Big Ass Fans F-EV1-1001S75V60 Guide d'installation

Marque: Big Ass Fans

Modèle: F-EV1-1001S75V60

Taper: Guide d'installation

Ce manuel convient également à

BIGASSFANS.COM

COLD FRONT 100

COLD FRONT 200

EXCEPTIONALLY

ENGINEERED

READ AND SAVE THESE INSTRUCTIONS

LISEZ ET CONSERVEZ CES INSTRUCTIONS

LEA Y GUARDE ESTAS INSTRUCCIONES

Operation and Maintenance Manual

Manuel de fonctionnement et d'entretien

Manual de operación y mantenimiento

F-EV1-1001S75

F-EV1-1001S75V60

READ AND SAVE THESE INSTRUCTIONS

DANGER

DANGER indicates an imminently hazardous

situation which, if not avoided, WILL result in

death or serious injury.

WARNING

WARNING indicates a potentially hazardous

situation which, if not avoided, COULD

result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous

situation which, if not avoided, MAY result in

minor or moderate injury.

IMPORTANT

IMPORTANT indicates a potentially

hazardous situation which, if not avoided,

MAY result in property damage.

Installation Guide

Rev. C

09/22/2020

Improper installation, delivery, or maintenance, including, but not limited to, any of the following actions by

the customer or agent of the customer will constitute a breach of and will void all warranties:

• Failure to follow the required installation procedures speciﬁed in this Installation Guide and in

all other documentation supplied with the fans and related equipment including documentation

provided by the manufacturers of the individual fan and control components;

• Failure to follow all relevant codes and ordinances, including, but not limited to, the National

Electrical Code (United States), applicable national and local electrical codes, and state and local

building codes;

• Failure to follow electrical engineering industry standards regarding the approved method of

installing solid-state electrical equipment having the characteristics of the fans, the fan controls, and

their related components, even if such standards are not speciﬁcally referenced in any instructions or

literature supplied by Big Ass Fans or provided by manufacturers.

All trademarks used herein are the properties of their respective owners. No part of this document may

be reproduced or translated into a dierent language without the prior written consent of Big Ass Fans.

The information contained in this document is subject to change without notice. For the most up-to-date

information, see the online printable installation guide at www.bigassfans.com

Patent: www.bigassfans.com/patents • www.bigassfans.com/product-warranties

Original English Instructions www.bigassfans.com/support

CHECKLIST

✓ Read the Operation and Maintenance Manual.

✓ Check all hose connections.

✓ Use a 12 gauge cord if the cord is under 50 ft (15 m) or a 10 gauge

cord if the cord is over 50 ft (15 m).

✓ Provide fresh air intake for the cooler and maintain a minimum

clearance of 3 ft (0.9m) behind the cooler.

✓ Flush new cooling media.

1. Fill the cooler with water.

2. Switch on the pump.

3. Run the cooler without the fan running for 5 hours.

✓ Make sure the cooling media is being evenly saturated.

✓ Drain and clean the cooler weekly. Remove the cooling media and

wash with a garden hose.

✓ Use Refresh™ tablets (algae killer) and/or CTT-EC™ cooler treatment

tablets (mineral treatment). One algae killer tablet is provided in the

cooler's reservoir. Additional water treatment tablets are available

at bigassfans.com.

DO NOT

Χ DO NOT forget to dry out the cooling media before shutting down

the cooler. Turn o the pump and leave the fan running for 10 to 15

minutes.

Χ DO NOT run the pump without ﬁlling the reservoir with water ﬁrst.

Χ DO NOT use a water source with more than 120 PSI of water

pressure.

Χ DO NOT operate the cooler in a sealed room. Allow for fresh air

intake and exhaust.

ASSEMBLY

IMPORTANT

Carefully examine the carton for damage before opening. If the carton is

damaged, notify the shipping company immediately.

Install casters

1. Locate the package of four (4) casters and remove from box.

2. Lay box on its side and carefully open bottom of box. DO NOT STAND BOX

UPSIDE DOWN.

3. Install the four casters.

4. Stand cooler up on casters and remove box.

SETUP

The cooler has been factory tested and is ready to use. Place the cooler on level

ground with the casters locked to prevent inadvertent movement.

Connecting the water supply

The cooler comes equipped with a female garden hose water source connection.

Use a standard garden hose (not provided) to connect the water supply to the

cooler.

CAUTION

Do not connect to any water source where water pressure exceeds 120 PSI.

This will cause permanent damage to the cooler.

Connecting the electrical supply

IMPORTANT

The cooler should be plugged into a fused or breaker-protected circuit. Refer

to Table 1 for circuit size requirements.

Amperage and Circuit Requirements

Model Volts +/- 10% Frequency Min. Circuit Size

Running

Amps

Cold Front 100 120 V 60 Hz 15 A 1.5 A

Cold Front 200 120 V 60 Hz 15 A 2.7 A

Table 1: Electrical Requirements

CAUTION

Do not exceed the amperage ratings of the extension cord. Undersized

extension cords create excessive drops in voltage, causing the electric motor

to generate excess heat. This results in inecient motor operation and

premature motor failure and will void the warranty.

Three-Conductor Heavy Duty Extension Cord Requirements

Cord

Length

Cord Size

16 GA 14 GA 12 GA 10 GA

0–50 ft

(0–15 m)

13 A 18 A 25 A 30 A

50–100 ft

(15–30 m)

10 A 13 A 18 A 25 A

Table 2: Cord Size Requirements

OPERATION

The cooler must be placed on level ground to operate correctly. Evaporative

coolers create an oval-shaped air pattern. Obstacles such as racks and

workbenches may interfere with airﬂow. Position the cooler so that interruption

of the air pattern is minimized. Multiple coolers may be required to cover larger

areas.

There are three major factors to consider when determining where to place the

cooler.

1. Fresh Air Supply. The inlet (mesh sides) requires a constant, uninterrupted

supply of fresh air for maximum performance. A distance of 3 ft (0.9 m)

of clear space to any obstructions at the rear or inlet side of the cooler is

recommended.

2. Discharge Airﬂow. The cool air discharged from the cooler should be free from

obstruction to promote air circulation in order to maximize the cooling zone.

3. Ventilation. Adequate ventilation is needed to ensure the cooler does not

recirculate air that has already been through the evaporative cooling process.

Filling the cooler with water

Once the cooler has been connected to a water source, turn the water source on

to ﬁll the cooler with water. The ﬂoat valve will shut o the water ﬂow when the

sump is full.

CAUTION

Prolonged use of hard water without proper water treatment will create

mineral deposit buildup. This will cause the pump to fail and is NOT

COVERED BY WARRANTY.

Starting the pump

On initial startup, the cooling media in your new cooler will take a few hours to

become fully saturated. During this time, the media may produce an odor. This

odor will dissipate over time. For best results, change the water in the reservoir a

few times.

Subsequent startups

On subsequent startups, turn on the pump, start the fan, and cool down.

Low water indicator

The cooler is equipped with a low water indicator light.

♦ When the power is on and there is sucient water in the reservoir, the light will

be green and the pump will be running.

♦ When the power is on and the water in the reservoir is low, the light will be red

and the pump will stop running.

Starting the fan

Turn the fan control knob clockwise to turn on the fan and adjust the speed to

your preferred setting.

MAINTENANCE AND STORAGE

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect the power supply before performing any service or maintenance.

Failure to do so may result in serious injury or death.

Removing the cooling media

Remove the cooling pads to access the inside of the cooler.

1. Remove pad grilles from support channel.

2. Tilt pads from the top and lift out of the cooler.

Daily maintenance

After each use, turn o the pump about 15 minutes before the fan is turned o to

allow the pads to drain and dry out. This controls mildew and bacteria growth for a

long and ecient pad life. Drain the water from the cooler if it will be unused for a

prolonged period of time.

Periodic maintenance

The cooling pads act as a ﬁlter to remove dust and other particles from the

incoming air stream. The collected particles and any water impurities will ﬂow into

the sump and collect there. To keep the cooler operating at peak eciency, keep

the cooling media and sump clear of debris. Water treatment tablets are available

at bigassfans.com.

Draining the water sump

Depending on how often you operate the cooler, drain the sump anywhere from

every week for heavy use to monthly for light use.

1. Turn cooler o and disconnect the power supply.

2. Remove drain plug located at bottom of reservoir and let cooler drain.

3. Remove cooling pads.

4. Clean out reservoir with either a towel or wet/dry vacuum.

5. Reinstall pads and grille.

Cleaning the cooling media

Ensure the cooling pads are kept clean and dust-free. Dust and other particles

have an adverse eect on the pads’ ability to introduce water into the air stream. If

the pad surface is dirty, clean with a soft brush and water. Never use bleach.

Storage

1. Remove cooling pads and clean with a soft brush and water to remove dust

and debris.

2. Drain sump and wipe dry.

3. Store cooler in a dry area and cover to prevent dust buildup.

TROUBLESHOOTING AND REPAIR

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect the power supply before performing any service or maintenance.

Failure to do so may result in serious injury or death.

CAUTION

Please use caution when troubleshooting or repairing all electrical

components. Ensure all power is disconnected from the cooler before the

pads or fan guard are removed to gain access to the fan.

Tools needed

• Screwdrivers

• Pliers

• Adjustable wrenches

• Volt/Ohm meter (electrical troubleshooting)

Additional tools may be required.

General troubleshooting

The cooler consists of three systems:

• Pump

• Water distribution system

• Fan system

Use the troubleshooting tables on the following pages to determine which

system(s) require servicing.

Pump troubleshooting

Issue Solution(s)

Pump motor will not run

when switch is turned on.

Turn fan on to check for power.

• If fan does not start, check breaker and make

sure cord is plugged in.

• If fan starts, check for power to and through

pump switch (when turned on).

Ensure water level is high enough to make the

low water cuto circuit.

Fill water reservoir.

Pump motor hums when

switch is turned on but does

not pump water.

Obstruction in impeller.

Remove object(s).

Pump motor failure.

Replace pump.

Breaker trips or fuse blows

when switch is turned on.

Check power cord length and breaker rating.

Refer to page 2 for cooler amperage draw and

to determine required cord gauge and circuit

size.

Check for locked up pump.

Replace pump.

Pump runs but does not

pump water.

Air lock in outlet side of pump.

Turn o and on to bleed.

Ensure the impeller is turning in pump.

If not, replace pump.

Pump repair procedures

CAUTION

Repairs should be performed by a qualiﬁed technician!

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect the power supply before performing any service or maintenance.

Failure to do so may result in serious injury or death.

Pump replacement

1. Remove cooling pads.

2. Remove switch plate and disconnect pump wire. Refer to wiring diagram on the

following page.

3. Remove hose and level switch from pump.

4. Remove pump from water sump and install new pump.

5. Perform the steps above in reverse to reconnect the wiring, level switch, and

hose. Secure wires to fan frame with wire ties so that wires are clear of fan

blades. Ensure plug is positioned correctly.

6. Reinstall cooling pads and guards.

7. Reconnect power and test pump.

Water distribution system troubleshooting

The water distribution system consists of two assemblies:

• Water inlet assembly

– Brass bulkhead ﬁtting

– Float valve assembly

• Hose and valve assembly

– Drip channel

– Valve assembly

– Connection hose

Issue Solution(s)

Floor at side of cooler is wet. Water inlet hose is loose at supply hose or inlet

hose is loose at bulkhead ﬁtting.

Tighten connections and/or replace hose

washers.

Water overﬂows from

reservoir.

Float valve hose is loose at bulkhead ﬁtting or

at ﬂoat valve.

Tighten connections and/or replace hose

washers.

Water pressure is too high to allow ﬂoat valve

to shut o (120 PSI max).

Reduce water pressure by adding an inline

reducer.

Float valve is not properly seated.

Check all hoses for leaks.

Water is spitting from the

cooler.

Check the hose and valve assembly.

• Reduce ﬂow control setting.

• Replace cracked hose and valve assembly.

• Tighten hose connections.

Water is leaking from the

drain plug.

Check that plug is tightly seated in hole.

• Tighten drain plug.

• Replace drain plug.

There are too many dry

streaks on the pads.

Check for blocked holes in the drip channel.

• Remove and clean tube and holes.

Cooler will not ﬁll. Check ﬂoat screen.

Clean.

Float not functioning.

Replace.

Fan system troubleshooting

Issue Solution(s)

Fan will not run and makes

no sound.

Check power cord, extension cord, switches,

and circuit breaker.

• Reconnect power or extension cord.

• Reset breaker.

Fan will not run and makes

humming sound.

Check capacitor.

Re-center blade hub.

Motor stall (will not turn by hand).

Replace motor.

Breaker trips or fuse blows

when fan starts.

Motor stall.

Replace motor.

Check power source. Refer to page 2 for

electrical requirements.

Upgrade power supply.

Extension cord gauge is too small.

Replace with heavier cord.

Motor overheats, shuts o,

and restarts several minutes

later.

Extension cord gauge is too small.

Replace with heavier cord.

Inlet air is obstructed or too close to wall.

Provide minimum 3 ft (0.9 m) inlet clearance.

Faulty motor.

Replace motor.

Fan motor will not run and

switch makes soft clicking

sound.

Ensure switch is making good contact.

Replace switch if needed.

Fan blade does not turn

and cooler makes squealing

sound.

Motor stall (will not turn by hand).

Replace motor.

Fan will not reach speed but

turns and makes humming

sound.

Check capacitor (where visible) and motor

electrical connections.

Replace capacitor or motor.

Extension cord gauge is too small.

Replace with heavier cord.

Fan repair procedures

CAUTION

Repairs should be performed by a qualiﬁed technician!

WARNING

ELECTRICAL SHOCK HAZARD

Disconnect the power supply before performing any service or maintenance.

Failure to do so may result in serious injury or death.

Fan motor replacement

1. Remove cooling pads.

2. Remove black motor wiring plate and disconnect motor wires. Mark each wire

with a marker or marker tape for easy matching when installing new motor.

3. Remove louver.

4. Remove the four (4) nuts and bolts securing the motor, fan, and support braces

(complete fan assembly).

5. Replace with new fan assembly.

6. Secure with four (4) nuts and bolts.

7. Replace any wire ties that were removed when uninstalling the old fan

assembly.

8. Replace black motor wiring plate.

9. Reinstall pads and connect power.

Wiring diagram

1314

FAN

120V

PUMP

LOW LEVEL

SWITCH

FAN

VARIABLE SPEED

SWITCH

PUMP SWITCH

INDICATOR LIGHT

GREEN

BLACK

RED

BLACK

WHITE

BLUE

BLACK

GREEN

WHITE

GREEN

WHITE

GREEN

WHITE

BLACK

MAINTENANCE

Spring cleaning

☑ Remove the cooling media and clean out any debris in the

water pan at the bottom of the cooler.

☑ Remove the distribution tube from the mounting clips.

Remove the plug at the end of the tube and ﬂush out.

Clean the distribution holes with a small brush and ﬂush

with water to verify all holes are clear.

☑ If the cooling media is heavily stained with minerals or is

damaged, replace the media. Replacement cooling media

is available at bigassfans.com. Verify the media is installed

correctly with the arrows on the side.

☑ Connect the water line and turn on the water supply.

Check the ﬂoat valve and make sure it is operating

properly. Verify that the ﬂoat valve is shutting the water o

before walking away.

☑ Switch on the fan motor and pump. Make sure the cooling

media is being evenly saturated with water. Small dry

streaks are acceptable.

Mid-summer checkup

☑ Make sure the ﬂoat valve is working properly. If the valve

sticks, the water will run continuously and ﬂood the

reservoir. If this occurs, install a new ﬂoat valve or contact

Customer Service.

☑ Check all other working parts for cracks or damage,

including the pump, fan motor, and fan belt.

☑ Check the condition of the cooling media. The cooler runs

most eciently when the media is clean. If the media has

a heavy accumulation of mineral deposits, replace it.

☑ Use the drain valve to empty the reservoir. Remove any

debris.

Winterize

☑ Clean the minerals from the reservoir. Vinegar can be

used to dissolve buildup. Flush out the reservoir through

the drain plug.

☑ Inspect the water distribution tube for clogged holes.

Clean as necessary.

☑ To prevent freezing in the cooler’s water line, disconnect

the water supply, and then open both valves on the side

of the cooler to dry out the reservoir.

☑ Use a storage cover to protect your cooler and keep it

clean.

Customer Service

2348 Innovation Drive

Lexington, KY 40511

USA

877-244-3267

bigassfans.com

www.bigassfans.com/support

Accessories and Replacement Parts

www.bigassfans.com

FRANÇAIS

LISEZ ET CONSERVEZ CES INSTRUCTIONS

DANGER

DANGER indique une situation

imminente dangereuse qui, si elle

n'est pas évitée, ENTRAÎNERA une

blessure grave ou mortelle.

AVERTISSEMENT

AVERTISSEMENT indique

une situation potentiellement

dangereuse qui, si elle n'est pas

évitée, PEUT entraîner une blessure

grave ou mortelle.

ATTENTION

ATTENTION indique une situation

potentiellement dangereuse qui, si

elle n'est pas évitée, PEUT entraîner

une blessure mineure ou modérée.

IMPORTANT

IMPORTANT indique une situation

potentiellement dangereuse qui, si

elle n'est pas évitée, PEUT entraîner

des dommages à la propriété.

Guide d'installation

Rév. C

09/22/2020

Une installation, une livraison ou un entretien non conforme, incluant, sans s'y limiter, l'une des actions

suivantes par le client ou son agent constitue une violation de toutes les garanties et les rendra nulles :

• Le fait de ne pas suivre les procédures d'installation requises précisées dans ce guide d'installation

et dans toute autre documentation fournie avec les ventilateurs et l'équipement connexe incluant la

documentation fournie par le fabricant du ventilateur et des composants de commandes individuels;

• Le fait de ne pas suivre tous les codes et règlements applicables incluant, sans toutefois s'y limiter, le

National Electrical Code (États-Unis), les codes de l'électricité nationaux ou locaux applicables et les

codes du bâtiment de l'État ou locaux;

• Le fait de ne pas suivre les normes industrielles de l'électrotechnique sur la méthode approuvée de

l'installation de l'équipement électrique ayant les caractéristiques des ventilateurs, des commandes

du ventilateur et leurs composants connexes, même si ces normes ne sont pas mentionnées

spéciﬁquement dans toutes les instructions ou toute la documentation fournie par Big Ass Fans ou

par les fabricants.

Toutes les marques de commerce mentionnées ici appartiennent à leurs propriétaires respectifs.

Aucune partie de ce document ne peut être reproduite ou traduite dans une autre langue sans l'accord

préalable écrite de Big Ass Fans. Les renseignements contenus dans ce document peuvent être modiﬁés

sans préavis. Pour obtenir les informations les plus récentes, veuillez consultez le guide d'installation

imprimable au www.bigassfans.com

Brevet : www.bigassfans.com/patents • www.bigassfans.com/product-warranties

Instructions originales en anglais www.bigassfans.com/support

La page charge ...

Big Ass Fans F-EV1-1001S75V60 Guide d'installation

Marque: Big Ass Fans

Modèle: F-EV1-1001S75V60

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Big Ass Fans F-EV1-1001S75V60 Installation guide
español: Big Ass Fans F-EV1-1001S75V60 Guía de instalación

Big Ass Fans F-EV1-1001S75V60 Guide d'installation

Ce manuel convient également à

Big Ass Fans F-EV1-1001S75V60 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents