Access Lighting 30111 Guide d'installation

Access Lighting
Marque
Access Lighting
Modèle
30111
Catégorie
Kits de montage
Taper
Guide d'installation
CERTIFICATION: cULus DRY NO. 30111
INSTALLATION INSTRUCTIONS
IMPORTANT
Before assembling your ACCESS LIGHTING fixture, please make
sure that you carefully read through this instruction sheet. Save this
instruction sheet and refer to it when additions to or changes in the
fixture configuration are made.
Enregistrer cette feuille d'instructions et de s'y référer lorsque les
ajouts ou changements dans la configuration de montage sont
faites
Consider having your fixture installed by a qualified licensed
electrician.
NOTE: The important safeguards and instructions that appear in
this manual are not meant to cover all possible conditions and
situations that may occur. It must be understood that common sense,
caution and care are factors that can’t be built into any product.
These factors must be supplied by the person(s) caring for and
operating the fixture
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and National Electrical Codes. These fixtures are intended for
mounting to standard 4” x 2 ½” metal octagon outlet box. The box
must be directly supported by the building structure and U.L
Recognized
STEP-BY-STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off
the Circuit Breaker or by removing the fuse at the fuse box. Just
turning the light off at the light switch is not sufficient to prevent
electrical shock.
APPLICATION
Wall & Celling
Fixture
MODEL NO.
30111
COLLECTION
Tahoe
PREPARE FIXTURE
If there is an existing fixture remove it.
Expose the supply wires from the outlet
box. Pull the supply wires through the
center hole in the fixture back plate.
Secure the fixture back plate to the
junction box with the supplied mounting
screws (1). Provide added support to the
fixture back plate by placing screws into
the two slotted holes on either end of the
fixture back plate
WHAT WE PROVIDE
Back Plate
Fixture Front Plate
Mounting
Hardware
Glass Diffuser
2 x 39W T5HO
Fluorescent Bulbs
1
1
Supply Wires from outlet box
Washers
Back Plate
Consult a qualified electrician to ensure correct branch
circuit conductor.
Consulter un electricien qualifie pour vous assurer
que les conducteurs de la derivation sont adequats
This product must be installed in accordance with the
applicable installation code by a person familiar with
the contstruction and operation of the product and the
hazards involved.
Ce produit doit etre installe selon le code d’installation
pertinent, par une personne qui connait bien le produit
et son fonctionnement ainsi que les risques inherents
WARNING: Risk of Fire and Electric Shock
CAUTION: Risque d’ Incendie et de Choc Electriques
CERTIFICATION: cULus DRY NO. 30111
CONNECT THE WIRES
Connect the black supply wire to the black fixture
wire. Secure with the supplied wire nuts. Connect
the white supply wires to the fixture wire. Secure
with the supplied wire nuts. Either wrap the outlet
box grounding (green) wire around the green
hexagonal screw provided on the mounting plate or
connect it to the supply ground wire provided with
the fixture. Secure all wires with U.L Certified
electrical tape (not supplied).
Tuck all wires carefully into the J-box.
2
MOUNT THE CANOPY
Secure the fixture front plate to the fixture back
plate by fitting the fixture front plate over the
fixture back plate and aligning the holes on the top
and bottom of both plates. Secure with the four
supplied screws (4).
Insert the supplied bulbs into the sockets.
Do not exceed the wattage stated on the warning label.
3
SECURE THE GLASS DIFFUSER
Secure the glass diffuser to the fixture front
plate by fitting on top of the fixture front
plate. Align the holes in the glass diffuser with
the screws protruding from the fixture front
plate. Fit the screws through the designated
holes. Secure with the supplied washer and
decorative screws (6).
4
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF
YOUR NEW ACCESS LIGHTING
FIXTURE
5
Screws
T5HO
bulbs
CAUTION
Please ensure that the fitting is cool and switched off
before replacing the bulb.DO NOT use bulbs that might
exceed the maximum wattage as stated on caution
label.
2
Fixture front plate
  • Page 1 1
  • Page 2 2

Access Lighting 30111 Guide d'installation

Access Lighting
Marque
Access Lighting
Modèle
30111
Catégorie
Kits de montage
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes