Estate T8RXNGFWD01 Manuel utilisateur

Marque: Estate

Modèle: T8RXNGFWD01

Catégorie: Frigos

Taper: Manuel utilisateur

BYWHIRLPOOL CORPORATION

REFRIGERATORUSE& CARE GUIDE

MANUAL DE USO Y CUIDADO DELREFRIGERADOR

GUIDE D'UTILISATIONETD'ENTRETIENDU

REFRIGERATEUR

Table of Contents / Indice / Table des mati@res

ASSISTANCE OR SERVICE ............................ 1

REFRIGERATOR SAFETY ............................... 2

INSTALLATION INSTRUCTIONS ................... 3

REFRIGERATOR USE ..................................... 9

REFRIGERATOR CARE ................................. 10

TROUBLESHOOTING .................................... 11

WARRANTY .................................................... 13

AYUDA O SERVIClO TF=CNICO .................... 14

SEGURIDAD DEL REFRIGERADOR ............ 14

INSTRUCCIONES DE INSTALACION .......... 15

USO DE SU REFRIGERADOR ...................... 22

CUIDADO DE SU REFRIGERADOR ............. 23

SOLUClON DE PROBLEMAS ....................... 24

GARANTiA ...................................................... 26

ASSISTANCE OU SERVICE .......................... 27

SE_CURITE_DU RE_FRIGE_RATEUR................ 27

INSTRUCTIONS D'INSTALLATION .............. 28

UTILISATION DU RF=FRIGF=RATEUR ........... 35

ENTRETIEN DU RleFRIGleRATEUR ............. 36

DlePANNAGE .................................................. 37

GARANTIE ...................................................... 3g

AssistanceorService

If you need assistance or service, first see the "Troubleshooting"

section. Additional help is available by calling us at

1-800-253-1301 from anywhere in the U.S,A., or write:

Estate Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your appliance to help

you obtain assistance or service if you ever need it, You will need

to know your complete model number and serial number. You can

find this information on the model and serial number label, located

on the inside wall of the refrigerator compartment.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

2316077

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the refrigerator, follow basic precautions,

including the following:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,

away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker

kit ready models only).

SAVE THESE INSTRUCTIONS

Proper Disposalof YourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are still dangerous

- even if they will sit for "just a few days." Ifyou are getting rid of

your old refrigerator, please follow these instructions to help avoid

accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily

climb inside.

INSTALLATIONINSTRUCTIONS

......._...................III@ ........ sj,,,,, ..........

Excessive Weight Hazard

Use two or more people to move and install

refrigerator.

Failure to do so can result in back or other injury.

Remove the Packaging

Do not use sharp instruments, rubbing alcohol, flammable fluids,

or abrasive cleaners to remove tape or glue. These products can

damage the surface of your refrigerator. For more information, see

"Refrigerator Safety."

IMPORTANT: Do not remove the white foam air return insert from

behind the control panel on the ceiling of the refrigerator. If the

insert is removed, ice may migrate down from the freezer and

cause icicles to form.

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator

for cleaning or service, be sure to protect the floor.

Always pull the refrigerator straight out when moving it.

Do not wiggle or "walk" the refrigerator when trying to move

it, as floor damage could occur.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the cleaning instructions in

"Refrigerator Care."

important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to

sudden temperature changes or impact, such as bumping.

For your protection, tempered glass is designed to shatter

into many small, pebble-size pieces. This is normal. Glass

shelves and covers are heavy. Use special care when

removing them to avoid impact from dropping.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

To ensure proper ventilation for your refrigerator, allow for a 1/2"

(12.70 mm) space on each side. Allow 3" (7.5 cm) of space

between overhead cabinets and refrigerator top. Allow at least 1"

(25.40 mm) between back of cabinet and the wall. Ifyour

refrigerator has an ice maker, make sure you leave some extra

space at the back for the water line connections.

• If you are installing your refrigerator next to a fixed wall, leave

2" (5.08 cm) minimum on the hinge side (depending on your

model) to allow for the door to swing open.

• Level the refrigerator. See "Adjust the Doors."

NOTE: It is recommended that you do not install the refrigerator

near an oven, radiator, or other heat source. Do not install in a

location where the temperature will fall below 55°F (13°C).

3" (7.5cm) / I

II I

_11I

2" (5.08cm)

ElectricalShock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded

electrical supply is required. It is recommended that a separate

circuit serving only your refrigerator be provided. Use an outlet

that cannot be turned off by a switch. Do not use an

extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn the control (Thermostat, Refrigerator or

Freezer Control depending on the model) to OFF and then

disconnect the refrigerator from the electrical source. When you

are finished, reconnect the refrigerator to the electrical source and

reset the control (Thermostat, Refrigerator or Freezer Control

depending on the model) to the desired setting.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

IMPORTANT:

• If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

• All installations must meet local plumbing code requirements.

• Use copper tubing and check for leaks. Install copper tubing

only in areas where the household temperatures will remain

above freezing.

TOOLS NEEDED: Flat-blade screwdriver, 7A6"and 1/211open-end

wrenches or two adjustable wrenches, 1/4"nut driver and drill bit,

hand drill or electric drill (properly grounded).

NOTE: Your refrigerator dealer has a kit available with a %"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing.

Before purchasing, make sure a saddle-type valve complies with

your local plumbing codes. Do not use a piercing-type or 3/_6"

(4.76 mm) saddle valve which reduces water flow and clogs more

easily.

Water Pressure

A cold water supply with water pressure of between 30 and

120 psi (207-827 kPa) is required to operate ice maker. Ifyou have

questions about your water pressure, call a licensed, qualified

plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 - 827 kPa)

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 - 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 - 414 kPa):

• Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Read all directions before you begin.

IMPORTANT: Ifyou turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a//2" to 1W' (1.27 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

• Make sure it is a cold water pipe.

• Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

Determine the length of copper tubing you will need. Measure

from the connection on lower left rear of refrigerator to the

water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"

(6.35 mm) O.D. (outside diameter) copper tubing. Be sure both

ends of copper tubing are cut square.

Using a grounded drill, drill a W' hole in the cold water pipe

you have selected.

G ..................B

A. Cold waterpipe E.Compression sleeve

B. Pipe clamp F. Shutoff valve

C. Copper tubing G.Packingnut

D. Compressionnut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the W' drilled hole in

the water pipe and that the washer is under the pipe clamp.

Tighten the packing nut. Tighten the pipe clamp screws slowly

and evenly so washer makes a watertight seal. Do not

overtighten or you may crush the copper tubing.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the

outlet end squarely as far as it will go. Screw compression nut

onto outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn

ON the main water supply. Flush the tubing until water is clear.

Turn OFF the shutoff valve on the water pipe. Coil the copper

tubing.

Connect to Refrigerator

NOTE: On kit models, assemble water valve to refrigerator per kit

instructions.

Style 1

1. Unplug refrigerator or disconnect power.

2. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown. Tighten the compression nut. Do not

overtighten.

3. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

A. Tube clamp

B. Copper tubing

C. Compression nut

D. Valve inlet

The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Style 2

1. Unplug refrigerator or disconnect power.

2. Disconnect the tube clamp on the back of the product and

insert the copper tubing through the clamp as shown.

3. Attach the copper tube to the valve inlet using a compression

nut and sleeve as shown.

4. Tighten the compression nut. Do not overtighten. Reattach the

tube clamp and tube to the back of the cabinet.

.... A

_ C

._,.O

A. Tube clamp C. Compression nut

B. Copper tubing

5. Turn shutoff valve ON. Check for leaks. Tighten any

connections (including connections at the valve) or nuts that

leak.

6. The ice maker is equipped with a built-in water strainer. If your

water conditions require a second water strainer, install it in

the 1/4"(6.35 mm) water line at either tube connection. Obtain

a water strainer from your nearest appliance dealer.

Complete the Installation

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord,

Failure to follow these instructions can result in death,

fire, or electrical shock.

Plug into a grounded 3 prong outlet.

NOTE: Allow 24 hours to produce the first batch of ice. Discard

the first three batches of ice produced. Allow 3 days to completely

fill ice container.

TOOLS NEEDED: %6" hex-head socket wrench, #2 Phillips

screwdriver, flat-blade screwdriver, %6" open-end wrench, flat

2" putty knife.

IMPORTANT:

• Before you begin, turn the refrigerator control OFR Unplug

refrigerator or disconnect power.

• Remove food and adjustable door or utility bins from doors.

• If you are only removing and replacing the doors, see the

"Remove Doors and Hinges" and "Replace Doors and

Hinges" sections.

• Depending on your model, you may have standard (Style 1) or

contoured (Style 2) doors. Ifyou are also going to reverse the

door swing, follow the instructions for the appropriate door

style.

Remove Doors and Hinges

5/16"Hex-Head Hinge Screw

1. Unplug refrigerator or disconnect power.

2. Close the refrigerator door and keep both doors closed until

you are ready to lift them free from the cabinet.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

3. Remove the parts for the top hinge as shown in Top Hinge

graphic. Lift the freezer door free from the cabinet.

4. Remove the parts for the center hinge as shown in the Center

Hinge graphic. Lift the refrigerator door free from the cabinet.

5. Remove the parts for the bottom hinge as shown in the

Bottom Hinge graphic.

Reverse Doors (optional)

IMPORTANT: If you want to reverse your doors so that they open

in the opposite direction, follow these steps. If you are not

reversing the doors, see "Replace Doors and Hinges."

Style I - Standard

Graphics follow these instructions.

Door StopScrew

Door HandleSealing Screw

Door Hinge Hole Plug

Cabinet Hinge Hole Plug

Flat-Head Handle Screw

Door Handle Seal Screw Front

Door HandleScrew Cover

Round-Head HandleScrew

Cabinet

1. Remove 5/16"hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from cabinet top and

move them to opposite side hinge holes as shown.

See Graphic 1-2.

Freezer door

1. Remove freezer handle assembly as shown. Keep all parts

together. See Graphic 2.

2. Remove door hinge hole plug. Move to opposite side as

shown. See Graphic 3.

3. Remove door handle sealing screws. Move to opposite side of

freezer door as shown. See Graphic 4.

4. Remove door stop. Move to opposite side of freezer door as

shown. See Graphic 5.

5. Position freezer handle on opposite side of freezer door.

Assemble handle on door as shown. See Graphic 2.

6. Tighten all screws. Set aside door until hinges and refrigerator

compartment door are in place.

Refrigerator door

f. Remove the screw cover. See Graphic 6.

2. Remove refrigerator handle assembly as shown. Keep all

parts together. See Graphic 6.

3. Remove door hinge hole plug from refrigerator door. Move to

opposite side hinge hole as shown. See Graphic 3.

4. Remove door handle sealing screws. Move to opposite side of

refrigerator door as shown. See Graphic 4.

5. Remove door handle seal screw front. Move to opposite side

of refrigerator door as shown. See Graphic 7.

6. Remove door stop. Move to opposite side of refrigerator door

as shown. See Graphic 5.

7. Position refrigerator handle on opposite side of the refrigerator

door as shown. See Graphic 6. Drive top two screws in handle

first. Align lower portion of handle and drive bottom screw.

8. Replace screw cover. See Graphic 6.

9. Tighten all screws. Set aside refrigerator door until bottom

hinge is installed on refrigerator.

Style 2 - Contoured

Graphics follow these instructions.

Round-Head Door Handle

Handle Screw Screw Hole Plug

Door Hinge

Hole Plug

Cabinet

1. Remove 5/16"hex-head hinge screws from handle side and

move them to opposite side. See Graphic 1-1.

2. Remove cabinet hinge hole plugs from the cabinet top and

move them to opposite side hinge holes as shown. See

Graphic 1-2.

Doors

1. Remove door hinge hole plug from top of freezer door. Move

to opposite side as shown. See Graphic 2.

2. Remove door stop from both the freezer and refrigerator

doors and move to the other side. See Graphic 3.

Replace Doors and Hinges

NOTE: Graphic may be reversed if door swing is reversed.

1. Replace the parts for the bottom hinge as shown. Tighten

screws. Replace the refrigerator door.

NOTE: Provide additional support for the doors while the

hinges are being moved. Do not depend on the door magnets

to hold the doors in place while you are working.

2. Assemble the parts for the center hinge as shown and tighten

all screws. See Center Hinge graphic. Replace the freezer

door.

3. Assemble the parts for the top hinge as shown. See Top Hinge

graphic. Do not tighten screws completely.

4. Line up the doors so that the bottom of the freezer door aligns

evenly with the top of the refrigerator door. Tighten all screws.

Final Steps

1. Check all holes to make sure that hole plugs and screws are in

place. Reinstall top hinge cover. See Top Hinge graphic.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

2. Plug in refrigerator or reconnect power.

3. Reset the controls. See "Using the Controls."

4. Return all removable door parts to doors and food to

refrigerator.

Style I - Standard

Top Hinge

A. 5/_8"Hex-Head Hinge Screws

B. Top Hinge

C. Spacer

Center Hinge

A. Door Stop

B. Door Stop Screw

C. Spacer

D. Center Hinge

E. 5/_6"Hex-Head Hinge Screws

F, Spacer

Bottom Hinge

A. Door Stop

B. Spacer

C. Door Stop Screw

D. Bottom Hinge

E. 5/_6"Hex-Head Hinge Screws

A................._i__ °_l

A. Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

A. Flat-Head Handle Screws

B. Freezer Handle

I\_ "- "i_\1

A. Door Handle Sealing Screws

Front View Side View []

.L, I

A. Door Stop Screw A B

B. Door Step

A. Door Handle

Seal Screw Front

Style 2 - Contoured

Top Hinge

A. Top Hinge Cover

B. 946"Hex-Head Hinge Screws

C. Top Hinge

D. Spacer

Center Hinge

A. Door Stop

B. Door Stop Screw

C. Spacer

D. Center Hinge

E, 5/_8"Hex-Head Hinge Screws

F. Spacer

Bottom Hinge

A. Doer Stop

B. Spacer

C. Door Step Screw

D. Bottom Hinge

E. s/_8"Hex-Head Hinge Screws

OtO,r_ 0

| "w'l..................................A

A. 5/_,, Hex-Head Hinge

Screws and Washers

A. Cabinet Hinge Hole Plugs

A. Door Hinge Hole Plug

Removal of Door Stops

A. Door Stop

B. Door Stop Screw

Reinstallation of Door Stops

A.Door Stop

B, DoorStop Screw

Your refrigerator has two front adjustable rollers - one on the right

and one on the left. Ifyour refrigerator seems unsteady or you

want the doors to close easier, adjust the refrigerator's tilt using

the instructions below.

Depending on your model, your refrigerator may have leveling

legs (Style 1) or leveling screws (Style 2). They are part of the front

roller assemblies which are found at the base of the refrigerator on

either side.

1. Turn the leveling legs or leveling screws to the right to raise

that side of the refrigerator or to the left to lower that side. It

may take several turns to adjust the tilt of the refrigerator.

NOTE: Having someone push against the top of the

refrigerator takes some weight off the leveling screws and

rollers. This makes it easier to adjust the screws.

2. Open both doors again and be sure that they close as easily

as you like. If not, tilt the refrigerator slightly more to the rear

by turning both leveling screws to the right. It may take several

more turns, and you should turn both leveling screws the

same amount.

Style I

Style 2

3. Using a level, be sure that the refrigerator is still level side to

side. Readjust if necessary.

REFRIGERATORUSE

The temperature control is located at the top of the refrigerator

compartment. It controls the temperature in both the refrigerator

and freezer compartments.

For your convenience, the Temperature Control is preset at the

factory. When you first install your refrigerator, make sure that the

control is still preset to the mid-setting as shown.

NOTE: To turn your refrigerator off, turn the refrigerator control to

the word OFF or until the word OFF appears. Your product will not

cool when the refrigerator control is set to OFE

1 3 normal

coldest

IMPORTANT:

• Give your refrigerator time to cool down completely before

adding food. It is best to wait 24 hours before you put food

into the refrigerator.

• If you add food before the refrigerator has cooled completely,

your food may spoil. Adjusting the Refrigerator and Freezer

Controls to a higher (colder) than recommended setting will

not cool the compartments any faster.

Adjusting Controls

The mid-setting indicated in the previous section should be

correct for normal household usage. The controls are set correctly

when milk or juice is as cold as you like and when ice cream is

firm.

If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not blocked.

If you need to adjust temperatures, use the settings listed in the

chart below as a guide. Wait at least 24 hours between

adjustments and then recheck the temperatures.

CONDITION/REASON: ADJUSTMENT:

REFRIGERATOR section too warm Adjust REFRIGERATOR

- Door opened often, large amount or TEMPERATURE

of food added or room Control one setting

temperature very warm higher

FREEZER section too warm/ice not

made fast enough

- Door opened often, or large

amount of food added or very cold

room temperature (can't cycle

often enough)

- Heavy ice usage

REFRIGERATOR section too cold

- Controls not set correctly for your

conditions

Adjust FREEZER or

TEMPERATURE Control

one setting higher

Adjust REFRIGERATOR

or TEMPERATURE

Control one setting

lower

FREEZER section too cold Adjust FREEZER or

- Controls not set correctly for your TEMPERATURE Control

conditions one setting lower

Turning the Ice Maker On/Off

To turn the ice maker ON, simply lower the wire shutoff arm.

To manually turn the ice maker OFF,lift the wire shutoff arm to the

OFF (arm up) position and listen for the click.

NOTE: Your ice maker has an automatic shutoff. As ice is made,

the ice cubes will fill the ice storage bin and the ice cubes will

raise the wire shutoff arm to the OFF (arm up) position. Do not

force the wire shutoff arm up or down.

Ice Production Rate

• Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

• The ice maker should produce approximately 8 to 12 batches

of ice in a 24-hour period.

• To increase ice production, lower the freezer and refrigerator

temperature. See "Using the Controls." Wait 24 hours

between adjustments.

• For maximum ice production (on some models), push the

switch to ICE PLUS. The ice maker should produce 16 to

20 batches of ice in a 24-hour period in the Ice Plus mode.

Remember

• The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If asoftened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

• Do not use anything sharp to break up the ice in the bin. This

can cause damage to the ice container and the dispenser

mechanism.

• Do not store anything on top of or in the ice maker or ice bin.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to keep odors

from building up. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

To Clean Your Refrigerator:

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools.

1. Unplug refrigerator or disconnect power.

2. Hand wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash painted metal exteriors with a clean sponge or soft cloth

and a mild detergent in warm water. Dry thoroughly with a soft

cloth.

4. Plug in refrigerator or reconnect power.

....... _j !_J

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to

replace the bulb with one of the same size, shape, and wattage.

1. Unplug refrigerator or disconnect power.

2. Reach behind the control panel and unscrew the bulb.

3. Replace the bulb with a 40-watt appliance bulb.

4. Plug in refrigerator or reconnect power.

TROUBLESHOOTING

Trythe solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

• Power cord unplugged? Plug into a grounded 3 prong outlet.

• Is outlet working? Plug in a lamp to see if the outlet is

working.

• Household fuse blown or circuit breaker tripped? Replace

the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

Are controls on? Make sure the refrigerator controls are on.

See "Using the Controls."

New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting

will not cool either compartment more quickly.

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its

high-efficiency compressor and fans. The unit may run even

longer if the room is warm, a large food load is added, doors are

opened often, or if the doors have been left open.

The refrigerator seems noisy

Refrigerator noise has been reduced over the years. Due to this

reduction, you may hear intermittent noises from your new

refrigerator that you did not notice from your old model. Below are

listed some normal sounds with explanations.

• Buzzing - heard when the water valve opens to fill the ice

maker.

• Pulsating - fans/compressor adjusting to optimize

performance.

• Hissing/Rattling - flow of refrigerant, movement of water

lines, or from items placed on top of the refrigerator.

• Sizzling/Gurgling - water dripping on the heater during

defrost cycle.

• Popping - contraction/expansion of inside walls, especially

during initial cool-down.

• Water running - may be heard when water melts during the

defrost cycle and runs into the drain pan.

• Creaking/Cracking - occurs as ice is being ejected from the

ice maker mold.

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct

position.

• Crisper cover in the way? Make sure the crisper cover is

pushed in fully, so that the back rests on the supports.

The doors are difficult to open

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

• Gaskets dirty or sticky? Clean gaskets and contact surfaces

with mild soap and warm water. Rinse and dry with soft cloth.

The lights do not work

• Is a light bulb loose in the socket or burned out? See

"Changing the Light Bulbs."

Temperature is too warm

• New installation? Allow 24 hours following installation for the

refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for

refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?

Adjust the controls a setting colder. Check temperature in

24 hours. See "Using the Controls."

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s} opened often or left open? Allows humid air to enter

refrigerator. Minimize door openings and keep doors fully

closed.

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply

shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch

(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation

for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for

ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?

Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

The ice cubes are hollow or small

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff

valve fully open.

• Kink in the water source line? A kink in the line can reduce

water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to

your cold water supply? This can decrease water pressure.

See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a

licensed, qualified plumber.

Off-taste, odor or gray color in the ice

• New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.

• Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.

• Odor transfer from food? Use airtight, moisture proof

packaging to store food.

• Are there minerals (such as sulfur) in the water?. A water

filter may need to be installed to remove the minerals.

WHIRLPOOLCORPORATION MAJOR APPLIANCE WARRANTY

ONE YEAR LIMITED WARRANTY

For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for FSP_replacement parts

and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.

ITEMS WHIRLPOOL WILL NOT PAY FOR

1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair

house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty

coverage.

3. Repairs when your major appliance is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in

accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.

5. Any food loss due to refrigerator or freezer product failures.

6. Replacement parts or repair labor costs for units operated outside the United States or Canada.

7. Pickup and delivery. This major appliance is designed to be repaired in the home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

g. Expenses for travel and transportation for product service in remote locations.

10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with

published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED

HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,

ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATETO STATE OR PROVINCE

TO PROVINCE.

Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if

another warranty applies.

If you need service, first see the "Troubleshooting" section of the Use & Care Guide. After checking "Troubleshooting," additional help

can be found by checking the "Assistance or Service" section or by calling Whirlpool. Inthe U.S.A., call 1-800-253-1301. In Canada,

call 1-800-807-6777. 8/o5

MANUAL DE USO Y CUIDADO DELREFRIGERADOR

Ayuda o Servicio T( cnico

Si necesita ayuda o servicio tecnico, yea primero la secci6n

"Soluci6n de Problemas". Para obtener asistencia adicional

Ilamenos al 1-800-253-1301 desde cualquier lugar de los EE.UU.,

o escriba a:

Estate Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Tambien puede obtener informaci6n visitando nuestro sitio web

en www.roperappliances.com.

Favor de incluir un n_mero telef6nico de dia en su

correspondencia.

Guarde este libro y su comprobante de compra juntos para

referencia futura. Usted debera proporcionar evidencia de la

compra o una fecha de instalacibn para obtener servicio bajo

la garantia.

Escriba la siguiente informaci6n acerca de su electrodomestico

para ayudarle a obtener asistencia o servicio tecnico si alguna vez

Ilegara a necesitarlo. Debera tenet a mano el nOmero completo

del modelo y de la serie. Puede encontrar esta informaci6n en la

etiqueta con el nOmero de modelo y de serie que esta ubicada en

la pared interior del compartimiento del refrigerador.

Nombre del distribuidor

Numero de serie

Direcci6n

Numero de tel_fono

Numero del modelo

Fecha de compra

SEGURIDAD DELREFRIGERADOR

Su seguridad y la seguridad de los demas es muy importante.

Hemos incluido muchos mensajes importantes de seguridad en este manual yen su electrodomestico. Lea y obedezca siempre

todos los mensajes de seguridad.

Este es el sfmbolo de advertencia de seguridad.

Este simbolo le llama la atenci6n sobre peligros potenciales que pueden ocasionar la muerte o una lesi6n a

usted y a los demas.

Todos los mensajes de seguridad iran a continuaci6n del simbolo de advertencia de seguridad y de la palabra

"PELIGRO" o "ADVERTENCIA". Estas palabras significan:

Si no sigue las instrucciones de inmediato, usted puede

morir o sufrir una lesion grave.

Si no sigue las instrucciones, usted puede morir o sufrir

una lesion grave.

Todos los mensajes de seguridad le diran el peligro potencial, le diran c6mo reducir las posibilidades de sufrir una lesi6n y Io que

puede suceder si no se siguen las instrucciones.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA: Para reducir el riesgo de incendio, cheque electrico, o lesiones personales al usar su refrigerador siga

estas precauciones basicas, incluidas las siguientes:

[] Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

[] No quite la terminal de conexi6n a tierra.

[] No use un adaptador.

[] No use un cable electrico de extensi6n.

[] Desconecte el suministro de energia antes de darle servicio.

[] Vuelva a colocar todos los componentes y paneles antes de

hacerlo funcionar.

[] Remueva las puertas de su refrigerador viejo.

[] Use un limpiador no inflamable.

[] Mantenga los materiales y vapores inflamables, tales como

gasolina, alejados del refrigerador.

[] Use dos o mas personas para mover e instalar el

refrigerador.

[] Desconecte el suministro de energia antes de instalar la

fabrica de hielo (en aquellos modelos que incluyen el juego

de instalaci6n de la fabrica de hielo).

CONSERVAR ESTAS INSTRUCCIONES

C6mo deshacerse adecuadamente de

surefrigerador viejo

Antes de tirar su viejo refrigerador o congelador:

• Saquelas puertas.

• Deje los estantes en su lugar para que los ni_os no puedan

meterse con facilidad.

Peligro de Asfixia

Remueva las puertas de su refrigerador viejo.

No seguir esta instrucci6n puede ocasionar la muerte

o da_o al cerebro.

IMPORTANTE: El atrapamiento y asfixia de ni_os no es un

problema del pasado. Los refrigeradores tirados y abandonados

son un peligro, aOn si van a quedar ahi "por unos pocos dias". Si

Ud. esta por deshacerse de su refrigerador viejo, per favor siga

las instrucciones que se dan a continuaci6n para evitar

accidentes.

INSTRUCCIONESDE INSTALACION

Peligro de Peso Excesivo

Use dos o m_s personas para mover e instalar

el refrigerador.

No seguir esta instrucci6n puede ocasionar una

lesion en la espalda u otro tipo de lesiones.

Quitar los materiales de empaque

No use instrumentos filosos, alcohol para fricciones, Ifquidos

inflamables, o productos de limpieza abrasives para eliminar los

restos de cinta o goma. Estos productos pueden da_ar la

superficie de su refrigerador. Para mas informaci6n, vea la

secci6n "Seguridad del refrigerador".

IMPORTANTE: No quite el inserto de espuma blanca de

devoluci6n de aire que esta ubicado detras del panel de control

en el techo del refrigerador. Si se quita el inserto, el hielo puede

bajar del congelador y hacer que se formen gotas de hielo.

Como mover su refrigerador:

Su refrigerador es muy pesado. Cuando mueva su

refrigerador para limpiarlo o darle servicio, proteja el piso.

AI mover el refrigerador, siempre tire directamente hacia

afuera. No menee el refrigerador de lado a lado ni Io haga

"caminar" cuando Io trate de mover ya que podrfa da_ar

el piso.

Limpiar su refrigerador antes de usarlo

Una vez que usted haya quitado todos los materiales de

empaque, limpie el interior de su refrigerador antes de usarlo. Vea

las instrucciones de limpieza en la secci6n "Cuidado de su

refrigerador".

Informacion importante para saber acerca de los estantes

y tapas de vidrio:

No limpie los estantes y tapas de vidrio con agua caliente

mientras estan frfos. Los estantes y tapas pueden romperse

si se exponen a cambios bruscos de temperatura o impacto,

como serfa un golpe brusco. Para su protecci6n, el vidrio

templado se ha dise_ado para hacerse a_icos. Esto es normal.

Los estantes y tapas de vidrio son muy pesados. Tenga

mucho cuidado al sacarlos para evitar que se da_en al caer.

Peligro de Explosi6n

IV]antenga los materiales y vapores infiamables,

tales como gasolina, alejados del refrigerador.

No seguir esta instruccion puede ocasionar la muerte,

exploei6n, o incendio.

Para asegurar la ventilaci6n adecuada de su refrigerador, deje un

espacio de W' (12,70 mm) a cada lado. Deje un espacio de

3" (7,5 cm) de espacio entre los gabinetes de arriba y la parte

superior del refrigerador. Deje por Io menos 1" (25,40 mm) entre la

parte trasera del gabinete y la pared. Si su refrigerador tiene una

fabrica de hielo, asegQrese de que haya espacio adicional atras

para la conexi6n de las tuberias de agua.

• Siva a instalar su refrigerador al costado de una pared fija,

deje como minimo 2" (5,08 cm) en el lado de la bisagra (segOn

el modelo) para permitir que la puerta se abra bien.

• Nivele el refrigerador. Vea "Ajuste las puertas".

NOTA: No se recomienda instalar el refrigerador cerca de un

homo, radiador u otra fuente de calor, ni en un lugar donde la

temperatura Ilegue debajo de 55°F (13°C).

I I

II I

Jl I

Peligro de Choque Eiectrico

Conecte a un contacto de pared de conexion a tierra de

3 terminaleso

No quite la terminal de conexion a tierra.

No use un adaptador.

No use un cable electrico de extensi6no

No seguir estas instrucciones puede ocaeionar

la muerte, incendio o choque electrico.

Antes de mover el refrigerador a su ubicaci6n final, es importante

asegurarse de que tiene la conexi6n electrica adecuada.

M_todo de conexibn a tierra recomendado

Se requiere una fuente de energia electrica de 115 Voltios, 60 Hz.,

CA solamente y con fusibles de 15 6 20 amperios, debidamente

conectada a tierra. Se recomienda que use un circuito separado

s61opara su refrigerador. Use un tomacorriente que no se pueda

apagar con un interruptor. No use un cable electrico de extensi6n.

NOTA: Antes de realizar cualquier tipo de instalaci6n, limpieza o

de quitar un foco de luz, ponga el control (del termostato, del

refrigerador o del congelador dependiendo del modelo) en la

posici6n OFF (Apagado) y luego desconecte el refrigerador de la

fuente de energfa. Cuando haya terminado, reconecte el

refrigerador a la fuente de energia electrica y vuelva a poner el

control (del termostato, del refrigerador o del congelador

dependiendo del modelo) en la posici6n deseada.

u stos de sls;} * .

Reena las herramientas y piezas necesarias antes de comenzar la

instalaci6n. Lea y siga las instrucciones provistas con cualquiera

de las herramientas enlistadas aquL

IMPORTANTE:

• Si usa el refrigerador antes de instalar la conexi6n del agua,

ponga la fabrica de hielo en la posici6n OFF (apagado).

• Todas las instalaciones deben hacerse de acuerdo a los

requerimientos locales de plomerfa.

• Use tuberias de cobre y revise si hay fugas. Instale tuberia de

cobre s61oen Areas donde la temperatura va a permanecer

por encima del punto de congelaci6n.

HERRAMIENTAS REQUERIDAS: Destornillador de hoja plana,

Ilaves de boca de %d' y _A"o 2 Ilaves ajustables, Ilave para tuercas

y broca de barrena de _/4",taladro manual o electrico

(debidamente conectado a tierra).

NOTA: El distribuidor de su refrigerador tiene un juego con una

valvula de cierre tipo montura de 1/4"(6,35 mm), una uni6n y

tuberia de cobre. Antes de comprar, asegQrese que la valvula tipo

montura cumpla con los c6digos de plomeria de su Iocalidad. No

use una valvula perforadora o una valvula de montura de ¾d'

(4,76 mm) que reduce el flujo de agua y se obstruye con mas

facilidad.

Presibn del agua

Se necesita un suministro de agua fria con presi6n de agua entre

30 y 120 Ibs/pulg 2(207 a 827 kPa) para hacer funcionar la fabrica

de hielo. Si usted tiene preguntas acerca de la presi6n de agua,

Ilame a un plomero competente autorizado.

Suministro de agua de 6smosis inversa

IMPORTANTE: La presi6n del suministro de agua que sale de un

sistema de 6smosis inversa y va a la valvula de entrada de agua

del refrigerador necesitara ser entre 30 y 120 Ibs/pulg 2(207 a

827 kPa).

Si se conecta un sistema de filtraci6n de agua de 6smosis inversa

al suministro de agua fria, la presi6n de agua al sistema necesitara

ser de un minimo de 40 a 60 Ibs/pulg 2(276 a 414 kPa).

Si la presi6n del agua del sistema de 6smosis inversa es menor de

40 a 60 Ibs/pulg 2(276 a 414 kPa):

• F[jese si el filtro de sedimentos en el sistema de 6smosis

inversa esta bloqueado y reemplacelo si fuera necesario.

• Deje que se vuelva a Ilenar el tanque de almacenaje del

sistema de 6smosis inversa despues del uso intenso.

Si tiene preguntas acerca de la presi6n del agua, Ilame a un

plomero competente autorizado.

Lea todas las instrucciones antes de comenzar.

IMPORTANTE: Si usa el refrigerador antes de instalar la conexi6n

del agua, ponga la fabrica de hielo en la posici6n de apagado

(OFF).

Conexibn a la tuberia de agua

1. Desenchufe el refrigerador o desconecte el suministro de

energia.

2. CIERRE el suministro principal del agua. ABRA el grifo de

agua mas cercano el tiempo suficiente para que la tuberia de

agua se despeje totalmente.

Ubique una tuberia vertical de agua frfa de 1/2"a 11/4"(1,27 cm

a 3,18 cm) cercana al refrigerador.

IMPORTANTE:

• AsegOrese de que sea una tuberfa de agua frfa,

• Una tuberfa horizontal funcionar& pero taladre per el lado

de arriba de la tuberfa, no per debajo. Esto ayudara a

mantener el agua alejada del taladro. Esto tambien evita

que se junte sedimento normal en la valvula.

Para determinar la Iongitud de la tuberfa de cobre que va a

necesitar, mida desde la conexi6n baja de la parte trasera

izquierda del refrigerador hasta la tuberfa de agua. Agregue

7 pies (2,1 m) para la limpieza. Use tuberia de cobre de

1/4"(6,35 mm) de diametro externo. AsegOrese que ambos

extremes de la tuberfa de cobre esten cortados rectos.

Usando un taladro conectado a tierra, per[ore un orificio de

1/4"en la tuberfa de agua frfa que usted ha elegido,

A. Tuberfa de agua frfa

B. Abrazadera para tuberfa

C. Tuberfa de cobre

D. Tuerca de compresidn

E.Manga de compresidn

F. V#lvula de cierre

G. Tuerca de presidn

6. Ajuste la vMvula de cierre a la tuberia de agua fria con la

abrazadera para tuberia. AsegQrese que el extremo de salida

este firmemente insertado en el orificio taladrado de 1/4"en la

tuberia de agua y que la arandela este por debajo de la

abrazadera para tuberia. Ajuste la tuerca de presidn. Apriete

los tornillos de la abrazadera para tuberia lentamente yen

forma pareja de manera que la arandela provea un cierre

hermetico, No apriete demasiado porque se puede quebrar la

tuberia de cobre.

7. Deslice la manga de compresidn y la tuerca de compresidn

sobre la tuberia de cobre como se muestra. Inserte el extremo

de la tuberia en el extremo de salida hasta donde sea posible.

Atornille la tuerca de compresi6n sobre el extremo de salida

con una Ilave ajustable. No apriete demasiado.

8. Coloque el extreme libre de la tuberfa dentro de un recipiente

o fregadero, y ABRA la Ilave de agua principal para lavar la

tuberia hasta que el agua salga limpia. CIERRE la valvula de

cierre del agua en la tuberia de agua. Enrolle la tuberia de

cobre en espiral.

Conexibn al refrigerador

NOTA: En modelos que vienen con juegos, monte la valvula del

agua al refrigerador de acuerdo alas instrucciones que vienen

con los juegos.

Estilo 1

1. Desenchufe el refrigerador o desconecte el suministro de

energfa.

2. Fije el tubo de cobre a la entrada de la vMvula usando una

tuerca de compresi6n y manga de compresi6n como se

muestra, Ajuste la tuerca de compresidn. No apriete

demasiado,

3. Use la abrazadera para tuberfa en la parte trasera del

refrigerador para afianzar la tuberia al refrigerador segQn se

muestra. Esto ayudara a evitar da_os a la tuberfa cuando el

refrigerador se empuje contra la pared posterior.

4. ABRA la vMvula de cierre,

5. Revise si hay fugas. Ajuste las conexiones (incluso las de la

valvula) o tuercas que tienen fugas,

A. Abrazadera para tuberfa C. Tuerca de compresidn

B. Tuberfa de cobre D. Entrada de la vblvula

La fabrica de hielo esta equipada con un filtro de agua

incorporado. Si las condiciones del agua local requieren un

segundo filtro de agua, se debe instalar en la linea de agua de

1/4"(6,35 mm) en cualquiera de las conexiones de la tuberfa.

Consiga un filtro de agua del distribuidor de

electrodomesticos mas cercano a su domicilio,

Estilo 2

1. Desenchufe el refrigerador o desconecte el suministro de

energia.

2. Desconecte la abrazadera para sujetar tubes que esta en la

parte posterior del producto e inserte la tuberfa de cobre a

traves de la abrazadera come se ilustra.

3. Sujete la tuberia de cobre a la entrada de la vMvula usando

una tuerca de compresi6n y una manga de compresi6n segQn

se ilustra,

4. Ajuste la tuerca de compresi6n, No la ajuste demasiado.

Vuelva a unir la abrazadera para sujetar tubos con la tuberfa a

la parte posterior del gabinete.

a A

-J 1

ic==_ c==_ ............ C

'==

A. Abrazadera para tuberfa C. Tuerca de compresidn

B. Tuberfa de cobre

Abra la vMvula de paso. Revise si hay perdidas. Ajuste todas

las conexiones (incluso la conexiones de la vMvula) 0 las

tuercas que tengan perdidas.

La fabrica de hielo esta equipada con un filtro de agua

incorporado. Si las condiciones del agua local requieren un

segundo filtro de agua, se debe instalar en la linea de agua de

1/4"(6,35 mm) en cualquiera de las conexiones de la tuberfa.

Consiga un filtro de agua del distribuidor de

electrodomesticos mas cercano a su domicilio,

Cbmo terminar la instalacibn Cbmo quitar las puertas y las bisagras

Peligro de Cheque Electrico

Cenecte a un contacto de pared de cenexion a tierra de

3 terminales.

No quite la terminal de conexion a tierra.

No use un adaptader.

No use un cable electrico de extensi6n.

No seguir estas instrucciones puede ocaeionar

la muerte, incendio e cheque electrice.

Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

NOTA: Deje transcurrir 24 horas para la producci6n de la primera

tanda de hielo. Deshagase de los tres primeros Iotes de hielo

producido. Deje pasar 3 dias para que se Ilene completamente el

recipiente para hielo.

HERRAMIENTAS NECESARIAS: Ilave tubular de cabeza

hexagonal de %6", destornillador Phillips No. 2, destornillador de

cabeza plana, Ilave ajustable de %6%cuchillo plane para masilla

de 2".

IMPORTANTE:

• Antes de comenzar, gire el control del refrigerador hacia la

posici6n de apagado (OFF). Desenchufe el refrigerador o

desconecte el suministro de energia,

• Quite los alimentos y la puerta ajustable o los recipientes de

use m@tiple de las puertas,

• Si usted s61o va a quitar las puertas y volverlas a colocar, vea

las secciones "C6mo quitar las puertas y las bisagras" y

"C6mo velvet a poner las puertas y las bisagras en su lugar".

• Dependiendo de su modelo, puede set que usted tenga

puertas estandar (Estilo 1) o contorneadas (Estilo 2). Si usted

tambien va a invertir el sentido de oscilaci6n de la puerta, siga

las instrucciones para el estilo de puerta adecuado,

Tornillo de cabeza hexagonal para bisagra de 5/16"

1. Desenchufe el refrigerador o desconecte el suministro de

energfa.

2. Cierre la puerta del refrigerador y mantenga las dos puertas

cerradas hasta que este listo para separarlas del gabinete.

NOTA: Mientras quita las bisagras siempre disponga de un

soporte adicional para las puertas. No se confie en que los

imanes de las puertas van a sostener las puertas mientras

trabaja.

3. Quite los componentes de la bisagra superior come se

muestra en la ilustracidn de la bisagra superior. Levante y

quite la puerta del congelador del gabinete,

4. Quite los componentes de la bisagra central come se muestra

en la ilustraci6n de la bisagra central. Levante y quite la puerta

del refrigerador del gabinete,

5. Quite los componentes de la bisagra inferior come se muestra

en la ilustracidn de la bisagra inferior.

Cambio del sentido de apertura de las puertas (opcional)

IMPORTANTE: Siga estas instrucciones si desea que las puertas

abran en el sentido opuesto, Si no desea cambiar el sentido de

apertura de las puertas, vea "Crime volver a colocar las puertas y

las bisagras".

Estilo I - Estandar

Lasilustraciones aparecendespues de estas instrucciones.

Tomillo del reten

de la puerta

Tomillo sellador

de la manija de la puerta

Tomillo de cabeza

plana de la manija

Tomillo sellador frontal

de la manija de la puerta

Gabinete

Tapdn del orificio

de la bisagra de la puerta

Tapdn del orificio

de la bisagra del gabinete

Tapa del tomillo de

la manija de la puerta

Tomillo de cabeza

redonda de la manija

Quite los tornillos de cabeza hexagonal de 5_6"de la bisagra

del lade de la manija y col6quelos del lade opuesto, Vea la

ilustraci6n 1-1.

Quite los tapones de los orificios de las bisagras de la parte

superior del gabinete y col6quelos en los orificios de la

bisagra del lade opuesto come se indica. Vea la

ilustraci6n 1-2.

Puerta del congelador

1. Quite la ensambladura de la manija del congelador como se

indica. Conserve juntos todos los componentes. Vea

la ilustraci6n 2.

2. Quite el tap6n del orificio de la bisagra de la puerta. Col6quelo

del lado opuesto como se indica. Vea la ilustraci6n 3.

3. Quite los tomillos selladores de la manija de la puerta.

Col6quelos del lado opuesto de la puerta del congelador

como se indica. Vea la ilustraci6n 4.

4. Quite el reten de la puerta. Col6quelo del lado opuesto de la

puerta del congelador como se indica. Vea la ilustraci6n 5.

5. Coloque la manija del congelador del lado opuesto de la

puerta del congelador. Instale la manija en la puerta como se

indica. Vea la ilustraci6n 2,

6. Apriete todos los tomillos. Ponga la puerta a un lado hasta

que las bisagras y la puerta del compartimiento del

refrigerador esten en su sitio,

Puerta del refrigerador

1. Quite la cubierta del tornillo. Yea la ilustraci6n 6.

2. Quite la ensambladura de la manija del refrigerador come se

indica. Conserve juntos todos los componentes. Vea la

ilustraci6n 6.

3. Quite el tap6n del orificio de la bisagra de la puerta del

refrigerador. Col6quelo en el orificio de la bisagra del lado

opuesto come se indica. Vea la ilustraci6n 3,

4. Quite los tornillos selladores de la manija de la puerta.

Col6quelos del lado opuesto de la puerta del refrigerador

como se indica. Vea la ilustraci6n 4.

5. Quite el tap6n de enfrente del tornillo sellador de la manija de

la puerta. Col6quelo del lado opuesto de la puerta del

refrigerador como se indica. Vea la ilustraci6n 7.

6. Quite el reten de la puerta. Col6quelo del lado opuesto de la

puerta del refrigerador como se indica, Vea la ilustraci6n 5.

7. Coloque la manija del refrigerador del lado opuesto de la

puerta del refrigerador como se indica, Vea la ilustraci6n 6.

Enrosque primero los dos tornillos superiores de la manija.

Alinee la parte de abajo de la manija y enrosque el tornillo de

abajo,

8. Vuelva a colocar la cubierta del tornillo. Vea la ilustraci6n 6.

9. Apriete todos los tomillos. Ponga la puerta del refrigerador a

un lado hasta que se haya instalado la bisagra inferior en el

refrigerador.

Estilo 2 - Contorneada

Lasilustraciones aparecendespues de estas instrucciones,

Tornillo de Tapdndel orificio Tapdndel orifido

cabeza redonda del tomillo de la manija de la bisagra

de lamanija de lapuerta de la puerta

Gabinete

1. Quite los tornillos de cabeza hexagonal de %6" de la bisagra

del lado de la manija y col6quelos del lado opuesto, Vea la

ilustraci6n 1-1,

2. Quite los tapones de los orificios de las bisagras de la parte

superior del gabinete y col6quelos en los orificios de la

bisagra del lado opuesto. Vea la ilustraci6n 1-2.

Puertas

1. Quite eltap6n del orificio de la bisagra de la parte superior de

la puerta del congelador. Col6quelo del lado opuesto come se

indica, Vea la ilustraci6n 2.

2. Quite el reten de la puerta del congelador y del refrigerador y

p6ngalos en el lade opuesto. Vea la ilustraci6n 3.

Cbmo volver a poner en su lugar las puertas y las

bisagras

NOTA: Si el sentido de apertura de la puerta se cambia, la imagen

de la puerta pudiera quedar invertida,

1. Vuelva a poner los componentes de la bisagra inferior en su

sitio como se indica, Apriete los tornillos. Vuelva a poner en su

lugar la puerta del refrigerador.

NOTA: Mientras quita las bisagras siempre disponga de un

soporte adicional para las puertas. No se confie en que los

imanes de las puertas van a sostener las puertas mientras

trabaja.

2. Arme los componentes de la bisagra central como se indica y

apriete todos los tornillos. Vea la ilustraci6n de la bisagra

central. Vuelva a poner en su lugar la puerta del congelador.

3. Ensamble las piezas de la bisagra superior como se indica.

Vea la ilustraci6n de la bisagra superior. No atornille

completamente los tornillos.

4. Alinee las puertas de tal manera que la parte inferior de la

puerta del congelador este alineada uniformemente con la

parte superior de la puerta del refrigerador. Apriete todos los

tornillos.

Pasos finales

1. Revise todos los orificios para cerciorarse que los tapones de

los orificios y los tornillos esten en su lugar. Vuelva a instalar la

cubierta de la bisagra superior. Vea la ilustraci6n de la bisagra

superior.

Peligro de Choque Electrico

Conecte a un contacto de pared de conexi6n a tierra de

3 terminales.

No quite la terminal de conexibn a tierra.

No use un adaptador.

No use un cable el6ctrico de extension.

No seguir estas instrucciones puede ocaeionar

la muerte, incendio o choque electrico.

2. Enchufe el refrigerador o reconecte el suministro de energfa.

3. Vuelva a ajustar los controles. Vea "Use de los controles".

4. Regrese todas las partes amovibles a las puertas y la comida

al refrigerador.

Estilo I - Estandar

Bisagra superior

Bisagra central

C .................

[

A. Reten de la puerta

B. Ternillo del reten de la puerta

C. Espaciador

D. Bisagra central

E. Tornilles de bisagra de cabeza

hexagonal de 5/_6"

F. Separador

Bisagra inferior

A. Reten de la puerta

B. Espaciador

C. Tornillo del reten de la puerta

D. Bisagra inferior

E. Ternillos de bisagra de cabeza

hexagonal de 5h6"

A. Tapon del orificio

de la bisagra de la puerta

A. Tomillos de cabeza plana

de la manija

B. Manija del congelador

'_======== _;...........

[_ =................................................................'*_:_\1

A. Tomi!los selladores

de la manija de la puerta

A. Temillo sellador frontal

de la manija de la puerta

Vista frontal Vista lateral

i , [ __

A B

A. Tornillo del reten de la puerta

B. Reten de la puerta

La page est en cours de chargement...

Estate T8RXNGFWD01 Manuel utilisateur

Marque: Estate

Modèle: T8RXNGFWD01

Catégorie: Frigos

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Estate T8RXNGFWD01 User manual
español: Estate T8RXNGFWD01 Manual de usuario

Estate T8RXNGFWD01 Manuel utilisateur

Estate T8RXNGFWD01 Manuel utilisateur

dans d''autres langues

Autres documents