SportsArt A978 Le manuel du propriétaire

A978 OWNER’S MANUAL CONTENTS

1. INTRODUCTION ................................................................................ 2

2. SAFETY PRECAUTIONS .................................................................. 3

3. LIST OF PARTS ................................................................................. 4

4. ASSEMBLE THE PRODUCT ............................................................. 7

STEP 1 Install the Lower Connector and Seat Frame ........................... 7

STEP 2 Install the Install the Left/Right Frame ...................................... 8

STEP 3 Install the Install the Upper Connector ..................................... 9

STEP 4 Install the Left/Right Handles ................................................... 10

STEP 5 Install the Seat Cushion ........................................................... 11

STEP 6 Install the Back Cushion .......................................................... 12

STEP 7 Install the Weight Plate Pegs ................................................... 13

STEP 8 Level and Secure the Unit ....................................................... 14

STEP 9 Unit Inspection ......................................................................... 16

5. OPERATE THE PRODUCT ............................................................... 17

OPERATION Safety Operating Area ..................................................... 17

OPERATION Operate the Product ........................................................ 18

6. MAINTENANCE ................................................................................ 19

MAINTENANCE Safety Precautions .................................................... 19

MAINTENANCE Schedule .................................................................... 20

MAINTENANCE Task List .................................................................... 21

MAINTENANCE One-Year Maintenance Log ....................................... 22

7. CONSIGNES DE SÉCURITÉ IMPORTANTES ................................. 23

8. APPENDIXES ................................................................................... 25

APPENDIXES Exploded Diagram ........................................................ 25

*We reserve the right to revise this manual at any time without notice.

2

1. INTRODUCTION

Congratulations on the purchase of a high quality SportsArt product, the

A978 Wide Chest Press machine. Constructed of high quality materials and

designed for years of reliable performance, this product was made for full

commercial use.

Before this product is assembled or operated, we recommend that you

familiarize yourself with this manual. Understanding the correct assembly

and operation of this product will help ensure that exercisers obtain their

tness goals safely and successfully.

RL

3

2. SAFETY PRECAUTIONS

This product was designed and built for optimum safety. However certain precau-

tions apply during the use of this product. Please note the following safety

precautions:

• Please read the entire manual before assembly and operation. Make sure the

product is installed and operated as instructed in this manual.

• Assemble and operate the product on a solid, level surface. Do not use outdoors

or near water, including pools and saunas.

• Check the product before every use. Make sure all parts are assembled, and all

fasteners are tightened. Do not use the product if it is disassembled in any way.

• Wear proper workout clothing. Do not wear loose clothing. Do not wear shoes

with leather soles or high heels. Tie all long hair back. Do not go barefoot on this

product.

• Keep away from moving parts. Moving parts may or may not stop immediately if

an object becomes caught or impedes normal motion.

• Use this product only for its intended purpose as described in this manual.

• Be careful when mounting and dismounting the unit.

• Never operate this product if it has been damaged in any way. If it is not work-

ing properly, or has been dropped or damaged, contact a service technician for

repairs.

• Do not use accessories or parts that are not specifically recommended by the

manufacturer (SportsArt) . Such parts might cause injuries or cause the unit to

fail and void the warranty. We will not be responsible for any safety issue that

arises due to the misuse of accessories or parts. At the same time, we will termi-

nate the warranty terms of this equipment.

• This product is not intended for use by persons (including children 12 or younger)

with reduced physical, sensory, or mental capabilities, or by people who are

otherwise deficient in product knowledge or experience. If such people use this

product, they should be given training and be supervised at all times by some-

one responsible for their safety.

• Contact your SportsArt representatives on all materials damaged in shipment.

(Note: Shipping damages are the responsibility of the carrier.)

• Unpack and verify contents of boxes according to the list of parts to check if any

parts are missing.

• Children 12 or younger should be supervised to ensure that they do not play on

or near the product.

• The user weight limit for this product is 227 kg, 500 lb.

• Maintenance and repair must be performed by trained service personnel

only. Improper maintenance would not only damage the machine, but

also may present a danger to the exerciser.

• Warning that any of the adjustment devices that could interfere with the

user’s movement should not be left projecting.

• Over exercise may result in serious injury or death.

CAUTION: If you feel any pain or any abnormal sensations, STOP YOUR WORK-

OUT and consult your physician immediately. Work within your recommended ex-

ercise level. DO NOT work to exhaustion. Before beginning any exercise program,

you should consult with your doctor. It is recommended that you undergo a complete

physical examination.

4

3. LIST OF PARTS

Assembly Parts

No. Name Qty. No. Name Qty.

