Hitachi WR14DL Manuel utilisateur

Cordless Impact Driver/Wrench

Akku-Schlagschrauber

Perceuse/visseuse à percussion sur batterie

Avvitatore a impulso a batteria per viti e bulloni

Snoerloze slagschroevendraaier/sleutel

Atornillador/Llave de impacto a batería

Aparafusadora/ Chave de impacto a bateria

¢Ú··ÓÔÎ·ÙÛ¿‚È‰Ô ª·Ù·Ú›·˜/∫ÏÂÈ‰›

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste istruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer

cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

807

Code No. C99141472

Printed in China

Hitachi Koki Co., Ltd.

1

4

3

87

1

2

8

7

6

WH12DAF2

Variable speed

WH 12DAF2

•

WR 12DAF2

WR12DAF2

H

E

C

I

E

C

F

G

1

2

1

3

2

5

4

〈UC14YFA〉

5

9

A

0

1

8

7

6

C

D

E

〈UC18YG〉

B

Representative office in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head office in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

31. 7. 2008

K. Kato

Board Director

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit

produkt conform de richtlijnen of gestandardiseerde

documenten EN60745, EN60335, EN55014 en EN61000

voldoet aan de eisen van EEG Bepalingen 2004/108/

EC, 2006/95/EC en 98/37/EC.

Deze verklaring is van toepassing op produkten

voorzien van de CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que

este producto está de acuerdo con las normas o con

los documentos de normalización EN60745, EN60335,

EN55014 y EN61000, según indican las Directrices del

Consejo 2004/108/CE, 2006/95/CE y 98/37/CE.

Esta declaración se aplica a los productos con marcas

de la CE.

Português

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade,

que este produto está de acordo com as normas ou

documentos normativos EN60745, EN60335, EN55014

e EN61000, em conformidade com as Diretrizes 2004/

108/CE, 2006/95/CE e 98/37/CE do Conselho.

Esta declaração se aplica aos produtos designados CE.

Ελληνικά

EK ∆ΗΛ·ΣΗ ΕΝΑΡΜΝΙΣΜΥ

∆ηλώνυµε µε απ&λυτη υπευθυν&τητα &τι αυτ& τ

πρι&ν είναι εναρµνισµέν µε τα πρ&τυπα ή τα

έγρα(α πρτύπων EN60745, EN60335, EN55014 και

EN61000 σε συµ(ωνία µε τις δηγίες τυ Συµυλίυ

2004/108/EK, 2006/95/EK και 98/37/EK.

Αυτή η δήλωση ισύει στ πρι&ν µε τ σηµάδι CE.

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product is in conformity with standards or standardized

documents EN60745, EN60335, EN55014 and EN61000

in accordance with Council Directives 2004/108/EC,

2006/95/EC and 98/37/EC.

This declaration is applicable to the product affixed CE

marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses

Produkt den Standards oder standardisierten

Dokumenten EN60745, EN60335, EN55014 und EN61000

in Übereinstimmung mit den Direktiven des Europarats

2004/108/CE, 2006/95/CE und 98/37/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung

tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-

sabilité que ce produit est conforme aux normes ou

documents normalisés EN60745, EN60335, EN55014 et

EN61000 en accord avec les Directives 2004/108/CE,

2006/95/CE et 98/37/CE du Conseil.

Cette déclaration s’applique aux produits désignés CE.

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo

prodotto è conforme agli standard o ai documenti

standardizzati EN60745, EN60335, EN55014 e EN61000

conforme alle direttive 2004/108/CE, 2006/95/CE e 98/

37/CE del concilio.

Questa dichiarazione è applicabile ai prodotti cui sono

applicati i marchi CE.

Cordless Impact Driver/Wrench

Akku-Schlagschrauber

Perceuse/visseuse à percussion sur batterie

Avvitatore a impulso a batteria per viti e bulloni

Snoerloze slagschroevendraaier/sleutel

Atornillador/Llave de impacto a batería

Aparafusadora/ Chave de impacto a bateria

¢Ú··ÓÔÎ·ÙÛ¿‚È‰Ô ª·Ù·Ú›·˜/∫ÏÂÈ‰›

Read through carefully and understand these instructions before use.

Diese Anleitung vor Benutzung des Werkzeugs sorgfältig durchlesen und verstehen.

Lire soigneusement et bien assimiler ces instructions avant usage.

Prima dell’uso leggere attentamente e comprendere queste istruzioni.

Deze gebruiksaanwijzing s.v.p. voor gebruik zorgvuldig doorlezen.

Leer

cuidadosamente y comprender estas instrucciones antes del uso.

Antes de usar, leia com cuidado para assimilar estas instruções.

∆ιαάστε πρσεκτικά και κατανήσετε αυτές τις δηγίες πριν τη ρήση.

Handling instructions

Bedienungsanleitung

Mode d’emploi

Istruzioni per l’uso

Gebruiksaanwijzing

Instrucciones de manejo

Instruções de uso

δηγίες ειρισµύ

807

Code No. C99141472

Printed in China

Hitachi Koki Co., Ltd.

1

4

3

87

1

2

8

7

6

WH12DAF2

Variable speed

WH 12DAF2

•

WR 12DAF2

WR12DAF2

H

E

C

I

E

C

F

G

1

2

1

3

2

5

4

〈UC14YFA〉

5

9

A

0

1

8

7

6

C

D

E

〈UC18YG〉

B

Representative office in Europe

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 Willich 1, F. R. Germany

Head office in Japan

Hitachi Koki Co., Ltd.

Shinagawa Intercity Tower A, 15-1, Konan 2-chome,

Minato-ku, Tokyo, Japan

31. 7. 2008

K. Kato

Board Director

Nederlands

EC VERKLARING VAN CONFORMITEIT

Wij verklaren onder eigen verantwoordelijkheid dat dit

produkt conform de richtlijnen of gestandardiseerde

documenten EN60745, EN60335, EN55014 en EN61000

voldoet aan de eisen van EEG Bepalingen 2004/108/

EC, 2006/95/EC en 98/37/EC.

Deze verklaring is van toepassing op produkten

voorzien van de CE-markeringen.

Español

DECLARACIÓN DE CONFORMIDAD DE LA CE

Declaramos bajo nuestra única responsabilidad que

este producto está de acuerdo con las normas o con

los documentos de normalización EN60745, EN60335,

EN55014 y EN61000, según indican las Directrices del

Consejo 2004/108/CE, 2006/95/CE y 98/37/CE.

Esta declaración se aplica a los productos con marcas

de la CE.

Português

DECLARAÇÃO DE CONFORMIDADE CE

Declaramos, sob nossa única e inteira responsabilidade,

que este produto está de acordo com as normas ou

documentos normativos EN60745, EN60335, EN55014

e EN61000, em conformidade com as Diretrizes 2004/

108/CE, 2006/95/CE e 98/37/CE do Conselho.

Esta declaração se aplica aos produtos designados CE.

Ελληνικά

EK ∆ΗΛ·ΣΗ ΕΝΑΡΜΝΙΣΜΥ

∆ηλώνυµε µε απ&λυτη υπευθυν&τητα &τι αυτ& τ

πρι&ν είναι εναρµνισµέν µε τα πρ&τυπα ή τα

έγρα(α πρτύπων EN60745, EN60335, EN55014 και

EN61000 σε συµ(ωνία µε τις δηγίες τυ Συµυλίυ

2004/108/EK, 2006/95/EK και 98/37/EK.

Αυτή η δήλωση ισύει στ πρι&ν µε τ σηµάδι CE.

English

EC DECLARATION OF CONFORMITY

We declare under our sole responsibility that this

product is in conformity with standards or standardized

documents EN60745, EN60335, EN55014 and EN61000

in accordance with Council Directives 2004/108/EC,

2006/95/EC and 98/37/EC.

This declaration is applicable to the product affixed CE

marking.

Deutsch

ERKLÄRUNG ZUR KONFORMITÄT MIT CE-REGELN

Wir erklären mit alleiniger Verantwortung, daß dieses

Produkt den Standards oder standardisierten

Dokumenten EN60745, EN60335, EN55014 und EN61000

in Übereinstimmung mit den Direktiven des Europarats

2004/108/CE, 2006/95/CE und 98/37/CE entspricht.

Diese Erklärung gilt für Produkte, die die CE-Markierung

tragen.

Français

DECLARATION DE CONFORMITE CE

Nous déclarons sous notre seule et entière respon-

sabilité que ce produit est conforme aux normes ou

documents normalisés EN60745, EN60335, EN55014 et

EN61000 en accord avec les Directives 2004/108/CE,

2006/95/CE et 98/37/CE du Conseil.

Cette déclaration s’applique aux produits désignés CE.

Italiano

DICHIARAZIONE DI CONFORMITÀ CE

Si dichiara sotto nostra responsabilità che questo

prodotto è conforme agli standard o ai documenti

standardizzati EN60745, EN60335, EN55014 e EN61000

conforme alle direttive 2004/108/CE, 2006/95/CE e 98/

37/CE del concilio.

Questa dichiarazione è applicabile ai prodotti cui sono

applicati i marchi CE.

3 100

17

L

R

U

V V

2

14

O

J

N

13

3

M

J

11

K

J

12

L

109

(A)

5

1

J

16

,

.

,.

J

S

Q

R

T

R

15

Q

P

4

3

2

(B)

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 willich 1, F. R. Germany

Tel: +49 2154 49930

Fax: +49 2154 499350

URL: http://www.hitachi-powertools.de

Hitachi Power Tools Netherlands B. V.

Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands

Tel: +31 30 6084040

Fax: +31 30 6067266

URL: http://www.hitachi-powertools.nl

Hitachi Power Tools (U. K.) Ltd.

Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom

Tel: +44 1908 660663

Fax: +44 1908 606642

URL: http://www.hitachi-powertools.co.uk

Hitachi Power Tools France S. A. S.

Prac del’ Eglantier 22, rue des Crerisiers Lisses, C. E. 1541,

91015 EVRY CEDEX, France

Tel: +33 1 69474949

Fax: +33 1 60861416

URL: http://www.hitachi-powertools.fr

Hitachi Power Tools Belgium N.V. / S.A.

Koningin Astridlaan 51, 1780 Wemmel, Belgium

Tel: +32 2 460 1720

Fax: +32 2 460 2542

URL http://www.hitachi-powertools.be

Hitachi Fercad Power Tools Italia S.p.A

Via Retrone 49-36077, Altavilla Vicentina (VI), Italy

Tel: +39 0444 548111

Fax: +39 0444 548110

URL: http://www.hitachi-powertools.it

Hitachi Power Tools lberica, S.A.

C / Migjorn, s/n, Poligono Norte, 08226 Terrassa, Barcelona, Spain

Tel: +34 93 735 6722

Fax: +34 93 735 7442

URL: http://www.hitachi-powertools.es

Hitachi Power Tools Österreich GmbH

Str. 7, Objekt 58/A6, Industriezentrum NÖ –Süd 2355

Wiener Neudorf, Austria

Tel: +43 2236 64673/5

Fax: +43 2236 63373

3 100

17

L

R

U

V V

2

14

O

J

N

13

3

M

J

11

K

J

12

L

109

(A)

5

1

J

16

,

.

,.

J

S

Q

R

T

R

15

Q

P

4

3

2

(B)

Hitachi Power Tools Europe GmbH

Siemensring 34, 47877 willich 1, F. R. Germany

Tel: +49 2154 49930

Fax: +49 2154 499350

URL: http://www.hitachi-powertools.de

Hitachi Power Tools Netherlands B. V.

Brabanthaven 11, 3433 PJ Nieuwegein, The Netherlands

Tel: +31 30 6084040

Fax: +31 30 6067266

URL: http://www.hitachi-powertools.nl

Hitachi Power Tools (U. K.) Ltd.

Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ, United Kingdom

Tel: +44 1908 660663

Fax: +44 1908 606642

URL: http://www.hitachi-powertools.co.uk

Hitachi Power Tools France S. A. S.

Prac del’ Eglantier 22, rue des Crerisiers Lisses, C. E. 1541,

91015 EVRY CEDEX, France

Tel: +33 1 69474949

Fax: +33 1 60861416

URL: http://www.hitachi-powertools.fr

Hitachi Power Tools Belgium N.V. / S.A.

Koningin Astridlaan 51, 1780 Wemmel, Belgium

Tel: +32 2 460 1720

Fax: +32 2 460 2542

URL http://www.hitachi-powertools.be

Hitachi Fercad Power Tools Italia S.p.A

Via Retrone 49-36077, Altavilla Vicentina (VI), Italy

Tel: +39 0444 548111

Fax: +39 0444 548110

URL: http://www.hitachi-powertools.it

Hitachi Power Tools lberica, S.A.

C / Migjorn, s/n, Poligono Norte, 08226 Terrassa, Barcelona, Spain

Tel: +34 93 735 6722

Fax: +34 93 735 7442

URL: http://www.hitachi-powertools.es

Hitachi Power Tools Österreich GmbH

Str. 7, Objekt 58/A6, Industriezentrum NÖ –Süd 2355

Wiener Neudorf, Austria

Tel: +43 2236 64673/5

Fax: +43 2236 63373

4

English Deutsch Français Italiano

1

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

12 V Rechargeable

battery

Latch

Handlee

Insert

Pull out

Insert

Pilot lamp

Hole for connecting the

rechargeable battery

Movement

Guide sleeve

Hexagonal hole in the

anvil

Driver bit

Hexagonal socket

Groove

Anvil

Ring

Hole

Plunger

Hook

Spring

Larger diameter faces

away

Switch

Phillips-head screwdriver

Screw

Arrow

Hook cover

Indentation

Protuberance

AAAA batteries

Push button

Push

Batteria ricaricabile,

12 V

Fermo

Impugnatura

Inserire

Estrarre

Inserire

Spia

Foro di collegamento

della batería recargable

Movimento

Manicotto guida

Foro esagonale nel

basaménto

Testa avvitatrice

Chiave de incavo

esagonale

Scanalature

Basamento

Spina

Anello

Foro

Stantuffo

Grancio

Molla

Diametro più grande

lontano da sé

Interruttore

Cacciavite con testa a

croce

Vite

Freccia

Coperchio gancio

Tacca

Sporgenza

Pile AAAA

Tasto da premere

Spingere

Akkumulator, 12 V

Schnapper

Griff

Einsatz

Herausziehen

Einsetz

Kontrollampe

Anschlußlon für

Akkumulator

Bewegung

Führungsmanschette

Sechskantloch in der

Schabotte

Dreherspitze

Sechskantbuchse

Schlitz

Schabotte

Stift

Ring

Öffnung

Preßkolben

Haken

Feder

Der große Durchmesser

weist zur anderen Seite

Schalter

Kreuzschlitzschrauben-

zieher

Schraube

Pfeil

Hakenabdeckung

Einkerbung

Vorsprung

Batterien der Größe

AAAA

Druckknopf

Drücken

Batterie rechargeable,

12 V

Loquet

Poignée

Insérer

Tirer

Insérer

Lampe pilote

Orifice de raccordement

de la batterie rechargeable

Mouvement

Manchon-guide

Orifice hexagonal de la

chabotte

Mèche

Douille hexagonal

Rainure

Chabotte

Goupille

Aunneau

Orifice

Piston

Crochet

Ressort

Gros diamètre dirigé

vers l’extérieur

Interrupteur

Tournevis à tête Phillips

Vis

Flèche

Cache de crochet

Entaille

Saillie

Piles AAAA

Poussoir

Pousser

00Table_WH12DAF2_WE 5/14/08, 18:104

5

Nederlands Español Português Ελληνικά

1

2

3

4

5

6

7

8

9

0

A

B

C

D

E

F

G

H

I

J

K

L

M

N

O

P

Q

R

S

T

U

V

Oplaadbare batterij, 12 V

Vergrendeling

Handgreep

Insteken

Uittrekken

Insteken

Kontrolelampje

Aansluiting voor

oplaadbare batterij

Beweging

Geleide ring

Zeshoekige opening in

het draaistuk

Schroefstuk

Zeschoekige bus

Groef

Draaistuk

Pen

Ring

Opening

Plunjer

Haak

Veer

De grotere diameter wijst

van u vandaan

Schakelaar

Kruiskopschroevendraaier

Schroef

Pijl

Afdekking haak

Inkeping

Uitsteeksel

AAAA batterijen

Druktoets

Drukken

12 V Επαναρτιµενη

µπαταρία

Μάνδαλ

ερύλι

Εισωρήστε

Βραήτε έω

Εισωρήστε

∆κιµαστική λάµπα

Τρύπα για την σύνδεση

της επαναρτιµενης

µπαταρίας

Κίνηση

$δηγητικς ραίνας

Εάγωνη τρύπα στν

άκµνα

Λεπίδα κίνησης

Μακριά υπδή

Αυλάκωση

Άκµνας

Πείρς

∆ακτύλις

Τρύπα

Έµλ

Άγκιστρ

Ελατήρι

Η µεγαλύτερη

διάµετρς λέπει πρς

άλλη κατεύθυνση

∆ιακπτης

Κατσαίδι κεαλής

Phillips

Βίδα

Βέλς

Κάλυµµα αγκίστρυ

Αυλάκωση

Πρεή

ΑΑΑΑ µπαταρίες

Κυµπί ώθησης

Σπρώε

Bateria de 12 V

recarregável

Lingüeta

Cabo

Inserir

Retirar

Inserir

Lâmpada piloto

Orifício para conectar a

bateria recarregável

Movimento

Manga-guia

Orifício sextavado na

bigorna

Chave de fenda

Encaixe longo

Ranhura

Bigorna

Pino

Anel

Orifício

Pistão

Gancho

Mola

O diâmetro maior dá

para fora

Comutador

Chave Phillips

Parafuso

Seta

Tampa do gancho

Entalhe

Protuberância

Pilhas AAAA

Interruptor

Apertar

Batería recargable,

12 V

Enganche

Mango

Insertar

Sacar

Insertar

Lámpara piloto

Agujero para conectar

la batería recargable

Movimiento

Manguito guía

Orificio hexagonal en el

yunque

Punta de destornillador

Recaptáculo hexanogal

Ranura

Yunque

Pasador

Anillo

Orificio

Embolo

Gancho

Resorte

El diámetro más grande

queda en dirección

opuesta

Interruptor

Destornillador con cabeza

Phillips

Tornillo

Flecha

Cubierta del gancho

Indentación

Saliente

Pilas AAAA

Pulsador

Presionar

00Table_WH12DAF2_WE 5/14/08, 18:105

6

Symbols

WARNING

The following show

symbols used for the

machine. Be sure that

you understand their

meaning before use.

Symbole

WARNUNG

Die folgenden Symbole

werden für diese Maschine

verwendet. Achten Sie

darauf, diese vor der

Verwendung zu verstehen.

Symboles

AVERTISSEMENT

Les symboles suivants

sont utilisés pour l’outil.

Bien se familiariser avec

leur signification avant

d’utiliser l’outil.

Simboli

AVVERTENZA

Di seguito mostriamo i

simboli usati per la

macchina. Assicurarsi di

comprenderne il

significato prima dell’uso.

Read all safety

warnings and all

instructions.

Failure to follow the

warnings and

instructions may result

in electric shock, fire

and/or serious injury.

Lesen Sie sämtliche

Sicherheitshinweise und

Anweisungen durch.

Wenn die Warnungen und

Anweisungen nicht befolgt

werden, kann es zu

Stromschlag, Brand und/

oder ernsthaften

Verletzungen kommen.

Lire tous les avertissements

de sécurité et toutes les

instructions.

Tout manquement à observer

ces avertissements et

instructions peut engendrer

des chocs électriques, des

incendies et/ou des blessures

graves.

Leggere tutti gli avvertimenti

di sicurezza e tutte le

istruzioni.

La mancata osservanza degli

avvertimenti e delle istruzioni

potrebbe essere causa di

scosse elettriche, incendi e/o

gravi lesioni.

Symbolen

WAARSCHUWING

Hieronder staan symbolen

afgebeeld die van toepassing

zijn op deze machine. U

moet de betekenis hiervan

begrijpen voor gebruik.

Símbolos

ADVERTENCIA

A continuación se muestran

los símbolos usados para la

máquina. Asegúrese de

comprender su significado

antes del uso.

Símbolos

AVISO

A seguir aparecem os

símbolos utilizados pela

máquina. Assimile bem

seus significados antes

do uso.

Lees alle waarschuwingen en

instructies aandachtig door.

Nalating om de

waarschuwingen en

instructies op te volgen kan in

een elektrische schok, brand

en/of ernstig letsel resulteren.

Lea todas las instrucciones y

advertencias de seguridad.

Si no se siguen las

advertencias e instrucciones,

podría producirse una

descarga eléctrica, un

incendio y/o daños graves.

Leia todas as instruções e

avisos de segurança.

Se não seguir todas as

instruções e os avisos, pode

provocar um choque eléctrico,

incêndio e/ou ferimentos

graves.

Only for EU countries

Do not dispose of electric

tools together with household

waste material!

In observance of European

Directive 2002/96/EC on waste

electrical and electronic

equipment and its

implementation in accordance

with national law, electric

tools that have reached the

end of their life must be

collected separately and

returned to an

environmentally compatible

recycling facility.

Nur für EU-Länder

Werfen Sie Elektrowerkzeuge

nicht in den Hausmüll!

Gemäss Europäischer

Richtlinie 2002/96/EG über

Elektro- und Elektronik-

Altgeräte und Umsetzung in

nationales Recht müssen

verbrauchte Elektrowerkzeuge

getrennt gesammelt und einer

umweltgerechten

Wiederververtung zugeführt

werden.

Pour les pays européens

uniquement

Ne pas jeter les appareils

électriques dans les ordures

ménagères!

Conformément à la directive

européenne 2002/96/EG relative

aux déchets d’équipements

électriques ou électroniques

(DEEE), et à sa transposition

dans la législation nationale, les

appareils électriques doivent

être collectés à part et être

soumis à un recyclage

respectueux de

l’environnement.

Solo per Paesi UE

Non gettare le

apparecchiature elettriche tra i

rifiuti domestici.

Secondo la Direttiva Europea

2002/96/CE sui rifiuti di

apparecchiature elettriche ed

elettroniche e la sua

attuazione in conformità alle

norme nazionali, le

apparecchiature elettriche

esauste devono essere

raccolte separatamente, al fine

di essere reimpiegate in modo

eco-compatibile.

Alleen voor EU-landen

Geef elektrisch gereedschap

niet met het huisvuil mee!

Volgens de Europese richtlijn

2002/96/EG inzake oude

elektrische en elektronische

apparaten en de toepassing

daarvan binnen de nationale

wetgeving, dient gebruikt

elektrisch gereedschap

gescheiden te worden

ingezameld en te worden

afgevoerd naar een recycle

bedrijf dat voldoet aan de

geldende milieu-eisen.

Apenas para países da UE

Não deite ferramentas

eléctricas no lixo doméstico!

De acordo com a directiva

europeia 2002/96/CE sobre

ferramentas eléctricas e

electrónicas usadas e a

transposição para as leis

nacionais, as ferramentas

eléctricas usadas devem ser

recolhidas em separado e

encaminhadas a uma

instalação de reciclagem dos

materiais ecológica.

Sólo para países de la Unión

Europea

¡No deseche los aparatos

eléctricos junto con los residuos

domésticos!

De conformidad con la Directiva

Europea 2002/96/CE sobre

residuos de aparatos eléctricos y

electrónicos y su aplicación de

acuerdo con la legislación

nacional, las herramientas

eléctricas cuya vida útil haya

llegado a su fin se deberán recoger

por separado y trasladar a una

planta de reciclaje que cumpla con

las exigencias ecológicas.

™‡Ì‚ÔÏ·

¶ƒ√™√Ã∏

Τα παρακάτω δείνυν τα

σύµλα πυ ρησιµπιύνται

στ µηάνηµα. Βεαιωθείτε τι

κατανείτε τη σηµασίας τυς

πριν τη ρήση.

¢È·‚¿˙ÂÙÂ ﬁÏÂ˜ ÙÈ˜

ÚÔÂÈ‰ÔÔÈ‹ÛÂÈ˜ ·ÛÊ·ÏÂ›·˜ Î·È

ﬁÏÂ˜ ÙÈ˜ Ô‰ËÁ›Â˜.

Η µη τήρηση των πρειδπιήσεων

και δηγιών µπρεί να πρκαλέσει

ηλεκτρπληία, πυρκαγιά και/ή

σαρ τραυµατισµ.

Mvo για τις ώρες της EE

Mηv πετάτε τα ηλεκτρικά

εργαλεία στov κάδo oικιακώv

απoρριµµάτωv!

Σύµ#ωvα µε τηv εuρωπαϊκή

oδηγία 2002/96/EK περί

ηλεκτρικώv και ηλεκτρovικώv

σuσκεuώv και τηv

εvσωµάτωσή της στo εθvικ

δίκαιo, τα ηλεκτρικά

εργαλεία πρέπει vα

σuλλέγovται εωριστά και

vα επιστρέ#ovται για

αvακύκλωση µε τρπo #ιλικ

πρoς τo περιάλλov.

01Eng_WH12DAF2_WE 5/14/08, 18:116

English

7

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result

in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit.

Cluttered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust.

Power tools create sparks which may ignite the

dust or fumes.

c) Keep children and bystanders away while

operating a power tool.

Distractions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way.

Do not use any adapter plugs with earthed

(grounded) power tools.

Unmodified plugs and matching outlets will

reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators.

There is an increased risk of electric shock if

your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions.

Water entering a power tool will increase the

risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts.

Damaged or entangled cords increase the risk

of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces

the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply.

Use of an RCD reduces the risk of electric shock.

3) Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or medication.

A moment of inattention while operating power

tools may result in serious personal injury.

b) Use personal protective equipment. Always wear

eye protection.

Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce

personal injuries.

c) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or

carrying the tool.

Carrying power tools with your finger on the

switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on.

A wrench or a key left attached to a rotating part

of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times.

This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves

away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used.

Use of dust collection can reduce dust related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the correct

power tool for your application.

The correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch does

not turn it on and off.

Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools.

Such preventive safety measures reduce the risk

of starting the power tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts

and any other condition that may affect the

power tools operation.

If damaged, have the power tool repaired before

use.

Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with sharp

cutting edges are less likely to bind and are

easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, taking

into account the working conditions and the

work to be performed.

Use of the power tool for operations different from

those intended could result in a hazardous situation.

01Eng_WH12DAF2_WE 5/14/08, 18:117

English

8

5) Battery tool use and care

a) Recharge only with the charger specified by the

manufacturer.

A charger that is suitable for one type of battery

pack may create a risk of fire when used with

another battery pack.

b) Use power tools only with specifically designated

battery packs.

Use of any other battery packs may create a risk

of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects like paper clips, coins,

keys, nails, screws, or other small metal objects

that can make a connection from one terminal

to another.

Shorting the battery terminals together may

cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause

irritation or burns.

6) Service

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts.

This will ensure that the safety of the power tool

is maintained.

PRECAUTION

Keep children and infirm persons away.

When not in use, tools should be stored out of reach of

children and infirm persons.

PRECAUTIONS FOR CORDLESS IMPACT

DRIVER

1. This is portable tool for tightening and loosenig

screws. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. After installing the driver bit, pull lightly out the

bit to make sure that it does not come loose. If

the bit is not installed properly, it can come loose

during use, which can be dangerous.

5. Use the bit that matches the screw.

6. Tightening a screw with the impact driver at an

angle to that screw can damage the head of the

screw and the proper force will not be transmitted

to the screw. Tighten with this impact driver lined

up straight with the screw.

7. Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

8. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

9. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

10. Never disassemble the rechargeable battery and

charger.

11. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great

electric current and overheat. It results in burn or

damage to the battery.

12. Do not dispose of the battery in fire.

If the battery burnt, it may explode.

13. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

14. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

15. Using an exhausted battery will damage the

charger.

PRECAUTIONS FOR CORDLESS IMPACT

WRENCH

1. This is a portable tool for tightening and loosening

bolts and nuts. Use it only for these operation.

2. Use the earplugs if using for a long time.

3. One-hand operation is extremely dangerous; hold

the unit firmly with both hands when operating.

4. Check that the socket is not cracked or broken.

Broken or cracked sockets are dangerous. Check

the socket before using it.

5. Secure the socket with the socket pin and the ring.

If the socket pin or ring securing the socket is damaged,

the socket may come off from the impact wrench,

which is quite dangerous. Do not use socket pins

or rings that are deformed, worn out, cracked, or in

any other way damaged. Always make sure to install

the socket pin and ring in the correct position.

6. Check the tightening torque.

The appropriate torque for tightening a bolt

depends on the material the bolt is made of, its

dimensions, grade, etc.

Also, the tightening torque generated by this impact

wrench depends on the materials and dimensions

of the bolt, how long the impact wrench is applied

for the way in which the socket is installed, etc.

Also the torque when the battery has just been

charged and when it is about to run out are slightly

different. Use a torque wrench to check that the

bolt has been tightened with the appropriate torque.

7. Stop the impact wrench before switching the

direction of rotation. Always release the switch

and wait for impact wrench to stop before

switching the direction of rotation.

8. Never touch the turning part.

Do not allow the turning socket section to get near

your hands or any other part of your body. You could

be cut or caught in the socket. Also, be careful not

to touch the socket after using continuously it for a

long time. It gets quite hot and could burn you.

9. Never let the impact wrench turn without a load

when using the universal joint.

If the socket turns without being connected to a load,

the universal joint causes the socket to turn wildly.

You could get hurt or the movement of the socket

could shake the impact wrench so much as to

make you drop it.

10. Always charge the battery at a temperature of 0

– 40°C.

A temperature of less than 0°C will result in over

charging which is dangerous. The battery cannot

be charged at a temperature greater than 40°C.

The most suitable temperature for charging is that

of 20 – 25°C.

11. Do not use the charger continuously.

When one charging is completed, leave the charger

for about 15 minutes before the next charging of

battery.

12. Do not allow foreign matter to enter the hole for

connecting the rechargeable battery.

01Eng_WH12DAF2_WE 5/14/08, 18:118

English

9

13. Never disassemble the rechargeable battery and

charger.

14. Never short-circuit the rechargeable battery.

Short-circuiting the battery will cause a great

electric current and overheat. It results in burn or

damage to the battery.

15. Do not dispose of the battery in fire.

If the battery burnt, it may explode.

16. Do not insert object into the air ventilation slots

of the charger.

Inserting metal objects or inflammables into the

charger air ventilation slots will result in electrical

shock hazard or damaged charger.

SPECIFICATIONS

POWER TOOL

Maximum 130 N·m {1330 kgf·cm}

Tightening is M12 high tension bolt

(strength grade 12.9), when fully

charged at 20°C temp.

Tightening time: 3 sec.

Model WH12DAF2 WR12DAF2

No-load speed 0 – 2500 min

–1

Capacity M4 – M8 (Small screw) M6 – M14 (Ordinary bolt)

M5 – M12 (Ordinary bolt) M6 – M10 (High tension bolt)

M5 – M10 (High tension bolt)

Tightening torque

Rechargeable battery EB1214S: Ni-Cd battery, 12 V (1.4 Ah 10 cells)

EB1220BL: Ni-Cd battery, 12 V (2.0 Ah 10 cells)

EB1226HL: Ni-MH battery, 12 V (2.6 Ah 10 cells)

Weight 1.6 kg (EB1214S Installation)

Maximum 110 N·m {1120 kgf·cm}

Tightening is M12 high tension bolt

(strength grade 12.9), when fully

charged at 20°C temp.

Tightening time: 3 sec.

17. Bring the battery to the shop from which it was

purchased as soon as the post-charging battery

life becomes too short for practical use. Do not

dispose of the exhausted battery.

18. Using an exhausted battery will damage the

charger.

MODEL

WH12DAF2:with charger and case

WR12DAF2:with charger and case

CHARGER

Model UC14YFA UC18YG

Charging time EB1214S: Approx. 30 min. (at 20°C) EB1214S: Approx. 30 min. (at 20°C)

EB1220BL: Approx. 50 min. (at 20°C) EB1220BL: Approx. 50 min. (at 20°C)

EB1226HL: Approx. 60 min. (at 20°C) ×

Charging voltage 7.2 – 14.4 V 7.2 – 18 V

Weight 0.6 kg 0.3 kg

“x” Indicates that the battery pack is not compatible with that specific charger.

NOTE: The charging time may vary according to the ambient temperature and power source voltage.

STANDARD ACCESSORIES

1. Charger (UC14YFA or UC18YG) ............................... 1

2. Plastic case ................................................................ 1

Standard accessories are subject to change without

notice.

OPTIONAL ACCESSORIES

(Sold separately)

1. Battery (EB1214S, EB1220BL, EB1226HL)

2. For WH12DAF2

There are two types of attachment sizes for the driver

bit and the socket. Please refer to the table below and

select the attachment size for the driver bit or socket

that is appropriate for your WH12DAF2.

01Eng_WH12DAF2_WE 5/14/08, 18:119

English

10

Attachment size Purchase location

Type-L

Type-S

Republic of Korea,

Taiwan, Hong Kong,

People’s Republic of

China, Republic of

Singapore

Other than above

regions.

17mm

12mm

13mm

9mm

3. For WR12DAF2

The WR12DAF2 type is a 12.7 square driver

specification. Please select the socket with the

appropriate attachment size.

Optional accessories are subject to change without notice.

APPLICATION

〈WH12DAF2〉

䡬 Driving and removing of small screws, small bolts,

etc.

〈WR12DAF2〉

䡬 Tightening and loosening of all types of bolts and

nuts, used for securing structural items

BATTERY REMOVAL/INSTALLATION

1. Battery removal

Hold the handle tightly and push the battery latch to

remove the battery. (See Fig. 1 and 2)

CAUTION:

Never short-circuit the battery.

2. Battery installation

Insert the battery while observing its polarities. (See

Fig. 2)

CHARGING

〈UC14YFA〉

Before using the power tool, charge the battery as follows.

1. Connect the charger’s power cord to a receptacle.

When the power cord is connected, the charger’s

pilot lamp will blink in red. (At 1-second intervals.)

2. Insert the battery into the charger.

Insert the battery firmly, in the direction shown in

Fig. 3, until it contacts the bottom of the charger

compartment.

CAUTION:

䡬 If the battery is inserted in the reverse direction, not

only recharging will become impossible, but it may

also cause problems in the charger such as deformed

recharging terminal.

3. Charging

When inserting a battery in the charger, charging will

commence and the pilot lamp will light up

continuously in red.

When the battery becomes fully recharged, the pilot

lamp will blink in red. (At 1-second intervals.) (See

Table 1)

(1) Pilot lamp indication

The indications of the pilot lamp will be as shown in

Table 1, according to the condition of the charger or

the rechargeable battery.

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Malfunction in the battery

or the charger.

The battery temperature

is high, making

recharging impossible.

Table 1

Indications of the lamps

Lights continuously

01Eng_WH12DAF2_WE 5/14/08, 18:1110

English

11

(2) Regarding the temperatures of the rechargeable battery

The temperatures for rechargeable batteries are as

shown in the table below, and batteries that have

become hot should be cooled for a while before

being recharged.

Table 2 Recharging ranges of batteries

4. Disconnect the charger’s power cord from the receptacle.

5. Hold the charger firmly and pull out the battery.

NOTE:

Be sure to pull out the battery from the charger after

use, and then keep it.

Regarding electric discharge in case of new

batteries, etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer

(1) Recharge the batteries before they become completely

exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the battery

and recharge it after it has cooled for a while.

CAUTION:

䡬 If the battery is charged while it is heated because it

has been left for a long time in a location subject to

direct sunlight or because the battery has just been

used, the pilot lamp of the charger lights up green. In

such a case, first let the battery cool, then start

charging.

䡬 When the pilot lamp flickers in red quickly (at 0.2-

second intervals), check for and take out any foreign

objects in the charger’s battery installation hole. If

there are no foreign objects, it is probable that the

battery or charger is malfunctioning. Take it to your

Authorized Service Center.

䡬 Since the built-in micro computer takes about 3

seconds to confirm that the battery being charged

with UC14YFA is taken out, wait for a minimum of 3

seconds before reinserting it to continue charging. If

the battery is reinserted within 3 seconds, the battery

may not be properly charged.

〈

UC18YG

〉

Before using the power tool, charge the battery as follows.

1. Connect the charger power cord to the receptacle

Connecting the power cord will turn on the charger.

2. Insert the battery into the charger

Insert the battery firmly while observing its direction,

until it contacts the bottom of the charger (the pilot

lamp lights up) (See Fig. 4).

CAUTION

If the pilot lamp does not light up, pull out the

power cord from the receptacle and check the

battery mounting condition.

䡬 Regarding the temperatures of the rechargeable

battery

The temperatures for rechargeable batteries are as

shown in Table 3.

Table 3 Recharging ranges of batteries

䡬 The pilot lamp goes off to indicate that the battery is

fully charged.

The battery charging time becomes longer when a

temperature is low or the voltage of the power source

is too low.

When the pilot lamp does not go off even if more

than 120 minutes have elapsed after starting of the

charging, stop the charging and contact your HITACHI

AUTHORIZED SERVICE CENTER.

CAUTION

If the battery is heated due to direct sunlight, etc.,

just after operation, the charger pilot lamp may

not light up. At that time, cool the battery first,

then start charging.

3. Disconnect the charger’s power cord from the

receptacle

4. Hold the charger firmly and pull out the battery

NOTE

After charging, pull out batteries from the charger

first, and then keep the batteries properly.

Regarding electric discharge in case of new batteries,

etc.

As the internal chemical substance of new batteries

and batteries that have not been used for an extended

period is not activated, the electric discharge might

be low when using them the first and second time.

This is a temporary phenomenon, and normal time

required for recharging will be restored by recharging

the batteries 2 – 3 times.

How to make the batteries perform longer.

(1) Recharge the batteries before they become

completely exhausted.

When you feel that the power of the tool becomes

weaker, stop using the tool and recharge its battery.

If you continue to use the tool and exhaust the electric

current, the battery may be damaged and its life will

become shorter.

Temperatures at

Rechargeable batteries which the battery

can be recharged

EB1214S, EB1220BL –5°C – 60°C

EB1226HL 0°C – 45°C

Temperatures at

Rechargeable batteries which the battery

can be recharged

EB1214S, EB1220BL 0°C – 45°C

01Eng_WH12DAF2_WE 5/14/08, 18:1111

English

12

Injury may result if you carry the equipment

suspended from the waist belt with sharp tipped

components such as drill bit attached.

1. Using the light equipped hook

The light equipped hook can be installed on the right

or left side and the angle can be adjusted in 5 steps

between 0° and 80°.

(1) Operating the hook

(a) Pull out the hook toward you in the direction of

arrow (A) and turn in the direction of arrow (B).

(Fig. 9)

(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,

60°, 80°).

Adjust the angle of the hook to the desired position

for use.

(2) Switching the hook position

CAUTION:

Incomplete installation of the hook may result in

bodily injury when used.

(a) Securely hold the main unit and remove the screw

using a slotted head screwdriver or a coin. (Fig.

10)

(b) Remove the hook and spring. (Fig. 11)

(c) Install the hook and spring on the other side and

securely fasten with screw. (Fig. 12)

NOTE:

Pay attention to the spring orientation. Install the

spring with larger diameter away from you. (Fig. 12)

(3) Using as an auxiliary light

(a) Press the switch to turn off the light.

If forgotten, the light will turn off automatically

after 15 minutes.

(b) The direction of the light can be adjusted within

the range of hook positions 1 - 5. (Fig. 13)

䡬 Lighting time

AAAA manganese batteries: approx. 15 hrs.

AAAA alkali batteries: approx. 30 hrs.

CAUTION:

Do not look directly into the light.

Such actions could result in eye injury.

(4) Replacing the batteries

(a) Loosen the hook screw with a phillips-head

screwdriver (No. 1). (Fig. 14)

Remove the hook cover by pushing in the direction

of the arrow. (Fig. 15)

(b) Remove the old batteries and insert the new

batteries. Align with the hook indications and

position the plus (+) and minus (–) terminals

correctly. (Fig. 16)

(c) Align the indentation in the hook main body with

the protuberance of the hook cover, press the

hook cover in the direction opposite to that of the

arrow shown in Fig. 15 and then tighten the screw.

Use commercially available AAAA batteries

(1.5 V).

NOTE:

Do not tighten the screw excessively. Such action

could strip the screw threads.

CAUTION:

䡬 Failure to observe the following can result in battery

leakage, rust or malfunction.

Position the plus (+) and minus (–) terminals correctly.

Replace both batteries at the same time. Do not mix

old and new batteries.

Remove exhausted batteries from the hook

immediately.

(2) Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after

use. If such a battery is recharged immediately after

use, its internal chemical substance will deteriorate,

and the battery life will be shortened. Leave the

battery and recharge it after it has cooled for a while.

PRIOR TO OPERATION

1. Preparing and checking the work environment

Make sure that the work site meets all the conditions

laid forth in the precautions.

2. Checking the battery

Make sure that the battery is installed firmly. If it is at

all loose it could come off and cause an accident.

3. Installing the bit (WH12DAF2)

Always follow the following procedure to install driver

bit. (Fig. 5)

(1) Pull the guide sleeve away from front of the tool.

(2) Insert the bit into the hexagonal hole in the anvil.

(3) Release the guide sleeve and it returns to its original

position.

CAUTION:

If the guide sleeve does not return to its original

position, then the bit is not installed properly.

4. Selecting the socket matched to the bolt

(WR12DAF2)

Be sure to use a socket which is matched to the bolt

to be tightened. Using an improper socket will not

only result in insufficient tightening but also in

damage to the socket or nut.

A worn or deformed hex. or square-holed socket will

not give an adequate tightness for fitting to the nut or

anvil, consequently resulting in loss of tightening

torque.

Pay attention to wear of socket hole, and replace

before further wear has developed.

Finally, install the socket prescribed in Item 5. The

section on “Optional Accessories” details the

relationship between bolt sizes and sockets. Sockets

are named according to the dihedral width of the

hexagonal hole.

5. Installing a socket (WR12DAF2)

Select the socket to be used.

䢇 Pin, O-ring type (Fig. 6 and 7)

(1) Align the hole in the socket with the hole in the anvil

and insert the anvil into the socket.

(2) Insert the pin into the socket.

(3) Attach the ring to the groove on the socket.

䢇 Plunger type (Fig. 8)

Align the plunger located in the square part of the

anvil with the hole in the hex. socket. Then push the

plunger, and mount the hex. socket on the anvil.

Check that the plunger is fully engaged in the hole.

When removing the socket, reverse the sequence.

HOW TO USE

CAUTION:

䡬 When using the light equipped hook, pay sufficient

attention so that the main equipment does not fall. If

the tool falls, there is a risk of accident.

䡬 Do not attach the tip tool except phillips bit to the tool

main unit when carrying the tool main unit with the

light equipped hook suspended from a waist belt.

01Eng_WH12DAF2_WE 5/14/08, 18:1112

English

13

䡬 Do not discard batteries together with normal trash

and do not throw batteries into fire.

䡬 Store batteries out of the reach of children.

䡬 Use batteries correctly in accordance with the battery

specifications and indications.

2. Check the rotational direction

The bit rotates clockwise (viewed from the rear side)

by pushing the R-side of the push button.

The L-side of the push button is pushed to turn the bit

counterclockwise. (See Fig. 17) (The

L

and

R

marks

are provided on the body.)

CAUTION:

The push button cannot be switched while the impact

driver is turning. To switch the push button, stop the

impact driver, then set the push button.

3. Switch operation

䡬 When the trigger switch is depressed, the tool rotates.

When the trigger is released, the tool stops.

䡬 The rotational speed can be controlled by varying the

amount that the trigger switch is pulled. Speed is low

when the trigger switch is pulled slightly and increases

as the trigger switch is pulled more.

4. Tightening and loosening screws (WH12DAF2)

Install the bit that matches the screw, line up the bit

in the grooves of the head of the screw, then tighten

it.

Push the impact driver just enough to keep the bit

fitting the head of the screw.

CAUTION:

Applying the impact driver for too long tightens the

screw too much and can break it.

Tightening a screw with the impact driver at an angle

to that screw can damage the head of the screw and

the proper force will not be transmitted to the screw.

Tighten with this impact driver lined up straight with

the screw.

5. Number of screws tightenings possible (WH12DAF2)

Please refer to the table below for the number of

screw tightened possible with one charge.

EB1214S

These values may vary slightly, according to

surrounding temperature and battery characteristics.

6. Number of bolt tightened possible (WR12DAF2)

Please refer to the table below for the number of bolt

tightened possible with one charge.

EB1214S

These values may vary slightly, according to

surrounding temperature and battery characteristics.

NOTE:

The use of the battery EB1226HL in a cold condition

(below 0 degree Centigrade) can sometimes result in

the weakened tightening torque and reduced amount

of work. This, however, is a temporary phenomenon,

and returns to normal when the battery warms up.

OPERATIONAL CAUTIONS

1. Resting the unit after continuous work

After use for continuous bolt-tightening work, rest

the unit for 15 minutes or so when replacing the

battery. The temperature of the motor, switch, etc.,

will rise if the work is started again immediately after

battery replacement, eventually resulting in burnout.

NOTE:

Do not touch the hammer case, as it gets very hot

during continuous work.

2. Cautions on use of the speed control switch

This switch has a built-in, electronic circuit which

steplessly varies the rotation speed. Consequently,

when the switch trigger is pulled only slightly (low

speed rotation) and the motor is stopped while

continuously driving in screws, the components of

the electronic circuit parts may overheat and be

damaged.

3. Tightening torque

Refer to Fig. 18 and Fig. 19 for the tightening torque

of bolts (according to size), under the conditions

shown in Fig. 20. Please use this example as a general

reference, as tightening torque will vary according to

tightening conditions.

NOTE:

䡬 If a long striking time is used, screws will be strongly

tightened. This may cause the screw to break, or may

damage the tip of the bit.

䡬 If the unit is held at an angle to the screw being

tightened, the head of the screw may be damaged, or

the specified torque may not be transmitted to the

screw. Always keep the unit and the screw being

tightened in a straight line.

4. Use a tightening time suitable for the screw

The appropriate torque for a screw differs according

to the material and size of the screw, and the material

being screwed etc., so please use a tightening time

suitable for the screw. In particular, if a long tightening

time is used in the case of screws smaller than M8,

there is a danger of the screw breaking, so please

confirm the tightening time and the tightening torque

beforehand.

5. Work at a tightening torque suitable for the bolt

under impact

The optimum tightening torque for nuts or bolts differs

with material and size of the nuts or bolts. An

excessively large tightening torque for a small bolt

may stretch or break the bolt. The tightening torque

increases in proportion to the operaton time. Use the

correct operating time for the bolt.

6. Holding the tool

Hold the impact wrench firmly with both hands. In

this case hold the wrench in line with the bolt.

It is not necessary to push the wrench very hard.

Hold the wrench with a force just sufficient to

counteract the impact force.

7. Confirm the tightening torque

The following factors contribute to a reduction of the

tightening torque. So confirm the actual tightening

torque needed by screwing up some bolts before the

job with a hand torque wrench. Factors affecting the

tightening torque are as follows.

(1) Voltage

When the discharge margin is reached, voltage

decreases and tightening torque is lowered.

Bolt used No. of tightenings

M12 × 45 High tension bolt

Approx. 87

Screw used No. of tightenings

Wood screw ø4 × 50

Approx. 190

(Soft wood)

Machine screw M8 × 16 Approx. 500

01Eng_WH12DAF2_WE 5/14/08, 18:1113

English

14

〈

WH12DAF2

〉

(2) Operating time

The tightening torque increases when the operating

time increases. But the tightening torque does not

increase above a certain value even if the tool is

driven for a long time. (See Fig. 18 and 19)

(3) Diameter of bolt

The tightening torque differs with the diameter of the

bolt as shown in Fig. 18 and 19. Generally a larger

diameter bolt requires larger tightening torque.

(4) Tightening conditions

The tightening torque differs according to the torque

ratio; class, and length of bolts even when bolts with

the same size threads are used. The tightening torque

also differs according to the condition of the surface

of workpiece through which the bolts are to be

tightened. When the bolt and nut turn together, torque

is greatly reduced.

(5) Using optional parts (WR12DAF2)

The tightening torque is reduced a little when an

extension bar, universal joint or a long socket is

used.

Fig. 18

Tightening torque

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

Ordinary bolt

High tension bolt

M12 × 45

N

•

m

120

100

80

60

40

20

0

kgf

•

cm

1200

1000

800

600

400

200

0

Tightening torque

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Ordinary bolt

High tension bolt

M10 × 30

N

•

m

100

80

60

40

20

0

kgf

•

cm

1000

800

600

400

200

0

Tightening torque

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

High tension bolt

Ordinary bolt

M8 × 30

N

•

m

100

80

60

40

20

0

kgf

•

cm

1000

800

600

400

200

0

0123 0123 0123

(6) Clearance of the socket (WR12DAF2)

A worn or deformed hex. or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque.

Using an improper socket which does not match to

the bolt will result in an insufficient tightening torque.

(7) Tightening torque varies, depending on the battery’s

charge level. (WR12DAF2)

Fig. 21 show examples of the relationship between

tightening torque and the number of tightenings, for

WR12DAF2. As shown, tightening torque gradually

weakens with the increase in the number of

tightenings. In particular, as the torque decreases

very close to the complete discharge (“a” margin in

graph), the unit’s impact weakens, the number of

time impacts declines and tightening torque drops

off abruptly. If this occurs, check torque level, then

recharge the battery if necessary.

01Eng_WH12DAF2_WE 5/14/08, 18:1114

English

15

〈

WR12DAF2

〉

Fig. 19

Tightening torque

High tension

bolt

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

Ordinary bolt

M8 × 30

N

•

m

100

80

60

40

20

0

kgf

•

cm

1000

800

600

400

200

0

Tightening torque

Ordinary bolt

High tension

bolt

Tightening time: sec.

(Steel plate thickness

t = 10 mm)

M10 × 30

N

•

m

120

100

80

60

40

20

0

kgf

•

cm

1200

1000

800

600

400

200

0

Ordinary bolt

Tightening torque

High tension

bolt

Tightening time: sec.

(Steel plate thickness

t = 25 mm)

M12 × 45

N

•

m

140

120

100

80

60

40

20

0

kgf

•

cm

1400

1200

1000

800

600

400

200

0

0123 0123 0123

Fig. 21

〈WR12DAF2〉

Tightening torque

M12 × 45 High tension bolt

(tighening time 3 sec)

When full recharged

When completely

discharged

Number of tightenings (PCS)/charging

N

•

m

160

120

80

40

0

kgf

•

cm

1600

1200

800

400

0

a

020406080100

Nut

Fig. 20

Explanation of strength grade:

4 — Yield point of bolt: 32 kgf/mm

2

8 — Pulling strength of bolt: 40 kgf/mm

2

*The following bolt is used.

Ordinary bolt: Strength grade 4.8

High tension bolt: Strength grade 12.9

)(

Bolt

Steel plate thickness t

01Eng_WH12DAF2_WE 5/14/08, 18:1115

English

16

MAINTENANCE AND INSPECTION

1. Inspecting the driver bit (WH12DAF2)

Using a broken bit or one with a worn out tip is

dangerous because the bit can slip. Replace it.

2. Inspecting the socket (WR12DAF2)

A worn or deformed hex. or a square-holed socket

will not give an adequate tightness to the fitting

between the nut or anvil, consequently resulting in

loss of tightening torque. Pay attention to wear of a

socket holes periodically, and replace with a new one

if needed.

3. Inspecting the mounting screws

Regularly inspect all mounting screws and ensure

that they are properly tightened. Should any of the

screws be loose, retighten them immediately. Failure

to do so may result in serious hazard.

4. Cleaning of the outside

When the impact driver is stained, wipe with a soft

dry cloth or a cloth moistened with soapy water. Do

not use chloric solvents, gasoline or paint thinner, as

they melt plastics.

5. Storage

Store the impact driver in a place in which the

temperature is less than 40°C, and out of reach of

children.

6. Service parts list

A:Item No.

B:Code No.

C:No. Used

D:Remarks

CAUTION:

Repair, modification and inspection of Hitachi Power

Tools must be carried out by an Hitachi Authorized

Service Center.

This Parts List will be helpful if presented with the

tool to the Hitachi Authorized Service Center when

requesting repair or other maintenance.

In the operation and maintenance of power tools, the

safety regulations and standards prescribed in each

country must be observed.

MODIFICATIONS:

Hitachi Power Tools are constantly being improved

and modified to incorporate the latest technological

advancements.

Accordingly, some parts (i.e. code numbers and/or

design) may be changed without prior notice.

GUARANTEE

We guarantee Hitachi Power Tools in accordance with

statutory/country specific regulation. This guarantee does

not cover defects or damage due to misuse, abuse, or

normal wear and tear. In case of complaint, please send

the Power Tool, undismantled, with the GUARANTEE

CERTIFICATE found at the end of this Handling

instruction, to a Hitachi Authorized Service Center.

NOTE:

Due to HITACHI’s continuing program of reserch and

development, the specifications herein are subject to

change without prior notice.

IMPORTANT:

Correct connection of the plug

The wires of the mains lead are coloured in accordance

with the following code:

Blue: –Neutral

Brown: –Live

As the colours of the wires in the mains lead of this tool

may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire coloured blue must be connected to the terminal

marked with the letter N or coloured black.

The wire coloured brown must be connected to the

terminal marked with the letter L or coloured red.

Neither core must be connected to the earth terminal.

NOTE:

This requirement is provided according to BRITISH

STANDARD 2769: 1984.

Therefore, the letter code and colour code may not be

applicable to other markets except United Kingdom.

Information concerning airborne noise and vibration

The measured values were determined according to

EN60745 and declared in accordance with ISO 4871.

Measured A-weighted sound power level: 102 dB (A)

Measured A-weighted sound pressure level: 91 dB (A)

Uncertainty KpA: 3 dB (A).

Wear hearing protection.

Vibration total values (triax vector sum) determined

according to EN60745.

Vibration emission value

ah = 7.2 m/s

2

Uncertainty K = 1.8 m/s

2

WARNING

䡬 The vibration emission value during actual use of the

power tool can differ from the declared value

depending on the ways in which the tool is used.

䡬 To identify the safety measures to protect the operator

that are based on an estimation of exposure in the

actual conditions of use (taking account of all parts of

the operating cycle such as the times when the tool is

switched off and when it is running idle in addition to

the trigger time).

01Eng_WH12DAF2_WE 5/14/08, 18:1116

Deutsch

17

ALLGEMEINE SICHERHEITSHINWEISE FÜR

ELEKTROGERÄTE

WARNUNG

Lesen Sie sämtliche Sicherheitshinweise und

Anweisungen durch

Wenn die Warnungen und Anweisungen nicht befolgt

werden, kann es zu Stromschlag, Brand und/oder

ernsthaften Verletzungen kommen.

Bitte bewahren Sie alle Warnhinweise und Anweisungen

zum späteren Nachschlagen auf.

Der Begriff „Elektrowerkzeug“ bezieht sich in den

Warnhinweisen auf Elektrowerkzeuge mit Netz-

(schnurgebunden) oder Akkubetrieb (schnurlos).

1) Sicherheit im Arbeitsbereich

a) Sorgen Sie für einen sauberen und gut

ausgeleuchteten Arbeitsbereich.

Zugestellte oder dunkle Bereiche ziehen Unfälle

förmlich an.

b) Verwenden Sie Elektrowerkzeuge niemals an

Orten, an denen Explosionsgefahr besteht – zum

Beispiel in der Nähe von leicht entflammbaren

Flüssigkeiten, Gasen oder Stäuben.

Bei der Arbeit mit Elektrowerkzeugen kann es

zu Funkenbildung kommen, wodurch sich Stäube

oder Dämpfe entzünden können.

c) Sorgen Sie bei der Arbeit mit Elektrowerkzeugen

dafür, dass sich keine Zuschauer (insbesondere

Kinder) in der Nähe befinden.

Wenn Sie abgelenkt werden, können Sie die

Kontrolle über das Werkzeug verlieren.

2) Elektrische Sicherheit

a) Elektrowerkzeuge müssen mit passender

Stromversorgung betrieben werden.

Nehmen Sie niemals irgendwelche Änderungen

am Anschlussstecker vor.

Verwenden Sie bei Elektrowerkzeugen mit

Schutzkontakt (geerdet) niemals Adapterstecker.

Stecker im Originalzustand und passende

Steckdosen reduzieren das Stromschlagrisiko.

b) Vermeiden Sie Körperkontakt mit geerdeten

Gegenständen wie Rohrleitungen, Heizungen,

Herden oder Kühlschränken.

Bei Körperkontakt mit geerdeten Gegenständen

besteht ein erhöhtes Stromschlagrisiko.

c) Setzen Sie Elektrowerkzeuge niemals Regen oder

sonstiger Feuchtigkeit aus.

Wenn Flüssigkeiten in ein Elektrowerkzeug

eindringen, erhöht sich das Stromschlagrisiko.

d) Verwenden Sie die Anschlussschnur nicht

missbräuchlich. Tragen Sie das Elektrowerkzeug

niemals an der Anschlussschnur, ziehen Sie es

nicht damit heran und ziehen Sie den Stecker

nicht an der Anschlussschnur aus der Steckdose.

Halten Sie die Anschlussschnur von Hitzequellen,

Öl, scharfen Kanten und beweglichen Teilen fern.

Beschädigte oder verdrehte Anschlussschnüre

erhöhen das Stromschlagrisiko.

e) Wenn Sie ein Elektrowerkzeug im Freien

benutzen, verwenden Sie ein für den

Außeneinsatz geeignetes Verlängerungskabel.

Ein für den Außeneinsatz geeignetes Kabel

vermindert das Stromschlagrisiko.

f) Falls sich der Betrieb des Elektrowerkzeuges in

feuchter Umgebung nicht vermeiden lässt,

verwenden Sie eine Stromversorgung mit

Fehlerstromschutzeinrichtung (Residual Current

Device, RCD).

Durch den Einsatz einer

Fehlerstromschutzeinrichtung wird das Risiko

eines elektrischen Schlages reduziert.

3) Persönliche Sicherheit

a) Bleiben Sie wachsam, achten Sie auf das, was

Sie tun, und setzen Sie Ihren Verstand ein,

wenn Sie mit Elektrowerkzeugen arbeiten.

Benutzen Sie keine Elektrowerkzeuge, wenn Sie

müde sind oder unter Einfluss von Drogen,

Alkohol oder Medikamenten stehen.

Bei der Arbeit mit Elektrowerkzeugen können

bereits kurze Phasen der Unaufmerksamkeit zu

schweren Verletzungen führen.

b) Benutzen Sie eine persönliche Schutzausrüstung.

Tragen Sie immer einen Augenschutz.

Schutzausrüstung wie Staubmaske, rutschsichere

Sicherheitsschuhe, Schutzhelm und Gehörschutz

senken das Verletzungsrisiko bei angemessenem

Einsatz.

c) Vermeiden Sie unbeabsichtigten Anlauf. Achten

Sie darauf, dass sich der Schalter in der Aus-

(Off-) Position befindet, ehe Sie das Gerät mit

der Stromversorgung und/oder

Batteriestromversorgung verbinden, es aufheben

oder herumtragen.

Das Herumtragen von Elektrowerkzeugen mit

dem Finger am Schalter oder das Herstellen der

Stromversorgung bei betätigtem Schalter zieht

Unfälle regelrecht an.

d) Entfernen Sie sämtliche Einstellwerkzeuge

(Einstellschlüssel), ehe Sie das Elektrowerkzeug

einschalten.

Ein an einem beweglichen Teil des Elektrowerkzeugs

angebrachter Schlüssel kann zu Verletzungen führen.

e) Sorgen Sie für einen festen Stand. Achten Sie

jederzeit darauf, sicher zu stehen und das

Gleichgewicht zu bewahren.

Dadurch haben Sie das Elektrowerkzeug in

unerwarteten Situationen besser im Griff.

f) Kleiden Sie sich richtig. Tragen Sie keine lose

Kleidung oder Schmuck. Halten Sie Haar, Kleidung

und Handschuhe von beweglichen Teilen fern.

Lose Kleidung, Schmuck oder langes Haar kann

von beweglichen Teilen erfasst werden.

g) Wenn Anschlüsse für Staubabsaug- und -

sammelvorrichtungen vorhanden sind, sorgen

Sie dafür, dass diese richtig angeschlossen und

eingesetzt werden.

Durch Entfernen des Staubes können

staubbezogene Gefahren vermindert werden.

4) Einsatz und Pflege von Elektrowerkzeugen

a) Überanspruchen Sie Elektrowerkzeuge nicht.

Benutzen Sie das richtige Elektrowerkzeug für

Ihren Einsatzzweck.

Das richtige Elektrowerkzeug erledigt seine Arbeit

bei bestimmungsgemäßem Einsatz besser und

sicherer.

b) Benutzen Sie das Elektrowerkzeug nicht, wenn es

sich nicht am Schalter ein- und ausschalten lässt.

Jedes Elektrowerkzeug, das nicht mit dem

Schalter betätigt werden kann, stellt eine Gefahr

dar und muss repariert werden.

c) Stecken Sie den Stecker der Stromversorgung

oder Batteriestromversorgung vom Gerät ab,

ehe Sie Einstellarbeiten vornehmen, Zubehörteile

tauschen oder das Elektrowerkzeug verstauen.

Solche präventiven Sicherheitsmaßnahmen

verhindern den unbeabsichtigten Anlauf des

Elektrowerkzeugs und die damit verbundenen

Gefahren.

02Ger_WH12DAF2_WE 5/14/08, 18:1217

Deutsch

18

d) Lagern Sie nicht benutzte Elektrowerkzeuge

außerhalb der Reichweite von Kindern, lassen

Sie nicht zu, dass Personen das Elektrowerkzeug

bedienen, die nicht mit dem Werkzeug selbst

und/oder diesen Anweisungen vertraut sind.

Elektrowerkzeuge in ungeschulten Händen sind

gefährlich.

e) Halten Sie Elektrowerkzeuge in Stand. Prüfen

Sie auf Fehlausrichtungen, sicheren Halt und

Leichtgängigkeit beweglicher Teile,

Beschädigungen von Teilen und auf jegliche

andere Zustände, die sich auf den Betrieb des

Elektrowerkzeugs auswirken können.

Bei Beschädigungen lassen Sie das

Elektrowerkzeug reparieren, ehe Sie es benutzen.

Viele Unfälle mit Elektrowerkzeugen sind auf

schlechte Wartung zurückzuführen.

f) Halten Sie Schneidwerkzeuge scharf und sauber.

Richtig gewartete Schneidwerkzeuge mit scharfen

Schneidkanten bleiben weniger häufig hängen

und sind einfacher zu beherrschen.

g) Benutzen Sie Elektrowerkzeuge, Zubehör,

Werkzeugspitzen und Ähnliches in

Übereinstimmung mit diesen Anweisungen –

beachten Sie dabei die jeweiligen

Arbeitsbedingungen und die Art und Weise der

auszuführenden Arbeiten.

Der Gebrauch des Elektrowerkzeuges für andere

als die vorgesehenen Anwendungen kann zu

gefährlichen Situationen führen.

5) Verwendung und Pflege der Batterie

a) Laden Sie das Gerät nur mit dem vom Hersteller

empfohlenen Ladegerät auf.

Ein Ladegerät für einen speziellen Batterietyp

kann bei Verwendung mit anderen Batterien zu

Gefahren führen.

b) Verwenden Sie für das Gerät nur die speziell

empfohlenen Batterien.

Eine Verwendung von anderen Batterien kann

zu Verletzungen und Bränden führen.

c) Ist die Batterie nicht in Gebrauch, achten Sie

darauf, dass sie nicht mit metallischen

Gegenständen, beispielsweise Büroklammern,

Münzen, Schlüssel, Nägel, Schrauben in Kontakt

kommt, da diese Gegenstände einen Kurzschluss

der Anschlüsse verursachen könnten.

Ein Kurzschluss der Batterieanschlüsse kann zu

Verbrennungen oder Bränden führen.

d) Im Falle von Störungen, kann Flüssigkeit aus

der Batterie austreten. Vermeiden Sie in diesem

Fall jeglichen Kontakt. Sollten Sie dennoch mit

der Batterie in Berührung kommen, waschen

Sie die betroffene Stelle gründlich mit Wasser

ab. Ist die Flüssigkeit ins Auge geraten, suchen

Sie einen Arzt auf.

Ausgetretene Batterieflüssigkeiten können zu

Reizungen oder Verbrennungen führen.

6) Service

a) Lassen Sie Elektrowerkzeuge durch qualifizierte

Fachkräfte und unter Einsatz passender,

zugelassener Originalteile warten.

Dies sorgt dafür, dass die Sicherheit des

Elektrowerkzeugs nicht beeinträchtigt wird.

VORSICHT

Von Kindern und gebrechlichen Personen fernhalten.

Werkzeuge sollten bei Nichtgebrauch außerhalb der

Reichweite von Kindern und gebrechlichen Personen

aufbewahrt werden.

VORSICHTSMASSNAHMEN FÜR DEN AKKU-

SCHLAGSCHRAUBER

1. Dies ist ein tragbares Werkzeuggerät zum Anziehen

und Lösen von Schrauben. Es sollte nur für diesen

Zweck eingesetzt werden.

2. Bei längerem Arbeiten Ohrstöpsel verwenden.

3. Es ist äußerst gefährlich, das Gerät nur mit einer

Hand zu bedienen. Das Gerät ist beim Betrieb mit

beiden Händen festzuhalten.

4. Nachdem das Schraubstück angebracht wurde,

sollte ein wenig daran gezogen werden, um

sicherzugehen, daß es festsitzt. Wenn das

Schraubstück nicht richtig aufgesetzt wird, kann es

sich während des Betriebs lösen, was

Verletzungsgefahr bedeutet.

5 Das Schrubstück gemäß der anzuziehenden

Schraube verwenden.

6. Sollte versucht werden, mit dem Schlag-Schrauber

eine Schraube anzuziehen, wenn sich der Schlag-

Schrauber in einem Winkel zur Schraube befindet,

kann die Preßkraft des Geräts nicht voll zur Geltung

kommen; außer dem kann der Schraubenkopf

beschädigt werden. Anziehen, wenn sich der Schlag-

Schrauber mit der Schraube auf einer Linie befindet.

7. Die Batterie immer bei einer Temperatur von 0 –

40°C laden.

Laden bei einer Temperatur die niedriger als 0°C is

twird gefährliche Überladung verursachen. Die

Batterie kann nicht bei einer Temperatur über 40°C

geladen werden. Die beste Temperatur zum Laden

wäre von 20 – 25°C.

8. Das Ladegerät nicht fortlaufend laden.

Nach Beendung einer Ladung, lassen Sie das

Ladegerät ungefähr 15 Minuten ruhen bevor die

nächste Batterieladung unternommen wird.

9. Keine Fremdkörper durch das Anschlußloch der

Batterie eindringen lassen.

10. Niemals die Batterie und das Ladegerät

auseinandernehmen.

11. Niemals die Batterie kurzschließen.

Kurzschluß der Batterie verursacht eine zu große

Stromzufuhr und Überhitzung, wodurch

Durchbrennen oder Schaden beider Batterie ensteht.

12. Die Batterie nicht ins Feuer werfen.

Sie könnte dabei explodieren.

13. Darauf achten, daß keine Gegenstände durch

Belüftungsschlitze des Aufladers in das Gerät

eindringen.

Wenn Metallobjekte oder entzündliche Gegenstände

durch die Belüftungsschlitze des Aufladers

eindringen, kann dies zu elektrischen Schlägen

führen oder den Auflader beschädigen.

14. Bringen Sie die Batterie zum Geschäft, wo Sie ihn

gekauft haben sobald die Lebensdauer der Batterie

abrinnent. Die erschöpfte Batterie nicht wegwerfen.

15. Benutzung verbrauchter Batterie beschädigt den

Auflader.

VORSICHTSMASSNAHMEN FÜR DEN AKKU-

SCHLAGSCHRAUBER

1. Dies ist ein tragbares Werkzeuggerät zum Anziehen

und Lösen von Schrauben. Es sollte nur für diesen

Zweck eingesetzt werden.

2. Bei längerem Arbeiten Ohrstöpsel verwenden.

3. Es ist äußerst gefährlich, das Gerät nur mit einer

Hand zu bedienen. Das Gerät ist beim Betrieb mit

beiden Händen festzuhalten.

02Ger_WH12DAF2_WE 5/14/08, 18:1218

Deutsch

19

4. Nachprüfen, ob die Buchse gesprungen oder

gebrochen ist. Gebrochene und gesprungene

Buchsen sind gefährlich, daher die Buchse vor

Gebrauch prüfen.

5. Die Buchse mit Buchsenstift und-ring sichern. Sollte

der Buchsenstift oder-ring beschädigt sein, kann die

Buchse vom Schlag-Schraubenschlüssel

geschleudert werden, was gefährlich ist. Niemals

Buchsenstifte oder-ring verwenden, die deformiert,

abgenutzt, gesprungen oder sonstwie beschädigt

sind. Immer darauf achten, daß Buchsenstift und

-ring in der richtigen Position sind.

6. Das Anzugsdrehmoment prüfen.

Das geeignete Drehmoment für das Anziehen einer

Schraube hängt vom Material, der Art, den

Abmessungen, usw. der Schraube ab.

Außerdem hängt das von diesem Schlag-

Schraubenschlüssel erzeugte Auzugsdrehmoment

vom Material und den Abmessungen der Schraube,

für welche zeitdauer der Schlag-Schraubenschlüssel

angewendet wird, wie die Bushse angebracht ist,

usw. ab.

Das Drehmomentvariiert auch leicht, wenn die

Batterie gerade aufgeladen wurde und wenn sie

kurz vor dem Erschöpfen steht. Mit einem

Anzugsdrehmomentschlüssel nachprüfen, ob die

Schraube mit dem richtigen Drehmoment

angezogen wurde.

7. Den Schlag-Schraubenschlüssel zuerst stoppen,

wenn die Rotationsrichtung geändert werden soll.

Den Schalter immer erst freigeben und warten, bis

der Schlag-Schraubenschlüssel stoppt, bevor auf

die entgegengesetzte Rotationsrichtung geschaltet

wird.

8. Niemals die rotierenden Teile berühren.

Darauf achten, daß sich der rotierende Buchsenteil

immer in genügendem Abstand zum Körper und

den Händen befindet, da die Gefahr besteht, sich zu

schneiden oder sich in der Buchse zu verfangen.

Die Buchse sollte auch nicht direkt nach langer

kontinuierlicher Benutzuntg berührt werden, da

durch die erzeugte Hitze Verbrennungsgefhr besteht.

9. Den Schlag-Schraubenschlüssel bei Benutzung des

Universalgelenks niemals ohne Einspannung

rotieren lassen.

Wenn sich die Buchse ohne eingespannt zu sein

dreht verusacht das Universalgelenk ein wildes

Rotieren der Buchse.

Durch die schnelle Rotation der Buchse kann der

Schlag-Schrauber so stark vibrieren, daß er

losgelassen werden muß.

10. Die Batterie immer bei einer Temperatur von 0 -

40°C laden.

Laden bei einer Temperatur die niedriger als 0°C is

twird gefährliche Überladung verursachen. Die

Batterie kann nicht bei einer Temperatur über 40°C

geladen werden. Die beste Temperatur zum Laden

wäre von 20 - 25°C.

11. Das Ladegerät nicht fortlaufend laden.

Nach Beendung einer Ladung, lassen Sie das

Ladegerät ungefähr 15 Minuten ruhen bevor die

nächste Batterieladung unternommen wird.

12. Keine Fremdkörper durch das Anschlußloch der

Batterie eindringen lassen.

13. Niemals die Batterie und das Ladegerät

auseinandernehmen.

14. Niemals die Batterie kurzschließen.

Kurzschluß der Batterie verursacht eine zu große

Stromzufuhr und Überhitzung, wodurch

Durchbrennen oder Schaden beider Batterie

ensteht.

15. Die Batterie nicht ins Feuer werfen.

Sie könnte dabei explodieren.

16. Darauf achten, daß keine Gegenstände durch

Belüftungsschlitze des Aufladers in das Gerät

eindringen.

Wenn Metallobjekte oder entzündliche

Gegenstände durch die Belüftungsschlitze des

Aufladers eindringen, kann dies zu elektrischen

Schlägen führen oder den Auflader beschädigen.

17. Bringen Sie die Batterie zum Geschäft, wo Sie ihn

gekauft haben sobald die Lebensdauer der Batterie

abrinnent. Die erschöpfte Batterie nicht wegwerfen.

18. Benutzung verbrauchter Batterie beschädigt den

Auflader.

MODELL

WH12DAF2 : mit Ladegerät und Gehäuse

WR12DAF2 : mit Ladegerät und Gehäuse

02Ger_WH12DAF2_WE 5/14/08, 18:1219

La page est en cours de chargement...

Hitachi WR14DL Manuel utilisateur

Hitachi WR14DL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents