Simplicity BRUTE DUAL STAGE SNOWTHROWER DOM, LF 16.5TP 33 INCH (83,8 CM) Manuel utilisateur

Marque: Simplicity

Modèle: BRUTE DUAL STAGE SNOWTHROWER DOM, LF 16.5TP 33 INCH (83,8 CM)

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

1751326

Revision A

Walkbehind Snowthrower

Mfg. No. Description

1695874 Dual Stage Snowthrower, 16.5 TP, 33 Inch (83,8 cm)

en Operator’s Manual

fr Manual de l’opérateur

Not for

Reproduction

2www.brutepower.com

Not for

Reproduction

The Illustrated Parts List for this machine can be downloaded from www.brutepower.com. Please provide model and serial num-

ber when ordering replacement parts.

BRUTE is a trademark of Briggs & Stratton Power Products Group, LLC

Milwaukee, WI USA

TABLE OF CONTENTS

General Information

Thank you for purchasing this quality-built BRUTE snowthrower. We’re pleased that you’ve placed your confidence in the BRUTE

brand. When operated and maintained according to the instructions in this manual, your BRUTE product will provide many years of

dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with snowthrowers and how to

avoid them. This snowthrower is designed and intended only for snow throwing and is not intended for any other purpose. It is im-

portant that you read and understand these instructions throroughly before attempting to start or operate this equipment. Save

these instructions for future reference.

Front Cover..................................................................................................................1

Contents ......................................................................................................................3

Operator Safety...........................................................................................................4

Assembly...................................................................................................................10

Features and Controls .............................................................................................13

Operation...................................................................................................................15

Maintenance..............................................................................................................23

Troubleshooting........................................................................................................28

Warranties .................................................................................................................30

Specifications ...........................................................................................................32

Product Reference Data

When contacting your authorized dealer for replacment parts, service, or information you MUST have these numbers.

Snowthrower

Model Number _________________________

Revision __________

Serial Number ______________________________

Engine

Model Number _________________________

Revision __________

Serial Number ______________________________

Date Purchased ____________________

Not for

Reproduction

OPERATOR SAFETY

Hazard Symbols and Meanings

Rotating

Impeller

NOTE: Not all control symbols shown on this page will

appear on your snowthrower. See Features and Controls

section for the applicable symbols.

Rotating

Auger

Rotating

Parts

Fire

Shock

Hot

Surface

Safe

Distance

Rotating

Gears

Thrown

Objects

Explosion

Tox i c

Fumes

Ear

Protection

Eye

Protection

Moving

Parts

Kickback

Hazardous

Chemical

Control Symbols on Equipment

Oil

Fuel

Shutoff

Choke

Off

Choke

Stop

Slow

Fast

Auger

Clutch

Electric

Start

Engine

On-Off

Choke-

Run

Traction

Control

Auger

Control

Discharge

Chute

Deflector

Heated

Hand

Grips

Forward

Neutral

Reverse

Engine

Primer

STOP

Engine

Run

Engine

Stop

Wheel

Lock

Free-Hand™ Control

Easy-Turn™

Traction Control

4www.brutepower.com

Not for

Reproduction

OPERATOR SAFETY

The safety alert symbol and signal word (DANGER,

WARNING, CAUTION, or NOTICE) is used to indicate the likelihood

and potential severity of personal injury and/or damage to the

product. In addition, a hazard symbol may be used to represent the

type of hazard.

Safety Alert Symbol and Signal Words

DANGER indicates a hazard which, if not avoided, will result

in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE indicates a situation that could result in damage

to the product.

DANGER

• Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

• This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so will result in

death or serious injury.

WARNING

Certain components in this product and its related accessories

contain chemicals known to the state of California to cause

cancer, birth defects, or other reproductive harm. Wash hands

after handling.

WARNING

The engine exhaust from this product contains chemicals

known to the State of California to cause cancer, birth defects,

or other reproductive harm.

• Be thoroughly familiar with the controls and the proper use of the

snow thrower.

• Make sure you are properly trained before operating the

snowthrower.

• Know how to stop the unit and disengage the controls quickly.

• Never allow anyone to operate the snowthrower without proper

instruction.

• Always follow the instructions in the operator’s manual, if the

snowthrower will be stored for an extende d period.

• Maintain or replace safety and instruction labels as necessary.

• Never attempt to make major repairs on the snowthrower unless

you have been properly trained. Improper servicing of the

snowthrower can result in hazardous operation, equipment

damage, and voiding of the product warranty.

DANGER

Read, understand, and follow all the

instructions on the snowthrower and in the

operator’s manual before operating this unit.

Failure to observe the safet y instructions in

this manual will result in death or serious

injury.

Read the Manual

TO SAFELY CLEAR A CLOGGED DISCHARGE CHUTE

DANGER: Hand contact with the rotating impeller inside

the discharge chute is the most common cause of

injury associated with snow throwers. Never use your

hands to clean out the discharge chute.

FOLLOW THESE INSTRUCTIONS:

1. Shut OFF the engine.

2. Wait 10 seconds to be sure the impeller blades have stopped

rotating.

3. Always use a clean-out tool, not your hands.

DANGER

Discharge chute contains rotating impeller to

throw snow. Never clear or unclog the

discharge chute with your hands. Fingers can

quickly become caught in the impeller. Always

use a clean-out tool.

Failure to observe these safety instructions

will result in traumatic amputation or severe

laceration.

Discharge Chute

Not for

Reproduction

OPERATOR SAFETY

WHEN ADDING FUEL

• Turn off engine and let cool at least 3 minutes before removing

the fuel cap and adding fuel.

• Fill fuel tank outdoors or in a well ventilated area.

• Do not overfill the fuel tank. To allow for the expansion of gasoline,

do not fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• Check fuel lines, cap, and fittings frequently for cracks or leaks.

Replace if necessary.

• Use an approved fuel container.

• If fuel spills, wait until it evaporates before starting engine.

WHEN STARTING ENGINE

• Ensure that spark plug, muffler, fuel cap, and air cleaner (if

equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• If fuel is spilled, do not attempt to start the engine, but move the

snow thrower away from the area of the spill, and avoid creating

any source of ignition, until the fuel vapors have dissipated.

• Do not over-prime the engine. Follow the engine starting

instructions in this manual.

• If the engine floods, set choke (if equipped) to OPEN/RUN

position, move throttle (if equipped) to FAST position and crank

until engine starts.

WHEN OPERATING EQUIPMENT

• Do not tip the snowthrower at an angle which causes the fuel to

spill.

• Do not choke the carburetor to stop the engine.

• Never run the engine with the air cleaner assembly (if equipped)

or the air filter (if equipped) removed.

WHEN CHANGING OIL

• If you drain the oil from the top oil fill tube, the fuel tank must be

empty or fuel can leak out and result in a fire or explosion.

WHEN TRANSPORTING EQUIPMENT

• Transport with fuel tank EMPTY, or with fuel shut-off valve OFF.

WHEN STORING GASOLINE OR EQUIPMENT WITH FUEL

IN TANK

• Store away from furnaces, stoves, water heaters, or other

appliances that have pilot light or other ignition source because

they can ignite fuel vapors.

DANGER

Fuel and its vapors are extremely flammable

and explosive. Always handle fuel with extreme

care.

Failure to observe these safety instructions can

cause a fire or explosion which will result in

severe burns or death.

Fuel Handling

• Keep the area of operation clear of all persons, particularly small

children and pets.

• Thoroughly inspect the area where the snowthrower will be used

and remove all doormats, sleds, boards, wires, and other foreign

objects.

• Do not operate the snowthrower without wearing adequate winter

clothing.

• Wear footwear that will improve footing on slippery surfaces.

• Use caution to avoid slipping or falling especially when operating

the snowthrower in reverse.

• Never operate the snowthrower without good visibility or light.

Always be sure of your footing, and keep a firm hold on the

handles.

• Do not clear snow across the face of slopes. Use extreme caution

when changing direction on slopes. Do not attempt to clear steep

slopes.

• Do not overload the machine capacity by attempting to clear

snow too quickly.

• Never operate the snowthrower at high transport speeds on

slippery surfaces. Look behind the snowthrower and use care

when operating in reverse.

• Do not use the snowthrower on surfaces above ground level such

as roofs of residences, garages, porches, or other such structures

or buildings.

• Operators should evaluate their ability to operate the snowthrower

safely enough to protect themselves and others from injury.

• The snowthrower is intended to remove snow only. Do not use the

snow thrower for any other purpose.

• Do not carry passengers.

• After striking a foreign object, shut OFF the engine, disconnect

the cord on electric motors, thoroughly inspect the snowthrower

for any damage, and repair the damage before restarting and

operating the snowthrower.

• If the snowthrower vibrates abnormally, shut OFF the engine.

Vibration is generally a warning of trouble. See an authorized

dealer if necessary for repairs.

• For models equipped with electric starting motors, disconnect the

power cord after the engine starts.

DANGER

This snowthrower is only as safe as the

operator. If it is misused, or not properly

maintained, it can be dangerous. Remember

you are responsible for your safety and that of

those around you.

Operation and Equipment Safety

6www.brutepower.com

Not for

Reproduction

OPERATOR SAFETY

• Keep children out of the area during operation. Children are often

attracted to the equipment. Be mindful of all persons present.

• Be alert and turn unit off if children enter the area.

• Never allow children to operate the unit.

• Use extra care when approaching blind corners, shrubs, trees, or

other objects that may obscure vision. Children may be present.

DANGER

Tragic accidents can occur if the operator is

not alert to the presence of children. Children

are often attracted to the unit and the

operating activity. Never assume that children

will remain where you last saw them.

Children

• Start and run engine outdoors.

• Do not run the engine in an enclosed area, even if doors or

windows are open.

DANGER

Engines give off carbon monoxide, an odorless,

colorless, poison gas.

Breathing carbon monoxide can cause nausea,

fainting, or death.

Engine Safety

• Disengage all clutches and shift into neutral before starting the

engine.

• Let the engine adjust to outdoor temperatures before starting to

clear snow.

• Use a grounded three-wire plug-in for all snowthrowers equipped

with electric drive motors or electric starting motors.

DANGER

Safe operation of the snowthrower requires the

proper care and maintenance of the engine.

Failure to observe the safety instructions in this

manual will result in death or serious injury.

• Always wear safety glasses or eye shields during operation, and

while performing an adjustment or repair.

• Always be aware of the direction the snow is being thrown.

Nearby pedestrians, pets, or property may be harmed by objects

being thrown.

• Be aware of your environment while operating the snowthrower.

Don’t run over items such as gravel, doormats, newspapers, toys,

and rocks hidden under snow, as they can all be thrown from the

chute or jam in the auger.

• Use extreme caution when operating on or crossing gravel drives,

walks, or roads.

• Adjust the collector housing height to clear gravel or crushed rock

surface.

• Never operate the snowthrower near glass enclosures,

automobiles, window wells, drop-offs, and the like without proper

adjustment of the discharge chute angle.

• Familiarize yourself with the area in which you plan to operate the

snow thrower. Mark off boundaries of walkways and driveways.

DANGER

Objects can be picked up by auger and thrown

from chute. Never discharge snow toward

bystanders or allow anyone in front of the

snowthrower. Failure to observe these safety

instructions will result in death or serious

injury.

Thrown Objects

• Whenever cleaning, repairing, or inspecting the snowthrower,

make sure the engine is OFF, spark plug wire is disconnected,

and all moving parts have stopped.

• Do not put hands or feet near or under rotating parts. Keep clear

of the discharge opening at all times.

• Never operate the snowthrower without proper guards, and other

safety devices in place and working.

• Never leave the snowthrower unattended while engine is running.

Always disengage the auger and traction controls, stop engine,

and remove keys.

• Keep all loose clothing away from the front of the snowthrower

and auger. Scarves, mittens, dangling drawstrings, loose clothes,

and pants can quickly become caught in the rotating device and

amputation will occur. Tie up long hair and remove jewelry.

• Run the machine a few minutes after discharging snow to prevent

freeze-up of the collector/impeller.

• Disengage power to the collector/impeller when snowthrower is

transported or not in use.

DANGER

Keep hands, feet, and clothing away from

rotating parts. Rotating parts can contact or

entangle hands, feet, hair, clothing, or

accessories.

Failure to observe these safety instructions will

result in traumatic amputation or severe

laceration.

Moving Parts

Not for

Reproduction

OPERATOR SAFETY

• When performing any maintenance or repairs on the

snowthrower, shut OFF the engine, disconnect spark plug wire,

and keep the wire away from the plug to prevent someone from

accidently starting the engine.

• Check shear bolts and other hardware at frequent intervals for

proper tightness to be sure the snowthrower is in safe working

condition.

• Keep nuts and bolts tight and keep snowthrower in good

condition.

• Never tamper with safety devices. Check their proper operation

regularly and make necessary repairs if they are not functioning

properly.

• Components are subject to wear, damage, and deterioration.

Frequently check components and replace with recommended

parts, when necessary.

• Check control operation frequently. Adjust and service as

required.

• Use only factory authorized replacement parts or like parts when

making repairs.

• Always comply with factory specifications on all settings and

adjustments.

• Only authorized service locations should be utilized for major

service and repair requirements.

• Use only attachments and accessories approved by the factory

(such as wheel weights, counterweights, or cabs).

• Never attempt to make any adjustments while the engine is

running (except when specifically recommended by the factory).

WARNING

This snowthrower must be properly maintained

to ensure safe operation and performance.

Failure to observe the safety instructions in this

manual could result in death or serious injury.

Maintenance and Storage

• If there is natural or LP gas leakage in area, do not start engine.

• Do not use pressurized starting fluids because vapors are

flammable.

WARNING

Starting engine creates sparking.

Sparking can ignite nearby flammable gases.

Explosion and fire could result.

• Never touch a hot engine or muffler. Allow muffler, engine

cylinder, and fins to cool before touching.

• Remove debris from muffler area and cylinder area.

• Install and maintain in working order a spark arrester before using

equipment on forest-covered, grass-covered, or brush-covered

unimproved land.

• It is a violation of California Public Resource Code, Section 4442,

to use or operate the engine on any forest-covered, brush-

covered, or grass-covered land unless the exhaust system is

equipped with a spark arrester, as defined in Section 4442,

maintained in effective working order. Other states or federal

jurisdictions may have similar laws. Contact the original

equipment manufacturer, retailer, or dealer to obtain a spark

arrester designed for the exhaust system installed on this engine.

WARNING

Running the engine produces heat. Engine

parts, especially muffler, become extremely hot.

Failure to observe these safety instructions

could result in severe thermal burns on contact.

Engine Safety (Continued)

8www.brutepower.com

Not for

Reproduction

OPERATOR SAFETY

Safety Decals Figure 1

WARNING: If any safety decals become worn or

damaged and cannot be read, order replacement

decals from your local dealer.

Look for this symbol to indicate important safety

precautions. This symbol indicates: “Attention!

Become Alert! Your Safety Is At Risk.”

Before operating your snowthrower, read the safety decals as

shown on your snowthrower. The cautions and warnings are

for your safety. To avoid a personal injury or damage to your

snowthrower, understand and follow all the safety decals.

Part No. 1737865

Chute Danger Decal

Part No. 1736616

Shift Decal

Part No. 1737866

Auger Danger Decal

Product ID Number &

Serial Number Decal

(Rear of Motor Box)

Part No. 1737874

Main Dash Decal

Part No. 278297

Engine Decal

Part No. 1737869

Auger Control Decal

Part No. 1737870

Traction Control Decal

122

Not for

Reproduction

ASSEMBLY

TOOLS REQUIRED FOR ASSEMBLY

1–Knife

2 – 1/2” Wrenches (or adjustable wrenches)

1 – 7/16” Wrenches (or adjustable wrenches)

1 – Wrench (or adjustable wrench)

1 – Pair pliers or screw driver (to spread cotter pin)

1 – Hammer

1–Pry Bar

WARNING: Always wear safety glasses or eye shields

when assembling the snowthrower.

UNPACK THE SNOWTHROWER

1. Using knife, cut along the dotted lines around the top and

bottom of carton. Then remove carton material as shown in

Figure 2.

2. Remove shear pins and cotter pins from parts bag.

PARTS BAG CONTENTS

1 – Packet, Fresh Start™

1 – Shear Bolt Kit, 5/16-18 x 2 in.

1 – Bag of Shear Bolts

2 – Screw, 5/16-18 x 1.785 in.

2 – Locknut, Hex, 5/16-18

2 – Bolt, Carriage, 5/16-18 x 1-3/4 in.

2 – Nut, Hex Flange 5/16-18

1 – Pin, Hair (Chute Gear)

1 – Nut, Hex, 5/16-24

1 – Lockwasher, Spring, 5/16

Unpacking the Snowthrower Figure 2

Assembling the Handles Figure 3

ASSEMBLE THE HANDLES

1. Remove zip tie that secures handle to speed control.

2. Raise the upper handle (A, Figure 3) to the operating position.

3. Cut orange zip ties that secure control cables to the handle

assembly. Be careful not to cut or damage the control cables.

4. Slide two carriage bolts (B) into lower holes and fasten with

two 5/16” lock nuts (C). Tighten all four carriage bolts and nuts

with a 1/2” wrench or deep socket.

NOTE: Make sure the cables are not caught between the

upper and lower handles.

CHECK CABLE CONNECTION

The traction control cable (A, Figure 4) and auger control cable

(B) are adjusted at the factory and no adjustment should be nec-

essary.

If the cables become stretched, unattached or begin to sag, ad-

justment will be necessary. See Maintenance section of this

manual.

Checking Cable Connection Figure 4

10 www.brutepower.com

Not for

Reproduction

ASSEMBLY

INSTALL THE SPEED CONTROL ROD

Attach the ball joint (A, Figure 5), located on the bottom end of the

speed control rod (B), to the shift yoke assembly (C) with 5/16”

lock washer (D) and 5/16” nut (E).

Installing the Speed Control Rod Figure 5

ASSEMBLE THE CHUTE AND CRANK

See Figure 7 for instructions.

CHECK THE TIRES

Check tires for damage. Check the air pressure in the tires with an

accurate gauge. See the sidewall of the tire for the proper inflation.

CAUTION: Avoid Injury! Explosive separation of tire

and rim parts is possible when they are serviced

incorrectly.

• Do not attempt to mount a tire without the proper

equipment and experience to perform the job.

• Do not inflate the tires above the recommended pressure.

• Do not weld or heat a wheel and tire assembly. Heat can

cause an increase in air pressure resulting in an

explosion. Welding can structurally weaken or deform the

wheel.

• Do not stand in front or over the tire assembly when

inflating. Use appropriate tool that allows you to stand to

one side.

NOTICE: Check side of tire for maximum tire pressure. DO

NOT exceed maximum.

REMOVE SNOWTHROWER FROM PALLET

1. Remove straps that secure snowthrower to pallet.

2. Remove snowthrower from pallet.

IMPORTANT: DO NOT back over cable or loose parts.

3. Check level of skid shoes to ensure the same height on each

side.

INSTALL THE DRIFT CUTTERS

Drift cutters are used to cut a path through snow deeper than the

auger housing.

1. On each side of the auger housing, insert carriage bolt (A,

Figure 6) through upper hole.

2. Insert lower tab of drift cutter (B) into lower hole.

3. Secure with wing nuts (C).

Install the Drift Cutters Figure 6

Not for

Reproduction

1/2˝ (x 2) 7/16˝

17 lb-ft

23 Nm

15 lb-ft

(20 Nm)

Assemble the Chute and Crank Figure 7

ASSEMBLY

12 www.brutepower.com

Not for

Reproduction

FEATURES AND CONTROLS

SNOWTHROWER CONTROLS

A. Speed Select Lever — Allows the operator to use one of six

(6) forward and two (2) reverse speeds (see Figure 8). To

shift, move speed select lever to desired position.

NOTICE: Do not move speed select lever while Traction

Drive Clutch is engaged. This may result in severe dam-

age to drive system.

B. Auger Control Lever — Used to engage and disengage the

auger and impeller. To engage push down, to disengage re-

lease.

C. Traction Control Lever — Used to propel snowthrower for-

ward or reverse. Push down to engage, release to disengage.

Snowthrower Controls Figure 8

D. Snow Chute Deflector — Used to change the direction the

snow is thrown.

E. Crank — Used to change direction of the snow discharge.

Turn handle clockwise to turn chute to right. Turn handle coun-

terclockwise to turn chute to left.

F. Skid Shoe — Used to adjust ground clearance of auger

housing.

G. Clean-Out Tool — Used to remove snow and debris from the

discharge chute and the auger housing.

H. Free-HandTM Control — After engaging the traction control

(left hand) and auger control (right hand), allows the operator

to release the auger control lever to use the other controls.

Not for

Reproduction

SNOWTHROWER CONTROLS (Continued)

I. Deflector Control Lever — Push forward to discharge snow

high and far. Pull back to discharge snow down.

J. Headlight — Used to operate the snowthrower in poor light-

ing conditions.

K. Heated Hand Grips — When the engine is running, the

heated hand grips will automatically turn ON. After the engine

is shut off, the heated hand grips will automatically turn OFF.

ENGINE CONTROLS

A. Choke Control Knob — Used to start a cold engine (see

Figure 9).

B. Electric Start Button — Used to start the engine using the

electric starter.

Engine Controls Figure 9

C. Primer Button — Used to inject fuel directly into the carbure-

tor manifold to ensure fast starts in cool weather.

D. Safety Key — Must be inserted to start engine. Pull out to

stop. Do not turn safety key.

E. Starter Cord Handle — Used to start the engine manually.

F. ON/OFF Switch (if equipped) — Used to start and stop the

engine.

G. Fuel Tank and Cap — Fill the fuel tank to approximately

1-1/2 in. (38 mm) below the top of the neck to allow for fuel

expansion.

H . Oil Fill Cap (Extended Dipstick)

I. Fuel Shut-Off Valve — Used to turn the fuel supply off for

storage.

FEATURES AND CONTROLS

STOP

14 www.brutepower.com

Not for

Reproduction

Control Levers Figure 10

NOTICE: Do not throw snow toward a building as hidden ob-

jects could be thrown with sufficient force to cause dam-

age.

1. Start the engine. See Start the Engine in this section.

2. Rotate the crank (A, Figure 10) to set the direction (left or

right) of the discharge chute. See Discharge Chute and De-

flector in this section.

Free-HandTM Control

OPERATION

DANGER: The discharge chute contains a rotating

impeller to throw snow. Never clear or unclog the

discharge chute with your hands. Fingers can quickly

become caught and traumatic amputation or severe

laceration will result. Always use a clean-out tool to

clear or unclog the discharge chute.

WARNING: The operation of any snowthrower can result in foreign objects being thrown into the eyes, which can result in

severe eye damage. Always wear safety glasses or eye shields before beginning snowthrower operation. We recommend

standard safety glasses or Wide Vision Safety Mask over spectacles.

CAUTION: Before operating, make sure the area in

front of the snowthrower is clear of bystanders or

obstacles.

BEFORE OPERATING SNOWTHROWER

■

Check the fasteners. Make sure all fasteners are tight.

■

On electric start models, the unit was shipped with the

starter cord plugged into the engine. Before operating,

unplug the starter cord from the engine.

NOTE: This snowthrower was shipped WITH OIL in the

engine. See Check the Oil (Before Starting Engine)

instructions in this section before starting engine.

SNOWTHROWER SAFETY TESTS

Test 1 - Auger/Impeller

• Release auger control (right-hand).

• Auger/impeller stops in less than 5 seconds.

Test 2 - Traction Drive

• Release traction control (left-hand).

• Snowthrower forward/reverse motion stops.

Test 3 - Free-Hand Control (if equipped)

• Engage auger control and traction control.

• Release auger control immediately followed by the traction

control (a) stops auger/impeller in less than 5 seconds, and (b)

stops forward/reverse motion of snowthrower.

OPERATE THE SNOWTHROWER

CAUTION: Operation with a Snow Cab. Wind may blow

exhaust gasses back towards the operator. If you notice

the smell of exhaust, change direction of operation.

WARNING:

• Hand contact with the rotating impeller inside the

discharge chute is the most common cause of injury

associated with snowthrowers.

• This snowthrower is capable of amputating hands

and feet, and throwing objects. Read and observe all

the safety instructions in this manual. Failure to do so

will result in death or serious injury.

Not for

Reproduction

7. Use the speed select lever (E) to select the forward drive

speed. Set the speed select lever to one of the following posi-

tions as determined by snow conditions:

1-2 Wet, Heavy, Slushy, Extra Deep

3 Moderate

4-5 Very Light

6 Transport

NOTE: When clearing wet, heavy, snow, it is recommended

that the ground speed of the unit be reduced, maintained

full throttle and do not attempt to clear the full width of the

unit.

8. To stop moving forward, release the traction control lever (D).

9. To move the snowthrower backwards, move the speed select

lever into either first or second reverse position and engage

the traction control lever.

NOTE: Always release the traction control lever before mov-

ing the speed select lever.

3. Push the deflector control lever (B) forward or pull back to

control the angle of the chute deflector. See Discharge

Chute and Deflector in this section.

4. Fully press and hold the auger control lever (C) to engage the

auger rotation. Releasing the auger control lever will disen-

gage the auger - unless the Free-Hand™ control is activated.

5. Fully press and hold the traction/Free-Hand™ control lever (D)

to engage the traction drive and begin moving the snow-

thrower. To disengage the traction drive, completely release

the lever.

6. When BOTH levers are pressed, the Free-Hand™ control is

activated. This allows you to release the auger control lever to

use the other controls. The auger will continue to rotate until

the traction/Free-Hand™ control lever is released.

OPERATION

STOP THE SNOWTHROWER

1. Release the auger control lever (C, Figure 10).

2. Release the traction control lever (D).

3. Push the ON/OFF switch (A, Figure 19), if equipped, to the

OFF position and pull out the safety key (B).

WARNING: Read Operator’s Manual before operating

machine. This machine can be dangerous if used

carelessly.

• Never operate the snowthrower without all guards, covers,

and shields in place.

• Never direct discharge towards windows or allow

bystanders near machine while engine is running.

• Stop the engine whenever leaving the operating position.

• Disconnect spark plug before unclogging the impeller

housing or the discharge chute and before making repairs

or adjustments.

• When leaving the machine, remove the safety key. To

reduce the risk of fire, keep the machine clean and free

from spilled gas, oil, and debris.

WARNING: Never run engine indoors or in an

enclosed, poorly ventilated area. Engine exhaust

contains CARBON MONOXIDE, an ODORLESS and

DEADLY GAS.

• Keep hands, feet, hair, and loose clothing away from any

moving parts on engine and snowthrower.

• Temperature of muffler and nearby areas can exceed 150°F

(66°C). Avoid these areas.

• DO NOT allow children or young teenagers to operate or

be near snowthrower while it is operating.

16 www.brutepower.com

Not for

Reproduction

EASY-TURNTM TRACTION CONTROL

For easy turning when using the snowthrower, squeeze the Easy-

Tu r n TM lever (see Figure 11).

Engaging the Easy-TurnTM lever releases the left traction wheel but

allows the right wheel to continue driving. Releasing the Easy-

Tu r n TM lever automatically engages both drive wheels for full trac-

tion (see Figure 12).

NOTE: The Easy-TurnTM will be more difficult to activate

under a heavy load. Activate the lever before beginning a

turn.

Easy-TurnTM Control Figure 11

Full Traction Figure 12

OPERATION

Not for

Reproduction

OPERATION

DISCHARGE CHUTE AND DEFLECTOR

Discharge Chute Rotation (Left/Right)

1. Turn the chute rotation crank (A, Figure 13) clockwise to ro-

tate chute to the right.

2. Turn the chute rotation crank counterclockwise to rotate

chute to the left.

3. After the desired position is obtained, release the crank.

Chute Deflector (Up/ Down)

1. Push the deflector control lever FORWARD to provide a

higher stream and greater distance (B, Figure 13).

2. Pull the deflector control lever BACK to provide a lower

stream and less distance.

3. After the desired position is obtained, release the lever.

Discharge Chute and Deflector Figure 13

CHECK THE OIL (BEFORE STARTING ENGINE)

NOTE: The engine was shipped from the factory filled with

oil. Check the level of the oil. Add oil as needed.

1. Make sure the unit is level. Use a high quality detergent oil

classified “For Service SG, SH, SJ, SL, or higher”.

2. Remove the oil fill cap/dipstick (A, Figure 14) and wipe with a

clean cloth.

3. Insert the oil fill cap/dipstick and turn clockwise to tighten.

4. Remove the oil fill cap/dipstick and check the oil.

NOTE: Do not check the level of the oil while the engine

runs.

5. If necessary, add oil until the oil reaches the FULL mark on the

oil fill cap/dipstick. Do not add too much oil.

6. Tighten the oil fill cap/dipstick securely each time you check

the oil level.

NOTE: Synthetic 5W30 motor oil is acceptable for all

temperatures. DO NOT mix oil with gasoline. See Chart for

oil recommendations.

Checking the Oil Figure 14

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W-30 may cause increased oil

consumption. Check oil level more frequently.

FULL

18 www.brutepower.com

Not for

Reproduction

OPERATION

FUEL RECOMMENDATIONS

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use,

see below.

• Gasoline with up to 10% ethanol (gasohol) or up to 15%

MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE: Do not use unapproved gasolines, such as E85. Do

not mix oil in gasoline or modify the engine to run on

alternate fuels. This will damage the engine components

and void the engine warranty.

To protect the fuel system from gum formation, mix a fuel stabilizer

into the fuel. All fuel is not the same. If starting or performance

problems occur, change fuel providers or change brands. This

engine is certified to operate on gasoline. The emissions control

system for this engine is EM (Engine Modifications).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane/85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See a Briggs & Stratton Authorized Dealer for high

altitude adjustment information.

Operation of the engine at altitudes below 2,500 feet (762 meters)

with the high altitude kit is not recommended.

ADDING FUEL

1. Clean the fuel cap area of dirt and debris. Remove the fuel

cap (G, Figure 9).

2. Fill the fuel tank with fuel. To allow for expansion of the fuel,

do not fill above the bottom of the fuel tank neck.

3. Reinstall the fuel cap.

WARNING:

Fuel and its vapors are extremely flammable and

explosive.

Fire or explosion can cause severe burns or death.

When Adding Fuel

• Turn engine off and let engine cool at least 3 minutes before

removing the fuel cap.

• Fill fuel tank outdoors or in well-ventilated area.

• Do not overfill fuel tank. To allow for expansion of the fuel, do not

fill above the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• Check fuel lines, tank, cap, and fittings frequently for cracks or

leaks. Replace if necessary.

• If fuel spills, wait until it evaporates before starting engine.

Not for

Reproduction

OPERATION

Start the engine as follows:

1. Check the oil level.

2. Make sure equipment drive controls are disengaged.

3. Push the ON /OFF switch (A, Figure 15), if equipped, to the

ON position.

START THE ENGINE

Be sure that engine oil is at FULL mark on the oil fill cap/dipstick.

The snowthrower engine is equipped with an AC electric starter

and recoil starter. Before starting the engine, be certain that you

have read the following information.

If engine floods, set the choke to the OPEN/RUN position and

crank until the engine starts.

WARNING: The electric starter is equipped with a three-

wire power cord and plug designed to operate on AC

household current. The power cord must be properly

grounded at all times to avoid the possibility of electric shock

which can cause injury to the operator. Follow all instructions

carefully as set forth:

Make sure your house has a three-wire grounded system.

If you are not sure, ask a licensed electrician. If your house

does not have a three-wire grounded system, do not use this

electric starter under any condition.

If your house has a three-wire grounded system but a three-

hole receptacle is not available to connect the electric starter,

have a three-hole receptacle installed by a licensed electrician.

WARNING: To connect power cord, always connect the

power cord first to the switch box located on the

engine and then plug the other end into a three-hole

grounded receptacle.

WARNING: To disconnect the power cord, always

unplug the end connected to the three-hole grounded

receptacle first.

Starting Engine Figure 15

4. Insert the safety key (A, Figure 16) into the safety key slot and

push fully in to the RUN position.

5. Turn the choke knob (B) fully clockwise if engine is cold.

NOTE: Do not use the choke to start a warm engine.

6. Push the primer button (C) two times.

NOTE: Do not use the primer to start a warm engine.

NOTE: Ensure that electric extension cord is removed from

the power receptacle.

7. Rewind Start: Firmly hold the starter cord handle (A, Figure

17). Pull the starter cord handle slowly until resistance is felt,

then pull rapidly.

WARNING: Rapid retraction of the starter cord (kickback)

will pull your hand and arm toward the engine faster than

you can let go. Broken bones, fractures, bruises, or

sprains could result. When starting engine, pull the

starter cord slowly until resistance is felt and then pull

rapidly to avoid kickback.

NOTE: If the engine does not start after three attempts, see an

authorized dealer.

8. Electric Start: First connect the extension cord to the power

cord receptacle and then into a wall receptacle. If additional

extension cord is required, make sure it is three-wire.

WARNING: If the extension cord is damaged, it must be

replaced by the manufacturer (or its service agent) or a

similarly qualified person to avoid a hazard.

20 www.brutepower.com

Inserting Safety Key Figure 16

Not for

Reproduction

La page charge ...

Simplicity BRUTE DUAL STAGE SNOWTHROWER DOM, LF 16.5TP 33 INCH (83,8 CM) Manuel utilisateur

Marque: Simplicity

Modèle: BRUTE DUAL STAGE SNOWTHROWER DOM, LF 16.5TP 33 INCH (83,8 CM)

Catégorie: Souffleuses à neige

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity BRUTE DUAL STAGE SNOWTHROWER DOM, LF 16.5TP 33 INCH (83,8 CM) User manual