Fisher & Paykel WH2424P1 Mode d'emploi

FRONT LOADING CLOTHES WASHER

WH2424F & WH2424P models

LAVEUSE À CHARGEMENT FRONTAL

Modèles WH2424F & WH2424P

INSTALLATION GUIDE / USER GUIDE

GUIDE D’INSTALLATION / GUIDE D’UTILISATION

US CA

English Page 1 – 52

Français

Page 55 – 106

1

CONTENTS

Introduction 3

Safety and warnings 4

Installation instructions 7

Before you do your first wash 17

Getting started 18

Washer controls 22

Safety features 23

Sorting and loading 24

Detergent and fabric softener 26

Wash cycles 30

Wash cycle options 32

Customizing wash cycles 36

Caring for your washer 37

Before you call for service 40

Fault codes 42

Troubleshooting 43

Limited warranty 49

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this User guide may

not be available in all markets and are

subject to change at any time. For current

details about model and specification

availability in your country, please go to

our website www.fisherpaykel.com or

contact your local Fisher & Paykel dealer.

Registration

Register your product with us so we can

provide you with the best service possible.

To register your product visit our website:

www.fisherpaykel.com

EN

7

INSTALLATION INSTRUCTIONS

Product dimensions

WH2424F

WH2424P

PRODUCT DIMENSIONS inches (mm)

AOverall height of product 331/2” (850)

BOverall width of product 235/8” (600)

COverall depth of product (including dial and door whenclosed) 255/8” (645)

DDepth of door open 42” (1065)

EMinimum door clearance to adjacent wall 13” (330)

Standpipe height min. 311/2” – 471/4”

(min. 800–1200)

CAPACITY

2.4 cu ft

Note: the exact height of your washer is dependent on how far the feet are extended

from the base of the machine. The space where you install your washer needs to be at

least 13/5” (40mm) wider and 3/4” (20mm) deeper than its dimensions.

●Electrical supply: 2 wire plus ground, 120V, single phase, 60Hz, alternating current.

●Inlet water static pressure: Max. (120psi), Min. 10psi.

●Inlet water flow rate at faucet: Min. 11/2 gallons/min (6liters/min).

E

D

A

B

C

TOP VIEWWallFRONT VIEW

EN

8

INSTALLATION INSTRUCTIONS

Accessories

Please check you received the following accessories with your Fisher & Paykel washer.

You will find them inside the drum or attached to the packaging.

●2 x Inlet hoses

●1 x Drain hose guide

●1 x Installation instructions and User guide

●1 x Wrench

●1 x Installation leaflet (attached to the top of the washer)

Unpacking

WARNING!

Recycle or destroy the carton and plastic bags after the washer is unpacked. Make

materials inaccessible to children. Children might use them for play. Cartons covered with

rugs, bedspreads or plastic sheets can become airtight chambers causing suffocation.

To ensure the best performance from your new washer please follow the instructions below.

Removing the packaging:

1 Remove the outer packaging. Note: a small amount of water may be seen inside the

packaging and inside the washer. This is the result of factory testing and is normal.

2 Tilt the machine backwards and ‘walk’ it off the base one foot at a time. Not doing so

may cause damage to your floor and washer.

3 Remove all packaging and accessories from inside the drum. Note: DO NOT remove the

screw or clip holding the hose.

Removing the transit bolts

The clothes washer is fitted with 4 transit bolts at the rear to avoid damage during

transportation.

IMPORTANT!

The 4 transit bolts MUST be removed prior to operation of the machine. Failure to

remove these will result in damage to the machine.

12

INSTALLATION INSTRUCTIONS

If you have an uncontrolled water heating source (eg a wet back or solar heating

system) you should fit a tempering valve. This will ensure the hot water temperature

remains within safe limits.

Contact your registered plumber to select and install the tempering valve.

IMPORTANT!

●This appliance must be installed in accordance with the installation instructions before use.

●Provide accessibility to the plug or incorporate a switch in the fixed wiring in

accordance with the wiring rules to allow disconnection of the appliance from the

supply after installation.

Water supply requirements

Hot and cold water faucets MUST be installed within 42” (107cm) of your washer’s

water inlet. The faucets MUST be 3/4” (1.9cm) garden hose-type so inlet hoses can be

connected. Water pressure MUST be between 10 and 120 pounds per square inch. Your

water department can advise you of your water pressure. The hot water temperature

should be set to deliver water at 120° to 140°F (48°–60°C) to provide proper

Automatic Temperature Control (ATC) performance.

15

INSTALLATION INSTRUCTIONS

IMPORTANT!

●If you are using an extension cord or a portable electrical outlet device (eg multi-

socket outlet box), ensure that it is positioned so that it does not come into contact

with water or moisture. FAILURE TO DO SO MAY RESULT IN DEATH OR ELECTRICAL

SHOCK.

●Do not touch or operate the machine with wet hands or with bare-feet.

●A damaged power cord must be replaced by a Fisher & Paykel trained and supported

service technician, in order to avoid a hazard. The appliance must not be operated

until it is repaired, as there is risk of electric shock.

●Do not operate this machine if it has been damaged during transport. Contact your

Fisher & Paykel dealer or Fisher & Paykel trained and supported service technician.

SPARE PARTS

Contact Customer Care 1.888.936.7872 or go on line to

www.fisherpaykel.com/customercare for spare parts information.

Drain Hose Extension

(Not suitable for attaching to a spigot).

Part No. 425627P

EN

17

BEFORE YOU DO YOUR FIRST WASH

Before you start, it is a good idea to go through the following checklist:

1 Have the packaging and transit bolts been removed?

2 Is the drain hose threaded through the ‘Ubend’ (with no more than 3/4” (20mm)

extended) and hooked into your standpipe or tub, or attached to a spigot?

3 Is the hot hose connected to the hot valve (color-coded orange, if present)? Is the

cold hose connected to the cold valve (color-coded white)? Have the faucets been

turned on?

4 Is the machine correctly leveled, feet are locked and cabinet corners clear of the floor

and walls?

5 Has the power cord been connected to an appropriate power supply and the power

turned on?

6 Have you performed the installation test cycle?

7 We recommend you complete your first cycle with a half-load amount of detergent

and without a load in order to remove any residues remaining in the machine from the

manufacturing process.

IMPORTANT!

You must ensure all 4transit bolts have been removed from your washer before you

start using it. If the transit bolts are not removed, they will damage your washer and

YOUR LIMITED WARRANTY WILL BE COMPROMISED.

EN

La page charge ...

Fisher & Paykel WH2424P1 Mode d'emploi

Ce manuel convient également à

Fisher & Paykel WH2424P1 Mode d'emploi

dans d''autres langues