Omega MOD16370915 Sub-1G Module Mode d'emploi
- Taper
- Mode d'emploi
MOD-16370-915
Sub-1G Module User Guide
OMEGA Engineering, Inc.
V1.0
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 23cm between the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03
OEM Manual v01 guidance, the following conditions must be strictly followed
when using this certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
2.2 List of applicable FCC rules
This module has been tested for compliance to FCC Part 15
2.3 Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any
other usage conditions such as co-location with other transmitter(s) or being
used in a portable condition will need a separate reassessment through a class
II permissive change application or new certification.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable.
2.6 RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 23cm between the radiator & your body. If the
module is installed in a portable host, a separate SAR evaluation is required to
confirm compliance with relevant FCC portable RF exposure rules.
2.7 Antennas
The following antennas have been certified for use with this module; antennas
of the same type with equal or lower gain may also be used with this module.
The antenna must be installed such that 23 cm can be maintained between the
antenna and users.
2.8 Label and compliance information
The final end product must be labeled in a visible area with the following:
“Contains FCC ID: WR3MOD16370915”. The grantee's FCC ID can be used only
when all FCC compliance requirements are met.
2.9 Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and any
co-located or simultaneous transmission with other transmitter(s) or portable
use will require a separate class II permissive change re-evaluation or new
certification.
2.10 Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does not
cover the FCC Part 15 Subpart B (unintentional radiator) rule requirement
applicable to the final host. The final host will still need to be reassessed for
compliance to this portion of rule requirements if applicable.
As long as all conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their end-
product for any additional compliance requirements required with this module
installed.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or co-location with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can not
be used on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
end product which integrates this module.
The end user manual shall include all required regulatory information/warning
as show in this manual.
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the essential
requirements of the FCC rule such as FCC Part 15 Subpart B before it can be
placed on the US market. This includes reassessing the transmitter module for
compliance with the Radio and EMF essential requirements of the FCC rules.
This module must not be incorporated into any other device or system without
retesting for compliance as multi-radio and combined equipment.
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le
dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit
accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un
fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
greater than 34 m between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus
de 34 cm entre le radiateur et votre corps.
This device is intended only for OEM integrators under the following conditions: (For
module device use)
1) The antenna must be installed and operated with greater than 34cm between the
antenna and users
2) The transmitter module may not be co-located with any other transmitter or antenna.
3) Module approval valid only when the module is installed in the tested host or compatible
series of host which have similar RF exposure characteristic with equal or larger antenna
separation distance.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) L'antenne doit être installé et exploité avec plus de 34 cm entre l'antenne et les
utilisateurs
2) 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
3) Approbation du Module valable que lorsque le module est installé dans l'hôte testé ou
de la série de l'hôte compatible qui ont même caractéristique de l'exposition aux RF avec
la distance égale ou supérieure séparation antenne.
Tant que les 3 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization
is no longer considered valid and the IC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne
peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera
chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une
autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed and operated with greater than 34cm between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains IC: 8205A-
MOD16370915”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où
l’antenne peut être installée et utilisée à plus de 34 cm entre l’antenne et les utilisateurs.
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 8205A-MOD16370915".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiqué dans ce manuel.
DETACHABLE ANTENNA USAGE
This radio transmitter (IC: 8205A-MOD16370915 / Model: MOD-16370-915) has been
approved by ISED to operate with the antenna type listed below with maximum
permissible gain indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Le présent émetteur radio (IC: 8205A-MOD16370915 / Model: MOD-16370-915) a été
approuvé par ISED pour fonctionner avec les types d'antenne énumérés ci-dessous et
ayant un gain admissible maximal. Les types d'antenne non inclus dans cette liste, et
dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
Approved antennas list:
Professional installation instruction
1. Installation personal
This product is designed for specific application and needs to be
installed by a qualified personal who has RF and related rule
knowledge. The general user shall not attempt to install or change the
setting.
2. Installation location
The product shall be installed at a location where the radiating
antenna can be kept 34cm from nearby person in normal operation
condition to meet regulatory RF exposure requirement.
3. External antenna
Use only the antennas which have been approved by the applicant. The
non-approved antenna(s) may produce unwanted spurious or excessive
RF transmitting power which may lead to the violation of FCC/IC limit
and is prohibited.
4. Installation procedure
Please refer to user’s manual for the detail.
5. Warning
Please carefully select the installation position and make sure that the
final output power does not exceed the limit set force in relevant
rules. The violation of the rule could lead to serious federal penalty.
Instructions d'installation professionnelle
1. Installation
Ce produit est destine a un usage specifique et doit etre installe par un
personnel qualifie maitrisant les radiofrequences et les regles s'y
rapportant. L'installation et les reglages ne doivent pas etre modifies
par l'utilisateur final.
2. Emplacement d'installation
En usage normal, afin de respecter les exigences reglementaires
concernant l'exposition aux radiofrequences, ce produit doit etre
installe de facon a respecter une distance de 34cm entre l'antenne
emettrice et les personnes.
3. Antenn externe.
Utiliser uniiquement les antennes approuvees par le fabricant.
L'utilisation d'autres antennes peut conduire a un niveau de
rayonnement essentiel ou non essentiel depassant les niveaux limites
definis par FCC/IC, ce qui est interdit.
4. Procedure d'installation
Consulter le manuel d'utilisation.
5. Avertissement
Choisir avec soin la position d'installation et s'assurer que la puissance
de sortie ne depasse pas les limites en vigueur. La violation de cette
regle peut conduire a de serieuses penalites federales.
Contents
1. Description
2. Mechanical Drawing
3. Specifications
4. Terminal Description
1. Description
MOD-16370-915 Module is designed by a high performance ultra-
low power RF transceiver, intended for RF wireless applications in
the sub-1 GHz band. And is operating in the license free ISM bands
2. Mechanical Drawing
3. Specifications
Operating Frequency
902.4 ~ 927.6MHz
Power Supply Rating
3.3VDC
Modulation Type
2-GFSK
Number of Channel
127
Output Power
242.661mW
Antenna Type
Refer to Note
Operating Temperature
-20℃ ~ +60℃
Note:
Following Antennas were provided for selection
4. Terminal Description
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
Omega MOD16370915 Sub-1G Module Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Autres documents
-
Gosund LB3 Manuel utilisateur
-
Lantronix Open-Q 865 Mode d'emploi
-
Microsoft 1889 Mode d'emploi
-
Microsoft 1884 Mode d'emploi
-
Realtek RTL8852B M.2 1216 Combo Module Manuel utilisateur
-
Mediatek MT7922A22M Mode d'emploi
-
Lantronix Open-Q Mode d'emploi
-
Dell RFID 13.56MHz Wireless Module Mode d'emploi
-
-
