Jasco 14326/ZW3006 Manuel utilisateur

Marque: Jasco

Modèle: 14326/ZW3006

Taper: Manuel utilisateur

Z-Wave® Certiﬁed Wireless Lighting Control

Certiﬁé Z-Wave Commande d’éclairage sans ﬁl

Control inalámbrico para iluminación certiﬁcado por Z-Wave®

14326

ZW3006

In-wall Wireless

Smart Dimmer (1000w)

Montage mural

Intelligent Gradateur

sans ﬁl (1000w)

Interruptor de pared

reductor inalámbrico

de luz inteligente (1000w)

White (Neutral)

Green (Ground)

Black (Line / Hot)

Z-Wave

Single

Switch

Black

(Load)

Scan to view

installation guide

Balayez ce code pour

consulter le guide

d’installation.

Escanear para ver

la guía de instalación

MANUAL • MANUEL • MANUAL

14326 UL v2

WARRANTY

JASCO Products warrants this product to be free from manufacturing defects for a period of

two years from the original date of consumer purchase. This warranty is limited to the repair or

replacement of this product only and does not extend to consequential or incidental damage to

other products that may be used with this product. This warranty is in lieu of all other warranties,

expressed or implied. Some states do not allow limitations on how long an implied warranty

lasts or permit the exclusion or limitation of incidental or consequential damage, so the above

limitations may not apply to you. This warranty gives you specic rights, and you may also have

other rights which vary from state to state. Please contact Customer Service at 800-654-8483

(option 1) between 7:30AM – 5:00PM CST or via our website (www.jascoproducts.com) if the

unit should prove defective within the warranty period.

GARANTIE

JASCO Products garantit que ce produit est exempt de tout défaut de fabrication pour une

période de deux ans à compter de la date de l’achat original par l’acheteur. Cette garantie se

limite exclusivement à la réparation ou au remplacement de ce produit et n’est pas applicable

aux dommages indirects ou accessoires survenus sur d’autres produits utilisés avec ce

produit. Cette garantie se substitue à toute autre garantie expresse ou implicite. Certains

États ne permettent pas de restrictions quant à la durée d’une garantie implicite ou permettent

l’exclusion ou la limitation des dommages indirects et accessoires; il se peut, par conséquent,

que cette garantie ne s’applique pas dans votre cas. Cette garantie vous confère des droits

juridiques précis; vous pouvez jouir d’autres droits qui peuvent varier d’un État à l’autre. Veuillez

communiquer avec le service à la clientèle au 1-800-654-8483 (option 1) entre 7 h 30 et 17 h

(heure normale du Centre) ou par l’intermédiaire de notre site Web (www.jascoproducts.com) si

l’appareil s’avère défaillant au cours de la période de garantie.

GARANTÍA

JASCO Products garantiza que este producto está libre de defectos de fabricación durante

un periodo de dos años a partir de la fecha original de compra por parte del consumidor. Esta

garantía se limita a la reparación o sustitución de este producto solamente y no se extiende

a daños derivados o accidentales causados a otros productos que se usen con esta unidad.

Esa garantía remplaza a todas las demás garantías expresas o implícitas. Algunos estados no

autorizan limitaciones en cuanto a la duración de una garantía implícita ni permiten la exclusión

o limitación por daños accidentales o derivados; por lo tanto, puede que las anteriores

limitaciones no apliquen en su caso. Esta garantía le da a usted derechos especícos, y otros

que usted puede tener y que varían según el estado en el que usted reside. Si la unidad

resultare defectuosa dentro del periodo de garantía, comuníquese por favor con Atención al

Cliente en el 800-654-8483 (opción 1) entre 7.30 y 17 h, Hora del Centro, o a través de nuestro

sitio de internet.

JASCO Products Company, Building B

10 E Memorial Rd. Oklahoma City, OK 73114

SPECIFICATIONS

ZW3006

Power: 120 VAC, 60 Hz.

Signal Frequency: 908.4/916 MHz.

Minimum Load: 40W, incandescent lamps only.

Maximum Loads: 1000W, 2-gang 800W, and 3-gang 600W incandescent lamps only.

Wireless Range: Up to 150 feet line of sight from controller or closest Z-Wave receiver module.

Operating Temperature Range: 32-104° F (0-40° C)

For indoor use only.

Specications subject to change without notice due to continuing product improvement

SPÉCIFICATIONS

ZW3006

Power: 120 VAC, 60 Hz.

Signal Frequency: 908.4/916 MHz.

Minimum Load: 40W, incandescent lamps only.

Maximum Loads: 1000W, 2-gang 800W, and 3-gang 600W incandescent lamps only.

Wireless Range: Up to 150 feet line of sight from controller or closest Z-Wave receiver module.

Operating Temperature Range: 32-104° F (0-40° C)

For indoor use only.

Specications subject to change without notice due to continuing product improvement

ESPECIFICACIONES:

ZW3006

Power: 120 VAC, 60 Hz.

Signal Frequency: 908.4/916 MHz.

Minimum Load: 40W, incandescent lamps only.

Maximum Loads: 1000W, 2-gang 800W, and 3-gang 600W incandescent lamps only.

Wireless Range: Up to 150 feet line of sight from controller or closest Z-Wave receiver module.

Operating Temperature Range: 32-104° F (0-40° C)

For indoor use only.

Specications subject to change without notice due to continuing product improvement

MADE IN CHINA/FABRIQUÉ EN CHINE/HECHO EN CHINA

DISTRIBUTED BY

JASCO PRODUCTS COMPANY LLC,

10 E. MEMORIAL RD.,

OKLAHOMA CITY, OK 73114.

The Jasco Add-on switch is required for Multi-Switch 3-way or 4-way installations.

Connecting the traveler terminal of this switch to a standard, non-Jasco switch will cause damage or result in improper

function. If this switch is a part of a 3-way or 4-way multi-switch installation, do not connect the traveler wire or apply

power until Jasco Add-on switches are correctly installed. For more information on 3-Way or 4-Way installations, view

the manual or quick-start guide that comes with the Jasco Add-on switch.

This Device supports Lifeline (association group 1) supporting 1 node for lifeline communication. Group 1 must be

assigned the Node ID of the primary controller where unsolicited notiﬁcations will be sent. The Z-Wave controller

should set this association automatically after inclusion. Lifeline association only supports the “Device Reset

Locally” function. Refer to the instructions of your controller for any available details on how this can be set.

Z-WAVE INTEROPERABILITY

This product can be included and operated in any Z-Wave network with

other Z-Wave certiﬁed devices from other manufacturers and/or other

applications. All non-battery operated nodes within the network will act

as repeaters regardless of vendor to increase reliability of the network.

5. To Change Color Of The Paddle

This step is optional. Before you start you may want

to change the color of the paddle to match your

wallplate or decor.

1. Lift the Air Gap tab at the base of the paddle.

2. Push side tabs in on one side and then the other

to release paddle. Lift the cover up and off.

3. Simply put the new paddle onto the switch by

inserting the air gap and side tabs and snapping

securely into place.

Once this step has been completed

please return to section 3.

All brand names shown are trademarks of their

respective owners.

Tous les noms de marque illustrés sont des

marques de commerce de leurs propriétaires

respectifs.

Todas las marcas que aparecen aquí son

marcas registradas de sus respectivos dueños.

From Breaker Box

Out to Light (Load)

From Breaker Box

Out to Light (Load)

If you have any problems or questions, contact our tech support team

at; 1-800-654-8483, option 1 Monday–Friday, 7:30–5pm CST

For the most up-to-date product support, accessories, electronic (PDF) format

manuals and more, visit www.jascoproducts.com/support.

• No user servicable parts in this unit.

Si vous avez des problèmes ou des questions, communiquez avec notre

équipe de soutien technique au 1-800-654-8483, option1, du lundi au

vendredi, de 7 h 30 à 17 h (HNC).

Pour le soutien relatif aux produits le plus à jour, les accessoires,

les manuels en format électronique (PDF) et plus encore, visitez le site

www.jascoproducts.com/support.

• Aucune des pièces de ce dispositif ne peut être réparée par l’utilisateur.

Si tiene problemas o dudas, comuníquese con nuestro equipo técnico al

número: 1-800-654-8483, opción 1 de lunes a viernes, de 7:30 a 5 p.m., hora

estándar del centro (CST).

Para recibir el soporte técnico más actualizado sobre productos,

accesorios, manuales en formato digital (PDF), entre otros,

visite www.jascoproducts.com/support.

• Esta unidad no contiene piezas que el usuario pueda reparar.

STOP

DO NOT RETURN THIS

PRODUCT TO THE STORE

NE RETOURNEZ PAS

CE PRODUIT AU MAGASIN

NO DEVUELVA ESTE

PRODUCTO A LA TIENDA.

RISK OF FIRE

RISK OF ELECTRICAL SHOCK

RISK OF BURNS

CONTROLLING APPLIANCES:

CAUTION: TO REDUCE THE RISK OF OVERHEATING

AND POSSIBLE DAMAGE TO OTHER EQUIPMENT,

DO NOT INSTALL TO CONTROL A MOTOR-

OPERATED APPLIANCE, A FLUORESCENT

LIGHTING FIXTURE, OR A TRANSFORMER

SUPPLIED APPLIANCE.

• ONLY USE TO CONTROL INCANDESCENT OR

DIMMABLE CFL/LED BULBS

• DO NOT EXCEED RATINGS

• DO NOT USE TO CONTROL ANY DEVICE WHERE

UNINTENDED OPERATION COULD CAUSE

UNSAFE CONDITIONS (HEAT LAMP, SUN LAMP,

ETC.)

• FOR INDOOR USE ONLY

RIESGO DE INCENDIO

RIESGO DE DESCARGA ELÉCTRICA

RIESGO DE QUEMADURAS

CONTROL DE APARATOS:

PRECAUCIÓN: A FIN DE DISMINUIR EL RIESGO

DE RECALENTAMIENTO Y DE POSIBLES DAÑOS

EN LOS DEMÁS EQUIPOS, NO INSTALAR PARA

CONTROLAR APARATOS QUE FUNCIONAN A

MOTOR, ARTEFACTOS DE ILUMINACIÓN DE LUZ

FLUORESCENTE O APARATOS ALIMENTADOS CON

TRANSFORMADORES.

• USAR EXCLUSIVAMENTE PARA CONTROLAR

BOMBILLAS CFL/LED INCANDESCENTES O

ATENUABLES

• NO SUPERE LOS VALORES NOMINALES

ELÉCTRICOS

• NO USAR PARA CONTROLAR DISPOSITIVOS

• USE SOLAMENTE EN INTERIORES

NOT FOR USE WITH MEDICAL OR LIFE

SUPPORT EQUIPMENT

Z-WAVE ENABLED DEVICES SHOULD NEVER BE

USED TO SUPPLY POWER TO, OR CONTROL

THE ON/OFF STATUS OF MEDICAL AND/OR LIFE

SUPPORT EQUIPMENT.

NE PAS UTILISER AVEC UN ÉQUIPEMENT

MÉDICAL OU DE SURVIE

LES DISPOSITIFS COMPATIBLES AVEC LA

TECHNOLOGIE Z-WAVE NE DEVRAIENT

JAMAIS ÊTRE UTILISÉS POUR ALIMENTER OU

COMMANDER LA MISE EN MARCHE OU L’ARRÊT DE

L’ÉQUIPEMENT MÉDICAL OU DE SURVIE.

SE PROHÍBE SU EMPLEO EN

EQUIPO MÉDICO O EQUIPO PARA EL

MANTENIMIENTO DE LAS FUNCIONES

VITALES

LOS DISPOSITIVOS Z-WAVE NUNCA SE DEBEN

USAR PARA SUMINISTRAR ENERGÍA ELÉCTRICA

AL EQUIPO MÉDICO O AL EQUIPO PARA EL

MANTENIMIENTO DE FUNCIONES VITALES, NI

PARA CONTROLAR EL ESTADO DE ENCENDIDO O

APAGADO DE DICHOS EQUIPOS.

