DeWalt DCD710S2 Manuel utilisateur

Marque: DeWalt

Modèle: DCD710S2

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Ce manuel convient également à

DCD710S2 12V MAX Cordless

DCD710

3/8" (10mm) 12V Max* Cordless Adjustable Clutch Drill/Driver

Perceuse/visseuse à embrayage réglable, sans fil, de 10mm (3/8po) et 12V max*

Taladro/impulsor con embrague ajustable, inalámbrico de 10 mm (3/8") 12 V Máx*

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY DEWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another battery

pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

English

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing, grinding,

drilling, and other construction activities contains chemicals known

to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do

this type of work. To reduce your exposure to these chemicals: work

in a well ventilated area, and work with approved safety equipment,

such as those dust masks that are specially designed to filter out

microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction activities.

Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth, eyes, or lay on

the skin may promote absorption of harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other injury.

Always use NIOSH/OSHA approved respiratory protection appropriate

for the dust exposure. Direct particles away from face and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may contribute

to hearing loss.

CAUTION: When not in use, place tool on its side on a stable

surface where it will not cause a tripping or falling hazard.

Some tools with large battery packs will stand upright on the battery

pack but may be easily knocked over.

c) When battery pack is not in use, keep it away from other

metal objects, like paper clips, coins, keys, nails, screws,

or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety Rules for Drill/Drivers

• Use auxiliary handle(s), if supplied with the tool. Loss of

control can cause personal injury.

• Hold power tool by insulated gripping surfaces, when

performing an operation where the cutting accessory may

contact hidden wiring. Cutting accessory contacting a “live” wire

may make exposed metal parts of the power tool “live” and could

give the operator an electric shock.

• Use clamps or other practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body is unstable and may lead to loss of control.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

English

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust.

Inserting or removing the battery from the charger may ignite the

dust or fumes.

• NEVER force battery pack into charger. DO NOT modify

battery pack in any way to fit into a non-compatible charger

as battery pack may rupture causing serious personal injury.

Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in DEWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105 ˚F (40 ˚C)

(such as outside sheds or metal buildings in summer).

WARNING: Fire hazard. Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged, do not insert

into charger. Do not crush, drop or damage battery pack. Do not use a

battery pack or charger that has received a sharp blow, been dropped,

run over or damaged in any way (i.e., pierced with a nail, hit with a

hammer, stepped on). Damaged battery packs should be returned to

service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so

that metal objects can contact exposed battery terminals.

For example, do not place battery in aprons, pockets, tool boxes,

product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery

terminals inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations (HMR)

actually prohibit transporting batteries in commerce or on airplanes

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ................... volts A ......................amperes

Hz ................. hertz W ..................... watts

min ............... minutes or AC ..........alternating

or DC ... direct current current

................. Class I Construction or AC/DC ...alternating

.....................

(grounded) ........................or direct

................. Class II Construction current

(double insulated) no ....................no load

…/min ........... per minute speed

BPM ............. beats per minute

n ......................rated

IPM ............... impacts per minute ........................speed

RPM ............. revolutions per .....................earthing

minute terminal

sfpm .............surface feet ..................... safety alert

..................... per minute symbol

SPM .............strokes per minute

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include catalog

number and voltage. Consult the chart at the end of this manual for

compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below. Then

follow charging procedures outlined.

English

RBRC™, in cooperation with DEWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized DEWALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instruc tions for battery chargers.

• Before using charger, read all instructions and cautionary markings

on charger, battery pack, and product using battery pack.

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

DEWALT rechargeable batteries. Other types of batteries may burst

causing personal injury and damage.

NOTICE: Under certain conditions, with the charger plugged in to the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil, or any buildup of metallic

particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the

cavity. Unplug charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

(i.e., packed in suitcases and carry-on luggage) UNLESS they are

properly protected from short circuits. So when transporting individual

batteries, make sure that the battery terminals are protected and well

insulated from materials that could contact them and cause a short

circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for

15 minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persist, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs)

indicate that the costs to recycle these batteries (or

battery packs) at the end of their useful life have already

been paid by DEWALT. In some areas, it is illegal to

place spent nickel cadmium, nickel metal hydride or lithium ion

batteries in the trash or municipal solid waste stream and the RBRC

program provides an environmentally conscious alternative.

English

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug.

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble charger; take it to an authorized service

center when service or repair is required. Incorrect reassembly

may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect two chargers together.

• The charger is designed to operate on standard 120 volt

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

• These chargers are not intended for any uses other than

charging DEWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock, or electrocution.

• When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for outdoor

use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

English

DCB107, DCB112

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

HOT/COLD PACK DELAY

DCB107, DCB112

The DCB107 and DCB112 chargers have a hot/cold delay feature.

When the charger detects a battery that is hot, it automatically delays

charging until the battery has cooled. When the charger detects a

battery that is cold, it automatically delays charging until the battery

has warmed.

The red light will continue to blink, but a yellow indicator light will be

illuminated during this operation. Once the battery has cooled, the

yellow light will turn off and the charger will resume the charging

procedure.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions

before using your charger. Consult the chart on the back cover of this

manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate outlet before inserting

battery pack.

2. Insert the battery pack

FIG. 1

(H) into the charger, as

shown in Figure 1,

making sure the pack

is fully seated in

charger. The red

(charging) light will

blink continuously

indicating that the

charging process has

started.

3. The completion of

charge will be indicated

by the red light remaining ON continuously. The pack is fully

charged and may be used at this time or left in the charger.

Indicator Light Operation

DCB106

PACK CHARGING

PACK CHARGED

English

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug charger before

attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Never attempt to open the battery pack for any reason.

If the plastic housing of the battery pack breaks or cracks, return to a

service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct

sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

Wall Mounting

DCB107, DCB112

These chargers are designed to be wall mountable or to sit upright on

a table or work surface.

If wall mounting, locate the charger within reach of an electrical outlet.

Mount the charger securely using drywall screws at least 1" (25.4 mm)

long, screwed into wood to an optimal depth leaving approximately

7/32" (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65 ˚F

and 75 ˚F (18–24 ˚C). DO NOT charge the battery pack in air

temperature below +40 ˚F (+4.5 ˚C), or above +105 ˚F (+40.5 ˚C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to touch while

charging. This is a normal condition, and does not indicate a

problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65 ˚F–75 ˚F

(18–24 ˚C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

English

FIG. 2

COMPONENTS (Fig. 2)

WA R N I N G : Never modify the power tool or any part of it.

Damage or personal injury could result.

A. Variable speed trigger switch

B. Forward/reverse button

C. Worklight

D. Torque adjustment collar

E. Gear shifter

F. Keyless chuck

G. Battery release button

H. Battery pack

I. Belt hook (optional accessory)

J. Screw

INTENDED USE

This drill/driver is designed for light fastening and drilling applications.

DO NOT use under wet conditions or in presence of flammable

liquids or gases.

This drill/driver is a professional power tool. DO NOT let children

come into contact with the tool. Supervision is required when

inexperienced operators use this tool.

Belt Hook (Optional Accessory) (Fig. 2)

WARNING: To reduce the risk of serious personal injury,

place the forward/reverse button in the lock-off position

or turn tool off and disconnect battery pack before making

any adjustments or removing/installing attachments or

accessories.

WARNING: To reduce the risk of serious personal injury,

DO NOT suspend tool overhead or suspend objects from the belt

hook. ONLY hang tool’s belt hook from a work belt.

WARNING: To reduce the risk of serious personal injury,

ensure the screw holding the belt hook is secure.

IMPORTANT: When attaching or replacing the belt hook, use only

the screw (J) that is provided. Be sure to securely tighten screw.

English

Worklight (Fig. 2)

There is a worklight (C) located under the torque adjustment collar

(D). The worklight will be activated when the trigger switch is

squeezed.

NOTE: The worklight is for lighting the immediate work surface and

is not intended to be used as a flashlight.

Torque Adjustment Collar (Fig. 3)

The torque adjustment collar (D) is clearly

FIG. 3

marked with numbers and a drill bit symbol.

The collar should be rotated until the desired

setting is located at the top of the tool.

Locators are provided in the collar to eliminate

the guess work when selecting fastening

torque. The higher the number on the collar,

the higher the torque and the larger the

fastener which can be driven. To lock the

clutch for drilling operations, move to the drill

bit position.

NOTE: When using the drill/driver for drilling

holes, be sure that the torque adjusting collar

is set so the figure of the drill is aligned with

the center line on the top of the tool. Failure

to do this will allow the clutch to slip while

attempting to drill.

Dual Range Gearing (Fig. 3)

The dual range feature of your driver/drill allows you to shift gears for

greater versatility.

To select the low speed, high torque setting, turn the tool off and

permit to stop. Slide the gear shifter (E) forward (towards the chuck).

The belt hook (I) can be be attached to either side of the tool using

only the screw (J) provided, to accommodate left- or right-handed

users. If the hook is not desired at all, it can be removed from the

tool.

To move belt hook, remove the screw (J) that holds the belt hook

in place then reassemble on the opposite side. Be sure to securely

tighten screw.

Variable Speed Trigger Switch (Fig. 2)

To turn the tool on, squeeze the trigger switch (A). To turn the tool off,

release the trigger switch. Your tool is equipped with a brake. The

chuck will stop when the trigger switch is fully released.

The variable speed switch enables you to select the best speed for a

particular application. The further you squeeze the trigger, the faster

the tool will operate. For maximum tool life, use variable speed only

for starting holes or fasteners.

NOTE: Continuous use in variable speed range is not recommended.

It may damage the switch and should be avoided.

Forward/Reverse Control Button (Fig. 2)

A forward/reverse control button (B) determines the direction of the

tool and also serves as a lock off button. To select forward rotation,

release the trigger switch and depress the forward/reverse control

button on the right side of the tool. To select reverse, depress the

forward/reverse control button on the left side of the tool. The center

position of the control button locks the tool in the off position. When

changing the position of the control button, be sure the trigger is

released.

NOTE: The first time the tool is run after changing the direction of

rotation, you may hear a click on start up. This is normal and does not

indicate a problem.

English

To remove the battery pack from the tool, press the release button (G)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

Keyless Single Sleeve Chuck (Fig. 5)

Your tool features a keyless chuck with one rotating sleeve for one-

handed operation of the chuck. To insert a drill bit or other accessory,

follow these steps.

1. Lock the trigger in the OFF position as previously described.

2. Grasp the black sleeve of the chuck with one hand and use the

other hand to secure the tool. Rotate the sleeve counterclockwise

far enough to accept the desired accessory.

3. Insert the accessory about

FIG. 5

3/4" (19 mm) into the chuck and

tighten securely by rotating the

chuck sleeve clockwise with

one hand while holding the tool

with the other. Your tool is

equipped with an automatic

spindle lock mechanism. This

allows you to open and close

the chuck with one hand.

To release the accessory, repeat

step 2 above.

WARNING: Do not attempt to tighten drill bits (or any other

accessory) by gripping the front part of the chuck and turning the tool

on. Damage to the chuck and personal injury may result. Always lock

off trigger switch when changing acces sories.

Be sure to tighten chuck with one hand on the chuck sleeve and one

hand holding the tool for maximum tightness.

To select the high speed, low torque setting, turn the tool off and

permit to stop. Slide the gear shifter back (away from chuck).

NOTE: Do not change gears when the tool is running. If you are having

trouble changing gears, make sure that the dual range gear shifter is

either completely pushed forward or completely pushed back.

OPERATION

WARNING: To reduce the risk of serious personal injury,

place the forward/reverse button in the lock-off position

or turn tool off and disconnect battery pack before making

any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Installing and Removing the Battery Pack

(Fig. 4)

WARNING: To reduce the risk of injury, never depress the battery

release button without removing the battery pack. Depressing the

battery release button without removing the battery pack can result in

the battery pack falling out unexpectedly.

NOTE: For best results, make sure your battery pack is fully charged.

To install the battery pack (H) into the tool handle, align the battery

pack with the rails inside the tool’s handle and slide it into the handle

until the battery pack is firmly seated in the tool and ensure that it does

not disengage.

FIG. 4

English

CHUCK INSTALLATION (FIG. 7)

Screw the chuck on by hand as far as it will go and insert screw (left-

hand thread). Tighten screw securely. Tighten the chuck around

the shorter end of a 1/4" (6.4 mm) or larger hex key (not supplied)

strike the longer end in the clockwise direction with a wooden

mallet, as shown. Tighten the screw once again by turning in a

counterclockwise direction.

Drill Operation (Fig. 2)

WARNING: To reduce the risk of serious personal injury,

turn tool off and disconnect tool from power source before

making any adjustments or removing/installing attachments

or accessories. An accidental start-up can cause injury.

WARNING: To reduce the risk of personal injury, ALWAYS

ensure workpiece is anchored or clamped firmly. If drilling thin

material, use a wood “back-up” block to prevent damage to the

material.

Turn the collar (D) to the drill bit symbol for drilling. Select the desired

speed/torque range using the gear shifter (E) to match the speed and

torque to the planned operation.

1. Use sharp drill bits only. For WOOD, use twist drill bits, spade

bits, or hole saws. For METAL, use high-speed steel (HSS) twist

drill bits or hole saws.

2. Always apply pressure in a straight line with the bit. Use enough

pressure to keep drill biting, but do not push hard enough to

stall the motor or deflect the bit.

3. Hold tool firmly with both hands to control the twisting action of

the drill.

WA R N I N G: The drill may stall if overloaded causing a sudden

twist. Always expect the stall. Grip the drill firmly with both hands to

control the twisting action and avoid injury.

CHUCK REMOVAL (FIG. 6)

Turn the adjustment collar (D) to the “drill” position and gear shifter

(E) to position 1 (low speed). Tighten the chuck around the shorter

end of a hex key (not supplied) of 1/4" (6.4 mm) or greater size.

Using a wooden mallet or similar object, strike the longer end in

the clockwise direction, as shown. This will loosen the screw inside

the chuck.

Open chuck jaws fully, insert screwdriver (or Torx tool if required)

into front of chuck between jaws to engage screw head. Remove

screw by turning clockwise (left-hand-thread). Place hex key in

chuck and tighten, as shown in Figure 6. Using a wooden mallet or

similar object, strike key sharply in the counterclockwise direction.

This will loosen the chuck so that it can be unscrewed by hand.

FIG. 6 FIG. 7

English

MAINTENANCE

WARNING: To reduce the risk of serious personal injury,

place the forward/reverse button in the lock-off position

or turn tool off and disconnect battery pack before making

any adjustments or removing/installing attachments or

accessories. An accidental start-up can cause injury.

Cleaning

WARNING: Blow dirt and dust out of all air vents with clean, dry air

at least once a week. To minimize the risk of eye injury, always wear

ANSI Z87.1 approved eye protection when performing this.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do not

use water or any cleaning solutions.

Accessories

WARNING: Since accessories, other than those offered by DEWALT,

have not been tested with this product, use of such accessories with

this tool could be hazardous. To reduce the risk of injury, only DEWALT

recommended accessories should be used with this product.

Recommended accessories for use with your tool are available at

extra cost from your local dealer or authorized service center. If you

need assistance in locating any accessory, please contact DEWALT

Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286, call

1-800-4-DEWALT (1-800-433-9258) or visit our website: www.dewalt.

com.

4. IF DRILL STALLS, it is usually because it is being overloaded

or improperly used. RELEASE TRIGGER IMMEDIATELY,

remove drill bit from work, and determine cause of stalling. DO

NOT CLICK TRIGGER ON AND OFF IN AN ATTEMPT TO

START A STALLED DRILL — THIS CAN DAMAGE THE

DRILL.

5. To minimize stalling or breaking through the material, reduce

pressure on drill and ease the bit through the last fractional part

of the hole.

6. Keep the motor running when pulling the bit back out of a

drilled hole. This will help prevent jamming.

7. With variable speed drills there is no need to center punch

the point to be drilled. Use a slow speed to start the hole and

accelerate by squeezing the trigger harder when the hole is

deep enough to drill without the bit skipping out.

Operation as a Screwdriver (Fig. 2)

Select the desired speed/torque range using the dual range gear

shifter (E) on the top of tool to match the speed and torque to the

planned operation.

Insert the desired fastener accessory into the chuck (F) as you

would any drill bit. Make a few practice runs in scrap or unseen

areas to determine the proper position of the clutch collar(D).

MAXIMUM RECOMMENDED CAPACITIES

Low Range (1) High Range (2)

BITS, METAL DRILLING 1/4" (6.35 mm) 1/8" (3.18 mm)

WOOD, FLAT BORING 3/4" (19.05 mm) 1/2" (12.7 mm)

HOLE SAWS 3/4" (19.05 mm) 5/8" (15.88 mm)

English

In addition to the warranty, DEWALT tools are covered by our:

1 YEAR FREE SERVICE

DEWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120,

DCB201, DCB203, DCB207 and DCB127

3 YEARS FREE SERVICE ON DEWALT BATTERY PACKS

DCB200, DCB204

DEWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. DEWALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

DEWALT Power Tool, Laser, or Nailer for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund

– no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the local

company or see website for warranty information.

Repairs

The charger and battery pack are not serviceable.

To assure product SAFETY and RELIABILITY, repairs, maintenance and

adjustment (including brush inspection and replacement) should be

performed by a DEWALT factory service center, a DEWALT authorized

service center or other qualified service personnel. Always use

identical replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance loss,

such as fire, flood or theft, your registration of ownership will serve

as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-DEWALT (1-800-433-9258).

This warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. This warranty gives

you specific legal rights and you may have other rights which vary in

certain states or provinces.

English

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-DEWALT (1-800-433-

9258) for a free replacement.

Français

Déﬁ nitions: lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour

chaque mot-indicateur employé. Lire le mode d’emploi et porter

une attention particulière à ces symboles.

DANGER: indique une situation dangereuse imminente qui,

si elle n’est pas évitée, entraînera la mort ou des blessures

graves.

AVERTISSEMENT : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessures graves.

ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de

dommages corporels mais qui par contre, si rien n’est fait pour

l’éviter, pourrait poser des risques de dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL

OU DE TOUT AUTRE OUTIL DEWALT, COMPOSEZ LE NUMÉRO

SANS FRAIS : 1-800-4-DEWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire

le mode d’emploi de l’outil.

Avertissements de sécurité généraux

pour les outils électriques

AVERTISSEMENT! lire tous les avertissements de

sécurité et toutes les directives. Le non-respect des

avertissements et des directives pourrait se solder par un choc

électrique, un incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS

ET TOUTES LES DIRECTIVES POUR UN

USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte

à votre outil électrique à alimentation sur secteur (avec fil) ou par piles

(sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux

encombrés ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un

milieu déflagrant, tel qu’en présence de liquides, de

gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière

ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant

l’utilisation d’un outil électrique. Une distraction pourrait en

faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre

à la prise. Ne jamais modifier la fiche d’aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera

réduit par l’utilisation de fiches non modifiées correspondant à

la prise.

b) Éviter tout contact physique avec des surfaces mises à la

terre comme des tuyaux, des radiateurs, des cuisinières

et des réfrigérateurs. Le risque de choc électrique est plus

élevé si votre corps est mis à la terre.

Français

c) Empêcher les démarrages intempestifs. S’assurer que

l’interrupteur se trouve à la position d’arrêt avant de

relier l’outil à une source d’alimentation et/ou d’insérer

un bloc-piles, de ramasser ou de transporter l’outil.

Transporter un outil électrique alors que le doigt repose sur

l’interrupteur ou brancher un outil électrique dont l’interrupteur

est à la position de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer

l’outil. Une clé ou une clé de réglage attachée à une partie

pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en

tout temps. Cela permet de mieux maîtriser l’outil électrique

dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de

vêtements amples ni de bijoux. Garder les cheveux, les

vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de

rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de

dispositifs de dépoussiérage et de ramassage, s’assurer

que ceux-ci sont bien raccordés et utilisés. L’utilisation d’un

dispositif de dépoussiérage peut réduire les dangers engendrés

par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique

approprié à l’application. L’outil électrique approprié

effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur

est défectueux. Tout outil électrique dont l’interrupteur est

défectueux est dangereux et doit être réparé.

c) Ne pas exposer les outils électriques à la pluie ou à

l’humidité. La pénétration de l’eau dans un outil électrique

augmente le risque de choc électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher un

outil électrique. Tenir le cordon éloigné de la chaleur, de

l’huile, des bords tranchants et des pièces mobiles. Les

cordons endommagés ou enchevêtrés augmentent les risques

de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se

servir d’une rallonge convenant à cette application.

L’utilisation d’une rallonge conçue pour l’extérieur réduira les

risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique

dans un endroit humide, brancher l’outil dans une prise

ou sur un circuit d’alimentation dotés d’un disjoncteur de

fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve

de jugement lorsqu’un outil électrique est utilisé. Ne

pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un

simple moment d’inattention en utilisant un outil électrique peut

entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle.

Toujours porter une protection oculaire. L’utilisation

d’équipements de protection comme un masque antipoussière,

des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les

risques de blessures corporelles.

Français

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné

des objets métalliques, notamment des trombones, de

la monnaie, des clés, des clous, des vis ou autres petits

objets métalliques qui peuvent établir une connexion

entre les deux bornes. Le court-circuit des bornes du bloc-

piles risque de provoquer des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors

du bloc-piles; éviter tout contact avec ce liquide. Si un

contact accidentel se produit, laver à grande eau. Si le

liquide entre en contact avec les yeux, obtenir également

des soins médicaux. Le liquide qui gicle hors du bloc-piles

peut provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de rechange

identiques. Cela permettra de maintenir une utilisation

sécuritaire de l’outil électrique.

Règles de sécurité propres aux

perceuses/visseuses

• Utiliser la/les poignée(s) auxiliaire(s) si fournie(s) avec l’outil.

Une perte de contrôle de l’outil pourrait occasionner des dommages

corporels.

• Tenir l’outil par les surfaces isolées prévues à cet effet

pendant toute utilisation où l’organe de coupe pourrait

entrer en contact avec des fils électriques cachés. Tout

contact de l’organe de coupe avec un fil sous tension mettra les

parties métalliques exposées de l’outil sous tension et électrocutera

l’utilisateur.

• Utiliser des serre-joints, ou tout autre moyen, pour fixer

et immobiliser le matériau sur une surface stable. Tenir la

c) Débrancher la fiche de la source d’alimentation et/ou du

bloc-piles de l’outil électrique avant de faire tout réglage

ou changement d’accessoire ou avant de ranger l’outil.

Ces mesures préventives réduisent les risques de démarrage

accidentel de l’outil électrique.

d) Ranger les outils électriques hors de la portée des enfants

et ne permettre à aucune personne n’étant pas familière

avec un outil électrique ou son mode d’emploi d’utiliser

cet outil. Les outils électriques deviennent dangereux entre les

mains d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces

mobiles sont mal alignées ou coincées, si des pièces sont

brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique.

En cas de dommage, faire réparer l’outil électrique

avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés sont

moins susceptibles de se coincer et sont plus faciles à maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en tenant

compte des conditions de travail et du travail à effectuer.

L’utilisation d’un outil électrique pour toute opération autre que

celle pour laquelle il a été conçu est dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) Ne recharger l’outil qu’au moyen du chargeur précisé par

le fabricant. L’utilisation d’un chargeur qui convient à un type

de bloc-piles risque de provoquer un incendie s’il est utilisé avec

un autre type de b loc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-

piles conçus à cet effet. L’utilisation de tout autre bloc-piles

risque de causer des blessures ou un incendie.

La page charge ...

DeWalt DCD710S2 Manuel utilisateur

Marque: DeWalt

Modèle: DCD710S2

Catégorie: Perceuses mixtes sans fil

Taper: Manuel utilisateur

Ce manuel convient également à

DCD710S2 12V MAX Cordless

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCD710S2 User manual
español: DeWalt DCD710S2 Manual de usuario