A1 Lower connector 1 A7a Left selector plate 1

A2 Right frame 1 A8 Back cushion 1

A3 Left frame 1 A9 Seat cushion 1

A4 Seat frame 1 A10 Weight plate peg 6

A5 Upper connector 1 A11 Curved connecting plate 4

A6 Right handle 1 A12 Set spring 2

A6a Right selector plate 1 A13 Owner’s manual 1

A7 Left handle 1 A14 Hardware kit 1

5

Components on the Product

No. Name Specication Notes

51

Hex head screw M10*P1.5*L75

Spring washer M10

Washer D16*d10.2*t1.0

Bushing ØD16*t2.0*L45.5

Inner hex screw M4*P0.7*L4

Washer D16*d10.2*t1.0

Nylon hex lock nut M10

52

Flat Washer D22*d8.2*t2

Spring washer M8

Mushroom top inner hex screw M8*P1.25*L25

53 Beveled head inner hex screw M8*P1.25*L20

Nylon hex lock nut M8

54 Mushroom top inner hex screw M8*P1.25*L25

Flat Washer D22*d8.2*t2

55 Mushroom top inner hex screw M6*P1.0*L15

Handle washer D20*d7*t2.0

56 Inner hex screw M6*P1.0*L10

Spring washer M6

57

Axle ØD25*L104

Bushing

Flat washer D26*d8.3*t3

Spring washer M8

Inner hex screw M10*P1.5*L25

60 End cap

Components in the Hardware Kit

No. Name Qty. Specication Notes

Double open-end wrench 2 13mm*17mm

L-shaped Allen wrench 1 M5

L-shaped Allen wrench 2 M6

L-shaped Allen wrench 1 M4

L-shaped Allen wrench 2 M8

Open-end wrench 1 35mm

31

Hex head screw 2 M10*P1.5*L30

Spring washer 2 M10

Washer 2 D21*d10.5*t1.5

6

Components in the Hardware Kit

No. Name Qty. Specication Notes

32

Nylon hex lock nut 2 M10

Washer 4 D21*d10.5*t1.5

Spring washer 2 M10

Hex head screw 2 M10*P1.5*L30

33 Floor xing bracket 1

7

4. ASSEMBLE THE PRODUCT

Follow instructions below to assemble this product. Note that in this manual

the words “left” and “right” are used to refer to the product and its parts. As

such, these designations correspond to the “left” and “right” sides of a person

in position to exercise on this product. Also, for brevity, the word “screws” is

used where screws, washers, and other hardware may be involved.

STEP 1 Install the Lower Connector and Seat Frame

Follow instruction below to install the lower connector and the seat frame.

Attach the seat frame (A4) to the lower connector (A1), and then secure the

assembly with screws (31).

8

STEP 2 Install the Left/Right Frame

Follow instructions below to install the left/right frame.

First, remove nuts (51) from the curved connecting plate (A11) and align the

left/right frame (A2) (A3) to the holes in the lower connector (A1), then loose-

ly secure the assembly with the curved connecting plate (A11) and nuts (51)

as shown. Do not tighten nuts.

(Note: The left/right frame (A2) (A3) are marked “L” for left or “R” for right.

Make sure they are installed properly.)

R

L

9

STEP 3 Install the Upper Connector

Follow instructions below to install the upper connector.

First, remove nuts (51) from the curved connecting plate (A11) and align the

left/right frame (A2) (A3) to the holes in the upper connector (A5), then loose-

ly secure the assembly with the curved connecting plate (A11) and nuts (51)

as shown. Do not tighten nuts. And then secure the upper connector (A5) to

the seat frame (A4) with screws (32) as shown.

10

STEP 4 Install the Left/Right Handles

Follow instructions (a) through (b) below to install the left/right handles.

(a) First remove screws (57) from the left/right handles (A7) (A6).

(b) Align the right handle (A6) to the holes in the right frame (A2), and then

secure the assembly with screws (57) as shown.

(Note: Follow the same instructions to install the left handle (A7).)

(c) Remove the end cap (60) from the right selector plate (A6a) and align the

right selector plate (A6a) to the hole in the right handle (A6) and then

secure the assembly with the end cap (60) as shown.

(Note: Follow the same instructions to install the left selector plate (A7a).)

(a)

(b)

(c)

11

(a) (b)

(c)

(d)

STEP 5 Install the Seat Cushion

Follow instructions (a) through (d) below to install the seat cushion.

(a) First, remove screws (52) from the seat cushion (A9).

(b) Remove screws (53) from the lower connector (A1).

(c) Attach the seat cushion plate from the seat cushion (A9) onto the lower

connector (A1), and then secure the assembly with screws (53).

(d) Finally, attach the seat cushion (A9) onto the seat cushion plate, and

secure the assembly with screws (52).

12

STEP 6 Install the Back Cushion

Follow instruction below to install the back cushion.

First, remove screws (54) from the back cushion (A8) and align the back

cushion (A8) to the holes in the seat frame (A4), then secure the assembly

with screws (54) as shown.

13

STEP 7 Install the Weight Plate Pegs

Follow instructions (a) through (c) below to install the weight plate pegs.

(a) First, remove screws (55) from the weight plate pegs (A10).

(b) Loosen screws (56) from the front of the left/right handles (A6) (A7) and

then install the weight plate pegs (A10) onto the left/right handles (A6)

(A7) and secure them with screws (55).

(c) Finally, tighten all screws.

(a)

(b)

(c)

14

STEP 8 Level and Secure the Unit

Follow instructions (a) through (d) below to level and secure the unit.

(a) Rotate the set screw to allow adjustment of the leveler foot.

(b) Rotate the leveler foot downward against the floor.

(c) Rotate the set screw upward against the frame to secure this position.

(d) Secure the floor fixing bracket (33) to the floor with the floor fixing

bolt, nut and washer as shown to make sure the machine is firmly fixed

to the floor when operating. (Level the machine before securing the floor

fixing bolt.)

(Note: The screw hole of floor fixing bracket is Ø9mm, please make

sure using the suitable floor fixing bolt and drilling the proper hole on

the floor.)

abcd

15

STEP 8 Level and Secure the Unit (Continued)

If the product is installed on an uneven surface to cause the instability of the

product, place the support spacer under the foot pad to make sure its stabil-

ity. (A few support spacers are provided in the packaging of this product.)

16

STEP 9 Unit Inspection

After completing the assembly or regular maintenance, please follow instruc-

tions (a) through (c) below to inspect the unit. If the unit is disassembled or

has been damaged in any way, it might cause injuries or cause the unit to

fail.

(a) Make sure the unit is steady and on a level surface. If the unit is not

steady, make adjustments according to the instructions “Level the Unit”

of this manual.

(b) Make sure all parts are assembled and all fasteners are tightened.

(c) Please follow operating instructions to test operation and conrm that

the equipment is working properly. (Please refer to “Operate the Product”

of this manual.)

17

5. OPERATE THE PRODUCT

OPERATION Safety Operating Area

(a) Make sure operate the unit in safety area as shown. Do not allow people

to be near this area when operating.

(b) Noise emission under load is higher than without load.

(c) Over exercising or improper workout position may result in serious injury.

(d) This product is intended for exercise arms.

18

OPERATION Operate the Product

(a) Select the appropriate weight plates placed on both sides of the weight

plate pegs, and then secure the weight plates with set springs.

(b) Adjust the seat cushion and the handles to the most comfortable position.

(*Pull out the knob on the right/left selector plate (A6a) (A7a). You can

rotate and secure the handles for use within a 360-degree range.)

(c) Inhale while pulling the handles to your waist, exhale slowly back to the

original position.

* Note: While operating the machine, if the weight plate is moving around.

Please stop immediately, re-position the weight plate before continuing.

* Weight limit: Weight plate limit of 250Kg (Unilateral 125Kg)

* Please exercise within the range of your skill and training.

* Operate this machine must be supervised under coaches instructions in

order for safety.

(c)

(b)

(a)

(b)

19

6. MAINTENANCE

This section covers maintenance topics and includes a maintenance

schedule, task list, and log.

MAINTENANCE Safety Precautions

●Please follow standard safety precautions when servicing this product.

●Do NOT use a water damp towel to clean the product and do perform the

following maintenances.

●Do NOT use cleaners with alcohol, ammonia, or other damaging chemi-

cals. The use of such chemicals can damage the product and void the war-

ranty. Never spray or pour any liquid directly onto the product. Doing so can

damage components and void the warranty.

●Use a clean, lint-free towel, dampened with a mixture of Simple Green®

all-purpose cleaner, to thoroughly clean the handlebar and the console.

●This product has moving parts that can be hazardous. Exercise caution

when maintaining, operating, or moving this product.

● Do not use accessories or parts that are not specically recommended

by the manufacturer (SportsArt) . Such parts might cause injuries or cause

the unit to fail and void the warranty. We are not responsible for any safety

issue that arises due to the misuse of accessories or parts. At the same

time, we will terminate the warranty terms of this equipment.

●Maintenance and repair must be performed by trained service personnel

only. Improper maintenance would not only damage the machine, but may

also present a danger to the exerciser.

●Keep this product out of use until maintenance is completed.

20

MAINTENANCE Schedule

Area Day Week Month Quarter Year Notes

1 Exterior Clean.

2 Screws Inspect for looseness and

secure if necessary.

3 Cushions Wipe with a damp cloth.

4Extension

tube Clean and lubricate.

La page est en cours de chargement...

SportsArt A978 Le manuel du propriétaire

SportsArt A978 Le manuel du propriétaire

dans d''autres langues