Brandt TE516XS1 Le manuel du propriétaire

Taper
Le manuel du propriétaire
Semi-fast
burner
Auxiliary
burner
Fast
burner
Extra-fast
burner
4 gas rings
+ double crown
4 gas rings
with extra-fast
Semi-fast
burner
Auxiliary
burner
Fast
burner
Double-crown
burner
3 gas rings
+ 1 electric hotplate
Electric
hotplate
Auxiliary
burner
Fast
burner
Extra-fast
burner
Hob operating guide
O guia de utilização da sua placa de cozinha
Ï ïäçãüò ÷ñÞóçò ôùí åóôéþí ôçò êïõæßíáò óáò
GR
PT
GB
99633581_ML_C.qxd 14/12/04 15:36 Page 1
2
In this Manual,
displays safety instructions
displays tips and hints
Contents
Using your hob in complete safety 4
What your hob looks like? 5
Installing your hob in all simplicity 6
Fitting recommendations 6-8
Electrical connections 9
Gas connections 10-11
Changing the type of gas supply 12-15
Using your hob in all simplicity 16
How to use your gas burners? 16
Which pans are best adapted for use on the gas burner 17
How to use the electric hotplate? 18
Which pans are best adapted for use on the electric hotplate? 18
How to look after your hob? 19
Minor troubleshooting 20
Gas-cooking guide 21
Electric hotplate-cooking guide 21
GB
99633581_ML_C.qxd 14/12/04 15:36 Page 2
3
Dear Customer,
Thank you for buying a BRANDT hob.
Our design staff have produced a new generation of kitchen
equipment, to make everyday cooking a pleasure.
You will find that the clean lines and modern look of your Brandt
hob blends in perfectly with your kitchen décor. It is easy to use
and performs to a high standard.
Brandt also makes a range of products that will enhance your
kitchen such as hobs, extractor hoods, built-in dishwashers and
refrigerators. There are models to complement your new Brandt
hob.
Of course, we make every effort to ensure that our products meet
all your requirements, and our Customer Service department is at
your disposal, to answer all your questions and to listen to all
your suggestions.
Brandt has always been a leader in the development of new
products, thus enhancing the quality of everyday life by providing
increasingly
efficient products, that are easy to use, respect the environment,
and are attractive and reliable.
The BRANDT name.
Editorial
99633581_ML_C.qxd 14/12/04 15:36 Page 3
4
We have designed your hob for
private domestic use.
With a view to the constant
improvement of our products, we
reserve the right to make any
changes in their technical, functional
or aesthetic characteristics as a result
of technical evolution.
These hobs are designed exclusively
for the cooking of drinks and
foodstuffs. These products do not
contain any asbestos-based
component parts.
You must always keep an eye on your
cooking.
Read the instructions before installing
and using the apparatus.
Never leave any
CLEANING or
INFLAMMABLE products in the
cupboard beneath your hob (aerosols
or other pressurised cans, papers,
recipe books, etc.).
Using a gas-powered hob produces
both heat and humidity in the room
where it is used. Make sure your
kitchen is well ventilated.
Keep all natural ventilation inlets
open or install a mechanical
ventilation device. Intensive and
Your hob in complete safety
prolonged use of this appliance may
require additional ventilation, (for
example by opening the window), or
more effective ventilation (for
example by increasing the power of
the mechanical ventilation if this
exists).
Disconnect your hob from both
electrical and gas supplies before
carrying out any maintenance
operations.
For safety reasons, do not forget to
close the main gas valve for built in
gas lines or the valve on the top of
your butane/propane gas cylinder.
The connector pipe should remain
accessible along its entire length and
must be replaced before its expiration
date (marked on the pipe).
Regardless of the means of
connection chosen, ensure that this is
totally free of leaks following
installation using soapy water.
If a knob is difficult to turn,
DO NOT
FORCE IT
. Call up your installer.
The EC mark of conformity can be
found on all these hobs.
Using your hob in complete safety
Y
OUR HOB IS DELIVERED PRE-SET FOR USE WITH NATURAL TOWN GAS.
99633581_ML_C.qxd 14/12/04 15:36 Page 4
5
What your hob looks like?
Electric
hotplate
Fast
burner
Semi-fast
burner
Auxiliary
burner
Fast
burner
Knob for back right gas ring
Knob for back left gas ring
Knob for front left gas ring
Knob for front right gas ring
Extra-fast
burner
Auxiliary
burner
Extra-fast
burner
Semi-fast
burner
Auxiliary
burner
Fast
burner
Double-crown
burner
Knob for back right gas ring
Knob for back left gas ring
Knob for front left gas ring
Knob for front right gas ring
Warning light electric hotplate
Knob for back right gas ring
Knob for front right gas ring
Knob for the back left hotplate
Knob for front left gas ring
99633581_ML_C.qxd 14/12/04 15:36 Page 5
6
This appliance should be installed by
a qualified technician / installer.
Prior to installation, ensure that the
local distribution conditions (nature
of the gas and gas pressure) and the
adjustment conditions of the
appliance are compatible.
These hobs are designed to be used by
private individuals in their homes.
The adjustment conditions are stated on
a label in the wallet and also on the
packaging.
This appliance must be installed and
connected in compliance with the
regulations in force, and used only in a
well-ventilated area. Consult the
instructions before installing and using
this appliance.
Installing your hob in all simplicity
Since this appliance is not connected to a
combustion products evacuation device.
Particular attention should be given to the
relevant requirements regarding
ventilation.
On this subject, combustion can take
place only if oxygen from the air is
present, so this air must be constantly
renewed and the combustion products
must be evacuated (a minimum air input
of 2 m3/hour per kw of gas energy is
required).
These hobs have type X protection (in
accordance with standard EN 60.335.2.6)
against overheating of cupboards and
Class 3 for installation itself (in
accordance with standard EN 30.1.1).
Fitting recommendations
Standard cutout
Model
Width
Depth Height
Depending on the unit
Outside
dimensions above
the work surface
60 cm
53 cm
5,8 cm
Outside
dimensions below
the work surface.
55 cm 47,5 cm 3,4 cm
49 cm
56 cm
99633581_ML_C.qxd 14/12/04 15:37 Page 6
7
Installing your hob in all simplicity
The hob must be built into the work-
top of a support cupboard. This work-
top must be at least 3 cm thick and
heat-resistant or else coated with a
heat resistant material.
A side-clearance of at least 30 cm
should be left to the right and left of
the hob. A tall cupboard or partition
too close to the hob would hinder free
movement of kitchen utensils.
If a horizontal partition is put under
the hob, it must be placed between 10
and 15 cm from the bottom of the
work top. In any case, do not keep
any sprays or pressurized containers
in the compartment which could be
just under the hob.
To ensure the seal between the hob
and the worktop, affix the joint provi-
ded in the folder before installing the
hob:
1- Remove the pan support grates, the
burner caps and heads after checking
their position.
2- Turn the hob over and place it gently
over the opening in the worktop paying
attention not to damage the control
knobs and lighters.
3- Stick the foam seal around the out-
side of the hob.
4- Put the hob back the right way up
and place the burners, caps and pan
grates back in position.
Fitting recommendations (cont'd)
49 cm
3 cm mini
30 cm
m
ini
30 cm
m
ini
56 cm / 26,5 cm
5,3 cm mini
70 cm mini
Underneath the hob (carter)
Seal
Fixing lugs FRONT
Fixing lugs BACK
99633581_ML_C.qxd 14/12/04 15:37 Page 7
8
Installing your hob in all simplicity
- Place the hob in position in the cutout
on the worktop, pulling it forward as far
as possible.
- Put the burners, caps and pan grates
in place.
- Connect the hob power supply cable
to the electrical installation of the kit-
chen. (See "Electrical connections" ).
- Connect to the gas (see "How to
connect the hob to mains gas" or
"How to connect the hob to butane
/ propane gas".
If you wish you can lock the hob into
position using attachments that come
with screws (see picture opposite) and
are secured to the corners of the
housing.
Only use the holes provided.
Stop screwing when the lug starts
to bend.
Do not use a power screwdriver.
Fitting recommendations (cont'd)
Underneath the hob (carter)
Seal
Worktop
Fixing lugs
Fixing lugs FRONT
Fixing lugs B
ACK
99633581_ML_C.qxd 14/12/04 15:37 Page 8
9
Cable H05VVF - T105
or H05V2V2F - T90
Cross section of
conductors in mm2
Fuse
220-240 V~- 50 Hz
All-gas and mixed
3 conductors of
which 1 is to be
earthed
1
10 A
CROSS SECTION OF THE CABLE TO USE
Installing your hob in all simplicity
Hobs are delivered with a three-
conductor (phase + ground + neutral)
H05VVF- T105 or H05V2V2F - T90
1mm section cable, ref. SAV :
77X3767 (6470.1516) and must be
connected to a 220-240 V~ single pha-
se mains supply by the intermediary of
a two phase + earth + CEI 60083
standardised neutral plug, or a single
pole cut-off device with a contact ope-
ning by at least 3,5mm.
The mains plug must be accessible af-
ter installation.
Electrical connections
The protective conductor (green/yellow) is connected to the earth
connection on the hob and therefore must also be connected to an external
earth connection .
Use a 10 A fuse.
If the power supply cable is damaged, it must be replaced with a cable or a spe-
cial unit available from the manufacturer or his After Sales Service.
Mixed and all-gas hobs
99633581_ML_C.qxd 14/12/04 15:37 Page 9
10
Connecting the gas supply
Natural gas
Meter
Gas
If the hob is installed above an oven or if
the proximity of other heat generating ele-
ments threatens to cause the connection
to heat up, it is vital that the connection be
made using a rigid pipe. If a hose or soft
pipe (case of butane gas) is used, it must
not come into contact with any of the
unit's moving parts or enter an area that is
likely to be obstructed.
Preliminary remarks
fig.A fig.B
Possible connections
The gas supply must be connected in line
with current regulations in the country of
installation.
FIXED NATURAL GAS SUPPLY.
For the user's safety, you must only cho-
ose one of the 3 following connections:
- Connection with a rigid pipe made
from copper and with screw on mechanical
connectors (G1/2 gas standard mark).
Make the connection directly at the end of
the elbow fitted on the appliance.
- Connection with a wavy metal (stain-
less steel) hose with screw on mechani-
cal connectors whose lifetime is unlimi-
ted (fig. A).
- Connection with a reinforced rubber
hose with screw on mechanical
connectors whose lifetime is 10 years
(fig. B).
Wavy metal hose with
mechanical connectors
Connection through
hose with
mechanical
connectors
When connecting your hob's gas supply, if you have to change the direction
of the elbow fitted on the appliance:
Change the gasket.
Screw on the elbow's nut while not exceeding a torque of 17 N.m.
Installing your hob in all simplicity
99633581_ML_C.qxd 14/12/04 15:37 Page 10
11
Connecting the gas supply (continued)
Possible connections
GAS SUPPLY FROM A CYLINDER
OR TANK (BUTANE/PROPANE
GAS).
For the user's safety, you must only
choose one of the following 3 connec-
tions:
- Connection with a rigid pipe made
from copper with screw on mechanical
connectors (G1/2 gas standard mark).
Make the connection directly at the end
of the elbow fitted on the appliance.
- Connection with a wavy metal
(stainless steel) hose with screw on
mechanical connectors whose lifetime
is unlimited (fig. A).
- Connection with a reinforced rub-
ber hose with screw on mechanical
connectors whose lifetime is 10 years
(fig. B).
In an existing system, a soft pipe fitted
with clamps whose lifetime is 5 years
may be used. It is necessary in this
case to use a adaptor without forgetting
to fit a sealing washer between the
adaptor and the hob's elbow (fig. C).
Screw on the adaptor with a torque not
exceeding 25 N.m.
The adaptor and sealing washer are
available from your After Sales Service
team.
BUTANE/PROPANE
Compulsory pressure regulator
propane
butanene butanene
All soft pipes and hoses whose lifetime is limited must have a maximum length of 2
metres and be accessible along their entire length. They must be replaced before the
end of their lifetime (marked on the pipe). Whatever the means of connection chosen,
check that the connection is leaktight, after installation, with soapy water.
Sealing washer
(not included)
Adaptor
(not included)
Clamp
(not included)
fig. A
Wavy metal hose
with mechanical
connectors
Hose
connection
Connection
through hose
with mechanical
connectors
fig. B
fig. C
Installing your hob in all simplicity
99633581_ML_C.qxd 14/12/04 15:37 Page 11
12
Installing your hob in all simplicity
Changing the type of gas supply
When carrying out this operation, you
should successively:
Adapt the gas connection
Change the injectors
Adjust the retarder on the taps
A
DAPT THE HOB CONNECTION
to the new
gas adjustment. Refer to the paragraph
“Gas connections”.
CHANGE THE INJECTORS in the following
way:
Remove the supports, and all the bur-
ner caps and heads.
Using the spanner supplied, unscrew
the injectors at the bottom of each dish
and remove them (fig 1).
- Replace these with the injectors
supplied in the wallet, in accordan-
ce with the gas rating table at the
end of the chapter; to do this:
Screw in the injectors by hand un-
til they are tight.
Put the spanner well onto the in-
jector.
With a pencil draw a line on the
hearth plate as indicated (fig. 2).
Turn the spanner clockwise until
the line appears on the other side
(fig. 3). Warning! Do not go
beyond this limit as you are
liable to cause damage.
Put the burner heads, covers and
pan supports back in position.
Cover
Head
Dish
Injector
Grill
Upper side of the hob
Spanner
Line
Fig. 3
Fig. 1
Fig. 2
Preliminary remarks
Your hob is delivered regulated for
natural gas.
The injectors needed for adaptation to
butane/propane can be found in the
plastic bag containing the instructions.
Please see the corresponding paragraph
on "Gas Connections".
Every time you change your gas supply,
mark the square on the label in the wallet
that corresponds to the new type of gas
(See "Gas Rating" in this chapter).
99633581_ML_C.qxd 14/12/04 15:37 Page 12
13
Installing your hob in all simplicity
Changing the type of gas supply (cont'd)
Knob
Gas tap
Sealing ring
ADJUST THE RETARDER ON THE TAPS
located under the knobs. Proceed as
follows:
Work on one tap at a time.
Pull off all knobs and sealing rings.
CHANGING FROM NATURAL GAS TO
THE BUTANE/PROPANE GAS
Using a small screwdriver, screw in
the brass retarder adjustment screw
(yellow) (Fig. 4) fully, clockwise.
- Check the position of the sealing rings
and knobs before putting them back in
place. Make sure the knobs are pushed
down as far as possible.
CHANGING FROM BUTANE / PROPANE
GAS TO NATURAL GAS OR TO BUTANE
/ PROPANE AIR
- Using a small screwdriver, unscrew the
brass retarder adjustment screw (yellow)
( Fig. 4) by two anticlockwise rotations.
- Push the control knob back in position,
light the burner and turn to maximum po-
wer. Then turn the knob back to its low fla-
me position.
- Remove the knob again then turn the ad-
justment screw clockwise as low as pos-
sible without extinguishing the flames.
- Put back the sealing ring and control knob
then turn it several times from maximum
position to minimum position : the flame
must not be extinguished. Otherwise,
re-adjust it by slightly screwing or unscre-
wing the adjustment screw so that a stable
flame is obtained when the knob is turned
from maximum to minimum position.
- Put the burner heads, covers and pan
supports back in position.
Adjustment
screw
Fig. 4
Tap axis
Model without safety device
Tap axis
Fig. 4
Adjustment screw
Model with safety device
99633581_ML_C.qxd 14/12/04 15:37 Page 13
14
Installing your hob in all simplicity
Changing the type of gas supply (cont'd)
Gas rating
Appliance designed for installation: LPG
SINGAPOUR -
CHINA - BEIJING - SHANGAI
Hourly input -see below: 28-30mbar
D
OUBLE
-CROWN BURNER FRONT LEFT
Indicator marked on injector 92
Nominal heat rating (kW) 3,50
FAST BURNER BACK RIGHT
Indicator marked on injector 78
Nominal heat rating (kW) 2,35
EXTRA FAST BURNER FRONT LEFT
Indicator marked on injector 88
Nominal heat rating (kW) 3,10
SEMI
-FAST BURNER BACK LEFT
Indicator marked on injector 62
Nominal heat rating (kW) 1,45
A
UXILIARY BURNER FRONT RIGHT
Indicator marked on injector 45
Nominal heat rating (kW) 0,750
4 DOUBLE-CROWN RING GAS HOB
Total nominal heat rating (kW) 8,05
60 CM HOB 4 GAS RINGS WITH LARGE HIGH-SPEED RING
Total nominal heat rating (kW) 7,65
60 CM HOB 3+1 1500 W ELECTRIC HOTPLATE
Total nominal heat rating (kW) 6,20
FR - GR - GB - PT FR FR
Appliance designed for installation: Butane Propane Natural Natural Air-
FR ....................................Cat : III1C2E+3+ gas gas propane
GB - GR - PT ....................Cat : II2H3+ Air-
G30 G31 G20 G25 butane
G130
Hourly input -see below at 15°C at 1013 mbar 28-30mbar 37 mbar 20 mbar 25 mbar 8 mbar
D
OUBLE -CROWN BURNER FRONT LEFT
Indicator marked on injector 92 92 144 144 360
Nominal heat rating (kW) 3,50 3,50 3,80 3,80 3,60
Low heat rating (with/without security device) (kW) 1,450 1,550 1,300
Hourly output (g/h) 254 250
Hourly output (l/h) 362 421 503
F
AST BURNER BACK RIGHT
Indicator marked on injector 78 78 121 121 210
Nominal heat rating (kW) 2,35 2,35 2,35 2,35 2,40
Low heat rating (with/without security device) (kW) 0,830 0,870 0,650
Hourly output (g/h) 171 168
Hourly output (l/h) 224 260 336
E
XTRA FAST BURNER FRONT LEFT
Indicator marked on injector 88 88 137 137 298
Nominal heat rating (kW) 3,10 3,10 3,20 3,20 3,10
Low heat rating (with/without security device) (kW) 0,830 0,870 0,780
Hourly output (g/h) 225 221
Hourly output (l/h) 305 354 434
S
EMI-FAST BURNER BACK LEFT
Indicator marked on injector 62 62 94 94 165
Nominal heat rating (kW) 1,45 1,45 1,50 1,50 1,50
Low heat rating (with/without security device) (kW) 0,620 0,615 0,550
Hourly output (g/h) 105 104
Hourly output (l/h) 143 166 210
A
UXILIARY BURNER FRONT RIGHT
Indicator marked on injector 45 45 63 63 C12
Nominal heat rating (kW) 0,750 0,750 0,850 0,850 1,00
Low heat rating (with/without security device) (kW) 0,300 0,350 0,350
Hourly output (g/h) 55 54
Hourly output (l/h) 81 94 140
4
DOUBLE -CROWN RING GAS HOB
Total nominal heat rating (kW) 8,05 8,05 8,50 8,50 8,5
Maximum output (g/h) 585 576
(l/h) 810 941 1189
60
CM HOB 4 GAS RINGS WITH LARGE HIGH-SPEED RING
Total nominal heat rating (kW) 7,65 7,65 7,90 7,90 8,00
Maximum output (g/h) 556 547
(l/h) 753 874 1120
60
CM HOB 3+1 1500 W ELECTRIC HOTPLATE
Total nominal heat ratingl (kW) 6,20 6,20 6,40 6,40 6,5
Maximum output (g/h) 451 443
(l/h) 610 708 910
99633581_ML_C.qxd 14/12/04 15:37 Page 14
15
Installing your hob in all simplicity
Changing the type of gas supply (cont'd)
Gas rating (cont’d)
This table shows the position of the injectors on your hob depending on the type of gas you use.
The number is marked on each injector.
MARK ON THE INJECTORS
Natural gas
94 121
137 63
62 78
88 45
60 cm model 4 gas rings
with extra-fast
60 cm model 4 gas ring
with 1 double crown
Butane/Propane
gas
165 210
298 C12
Air-Propane/
Air-Butane
62 78
88 45
60 cm model 4 gas rings
with extra-fast
LPG
62 78
92 45
LPG
62 78
92 45
Butane/Propane
gas
Natural gas
94 121
144 63
60 cm model 4 gas rings
with double crown
Natural gas
Elec 121
137 63
Elec
78
88 45
60 cm model 3 gas ring
with 1 double crown
Butane/Propane
gas
165 210
360 C12
Air-Propane/
Air-Butane
Elec 210
298 C12
Air-Propane/
Air-Butane
60 cm model 3 gas rings
with double crown
Elec 78
92 45
LPG
99633581_ML_C.qxd 14/12/04 15:37 Page 15
16
Lighting a hob fitted WITH A SAFETY
DEVICE (depending on model)
Each burner has its own gas tap which
is opened by pressing down on the
control knob and then turning it anti-
clockwise.
The gas tap is closed when the control
knob is in position
”.
Choose the gas burner you need using
the symbols at the side of each control
knob; (E.g. back right-hand burner ).
Your hob is equipped with an
automatic lighting system integrated into
each control knob.
To ignite a burner, press down and
turn the knob anti-clockwise until it
is pointing to the maximum
position .
Keep the knob pressed down. This will
trigger off a series of sparks that will light
up the burner.
Adjust the flame to the height your
require by turning the control knob
between the and symbols.
The safety system for the burners is a metal
rod next to the flame.
Using your hob in all simplicity
Choose the gas burner you need using
the symbols at the side of each control
knob;
(E.g. back right-hand burner ).
Each burner is controlled by a tap
fitted with a safety system, which cuts the
gas off automatically if ever the flame goes out
by accident (overflowing, drafts, etc.).
Your hob is equipped with an
automatic lighting system integrated into
each control knob.
To ignite a burner, press down and
turn the knob anti-clockwise juntil it
is pointing to the maximum
position .
Adjust the flame to the height your
require by turning the control knob between
the and symbols.
How to use your gas burners?
- If ever your flame goes out, relight it as per normal procedure.
- The flames on the burner are smaller near the grate supports to avoid any damage being
done to the enamel.
- The noise made by certain burners is related to their power and burning gas; this does not
harm the quality of cooking in any way.
Sparker
Gas safety
device
(depending
on model)
Lighting a hob NOT FITTED WITH A
SAFETY DEVICE (depending on model)
To set off the safety system, keep the knob
pressed completely down for a few seconds
after the flame has lit up.
99633581_ML_C.qxd 14/12/04 15:37 Page 16
17
Using your hob in all simplicity
Which pans are best adapted for use on the gas burner ?
Recommended pan sizes:
Adjust the flames so that they do not
lick up the side of your pan.
Do not use a pan with a convex
or concave bottom.
Do not leave the gas on benea-
th an empty pan.
Do not use pans whose bases or
handles may partially cover
control knobs.
Some hobs are equipped with a specific
"WOK" type support stand, to be used
only on the central "Double Crown" ring.
This "WOK" type stand allows you to use
receptacles with a concave base. Used
with the "Double Crown" ring, it allows
better heat distribution around large
receptacles such as woks and large
diameter paella pans.
RIGHT
WRONG
CONVEX
CONCAVE
Keep all natural air-vents open or have a mechanical ventilation system installed (a
mechanically ventilated hood).
- Prolonged, intensive use of the hob may require extra ventilation; by opening a window
for example or producing more efficient ventilation by increasing the power of the existing
mechanical ventilation (a minimum air input of 2m3/hour per kW of gas energy is required.)
E.g. : for a 60 cm hob with 4 gas-rings
Total power: 0,85 + 1,5 + 2,35 + 3,2 = 7,9 kW.
7,9 kW x 2 = 15,8 m
3
/h per hour minimum flow-rate.
Extra burner
double-crown
20 to 30 cm
Extra burner
Extra-fast
18 to 28 cm
Medium burner
fast
16 to 26 cm
semi-fast
14 to 22 cm
auxiliary
12 to 16 cm
Small burner
Wok stand
99633581_ML_C.qxd 14/12/04 15:37 Page 17
18
Using your hob in all simplicity
How to use the electric hotplate?
To heat it up
Turn the knob to the point that corres-
ponds to the cooking you want to do
(See cooking table at the end of the
instruction booklet). The electric
hotplate 'on' light comes on.
The first time you use the electric hot-
plate, leave it on for 3 minutes at
maximum temperature without using
a pan to harden the surface coating.
Which pans are best adapted for use
on the electric hotplate?
Which pans are to be used on the
electric hotplate?
Use pans with flat bottoms that are in
complete contact with the electric hot-
plate surface:
- Stainless steel with a thick trimetal or
"sandwich" base,
- Aluminium with a thick (smooth) ba-
se,
- Enamelled steel.
Always use a pan of suitable
size: the diameter of the pan
must be larger than the diameter
of the electric hotplate.
YES
NO
Finish off your cooking with the knob
turned to (o). This lets you take ad-
vantage of the heat that has accumu-
lated in the electric hotplate.
Whenever possible use a cover on
your pans to avoid losing any heat by
evaporation.
- Never leave a electric hotplate turned on without a pan or with an empty pan.
- The electric hotplate stays hot for a certain time after it has been switched off in
the “O” position.
E.g., position 3
99633581_ML_C.qxd 14/12/04 15:37 Page 18
19
Looking after
sparkers and
injectors
Looking after
the electric
hotplate
- If ever the sparkers
get dirty, clean them
with a stiff non-
metallic brush.
- The gas injectors are
in the centre of each
burner in the form of
a "pot". Make sure not
to block them up
partially when
cleaning the hob, as this will considerably
reduce the performance of your gas-rings.
- Small hard-bristled
brush.
- Safety pin
- The electric hotplate is protected by a black
surface coating. Therefore, avoid using any
abrasive products. After use, wipe it clean
with an oily cloth.
- If ever a electric hotplate starts to rust,
remove the rust with (with emery paper or
similar) and re-coat the electric hotplate with
a high-temperature renovating product to be
found at your local distributor.
- Renovating product
available in the shops.
Looking after
the grills and
burners
- Use a non-abrasive cream for removing any
persistent stains. Then rinse with clean
water. Dry each burner element carefully
before re-lighting your hob.
- Non-abrasive cream.
- Household sponge.
Looking after
enamel or
stainless steel.
- Use polishing cream for cleaning the enamel
on the hob. Polish with a dry clean cloth.
- Never allow any acid liquids such as lemon
juice, vinegar, etc. to remain in contact with the
enamel.
- Use a sponge and soapy water or a standard
stainless steel cleaner for cleaning the stainless
steel parts on your hob.
- Soft polishing
cream.
- Standard stainless
steel cleaning
product
HOW TO PROCEED
ACCESSORIES TO
BE USED
Keeping your hob in good condition is easy if you clean it before it is completely
cold. Even so, never clean it when it is in use. Put all the electric and gas control
knobs at zero.
How to look after your hob?
- It is better to clean the elements of your hob by hand, do not put any parts
in the dishwasher.
- Never use scouring pads for cleaning your hob.
- Do not use a steam cleaner.
thermocouple
Nut
Injector
Sparker
99633581_ML_C.qxd 14/12/04 15:37 Page 19
20
You have doubts about whether your hob is working correctly .... ...... this does not
necessarily mean there is a breakdown. Nevertheless, check the following points
If your table is fitted with a gas
safety system and the flames go out
as soon as you release the control
knob.
In the low position the flames go
out or are too high.
Flames are irregular.
- Avoid any severe drafts in the room.
- Check that the gas you are using corresponds to the injectors that
have been installed (See injector identification in the "Gas Rating"
chapter).
Remember that gas hobs are delivered preset for use with natural gas.
Check the adjustment of the low power screw (See paragraph
"Changing the type of gas supply").
- Check that the burners and injectors are clean and assembled
correctly.
- Check you have enough gas in your gas cylinders.
The knobs get hot during cooking.
Use small pans on the burners next to the control knobs. Large pans
are to be put on the large burners furthest away from the knobs.
Put the pan in place with the burner in the middle. The pan should not
be above the control knobs.
WHAT SHOULD YOU DO?IF YOU REALIZE THAT
Lighting the burners:
There is no sparking when the
control knobs or buttons are pressed
down.
When you only press down one
control knob all the burners spark.
Sparking takes place but the burners
do not light up.
- Check the electrical connections on the hob.
- Check that the sparkers are clean.
- Check that the burners are clean and in position.
- If the hob is fixed to the worktop, make sure that the fixing clamps
have not been twisted.
- Check that the sealing rings have not come out of place.
This is normal. The lighter system is centralised, and all the burners
spark at the same time.
- Check that the gas inlet pipe has not been squashed.
- Check that the gas inlet pipe tube is less than 2m long.
- Check that the main gas tap is open.
- If you use gas tanks or cylinders check that they are not empty.
- If you have just installed your hob or changed a gas cylinder, keep
the control knob wide open for a few seconds so that the gas can get
through.
- Make sure the injector is not blocked up. if this is the case, clear it
with a safety pin.
- Light up your gas-ring before putting a pan on it.
- Push the control knob down completely and keep it under pressure
for a few seconds after the burner has lit.
- Check that the burner parts are in place.
- Check that the sealing rings under the control knobs have not come
out of place.
- Avoid any severe drafts in the room.
- Light the burner before putting your pan on it.
Minor troubleshooting
99633581_ML_C.qxd 14/12/04 15:37 Page 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Brandt TE516XS1 Le manuel du propriétaire

Taper
Le manuel du propriétaire