Vigo VG15973 Guide d'installation
- Catégorie
- Articles sanitaires
- Taper
- Guide d'installation
VG02007
+
/
-
I
"
27 1/4"
VIGO
■
6"
2 1/2"
1 7/8"
4 1/4"
VG02007
THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 3/8"
8 1/8"
27 1/4"
9"
3/4"
10 1/8"
9 3/4"
13 3/8"
2 3/8"
11 1/2"
2
3
Your new faucet is designed for years of trouble-free performance.
Keep it looking new by cleaning it periodically with a soft cloth. Avoid abrasive
cleaners, steel wool and harsh chemicals as these will scratch, dull, and/or
damage the finish and void the warranty.
MAINTENANCE
PACKAGE CONTENT
SPRAYER
SPRAY HOSE
HOLLOW PIN
FAUCET
ASSEMBLY
METAL SCREW
ALLEN KEY
METAL RING
RUBBER RING
METAL NUT
SPRAY HOLDER
PLASTIC
HOLDER
RING
TWO METAL
BRAIDED
HOSES
ASSEMBLY
REQUIRED TOOLS
Adjustable wrench
Allen key - supplied (to remove cartridge if needed)
Plumber's putty - optional
Pipe tape
Flat screwdrivers
SAFETY TIPS
If you use soldering for the installation of the faucet, the seats, cartridges and
washers will have to be removed before using flame. Damage caused by
improper soldering will void the warranty.
Protect your eyes with safety glasses when cutting or soldering water supply
lines.
COPPER PIN
IMPORTANT POINTS
Prior to beginning installation, turn off the cold and hot water lines and open the
hot and cold knobs on the old faucet to release pressure.
When installing your new faucet, turn the connector nuts finger-tight, then use
one wrench to anchor the fitting and a second wrench to tighten the nut.
Connections that are too tight will reduce the integrity of the system. and
potentially cause product failure which could lead to water damage.
Wrap all threaded connections with pipe tape available at your local hardware or
plumbing supply store. Always wrap in a clockwise direction.
Not all necessary supplies to install your faucet are included, however, they are
available wherever plumbing supplies are sold.
Prior to installing the faucet please FLUSH THE HOT AND COLD WATER
SUPPLY LINES that are or will be connected to the new faucet to remove scale,
solder or their impurities which could damage the faucet and potentially void the
warranty.
Do not use the independent volume controls, meaning the pot filler or sprayer, to
regulate your on and off. Always turn off the main valve at the handle. Failure to
do so can shorten the lifetime expectancy of your VIGO faucet. It can also cause
failure to the faucet and potentially cause property damage.
SPIRAL NECK
1. SHUT OFF WATER SUPPLY.
REMOVE THE OLD FAUCET AND
FLEXIBLE HOSES. CLEAN SINK
SURFACE WITH A NON ABRASIVE
CLEANER IN PREPARATION FOR
THE NEW FAUCET.
2. REMOVE METAL NUT, RUBBER RING,
AND METAL RING FROM THE FAUCET.
ATTACH METAL BRAIDED HOSES TO
THE FAUCET.
3. POSITION THE FAUCET IN THE 1 3/8"
COUNTERTOP HOLE, FROM BENEATH THE
COUNTERTOP HOLE ASSEMBLE THE
PLASTIC HOLDER, RUBBER RING, AND
METAL RING IN THE ORDER DEPICTED IN
THE DIAGRAM. THEN THREAD METAL NUT
ONTO HOLLOW PIN. TIGHTEN THE METAL
NUT UNTIL FAUCET IS SECURE.
3
2
1
METAL NUT
4. IF SPRAY HOLDER IS NOT ATTACHED,
ATTACH THE SPRAY HOLDER AND
SPRAY HOSE TO THE FAUCET AND
TIGHTEN SCREW UNTIL SPRAY HOLDER
IS SECURE.
5. FEED SPRAY HOSE THROUGH SPIRAL NECK ENSURING THE FEMALE SPRAYER
CONNECTION IS POSITIONED TOWARD TOP OF SPIRAL NECK. ATTACH MALE SPRAYER
CONNECTION TO TOP OF FAUCET BODY WITH ADJUSTABLE WRENCH UNTIL TIGHT.
SEAT SPIRAL NECK INTO SPRAY HOLDER AND FIRMLY PRESS DOWN UNTIL SECURE.
6
INSTALLATION
Installation must be done by a qualified licensed plumber.
Prior to installation please read the instructions thoroughly, confirm that all parts
are included and visually inspect the unit for any defects.
If you have any questions please contact our Technical Support Department
before proceeding with installation.
ENSURE THAT PARTS ARE
ASSEMBLED IN THE ORDER AS
DEPICTED IN DIAGRAM TO PREVENT
DAMAGE TO FAUCET AND SUPPLY
LINES.
ENSURE METAL SCREW
ALIGNS WITH NOTCH
ON WHITE WASHER IN
FAUCET BODY.
!
ENSURE THAT YOU USE PIPE TAPE
AND DO NOT OVER TIGHTEN THE
SUPPLY LINE NUTS AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
4
METAL SCREW
STABILIZES FAUCET
UNDER COUNTERTOP
!
!
SPRAYER
HOSE
CONNECTION
WASHER FLOW
RESTRICTER
SPRAY WASHER
WRENCH
5. FEED SPRAY HOSE THROUGH SPIRAL NECK ENSURING THE FEMALE SPRAYER
CONNECTION IS POSITIONED TOWARD TOP OF SPIRAL NECK. ATTACH MALE SPRAYER
CONNECTION TO TOP OF FAUCET BODY WITH ADJUSTABLE WRENCH UNTIL TIGHT.
SEAT SPIRAL NECK INTO SPRAY HOLDER AND FIRMLY PRESS DOWN UNTIL SECURE.
7. ATTACH THE FEMALE
CONNECTIONS OF THE METAL
BRAIDED HOSES TO THE COLD
AND HOT WATER SUPPLY .
8. AFTER INSTALLATION IS COMPLETE, TURN ON THE WATER SUPPLY AND ALLOW BOTH
HOT AND COLD WATER TO RUN SEPARATELY FOR AT LEAST TWO MINUTES EACH. WHILE
WATER IS RUNNING, CHECK FOR LEAKS. IT IS IMPORTANT TO VIEW THE CONNECTIONS AT
THE MALE AND FEMALE FLEXIBLE HOSE CONNECTIONS. IF LEAKS ARE DETECTED, REFER
BACK TO THE INSTRUCTIONS AND ADJUST ACCORDINGLY. TIGHTENING NUTS SLIGHTLY
MAY STOP ANY MINOR LEAKS.
7
6. ATTACH SPRAYER TO FEMALE CONNECTION OF SPRAYER
HOSE BY HAND AND TIGHTEN UNTIL SECURE.
ENSURE THAT YOU USE PIPE TAPE
AND ADJUSTABLE WRENCH, DO NOT
OVER TIGHTEN AS THIS COULD
CAUSE PRODUCT FAILURE LEADING
TO WATER DAMAGE.
VISUALLY INSPECT MALE AND
FEMALE SPRAYER HOSE
CONNECTIONS AND FAUCET BODY TO
ENSURE THE WASHERS AND FLOW
RESTRICTORS ARE PRESENT.
MISSING OR DAMAGED WASHERS
AND FLOW RESTRICTORS COULD
CAUSE PERSONAL INJURY OR WATER
DAMAGE.
!
!
USE WASHER WITH SCREEN AT CONNECTION POINT BETWEEN
SPRAYER AND SPRAYER HOSE. THIS WILL STOP DEBRIS FROM
TRAVELING INTO THE SPRAYER HEAD AND EFFECTING ITS
FUNCTIONALITY. PLEASE NOTE THAT THE SCREEN WASHER
WILL NEED TO BE REMOVED AND CLEANED APPROXIMATELY
ONCE EVERY 3 MONTHS TO AVOID BUILD UP AND LOW WATER
FLOW.
!
4
TROUBLESHOOTING
PROBLEM POTENTIAL CAUSE CORRECTIVE ACTION
1 - Leaks from Handle
2 - Insufficient Flow Rate
3 - Leak at Connection Points
4 - Loose Spiral Neck
5 - Loose Faucet Body
PARTS LIST - For any parts needed but not shown, please contact Vigo Technical Support
PART
TOLL FREE: (866) 591 - 7792
E-Mail: [email protected]
www.vigoindustries.com
PART #
SUPPLY DATE INDICATOR (INTERNAL USE ONLY)
1.A - Cartridge unseated
1.B - Cartridge defective
2 - Clog in supply hose / line
3.A - Sprayer hose not tight
3.B - Flexible hose leaking at body or connection point
4 - Metal screw is not locked into internal white washer hole
location
5 - Metal nut became loose
3.A - Remove spiral neck by loosing the metal screw and pulling
up on the spiral neck exposing the spray hose. Make sure the
washer is seated properly and retighten with an adjustable
wrench.
2 - Remove sprayer or supply line and flush lines
1.A - Remove cartridge from housing, wash thoroughly with
hot water and reseat in housing.
1.B - Contact VIGO Technical Support for replacement.
4 - Loosen metal screw, lift off the spiral neck and reseat making
sure to thread the metal screw into the white washer housing.
3.B - Tighten hoses. If this does not resolve the issue, remove
the flexible hose and rethread, checking to make sure the
connection is secure. Make sure to use pipe tape.
5 - From under the counter, use an adjustable wrench and
tighten the metal nut to the hollow pipe. Make sure the faucet is
perpendicular to the counter.
W78021
Sprayer
W
W
74017
Spray hose
W
78064A
W
W
W
W
78064CPot Filler Set Screw
W
78027C
Handle
W
78027A
78027BHandle Set Screw
74040
74020
Metal Braided hose
78064B
Sedal Cartridge
Handle Lever
Pot Filler Handle Lever
Pot Filler Handle
W78065
Pot Filler Cartridge
Sprayer Washer
W74008
Diverter Cartridge
W
78066
Black Washer with Screen W
74010
VIGO INDUSTRIES, LLC ("VIGO")
FAUCET LIMITED LIFETIME WARRANTY
EFFECTIVE APRIL 1, 2013
VIGO offers the following limited warranty on each of its Faucet products (the "Product") and the components thereof. This warranty extends only to the original owner
for personal household use. For commercial uses, additional limitations apply.
VIGO warrants the structure of the Product to be free from defects in workmanship and materials under normal use and service for the period commencing from the
initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer, through the lifetime of the original owner or end-user.
VIGO warrants the cartridge component of the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years
from the initial date of purchase by the owner, contractor, or builder, from VIGO or an authorized VIGO dealer.
VIGO warrants the diverter component and/or pot filler components of the product to be free from defects in workmanship and materials under normal use and service
for a period of two (2) years from the initial date of purchase by the owner or end-user, contractor, or builder from VIGO or an authorized VIGO dealer.
Subject to the Warranty Service provision below, any product reported to the authorized dealer or to VIGO as being defective within the warranty period will be repaired
or replaced (with a product of equal value) at the option of VIGO. This warranty extends to the original owner and is not transferable to a subsequent owner.
Neither the distributor, authorized VIGO dealer, nor any other person has been authorized to make any affirmation, representation, or warranty other than those
contained in this warranty. Any affirmation, representation, or warranty other than those contained in this warranty shall not be enforceable against VIGO or any other
person.
VIGO reserves the right to modify this warranty at any time, it being understood that such modifications will not alter the warranty conditions applicable at the time of
sale of the products in question.
Limitations
This warranty shall not apply to instances of incorrect operating procedures, breakages, or damages caused by fault through improper installation, carelessness, abuse,
misuse, misapplication, improper maintenance, or alteration of the Product, as well as chemical or natural corrosion, accident, fire, flood, an act of God, or any other
casualty. Avoid abrasive cleaners, steel wools, and harsh chemicals as these will scratch, damage, and / or dull the product and / or finish and void this warranty. The
owner of the Product covered by the present warranty is entirely responsible for its proper installation and any applicable plumbing or electrical wiring. VIGO neither
installs nor supervises the installation nor hires a contractor for this purpose; consequently, VIGO cannot be held responsible for any default, breakage, or damages
caused thereby or resulting thereof, either directly or indirectly.
The owner must provide access to the components of the Product as described in the installation guide so that VIGO can execute the warranty specified herein. If such
access is not available, all expenses to provide said access will be the responsibility of the owner.
This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by VIGO and all applicable rules, regulations,
and legislation pertaining to such installations.
This warranty does not apply unless the VIGO Product is installed by fully insured licensed professionals. Vigo strongly recommends that such licensed professionals
have experience in the installation of bathroom and kitchen products. [Installation of certain products, including without limitation glass products (i.e., shower doors and
glass sinks) by an inexperienced person may result in product failure including, but not limited to, glass breakage which could result in personal injury or death.]
VIGO is not liable for personal injuries or deaths to any persons or for any direct, special, incidental, or consequential damage, loss of time, loss of profits,
inconvenience, incidental expenses, labor or material charges, or any other costs resulting from the use of the product or equipment or pertaining to the application of
the present warranty, or resulting from the removal or replacement of any product or element or part covered by this warranty.
EXCEPT AS OTHERWISE PROVIDED ABOVE, VIGO MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE OR COMPLIANCE WITH ANY CODE.
In any case, VIGO cannot be held liable for any amount over and above the purchase price paid for the Product by the owner/end-user, contractor, or builder.
Commercial Limitations
In addition to the above conditions and limitations, the warranty period for products installed for commercial applications or used in commercial ventures is one (1) year
from the initial date of purchase by the owner, contractor, or builder from an authorized dealer. VIGO is not responsible for loss of use or profit under any circumstances.
If the product is used as a display, the warranty period begins from the date of purchase. This warranty gives the owner specific legal rights. The owner may also have
other rights which can vary from one state or province to another.
Warranty Service
In order to obtain service provided under this warranty during regular business hours, contact the dealer or distributor who sold the unit, or contact VIGO directly. VIGO
will provide the warranty service described above when the following conditions have been met: the failure is of the nature or type covered by the warranty; the user has
informed an authorized VIGO Agent or VIGO's warranty service department representative of the nature of the problem during the warranty period; conclusive evidence
(e.g., proof of purchase or installation) is provided to the foregoing by the user proving that the failure occurred or was discovered within the warranty period; an
authorized independent service person or company representative has been permitted to inspect the product during regular business hours within a reasonable time
after the problem was reported by the user. Vigo's warranty obligation shall be discharged upon tender of replacement or repair. The customer's refusal to accept the
tender terminates VIGO's warranty obligations.
Certification may be ended by VIGO or certification agencies without notice.
5
1
* = +/- 1"
ESPECIFICACIONES DEL GRIFO
Grifo de cocina con rociador extensible
Modelo VG02007
ORIFICIO GRIFO PICO
VG02007 1 3/8" 27 1/4" 9"
DIMENSIONES
MODELO VG02007
LISTA DE CONTENIDO
9"
27 1/4" *
8 1/8"
NOTA: Todos los grifos cumplen con CEC 2016 regulaciones. Si
usted tiene preguntas acerca de su flujo de agua, por favor
escriba [email protected].
6"
2 1/2"
1 7/8"
4 1/4"
VG02007
8 1/8"
27 1/4"
3/4"
10 1/8"
9 3/4"
13 3/8"
2 3/8"
9"
11 1/2"
2
3
CONTENIDO DE LA CAJA
ROCIADOR
MANGUERA DEL ROCIADOR
PASADOR
HUECO
CONJUNTO
DEL GRIFO
LLAVE ALLEN
ARO DE GOMA
SOPORTE DEL ROCIADOR
SOPORTE
ARO
DOS
MANGUERAS
TRENZADAS
MONTAJE
PASADOR DE
COBRE
Cuello en espiral
1. CIERRE EL SUMINISTRO DE AGUA.
RETIRE EL GRIFO VIEJO Y LAS
MANGUERAS FLEXIBLES. LIMPIE LA
SUPERFICIE DEL LAVABO CON UN
LIMPIADOR NO ABRASIVO PARA
COLOCAR EL GRIFO NUEVO.
DEL GRIFO. ACOPLE LAS MANGUERAS
3. COLOQUE EL GRIFO EN EL ORIFICIO DE
ORIFICIO DE LA MESADA, ENSAMBLE EL
INDICA EL DIAGRAMA. LUEGO, ENROSQUE
HASTA ASEGURAR EL GRIFO.
3
2
1
4. SI EL SOPORTE DEL ROCIADOR NO
DEL ROCIADOR Y LA MANGUERA DEL
ROCIADOR AL GRIFO Y AJUSTE EL
TORNILLO HASTA ASEGURAR EL
SOPORTE DEL ROCIADOR.
SUPERIOR DEL CUERPO DEL GRIFO Y AJUSTE CON UNA LLAVE DE AJUSTE. ASIENTE EL
CUELLO EN ESPIRAL EN EL SOPORTE DEL ROCIADOR Y PRESIONE FIRMEMENTE HACIA
ABAJO HASTA QUE QUEDE ESTABLE.
6
7. ACOPLE LAS CONEXIONES
HEMBRA DE LAS MANGUERAS
CALIENTE.
MIENTRAS CORRE EL AGUA, VERIFIQUE SI HAY FUGAS. ES IMPORTANTE REVISAR LAS
UNIONES EN LAS CONEXIONES MACHO Y HEMBRA DE LAS MANGUERAS FLEXIBLES. EN
CASO DE DETECTAR FUGAS, CONSULTE NUEVAMENTE LAS INSTRUCCIONES Y AJUSTE
TUERCAS LEVEMENTE.
7
MANGUERA DEL ROCIADOR A MANO Y AJUSTE HASTA QUE
QUEDE FIRME.
ENSAMBLE LAS PIEZAS EN EL ORDEN
QUE INDICA EL DIAGRAMA A FIN DE
ALINEE EL TORNILLO
ARANDELA BLANCA EN
EL CUERPO DEL GRIFO.
!
DE SUMINISTRO EN EXCESO, YA QUE
POR EL AGUA.
4
UNA LLAVE DE AJUSTE. NO AJUSTE
CAUSAR FALLAS EN EL PRODUCTO
AGUA.
METAL SCREW
ESTABILIZA EL GRIFO
DEBAJO DE LA MESADA
INSPECCIONE VISUALMENTE LAS
CONEXIONES MACHO Y HEMBRA DEL
ROCIADOR Y EL CUERPO DEL GRIFO Y
VERIFIQUE QUE LAS ARANDELAS Y LOS
LAS ARANDELAS Y LOS LIMITADORES DE
POR EL AGUA.
!
!
!
!
ROCIADOR
MANGUERA
ARANDELA LIMITADOR
DE FLUJO
ARANDELA DEL
ROCIADOR
MANTENIMIENTO
HERRAMIENTAS NECESARIAS
Llave de ajuste
Llave Allen (se suministra) para retirar el cartucho, si fuera necesario
Destornilladores planos
CONSEJOS DE SEGURIDAD
Si instala el grifo mediante soldadura, los asientos, los cartuchos y las arandelas
seguridad.
PUNTOS IMPORTANTES
para sujetar el accesorio y una segunda llave para apretar la tuerca.
horario.
Si bien no se incluyen todos los elementos necesarios para instalar el grifo, estos
No utilice los controles de volumen independientes para regular el encendido y
incluidas todas las piezas e inspeccione visualmente la unidad a fin de descartar
defectos.
LLAVE
INGLESA
!
CABEZA PULVERIZADOR Y EFECTUANDO SU FUNCIONALIDAD. TENGA EN CUENTA
FLUJO DE AGUA BAJO.
4
PROBLEMA POSIBLE CAUSA
1 - Fugas en la palanca
2 - Caudal insuficiente
3 -
5 - Grifo flojo
4 - Cuello en espiral flojo
2
1.B - El cartucho es defectuoso
1.A -
interna blanca
5 - Por debajo de la mesada, utilice una llave de ajuste y ajuste la
perpendicular a la mesada.
3.B - Ajuste las mangueras. Si el problema persiste, retire la
de la arandela blanca.
1.A - Retire el cartucho de la carcasa, lave completamente con
agua caliente y vuelva a colocar en la carcasa.
de Vigo para el reemplazo
2
levante el cuello en espiral hasta dejar expuesta la manguera del
vuelva a ajustar con una llave de ajuste.
: (866) 591 - 7792
: [email protected]
www.vigoindustries.com
W78021
W
78021
W74017
W78064A
W78064A
W
W
W78064C
W78064C
W78027C
W
W78027A
W78027A
W
78027B
W
78027B
W
74040
W
74020
78027C
78064B
78064B
PIEZA
LISTA DE PIEZAS -
PIEZA #
INDICADOR DE FECHA (SOLO PARA USO INTERNO)
Rociador
Rociador
Manguera del rociador
Palanca
Palanca
Cartucho Sedal
Palanca
Palanca
W78065Cartucho de Relleno de Olla
Lavadora Pulverizador 74008
W
Cartucho Desviador
78066
W
Lavadora Negro con Pantalla
W
74010
5
VIGO INDUSTRIES, LLC ("VIGO")
JA PARTIR DEL 1 DE ABRIL DE 2013
partir de la fecha inicial de compra por parte del propietario, contratista o constructor a VIGO o a un distribuidor autorizado de VIGO, de por vida para el propietario original o
usuario final.
de VIGO
propietario.
Limitaciones
leyes correspondientes a este tipo de instalaciones.
de vidrio (por ejemplo, puertas de duchas y lavabos de cristal) por parte de una persona sin experiencia puede resultar en defectos del producto, incluidos, entre otros, la
constructor.
Limitaciones comerciales
1
9"
27 1/4" *
* = +/- 1"
8 1/8"
TROU ROBINET BEC
VG02007 1 3/8" 27 1/4" 9"
DIMENSIONS
LISTE D'EMBALLAGE
de la CEC de 2016. Si vous avez des questions au sujet de votre
6"
2 1/2"
1 7/8"
4 1/4"
VG02007
8 1/8"
27 1/4"
3/4"
10 1/8"
9 3/4"
13 3/8"
2 3/8"
9"
11 1/2"
2
3
CONTENU DE L'EMBALLAGE
VAPORISATEUR
TUYAU DU VAPORISATEUR
AXE CREUX
ENSEMBLE
ROBINET
ANNEAU EN
CAOUTCHOUC
SUPPORT DU VAPORISATEUR
SUPPORT EN
PLASTIQUE
ANNEAU
DEUX
TUYAUX
AXE EN CUIVRE
3
2
1
6
7
ASSUREZ-VOUS QUE LA VIS
AVEC L'ENTAILLE SUR LA
RONDELLE BLANCHE DANS
LE CORPS DU ROBINET
!
4
!
!
!
!
annuler la garantie.
ENTRETIEN
OUTILS REQUIS
Mastic de plombier - facultatif
Ruban pour tuyau
Tournevis plats
par une mauvaise soudure annuleront la garantie.
conduites d'alimentation d'eau.
POINTS IMPORTANTS
Avant de commencer l'installation, fermez les conduites d'eau froide et chaude et
dans votre quincaillerie ou magasin de plomberie local. Toujours enrober dans le
fournitures de plomberies sont vendues.
Avant d'installer le robinet veuillez PURGER LES CONDUITES D'ALIMENTATION
robinet et potentiellement annuler la garantie.
INSTALLATION
Si vous avez des questions, veuillez communiquer avec le Service de Soutien
ASSEMBLAGE
1. COUPEZ L'ALIMENTATION EN EAU.
ENLEVEZ L'ANCIEN ROBINET ET LES
TUYAUX FLEXIBLES. NETTOYEZ LA
NOUVEAU ROBINET.
3. PLACEZ LE ROBINET DANS LE TROU DE 1 3/8"
DESSOUS DU TROU DE COMPTOIR ASSEMBLEZ
LE SUPPORT EN PLASTIQUE, L'ANNEAU EN
4. SI LE SUPPORT DU VAPORISATEUR N'EST
VAPORISATEUR ET LE TUYAU DU
VAPORISATEUR AU ROBINET ET SERREZ LA VIS
FERMEMENT VERS LE BAS POUR BIEN FIXER.
7. ATTACHEZ LES CONNEXIONS
FROIDE ET CHAUDE.
DOMMAGES AU ROBINET ET AUX
CONDUITES D'ALIMENTATION.
ASSUREZ-VOUS D'UTILISER DU
RUBAN POUR TUYAU ET NE
DE LA CONDUITE
D'ALIMENTATION PUISQUE CELA
POURRAIT CAUSER UNE
ASSUREZ-VOUS D'UTILISER DU
AJUSTABLE, NE SERREZ PAS TROP
PUISQUE CELA POURRAIT CAUSER
STABILISE LE ROBINET
SOUS LE DESSUS DE COMPTOIR
ET FEMELLE DU TUYAU DU VAPORISATEUR ET LE
CORPS DU ROBINET POUR VOUS ASSURER QUE
CONNEXION
TUYAU
VAPORISATEUR
RONDELLE
RONDELLE DU
VAPORISATEUR
!
4
tuyau flexible et raccorder de nouveau, en s'assurant que la
2 - Enlever le vaporisateur ou la conduite d'alimentation et purger les
conduites
1.B - Communiquer avec le Soutien technique de Vigo pour un
remplacement.
de l'eau chaude et bien asseoir dans le logement.
perpendiculaire au comptoir.
rondelle blanche.
vaporisateur. S'assurer que la rondelle est bien assise et resserrer
MESURE CORRECTIVECAUSE POTENTIELLE
3.B - Fuite du tuyau flexible au niveau du corps ou du point de
connexion
2 - Encrassement dans tuyau/conduite d'alimentation
1.A - Cartouche non assise
trou de la rondelle blanche
3 - Fuite aux points de connexion
SANS FRAIS : (866) 591 - 7792
Courriel : [email protected]
www.vigoindustries.com
W78021
W
78021
W74017
W78064A
W78064A
W
W
W78064C
Vis Ensemble remplisseur
W78064C
W78027C
W
W78027A
W78027A
W
78027B
W
78027B
W
74040
W
74020
78027C
78064B
78064B
Vis Ensemble remplisseur
INDICATEUR DATE D'APPROVISIONNEMENT (USAGE INTERNE SEULEMENT)
Tuyau du vaporisateur
Vaporisateur
Vaporisateur
Cartouche Sedal
W78065
Cartouche de remplisseur de pot
74008
W
Cartouche D'inversion
78066
W
W
74010
5
VIGO INDUSTRIES, LLC ("VIGO")
EN VIGUEUR LE 1er AVRIL 2013
original pour usage domestique personnel. Des restrictions additionnelles s'appliquent aux utilisations commerciales.
de la vente des produits en cause.
Restrictions
verre qui pourrait causer des blessures corporelles ou la mort.]
constructeur.
Restrictions commerciales
Service sous garantie
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
Vigo VG15973 Guide d'installation
- Catégorie
- Articles sanitaires
- Taper
- Guide d'installation
dans d''autres langues
- English: Vigo VG15973 Installation guide
- español: Vigo VG15973 Guía de instalación