RISQUE D’INCENDIE

RISQUE DE CHOC ÉLECTRIQUE

RISQUE DE BRÛLURES

COMMANDE DES APPAREILS:

ATTENTION: POUR RÉDUIRE LE RISQUE DE

SURCHAUFFE ET DE DOMMAGES POSSIBLES

À D’AUTRES APPAREILS, NE PAS INSTALLER

POUR COMMANDER UN APPAREIL ACTIONNÉ

PAR MOTEUR, UN APPAREIL D’ÉCLAIRAGE

FLUORESCENT OU UN APPAREIL ALIMENTÉ PAR

UN TRANSFORMATEUR.

• UTILISER SEULEMENT POUR COMMANDER

LES AMPOULES À DEL ET FLUOCOMPACTES À

INCANDESCENCE OU À INTENSITÉ RÉGLABLE

• NE PAS DÉPASSER LES CARACTÉRISTIQUES

NOMINALES

• NE PAS UTILISER POUR COMMANDER

DES APPAREILS POUR LESQUELS UN

FONCTIONNEMENT IMPRÉVU POURRAIT

ENTRAÎNER DES CONDITIONS DANGEREUSES

(LAMPE À RAYONS INFRAROUGES, LAMPE

SOLAIRE, ETC.)

• POUR UTILISATION INTÉRIEURE UNIQUEMENT

AVERTISSEMENT

WARNING ADVERTENCIA

This device complies with part 15 of the FCC and Industry Canada license-exempt RSS

standard(s). Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modications to this equipment. Such modications could void the user’s authority

to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.

— Increase the separation between the equipment and receiver.

— Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

— Consult the dealer or an experienced radio/TV technician for help

Important note: To comply with the FCC RF exposure compliance requirements, no change

to the antenna or the device is permitted. Any change to the antenna or the device could result

in the device exceeding the RF exposure requirements and void user’s authority to operate the

device.

FCC / IC

Este dispositivo cumple con las Especicaciones del apartado 15 de las normas de la FCC y con

las especicaciones de las normas radioeléctricas (RSS) del Ministerio de Industria de Canadá

aplicables a aparatos exentos de licencia. El funcionamiento está sujeto a las siguientes dos

condiciones: (1) este dispositivo no debe provocar interferencia perjudicial, y (2) este dispositivo

debe aceptar toda interferencia que reciba, incluso la que pudiera causar un funcionamiento no

deseado.

NOTA DE LA FCC: El fabricante no se hace responsable de ninguna interferencia de radio o TV

ocasionada por modicaciones no autorizadas efectuadas a este equipo. Dichas modicaciones

podrían anular la autoridad del usuario para utilizar el equipo.

NOTA: Este equipo ha sido probado y cumple con los límites para aparatos digitales de Clase B,

de conformidad con el apartado 15 de las normas de la FCC. Estos límites están diseñados para

proveer protección razonable contra interferencias perjudiciales en una instalación residencial.

Este equipo genera, usa y puede irradiar energía de radiofrecuencias y, si no se instala y usa

según las instrucciones, puede provocar interferencia perjudicial a las radiocomunicaciones. No

obstante, no hay garantías de que no ocurrirá interferencia en una instalación en particular. Si

este equipo provoca interferencia perjudicial a la recepción de radio o televisión, lo que puede

determinarse encendiendo y apagando el equipo, se recomienda que el usuario intente corregir

interferencia por medio de la implementación de una o más de las siguientes medidas:

— Reorientar o reubicar la antena receptora.

— Incrementar la separación entre el equipo y el receptor.

— Conectar el equipo a un tomacorriente de un circuito diferente del circuito al que está

conectado el receptor.

— Consultar al distribuidor o a un técnico con experiencia en radio/televisión para

solicitar asistencia.

Nota importante: Para cumplir con los requisitos de cumplimiento de exposición de

radiofrecuencia de la FCC, no se permiten cambios a la antena o el dispositivo. Cualquier cambio

a la antena o dispositivo podría hacer que el dispositivo supere los requerimientos de exposición

de radiofrecuencia y anular la autoridad del usuario para operar el dispositivo.

FCC — U2ZZW3006A | IC: 6924A-ZW3006A

Jasco Products Company | Model: ZW3006 / 14326

CAN ICES-3(B) / NMB-3(B)

Cet appareil est conforme au paragraphe 15 des normes FCC et au CNR pour les appareils

exempts de licence d’Industrie Canada. Son utilisation est sujette aux deux conditions suivantes :

1) cet appareil ne doit pas occasionner de brouillage préjudiciable et 2) cet appareil doit

accepter toutes les interférences reçues, notamment les interférences qui peuvent provoquer un

fonctionnement non désiré.

NOTE DE LA FCC : Le fabricant n’est pas responsable des interférences sur les fréquences

radioélectriques ou télévisuelles pouvant être causées par des modications non autorisées de

ce matériel. De telles modications peuvent annuler le droit de l’utilisateur à utiliser cet appareil.

REMARQUE : Cet appareil a été testé et certié conforme aux limites relatives aux appareils

numériques de catégorie B dénies dans le paragraphe 15 des normes FCC. Ces limites ont

été dénies an de fournir une protection raisonnable contre le brouillage préjudiciable en milieu

résidentiel. Cet appareil produit, utilise et peut émettre des ondes de fréquence radio et, s’il n’est

pas installé et utilisé conformément aux instructions, il peut provoquer un brouillage préjudiciable

aux communications radio. Il n’existe toutefois aucune garantie que des interférences ne se

produiront pas au sein d’une installation donnée. Si cet appareil occasionne un brouillage

préjudiciable à la réception radiophonique ou télévisuelle, il suft d’allumer et d’éteindre l’appareil

pour déterminer sa responsabilité. Nous encourageons l’utilisateur à essayer de corriger ces

interférences en appliquant une ou plusieurs des mesures suivantes :

— Réorienter ou déplacer l’antenne de réception.

— Augmenter la distance entre l’appareil et le récepteur.

— Brancher l’appareil à une prise secteur différente de celle du récepteur.

— Consulter le revendeur ou un technicien spécialisé en postes radio ou téléviseurs.

Remarque importante : Pour se conformer aux exigences de conformité de la FCC concernant

l’exposition aux RF, aucune modication apportée à l’antenne ou au dispositif n’est autorisée.

Toute modication apportée à l’antenne ou au dispositif pourrait faire en sorte que le dispositif

dépasse les exigences d’exposition aux RF et pourrait annuler le droit de l’utilisateur à utiliser ce

dispositif.

Out to Light (Load)

From Breaker Box

Multi-switch wiring

For 3-way installations, please refer to Add-on Switch manual

Single switch wiring

Before you start; you may wish to change the paddle to match your wallplate or decore.

Please proceed to section 5.

1. Shut off power to the circuit at circuit breaker or fuse box.

IMPORTANT! Verify power is OFF to switch box before continuing.

2. Remove wall plate.

3. Remove the switch mounting screws.

4. Carefully remove the switch from the switch box. DO NOT disconnect the wires.

There are up to four screw terminals on the switch; these are marked

A. LINE (Hot) — Black (connected to power)

WARNING — SHOCK HAZARD

Turn OFF the power to the branch circuit for the switch and lighting xture at the

service panel. All wiring connections must be made with the POWER OFF to avoid

personal injury and/or damage to the switch.

This device is intended for installation in accordance with the National Electric Code

and local regulations in the United States, or the Canadian Electrical Code and local

regulations in Canada. If you are unsure or uncomfortable about performing this

installation consult a qualied electrician.

B. NEUTRAL — White (this terminal is not used for the installation process)

C. LOAD — Black (connected to lighting)

D. GROUND — Green/Bare

E. TRAVELER — Red/Other (only in 3-way installations)

Match these screw terminals to the wires connected to the existing switch.

5. Disconnect the wires from the existing switch. Be careful to label wires according to the

previous terminal connection.

Observe Important Wiring Information

IMPORTANT!: This Dimmer is rated for and intended to only be used with copper wire.

Wire Gauge Requirements

Use 14 AWG or larger wires suitable for at least 80° C for supplying Line (HOT), Load,

Neutral, Ground and Traveler connections.

Wire strip length:

For attachment to screw terminals: Strip insulation 1” (25mm)

For attachment using the enclosure’s holes: Strip insulation 5/8” (16mm)

UL species that the tightening torque for the screws is 14 Kgf-cm (12 lbf-in).

1. Connect the green or bare copper ground wire to the GROUND terminal.

2. Connect the black wire that goes to the light to the terminal marked LOAD.

3. Connect the black wire that comes from the electrical service panel (Hot) to the terminal

marked LINE.

4. Connect the white wire to the neutral terminal (use jumper wire [not included] if needed).

Note: The Traveler terminal is only used for 3-way or 4-way wiring and should remain

insulated if the switch is being installed in a 2-way system (one switch & one load).

5. Insert Dimmer into the switch box being careful not to pinch or crush wires.

6. Secure the Dimmer to the box using the supplied screws.

7. Mount the wall plate.

8. Reapply power to the circuit at fuse box or circuit breaker and test the system.

Basic Operation

The connected light can be turned ON/OFF and adjust dim levels in two ways:

1. Manually from the front panel of the In-wall Dimmer

2. Remotely with a Z-Wave Controller

Manual Control

The Front Panel Rocker Dimmer allows the user to:

Turn ON/OFF the connected xture.

To turn the connected xture ON: Press and release the top of the rocker.

To turn the connected xture OFF: Press and release the bottom of the rocker.

Adjust dim level

To increase brightness: press and hold the top of the rocker

To decrease brightness: press and hold the bottom of the rocker.

1. Tools You Will Need

• Turn ON/OFF and adjust dim levels manually or remotely via the Z-Wave controller

• Can be Included in multiple Groups and Scenes

• May be used in single pole installation or with up to two Jasco Add-on switches in 3-way or

4-way wiring conﬁgurations

• Compatible with incandescent and halogen bulbs only

• Interchangeable Paddle switch — White & light almond paddle in package

• Uses a standard, decorative-size wall plate for single gang installations (wall plate not included)

• Blue LED indicates switch location in a dark room

• Z-Wave Certiﬁed for simple pairing and integrated home automation

• Screw Terminal Installation — requires wiring connections for Line (Hot), Load, Neutral, and

Ground. Traveler wire required for 3-way or 4-way installation

• This device supports lifeline (association group 1)

• This Z-Wave device has advanced features that allow you to customize your experience.

These features can only be adjusted by a Z-Wave enabled controller that support the

Z-Wave Conﬁguration command class. For a complete list of Adjustable Conﬁgurations,

visit: www.jascoproducts.com/z-waveconﬁg

Getting To Know Your New Z-Wave Device

IMPORTANT!

The xture controlled by the Z-Wave In-wall Smart Dimmer must not exceed

1000 watts (Incandescent). Not for use with CFL or LED lighting.

Single, Dual And Triple Gang Boxes

When installing the In-wall Smart Dimmer in multiple gang boxes it may be

necessary to break off one or both sides of the scored tabs on the front yoke.

This will affect the electrical rating of the switch (see speciﬁcations for details).

A. Top Rocker — (Press &

release to turn Dimmer on,

press & hold increases

brightness)

B. Bottom Rocker — (Press

& release to turn Dimmer off,

press & hold to dim)

C. Ground (Green/Bare)

D. Load (Black)

E. Line (Black)

F. Traveler (Red/Other)

Adding your device to a Z-wave network

1. Follow the instructions for your Z-wave certiﬁed controller to include a device to the Z-wave

network.

2. Once the controller is ready to include your device, press and release the top or bottom of the

wireless smart switch(rocker) to include it in the network.

3. Once your controller has conﬁrmed that the device has been included, refresh the Z-wave network

to optimize performance.

Please reference the controller’s manual for instructions.

Now you have complete control to turn your ﬁxture ON/OFFaccording to groups, scenes, schedules

and interactive automations programmed by your controller.

If your Z-wave certiﬁed controller features Remote Access, you can now control your ﬁxture from

your mobile devices.

To exclude and reset the device

1. Follow the instructions for your Z-wave certiﬁed controller to exclude a device from the Z-wave

network.

2. Once the controller is ready to Exclude your device, press and release the top or bottom of the

wireless smart dimmer (rocker) to exclude it from the network.

To return your switch to factory defaults:

Quickly press ON (Top) button three (3) times then immediately press the OFF (Bottom) button three

(3) times. The LED will ﬂash ON/OFF 5 times when completed successfully.

Note: This should only be used in the event your network’s primary controller is

missing or otherwise inoperable.

Model: 14326 / ZW3006

Thisliteraturewillbeavailableonourquickstartguideoronourwebsiteatthefollowingaddressin

thefuture:www.jascoproducts.com/z‐waveconfig

ADVANCED OPERATION

The following Advanced Operation parameters require that you have a controller that supports the advanced

configuration command class.

All On/All Off

Depending upon your primary controller, this Z-Wave module can be set to respond to ALL ON and ALL OFF

commands in up to four different ways. Some controllers may not be able to change the response from its default

setting. Please refer to your controller’s instructions for information on whether or not it supports the configuration

function and if so, how to change this setting.

The four possible responses are:

1. It will respond to ALL ON and the ALL OFF commands (default).

2. It will not respond to ALL ON or ALL OFF commands.

3. It will respond to the ALL OFF command but will not respond to the ALL ON command.

4. It will respond to the ALL ON command but will not respond to the ALL OFF command.

LED Light

When shipped from the factory, the LED is set to turn ON when the connected light is turned OFF. This is the

default setting and can be changed if your primary controller supports the node configuration function. To make the

LED turn ON when the light is turned ON, change parameter 3’s value to “1”. To turn the LED OFF at all times,

change parameter 3’s value to 2.

• Parameter No: 3

• Length: 1 Byte

• Valid Values = 0, 1 or 2 (default 0)

Invert Switch

If the switch is accidentally installed upside down with “On” at the bottom and “Off” at the top, the default On/Off

rocker settings can be reversed by changing parameter 4’s value to “1”.

• Parameter No: 4

• Length: 1 Byte

• Valid Values = 0 or 1 (default 0)

Dim Rate Adjustments

Both the number of steps (or levels) that the dimmer will change and the timing of the steps can be modified to suit

personal preferences. The timing of the steps can be adjusted in 10 millisecond intervals.

1. When Receiving a Z-Wave Dim Command

• Parameter 7 (number of steps or levels)

• Parameter 8 (timing of the steps)

• Length: 2 Byte

• Valid Values:

Parameter 7 (default = 1) Valid Values: 1-99

Parameter 8 (default = 3) Valid Values: 1-255

2. Manual Control Dimming (pressing the Dimmer’s rocker)

• Parameter 9 (number of steps or levels)

• Parameter 10 (timing of the steps)

• Length: 2 Byte

• Valid Values:

Parameter 9 (default = 1) Valid Values: 1-99

Parameter 10 (default = 3) Valid Values: 1-255

3. When Receiving an All-On or All-Off Command

• Parameter 11 (number of steps or levels)

• Parameter 12 (timing of the steps)

• Length: 2 Byte

• Valid Values:

Parameter 11 (default = 1) Valid Values: 1-99

Parameter 12 (default = 3) Valid Values: 1-255



Jasco 14326/ZW3006 Manuel utilisateur

Marque: Jasco

Modèle: 14326/ZW3006

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Jasco 14326/ZW3006 User manual
español: Jasco 14326/ZW3006 Manual de usuario

Jasco 14326/ZW3006 Manuel utilisateur

Jasco 14326/ZW3006 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents