Modern Forms WS-70018 Diplomat Mode d'emploi

Marque: Modern Forms

Modèle: WS-70018 Diplomat

Taper: Mode d'emploi

INSTALLATION INSTRUCTIONS



WS-70018





Phone (800) 526.2588

Fax (800) 526.2585



44 Harbor Park Drive

Port Washington, NY 11050



1600 Distribution Ct

Lithia Springs, GA 30122



1750 Archibald Avenue

Ontario, CA 91760





• Read all instructions before installing.

• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

• Retain installation instructions for future maintenance reference.

All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern

Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any

parts are damaged or missing.

Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal

areas clean all external surfaces of the xture once every two weeks with a wet cloth.

Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.

• Lisez toutes les instructions avant l’installation.

• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux

règlements locaux.

• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement

avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus

pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la

garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

 Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons

aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec

un chion humide.

Wire Connector

Qty: 3 PCS+1Extra

Mounting Screw

Qty: 1Extra

Knurling Screw

Qty: 2PCS+1Extra

$ (

Fix Screw

Qty: 2PCS+1Extra

Gasket

Qty: 4PCS+1Extra

Plastic Anchor

Qty: 1PC+1Extra

Wood Screw

Qty: 1PC+1Extra

) *

INSTALLATION INSTRUCTIONS

WS-70018

Fixture Wires

Black or

Smooth

Fixture Wires

White or

Ribbed

Fixture Wires

Bare wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground)

Phone (800) 526.2588

Fax (800) 526.2585

44 Harbor Park Drive

Port Washington, NY 11050

1600 Distribution Ct

Lithia Springs, GA 30122

1750 Archibald Avenue

Ontario, CA 91760

parts on a clear area. Be careful not to lose any small

parts necessary for installation.

4. Drill holes in the wall aligned with the key holes located in the U bracket,

insert the plastic anchors (F).

5. Secure the mounting back plate to the junction box using standard

junction box screws that comes with the junction box.

Note: (i)using any other non-original- manufacturer Provided junction box

screw may result in safty issue;

(ii) The side of the mounting plate marked “GND” must face out.

6. Connect the driver’s input wires to junction box wires as shown in

Fig. 2,making sure that all wire connectors (A) are secured. If your outlet

wires are connected,

tuck them carefully inside the junction box.

7. Secure the U bracket to the wall by fastening the wood screws (G) to the plastic anchors (F),When you think the gap between the down

canopy and the wall is too large.T his is an optional step

10. Place the shade cover on the notch of the lamp body.

ing wires

information.

13. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).

14. To utilize 0-10V dimming: use wire purple (dim+), Pink or gray (dim-), black (hot), white (neutral) and bare copper ground wire (ground).

Ground Wire Mounting

Backplate

Acrylic

(

RPL-GLA-70018

)

SHADE

(RPL-SHA-70018)

Knurling Screw

Fix Screw

Mounting

Screw

Gasket

Plastic Anchor

Wood Screw

Driver:

5 3/10"[L] x 2 3 /5"[W] x 3/5"[H]

urple - Dim-

Pink or Gray - Dim-

Black - To Fixture -

Red - To Fixture + Green - Ground

White - Neutral

Black - Hot

Wire

Connector

Junction Box

Modern Forms WS-70018 Diplomat Mode d'emploi

Marque: Modern Forms

Modèle: WS-70018 Diplomat

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Modern Forms WS-70018 Diplomat Operating instructions

Modern Forms WS-70018 Diplomat Mode d'emploi

Modern Forms WS-70018 Diplomat Mode d'emploi

dans d''autres langues

Documents connexes