairing mode has been activated, the headphones will go into
standby mode.
Note: ML80 headphones can be paired with 2 devices at once so
you can also pair them with your smart phone, however when a call
is received it will interrupt the detecting audio.
Cancel the Pairing Status
In standby mode, turn off the Bluetooth function of your device.
The headphones will need to be re-paired with your device after
power on again.
Connect with the Last Paired Device
The headphones will connect with the last paired device. If the
pairing is successful the LED (1) will flash blue every 3 seconds and
be in standby mode. If the pairing cannot be completed within 5
minutes after the pairing mode has been activated, the headphones
will go into standby mode.
Smart Phone Call Related Functions:
● Answer a Call
When a call is incoming, the ring tone will be heard via the
headphones. Press the MFB (3) once to accept the call or answer
the call via your smart phone.
● Reject / Ignore a Call
To reject / ignore an incoming call, press and hold the MFB (3) for
approximately 2 seconds until a “beep” is heard, then release.
● End a Call
Press the MFB (3) once to end a call or end a call via your smart
phone.
● Transfer a Call
Press the MFB (3) for 1 second until a “beep” is heard to transfer
a call from the headphones to a smart phone. Repeat this
procedure to transfer a call from a smart phone to the headphones.
● Last Number Re-dialing from the Headphones
In standby mode, double press the MFB (3) on the headphones.
Note: This function is only applicable to smart phones with
Bluetooth hands free. Functionality varies depending on the smart
phone model. Refer to your smart phone user guide for additional
information.
Music Functions:
● Play / Pause Music
Press the MFB (3) to play music when the device is paused and
press the MFB (3) to pause music when the device is playing.
When music is playing, the LED (1) is solid blue.
● Next / Previous Track
Long press the Volume – button (4) for 2 seconds to play the next
track.
Long press the Volume + button (2) for 2 seconds to play the
previous track.
● Changing the volume
Press the Volume + button (2) once to increase or the volume.
Press the Volume – button (4) once to decrease the volume.
When maximum or minimum volume has been reached the
headphones will give a high or low tone (beep).
Reset to factory defaults (including unpairing)
Make sure the headphones are turned off. Press the MFB (3) for
approximately 10 seconds until the headphones “beep” twice
while the LED (1) flashes red and blue twice then release the button.
The headphones will now be in pairing mode with the LED indicator
(1) flashing red and blue.
7
Using supplied 3.5mm headphone cable
A 3.5mm audio cable is included for use if the headphones battery
is flat. You may also use the audio cable with devices that do not
have Bluetooth capability.
Troubleshooting
If you are unable to connect your headphones to your device, try
the following:
● Ensure your headphones are turned off and properly charged.
● Ensure the headphones are paired with your device.
● Ensure your devices Bluetooth feature is activated. Refer to your
devices user guide for specific instructions.
● Ensure the headphones are within a 10 metre range of your
device and there are no obstructions, such as walls or other
electronic devices in between.
● If the above steps do not solve your problem, recharge the
headphones and turn the device off and on again.
Safety Information
● Check local laws regarding the use of smart phones and
headphones whilst driving. If you use the headphones whilst
driving, ensure your attention and focus remains on the road and
you drive in a responsible and safe manner.
● Never allow children to play with the headphones, small parts
are a choking hazard.
● Observe all signs that require an electrical device or RF radio
product to be switched off in designated areas. These could
include hospitals, blasting areas, and potentially explosive
environments.
● Turn off your headphones prior to boarding an aircraft.
● Never mount or store your headphones over any air bag
deployment area as serious injury may result if the air bag deploys.
● Do not open or mutilate the built-in battery.
● Dispose of batteries according to local regulations. Do not
dispose as household waste.
● Only charge the headphones built-in battery in accordance with
the instructions contained in the user guide.
● Avoid charging the headphones in extreme temperature
conditions.
Care and Maintenance Headphone
● Turn the headphones off before placing in a pocket or bag. If the
MFB (3) is accidentally activated, your smart phone may place an
unintended call if paired.
● Do not expose the headphones to liquid, moisture or humidity, as
the headphones are not waterproof.
● Do not use abrasive cleaning solvents to clean the headphones.
● Do not expose the headphones to extreme temperature
conditions. The storage temperature range is from -0 to +60oC.
● Do not dispose the headphones in a fire as this may result in an
explosion.
● Do not bring the headphones into contact with sharp objects as
this will cause scratches and damage.
● Do not attempt to disassemble the headphones, as they do not
contain serviceable components.
● If the headphones are not used for long periods, store in a dry
place free from extreme temperature conditions and dust.
Size: 70*93mm
● Bluetooth operating frequency: 2.402-2.480GHz
● Audio output power：15mW x2
● Power of supply: 0.1W
Simplified EU Declaration of Conformity
Minelab Electronics Pty Ltd hereby declares that this device complies
with Directive 2014/53/EU and The Radio Equipment Regulations
2017 (S.I. 2017/1206). Full text of the EU & UKCA Declaration of
conformity is available here: www.minelab.com/compliance.
69
LED indications
Certificate
Condition
Pairing state
Charging
Fully charged
Connected
Not connected
LED state
Alternating red blue
Solid red
off
Blue flash every 3 seconds
Blue flash every 2 seconds
018-180190
R-CRM-Tej-ML80
FCC ID:2APN8-RBT80
IC:24927-ML80
Note:
Qualcomm aptX is a product of Qualcomm Technologies, Inc.
and/or its subsidiaries.Qualcomm is a trademark of Qualcomm
Incorporated, registered in the United States and other countries.
aptX is a trademark of Qualcomm Technologies International, Ltd.,
registered in the United States and other countries.
Minelab Electronics, PO Box 35 Salisbury South, South
Australia 5106
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communica-
tions. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
L’émetteur/récepteur exempt de licence contenu dans le présent
appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes :
(1) L' appareil ne doit pas produire de brouillage;
(2) L' appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d' en compromettre le
fonctionnement.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference
that may cause undesired operation.
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development
Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC and Industry Canada statements
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
Modification
Any changes or modifications not expressly approved
by the grantee of this device could void the user’s authority
to operate the device.
  • Page 1 1

Minelab ML80 Manuel utilisateur

ML80
Minelab
Marque
Minelab
Modèle
ML80
Catégorie
Écouteurs
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents