GE Profile GTS18DCPLBB Le manuel du propriétaire

Marque: GE Profile

Modèle: GTS18DCPLBB

Catégorie: Frigos

Taper: Le manuel du propriétaire

GEAppliances.com
Refrigerators
Top-Freezer
197D3354P013     49-60511-1    05-09 JR
Safety Instructions . . . . . . . . . . . .2–3
Operating Instructions
Additional Features . . . . . . . . . . . . . . . . .6
Automatic Icemaker  . . . . . . . . . . . . . . . .7
Controls  . . . . . . . . . . . . . . . . . . . . . . . . . .4
Crispers and Pans  . . . . . . . . . . . . . . . . . .6
Dispenser  . . . . . . . . . . . . . . . . . . . . . . . . .7
Shelves and Bins  . . . . . . . . . . . . . . . . . . .5
Water Filter  . . . . . . . . . . . . . . . . . . . . . . .4
Care and Cleaning
Care and Cleaning  . . . . . . . . . . . . . . .8, 9
Replacing the Light Bulbs  . . . . . . . . . . .9
Installation Instructions
Preparing to Install 
the Refrigerator . . . . . . . . . . . . . . . . . . .10
Reversing the Door Swing  . . . . . . .14–18
Water Line Installation  . . . . . . . . . .11–14
Troubleshooting Tips  . . . . . . .19–21
Normal Operating Sounds  . . . . . . . . . .19
Consumer Support
Consumer Support . . . . . . . . .Back Cover
Performance Data Sheet  . . . . . . . . . . .27
Product Registration 
for Canadian Customers . . . . . . . . .23, 24
State of California Water 
Treatment Device Certificate  . . . . . . . .28
Warranty for 
Canadian Customers . . . . . . . . . . . . . . .25
Warranty for U.S. Customers  . . . . . . . .26
Réfrigérateurs
Congélateur supérieur
Refrigeradores
Congelador superior
Model 18
Manuel d’utilisation 
et d’installation
Owner’s Manual and
Installation Instructions
Manual del propietario 
e instalación
La section française commence à la page 29
La sección en español empieza en la página 53 
Nota al instalador – Asegúrese de
dejar estas instrucciones con el consumidor.
Nota al consumidor – Conserve 
estas instrucciones para referencia futura.
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on the gray label 
on the left side, near the top of the
refrigerator compartment.
Refrigerators
Top-Freezer
Note to Installer – Be sure to leave
these instructions with the Consumer.
Note to Consumer – Keep these
instructions for future reference.
Note à l’installateur – Assurez-vous de
laisser ces instructions au consommateur.
Note au consommateur – Conservez
ces instructions pour référence future.
Instructions de sécurité . . . .29–30
Instructions de fonctionnement
Bacs à légumes  . . . . . . . . . . . . . . . . .33
Caractéristiques additionnelles  . . . .33
Clayettes et bacs  . . . . . . . . . . . . . . . .32
Distributeur . . . . . . . . . . . . . . . . . . . .34
Filtre à eau  . . . . . . . . . . . . . . . . . . . .31
Machine à glaçons automatique  . . .34
Réglages  . . . . . . . . . . . . . . . . . . . . . .31
Soins et nettoyage
Remplacement des 
ampoules électriques  . . . . . . . . . . . .36
Soins et nettoyage . . . . . . . . . . . .35, 36
Instructions d’installation
Installation de la 
conduite d’eau  . . . . . . . . . . . . . .38–41
Inversion du sens 
d’ouverture des portes  . . . . . . . .41–45
Préparation à l’installation 
du réfrigérateur  . . . . . . . . . . . . . . . .37
En cas de panne  . . . . . . . . .46–49
Bruits normaux 
de fonctionnement . . . . . . . . . . . . . .46
Soutien au consommateur
Feuillet de données relatives à la 
performance de la cartouche . . . . . . .51
Garantie . . . . . . . . . . . . . . . . . . . . . . .50
Soutien au consommateur . . . . . . . .52
Información de seguridad  . . .53–54
Instrucciones de operación
Características adicionales  . . . . . . . . . . .57
Controles  . . . . . . . . . . . . . . . . . . . . . . . . .55
Dispensador  . . . . . . . . . . . . . . . . . . . . . . .58
Estantes y compartimientos . . . . . . .56 –57
Filtro de agua . . . . . . . . . . . . . . . . . . . . . .55
Gavetas de almacenamiento  . . . . . . . . .57
Máquina de hielos automática  . . . . . . .58
Cuidado y limpieza
Cómo reemplazar las bombillas  . . . . . .60
Cuidado y limpieza  . . . . . . . . . . . . . .59–60
Instrucciones para la instalación
Cómo invertir el vaivén de 
la puerta  . . . . . . . . . . . . . . . . . . . . . . .65–69
Instalación de la tubería 
del agua  . . . . . . . . . . . . . . . . . . . . . . .62–65
Preparación para instalar 
el refrigerador  . . . . . . . . . . . . . . . . . . . . .61
Consejos para la solución 
de problemas  . . . . . . . . . . . . . . .70–74
Sonidos normales de operación  . . . . . .70
Soporte al consumidor
Hoja de datos de funcionamiento  . . . .78
Garantía  . . . . . . . . . . . . . . . . . . . . . . . . . .77
Soporte al consumidor . . . . . . . . . . . . . .79
Escriba aquí el modelo y el número 
de serie:
Modelo  # ________________________________
Serie # __________________________________
Encuentre estos números en la etiqueta gris en
el lado izquierdo, cerca de la parte superior
del compartimiento del refrigerador. 
Écrivez ici le numéro de modèle et le numéro de
série :
Modèle # ______________________________
Série # ________________________________
Vous trouverez ces numéros sur l’étiquette grise
située à gauche, près du haut du compartiment
réfrigérateur.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■ This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■ Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■ Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■ Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■ In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating element

located on the bottom of the icemaker. Do not

place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■ Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small. Be careful

closing doors when children are in the area.

■

■ Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■ Setting either or both controls (some models only

have one control) to the

0 (off)

position does not

remove power to the light circuit.

■

■ Do not refreeze frozen foods which have

thawed completely.

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they will

sit for “just a few days.” If you are getting rid of

your old refrigerator, please follow the instructions

below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■ Take off the doors.

■ Leave the shelves in place so that children

may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation Instructions

GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to

minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

The refrigerator should always be plugged into its

own individual electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

About the controls on the refrigerator.

Control Settings

Initially, set the control(s) at 5 (some models have

only one control). Allow 24 hours for the temperature

to stabilize.

Several adjustments may be required. Adjust the

control(s) one increment at a time and allow 12 hours

after each adjustment for the refrigerator to reach the

temperature you have set.

Setting the refrigerator control to 0 stops cooling in

both the freezer and refrigerator compartments but

does not shut off electrical power to the refrigerator.

The freezer control (on some models) has no effect on electrical power to the refrigerator.

Control settings will vary based on personal preferences, usage and operating conditions, and may require

more than one adjustment. Factors that affect temperature include the amount of food in the refrigerator or

freezer, the frequency of door opening and the temperature of food when it is placed in the refrigerator.

Installing the Filter

Cartridge

If you are replacing the

cartridge, first remove the

old one. To open the

cartridge cover, push in

where indicated and the

cover will drop down.

Remove the cartridge by

slowly rotating it to the left.

A small amount of water

may drip down.

CAUTION:

If air

has been trapped in the system,

the filter cartridge may be

ejected as it is removed. Use

caution when removing.

Apply a month and year

sticker to the new cartridge

to remind you to replace it

six months

Position the cartridge

inside the cartridge holder

and slowly rotate the

cartridge to the right until

it stops. When the

cartridge is properly

installed, you will feel it

“click” as it locks into

place. The blade on the

end of the cartridge

should be positioned

vertically.

Do not

overtighten

Close the cartridge cover.

Run water from the

dispenser for 3 minutes

(about 1

⁄2 gallons) to clear

the system and prevent

sputtering. See

To Use the

Dispenser

section.

NOTE:

A newly-installed water

filter cartridge may

cause water

to spurt

from the dispenser.

About the water filter. (on some models)

Water Filter Cartridge

The water filter cartridge is

located inside the cartridge

holder in the back upper right

corner of the refrigerator

compartment.

NOTE:

Some models ship with the

filter bypass plug in place of the

filter cartridge. The filter bypass plug needs to be removed before

the filter cartridge is installed. Keep the filter bypass plug for

future use.

When to Replace the Filter

The filter cartridge should be replaced every

six months

or earlier

if the flow of water to the icemaker and dispenser decreases.

Filter Bypass Plug

You must use the filter bypass plug when

a replacement filter cartridge is not available. The dispenser and

the icemaker will not operate without the filter or filter bypass

plug.

Replacement Filters

To order additional filter cartridges in the United States, visit our

Website, GEAppliances.com, or call GE Parts and Accessories,

1.800.661.1616.

Filter Model GSWF

Customers in Canada should consult the yellow pages for

the nearest Mabe Service Center

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

(on some models)

Consumer Support

Troubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

About the shelves and bins. GEAppliances.com

Not all features are on all models.

Rearranging the Shelves

Refrigerator Compartment

Freezer Compartment

To remove:

Lift and slide left.

Rotate up and out.

To replace:

Holding the shelf diagonally,

insert the left end of the shelf

into the center of the shelf

supports on the side wall.

Insert the right end of the

shelf into the shelf supports

on the side wall. Rest each

end of the shelf on the

bottom of the shelf supports.

To remove:

Tilt the shelf up at the front.

Lift the shelf up at the back

and bring the shelf out.

To replace:

While tilting the shelf up, insert

the top hook at the back of the

shelf in a slot on the track.

Lower the front of the shelf until

the bottom of the shelf locks into

place.

Some models have wire shelves that

can be adjusted in the same manner.

Non-Adjustable Shelves on the Door

Detachable shelves deepen and enclose fixed

door shelves, providing more storage room and

greater storage flexibility.

To remove:

Lift the shelf straight up; then pull out.

To replace:

Engage the shelf extender in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door (on some models)

To remove:

Lift bin straight up; then pull out.

To replace or relocate:

Engage the bin in the molded supports

of the door and push down. Bin will lock

in place.

Tab

Opening

Front bar

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you to reach

items stored behind others. The special edges

are designed to help prevent spills from dripping

to lower shelves.

NOTE: The shelves are shipped with tape on the

back. Remove this tape before attempting to remove

the shelf.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the tabs

are above the shelf frame.

Continue pulling the shelf forward until it

can be lifted out and removed.

To replace:

Place the rear of the shelf on the shelf frame

just behind the front bar.

Slide the shelf back until the tabs are above

the openings.

Lower the shelf so that the tabs go into the

openings; then slide the shelf all the way in.

Make sure that the shelf sits flat after reinstallation and

doesn’t move freely from side to side.

Make sure you push the shelves all the way in before you

close the door.

Freezer Tilt-Out Bin (on some models)

Push the button as you tilt out the bin.

To remove:

Hold the sides of the bin and

lift it straight up; then pull out.

To replace:

Engage the ends of the bin

in the molded supports on the door and

push down. It will lock in place.

NOTE: Do not overload the bin.

Adjustable bins can easily be carried from refrigerator to work area.

NOTE: Bins for the refrigerator and freezer doors are different sizes and are not interchangeable.

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH

setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the

LOW

setting to

provide lower humidity levels recommended for

most fruits.

Snack Pan (on some models)

This pan can be moved to

the most useful location for

your family’s needs.

Fruit and Vegetable Crispers

Excess water that may

accumulate in the bottom

of the drawers or under the

drawers should be wiped dry.

About the crispers and pans.

Not all features are on all models.

Removing the glass cover

About the additional features.

Not all features are on all models.

ShelfSaver

™

Rack

This slide-out rack holds twelve cans of soda

or two wine/water bottles (lengthwise).

Can be removed for cleaning.

To remove,

slide the rack out to the

stop

position, lift the rack up and past the

stop

and lift out.

Crisper Removal

Unload the bottom shelf before attempting to

remove the storage drawers.

To Remove:

Lift the drawers up slightly while pulling

them past the

stop

location.

If the door prevents you from taking out

the drawers, first try to remove the door

bins. If this does not offer enough

clearance, the refrigerator will need to

be rolled forward until the door opens

enough to slide the drawers out. In some

cases, when you roll the refrigerator out,

you will need to move the refrigerator

to the left or right as you roll it out.

To remove the glass cover:

Remove the glass, then the frame. When

replacing the glass, push the front edge

firmly into the frame.

Lift the back up off of its supports, slide it

backward, tilt it and take it out.

To remove the frame:

Lift the front of the frame, pull it forward,

tilt it and take it out.

Consumer Support

Troubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

About the automatic icemaker. GEAppliances.com

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Automatic Icemaker (on some models)

The icemaker will produce approximately

3 to 3

⁄2 lbs. of ice in a 24-hour period,

depending on the freezer compartment

temperature, room temperature, number

of door openings and other use conditions.

If the refrigerator is operated before the

water connection is made to the icemaker,

move the feeler arm to the

STOP

(up)

position.

When the refrigerator has been connected

to the water supply, move the feeler arm to

the

(down) position.

The icemaker will fill with water when it

cools to 15°F. A newly-installed refrigerator

may take 12 to 24 hours to begin making

ice cubes.

Once the icemaker starts to make ice,

it may take up to 48 hours to fill the bin,

depending on the temperature settings

and number of door openings.

You will hear a buzzing sound each time

the icemaker fills with water.

Throw away the first few batches of ice

to allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale, shrink or

fuse together.

On power switch models, the green power

light will blink if ice cubes get stuck in the

icemaker. To correct this, set the power

switch to

O (off)

and remove the cubes.

Set the power switch to

I (on)

to restart the

icemaker. After the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

Icemaker accessory kit:

If your refrigerator did not already come

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for the

specific icemaker kit needed for your model.

To Use the Dispenser (on some models)

The water dispenser is located on the left

wall inside the refrigerator compartment.

To dispense water:

Hold the glass against the recess.

Push the water dispenser button.

Hold the glass underneath the

dispenser for 2–3 seconds after

releasing the dispenser button.

Water may continue to dispense

after the button is released.

If no water is dispensed when the refrigerator is first

installed, there may be air in the water line system.

Press the dispenser button for at least 2 minutes to

remove trapped air from the water line and to fill the

water system. During this process, the dispenser

noise may be loud as the air is purged from the

water line system. To flush out impurities in the

water line, throw away the first 6 glassfuls of water.

NOTE: To avoid water deposits, the dispenser

should be cleaned periodically by wiping with a

clean cloth or sponge.

Water Filter Accessory

The water filter is an option at extra cost

and is available from your dealer. Specify

WR97X0214. It has complete installation

instructions and installs on 1/4″ O.D.

copper water line or plastic tubing that

is included in a GE SmartConnect

™

Refrigerator Tubing kit. When using the

plastic tubing, an additional piece of plastic

tubing (WX08X10002) must also be

ordered since the plastic tubing should

not be cut.

NOTE: The only GE approved plastic tubing is that

supplied in GE SmartConnect

™

Refrigerator Tubing

kits. Do not use any other plastic water supply line

because the line is under pressure at all times.

Certain types of plastic will crack or rupture with

age and cause water damage to your home.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Feeler Arm in

the STOP

(up) position

Feeler Arm in

the ON (down)

position

Feeler arm model

Power switch model

There are 2 types of icemakers:

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Care and cleaning of the refrigerator.

Cleaning the Outside

The door handles and trim.

Clean with

a cloth dampened with soapy water.

Dry with a soft cloth.

Keep the outside clean.

Wipe with a clean

cloth lightly dampened with kitchen

appliance wax or mild liquid dish

detergent. Dry and polish with a clean,

soft cloth.

The stainless steel door panels and handles.

The stainless steel panels can be cleaned

with a commercially available stainless steel

cleaner or a similar product using a clean,

soft cloth. Do not use appliance wax, polish,

bleach or products containing chlorine on

stainless steel doors and handles.

For best results, GE recommends using

stainless steel cleaner PM10X311 with

the WX10X307 polishing cloth, or for

convenience the SS cleaning wipes, part

number WX10X10001.

Do not wipe the refrigerator with a soiled dish cloth

or wet towel. These may leave a residue that

can erode the paint. Do not use scouring pads,

powdered cleaners, bleach or cleaners containing

bleach because these products can scratch and

weaken the paint finish.

Cleaning the Inside

To help prevent odors,

leave an open box of

baking soda in the fresh food and freezer

compartments.

Unplug the refrigerator before cleaning.

If this

is not practical, wring excess moisture out

of sponge or cloth when cleaning around

switches, lights or controls.

Use warm water and baking soda solution—

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) of water. This both cleans

and neutralizes odors. Thoroughly rinse

and wipe dry.

Avoid cleaning cold glass shelves (on some models)

with hot water because the extreme temperature

difference may cause them to break. Handle glass

shelves carefully. Bumping tempered glass can cause

it to shatter.

Do not wash any plastic refrigerator parts in the

dishwasher.

Do not clean with any products containing detergent,

bleach or ammonia. They may damage the

refrigerator.

Condenser

There is no need for routine condenser

cleanings in normal home operating

environments. However, in environments

that may be particularly dusty or greasy, the

condenser should be cleaned periodically

for efficient refrigerator operation.

For models with a base grille,

the grille must

be removed in order to clean the condenser.

To remove the base grille:

Grasp it about 6″ from each end and pull

its bottom edge toward you.

To replace the base grille:

Insert the tops of the metal clips into the

oval vents, making sure one of the plastic

tabs on the back of the grille goes into each

of the oval vents. Then push the bottom of

the grille forward until it snaps into place.

Cleaning the condenser:

Sweep away or vacuum up dust.

For models with a base grille,

reach the

condenser by inserting a brush or vacuum

hose into the oval holes.

For models without a base grille,

reach the

condenser by inserting a brush or vacuum

hose under the bottom of the refrigerator.

For best results, use a brush specially

designed for this purpose. It is available

at most appliance parts stores.

Moving the Refrigerator

Be careful when moving the refrigerator

away from the wall. All types of floor

coverings can be damaged, particularly

cushioned coverings and those with

embossed surfaces.

BEFORE moving the refrigerator away from the wall,

be sure to adjust the leveling legs up. (See page 10

for details.)

Pull the refrigerator straight out and return

it to position by pushing it straight in.

Moving the refrigerator in a side direction

may result in damage to the floor covering

or refrigerator.

When pushing the refrigerator back, make sure you

don’t roll over the power cord or icemaker supply line

(on some models).

GEAppliances.com

Preparing for Vacation

For long vacations or absences, remove

food and unplug the refrigerator. Move

the refrigerator control to the

0 (off)

position

and clean the interior with a baking soda

solution of one tablespoon (15 ml) of

baking soda to one quart (1 liter) of water.

Leave the doors open.

Set the icemaker power switch to the

O (off)

position or move the feeler arm to the

STOP

(up) position (depending on model) and

shut off the water supply to the refrigerator.

If the temperature can drop below freezing,

have a qualified servicer drain the water

supply system (on some models) to prevent

serious property damage due to flooding.

Preparing to Move

Secure all loose items such as grille,

shelves and drawers by taping them

securely in place to prevent damage.

Be sure the refrigerator stays in an upright position

during moving.

Some models have only one light.

Freezer Compartment Dome Light (on some models)

CAUTION:Light bulbs may be hot.

Unplug the refrigerator.

The bulb is located behind a light

shield at the back of the freezer

compartment. To remove, squeeze

the top and bottom of the shield and

pull the shield off.

After replacing with an appliance bulb

of the same or lower wattage, replace

the shield.

Plug the refrigerator back in.

Replacing the light bulbs.

Setting either or both controls to 0 (off) does not remove power to the light circuit.

Refrigerator Compartment—Upper Light

CAUTION:Light bulbs may be hot.

Unplug the refrigerator.

The bulbs are located at the top of the

compartment near the opening.

Replace with an appliance bulb of

the same or lower wattage.

Plug the refrigerator back in.

Light shield

Consumer Support

Troubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

Rollers allow you to move the refrigerator away from the

wall for cleaning.

Leveling Legs near each front corner of the refrigerator,

next to the rollers, should be adjusted if any of the

following occurs:

• Refrigerator wobbles due to front roller not being firmly

positioned on the floor.

• Door(s) do not close easily when opened to 45°.

NOTE:

• BEFORE moving the refrigerator away from the wall,

be sure to turn the leveling legs counterclockwise so that

the weight of the refrigerator is fully transferred to the

front rollers.

• The refrigerator will not be level from front to back. It

will have a slight backward tilt for proper door-closing.

To adjust the leveling legs,

turn the two front leveling

legs clockwise to raise the

front of the refrigerator and

counterclockwise to lower it.

ROLLERS AND LEVELING LEGS

Clockwise to raise

refrigerator

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time – Refrigerator Installation

15 minutes

Reversing the Door Swing

1 hour

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is not

covered under the Warranty.

Allow the following clearances for ease of installation,

proper air circulation and plumbing and electrical

connections.

• Sides 1/8″ (3 mm)

• Top 1″ (25 mm)

• Back 1″ (25 mm)

If the refrigerator is to be installed next to a wall on the

hinge side, allow 5/16″ (8 mm) door clearance.

CLEARANCES

If the refrigerator has an icemaker, it will have to be

connected to a cold water line. A water supply kit

(containing copper tubing, shutoff valve, fittings and

instructions) is available at extra cost from your dealer,

by visiting our Website at GEAppliances.com (in

Canada at www.GEAppliances.ca) or from Parts and

Accessories, 1.800.661.1616.

WATER SUPPLY TO THE ICEMAKER

(on some models)

Installation Instructions

Model 18

If you have questions, call 1.800.GE.CARES

or visit our Website at:

GEAppliances.com

In Canada, call 1.800.561.3344

or Visit our Website at:

www.GEAppliances.ca

• Do not install the refrigerator where the temperature

will go below 60°F (16°C) because it will not run often

enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature

will go above 100°F (37°C) because it will not perform

properly.

• Install it on a floor strong enough to support it fully

loaded.

REFRIGERATOR LOCATION

INSTALLING THE WATER LINE (ON SOME MODELS)

Recommended copper water supply kits are WX8X2, WX8X3

or WX8X4, depending on the amount of tubing you need.

Approved plastic water supply lines are GE SmartConnect

™

Refrigerator Tubing (WX08X10006, WX08X10015 and

WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis

Water System, the only approved installation is with a GE RVKit.

For other reverse osmosis water systems, follow the

manufacturer’s recommendations.

This water line installation is not warranted by the refrigerator

or icemaker manufacturer. Follow these instructions carefully

to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing

can cause damage to refrigerator parts and lead to water leakage

or flooding. Call a qualified plumber to correct water hammer

before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the

water line to the hot water line.

If you use your refrigerator before connecting the water line,

make sure the feeler arm is in the

STOP

(up) position.

Do not install the icemaker tubing in areas where temperatures

fall below freezing.

When using any electrical device (such as a power drill) during

installation, be sure the device is double insulated or grounded

in a manner to prevent the hazard of electric shock, or is battery

powered.

All installations must be in accordance with local plumbing

code requirements.

BEFORE YOU BEGIN

Installation Instructions

WHAT YOU WILL NEED

• Copper or GE SmartConnect

™

Refrigerator Tubing kit,

1/4″ outer diameter to connect the refrigerator to the water

supply. If using copper, be sure both ends of the tubing are

cut square.

To determine how much tubing you need: Measure the distance

from the water valve on the back of the refrigerator to the water

supply pipe. Then add 8′ (2.4 m). Be sure there is sufficient extra

tubing (about 8′ [2.4 m] coiled into 3 turns of about 10″ [25 cm]

diameter) to allow the refrigerator to move out from the wall

after installation.

GE SmartConnect

™

Refrigerator Tubing Kits are available in the

following lengths:

6′ (1.8 m) – WX08X10006

15′ (4.6 m) – WX08X10015

25′ (7.6 m) – WX08X10025

Be sure that the kit you select allows at least 8′ (2.4 m) as

described above.

NOTE: The only GE approved plastic tubing is that supplied

in GE SmartConnect

™

Refrigerator Tubing kits. Do not use any

other plastic water supply line because the line is under pressure

at all times. Certain types of plastic will crack or rupture with age

and cause water damage to your home.

• A GE water supply kit (containing tubing, shutoff

valve and fittings listed below) is available at extra

cost from your dealer or from Parts and Accessories,

1.800.661.1616.

• A cold water supply. The water pressure must be

between 20 and 120 p.s.i. (1.4–8.1 bar).

• Power drill.

• 1/2″ or adjustable wrench.

• Straight and Phillips blade screwdriver.

• Two 1/4″ outer diameter compression nuts and

2 ferrules (sleeves)—to connect the copper tubing

to the shutoff valve and the refrigerator water valve.

• If you are using a GE SmartConnect

™

Refrigerator

Tubing kit, the necessary fittings are preassembled

to the tubing.

• If your existing copper water line has a flared fitting

at the end, you will need an adapter (available at

plumbing supply stores) to connect the water line to

the refrigerator OR you can cut off the flared fitting

with a tube cutter and then use a compression fitting.

Do not cut formed end from GE SmartConnect

™

Refrigerator tubing.

• Shutoff valve to connect to the cold water line.

The shutoff valve should have a water inlet with a

minimum inside diameter of 5/32″ at the point of

connection to the COLD WATER LINE. Saddle-type

shutoff valves are included in many water supply kits.

Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes.

WHAT YOU WILL NEED (CONT.)

Place the compression nut and ferrule (sleeve)

for copper tubing onto the end of the tubing and

connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve.

Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the shutoff valve and tighten

compression nut until it is hand-tight; then tighten

one additional turn with a wrench. Overtightening

may cause leaks.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

CONNECT THE TUBING

TO THE VALVE

Turn the main water supply

on counterclockwise and flush

out the tubing until the water

is clear.

Shut the water off at the

water valve after about one

quart (1 liter) of water has

been flushed through the tubing.

FLUSH OUT THE TUBING

INSTALLING THE WATER LINE (CONT.)

Saddle-Type

Shutoff Valve

Compression

Nut

SmartConnect

™

Tubing

Packing Nut

Outlet Valve

Ferrule (sleeve)

Fasten the shutoff valve to the cold water pipe with

the pipe clamp.

Tighten the clamp screws until the sealing washer

begins to swell.

NOTE: Do not overtighten or you may crush the

tubing.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

FASTEN THE SHUTOFF VALVE

Route the tubing between the cold water line and

the refrigerator.

Route the tubing through a hole drilled in the wall

or floor (behind the refrigerator or adjacent base

cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing to

allow the refrigerator to move out from the wall

after installation

ROUTE THE TUBING

Washer

Inlet End

Clamp Screw

Vertical Cold

Water Pipe

Saddle-Type

Shutoff Valve

Pipe Clamp

Installation Instructions

SHUT OFF THE MAIN WATER SUPPLY

AND UNPLUG REFRIGERATOR

Turn on the nearest faucet counterclockwise long

enough to clear the line of water.

Install the shutoff valve on the nearest frequently used

drinking water line.

Choose a location for the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When it is necessary to connect

into a horizontal water pipe, make the connection

to the top or side, rather than at the bottom, to

avoid drawing off any sediment from the water pipe.

Drill a 1/4″ hole in the water pipe (even if using a

self-piercing valve), using a sharp bit. Remove any

burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4″ hole may result in reduced

ice production or smaller cubes.

DRILL THE HOLE FOR THE VALVE

Installation Instructions

NOTES:

• Before making the connection to the refrigerator,

be sure the refrigerator power cord is not

plugged into the wall outlet.

• We recommend installing a water filter if your

water supply has sand or particles that could clog

the screen of the refrigerator’s water valve. Install

it in the water line near the refrigerator. If using

GE SmartConnect

™

Refrigerator Tubing kit, you

will need an additional tube (WX08X10002) to

connect the filter. Do not cut plastic tube to

install filter.

Remove the screws holding the right side of the

access cover. Fold back the cover.

Remove the plastic flexible cap

from the water valve

(refrigerator connection).

Place the compression nut and

ferrule (sleeve) onto the end of

the tubing as shown. On GE

SmartConnect

™

Refrigerator

Tubing kit, the nuts are already

assembled to the tubing.

Insert the end of the tubing into the water valve

connection as far as possible. While holding the

tubing, tighten the fitting.

For plastic tubing from a GE SmartConnect

™

Refrigerator Tubing kit, insert the molded end

of the tubing into the water valve connection and

tighten compression nut until it is hand-tight;

then tighten one additional turn with a wrench.

Overtightening may cause leaks.

Fasten the tubing into the clamp provided to hold

it in a vertical position. You may need to pry open

the clamp.

CONNECT THE TUBING TO THE

REFRIGERATOR

Tighten any connections that leak.

TURN THE WATER ON AT THE

SHUTOFF VALVE

Reattach the access cover.

1/4″ Compression Nut

Tubing Clamp

1/4″ Tubing

Ferrule (sleeve)

Refrigerator

Connection

SmartConnect

™

Tubing

One of the illustrations below will look like the

connection on your refrigerator.

Icemaker Models without Water Dispenser

CONNECT THE TUBING TO THE

REFRIGERATOR (CONT.)

1/4″ Tubing

Tubing Clamp

1/4″ Compression Nut

Ferrule (sleeve)

SmartConnect

™

Tubing

Refrigerator Connection

Water Dispenser Models

When reversing the door swing:

• Read the instructions all the way through before

starting.

• Handle parts carefully to avoid scratching paint.

• Set screws down by their related parts to avoid using

them in the wrong places.

• Provide a non-scratching work surface for

the doors.

IMPORTANT: Once you begin, do not move the

cabinet until door-swing reversal is completed.

These instructions are for changing the hinges from

the right side to the left side—if you ever want to change

the hinges back to the right side, follow these same

instructions and reverse all references to left and right.

Unplug the refrigerator from its electrical outlet.

Empty all door shelves, including the dairy

compartment.

IMPORTANT NOTES

3/8″ Head socket driver

(a 6-point socket is

recommended)

TOOLS YOU WILL NEED

Phillips screwdriver

Putty knife or

thin-blade screwdriver

Masking tape

T20 or T25 Torx

driver, whichever your

model requires

On power switch models, set the icemaker power

switch to the

l (on)

position. On feeler arm models,

move the feeler arm to the

(down) position.

The icemaker will not begin to operate until it

reaches its operating temperature of 15°F (–9°C) or

below. It will then begin operation automatically.

NOTE: In lower water pressure conditions, the

water valve may turn on up to 3 times to deliver

enough water to the icemaker.

Installation Instructions

Arrange the coil of tubing so that it does not vibrate

against the back of the refrigerator or against the

wall. Push the refrigerator back to the wall.

PLUG IN THE REFRIGERATOR

START THE ICEMAKER

Feeler Arm in the

STOP (up) position

Feeler Arm in

the ON (down) position

REVERSING THE DOOR SWING

INSTALLING THE WATER LINE (CONT.)

Installation Instructions

TRANSFER BOTTOM HINGE

BRACKET TO THE LEFT

For models with a base grille, remove it by grasping it

about 6″ from each end and pulling its bottom edge

toward you.

Using a Torx

driver, move the bottom hinge bracket

and plastic washer from the right side to the left side.

NOTE: If the washer is not on the hinge bracket,

check to see if it is stuck to the bottom of the door.

Plastic Washer

Hinge Bracket

For models with a base grille, before replacing the

base grille, remove the grille cap by removing the

screw. Screw the cap to the opposite side.

Replace the base grille by inserting the tops of the

metal clips into the oval vents, making sure one of the

plastic tabs on the back of the grille goes into each of

the oven vents. Then push the bottom of the grille

forward until it snaps into place.

REMOVE REFRIGERATOR DOOR

Tape the door shut with masking tape.

Remove the center hinge pin with a 3/8″ socket

and ratchet.

Remove the tape and tilt the door away from the

cabinet. Remove and save the washer on the hinge pin.

Lift the door straight up to free its bottom socket from

the pin in the bottom hinge bracket.

Set the door on a non-scratching surface with the

inside up.

CAUTION: Do not let door drop to the floor.

To do so could damage the door stop.

TRANSFER TOP HINGE TO

THE LEFT

Interchange hinge and screws at top right with screws

at the top left of cabinet.

Do not tighten screws on hinge side at this time.

Plastic Washer

Fresh Food Door

Hinge Pin

Center Hinge

Bracket

REMOVE FREEZER DOOR

Tape the door shut with masking tape.

Remove the hinge cover on top of the freezer door

(on some models).

Remove the two Torx

screws, then lift the hinge

straight up to free the hinge pin from the socket in

the top of the door.

Remove the tape and tilt the door away from the

cabinet. Lift it off the center hinge pin.

Set the door on a non-scratching surface with

the inside up.

Top Hinge

TRANSFER CENTER HINGE

BRACKET TO THE LEFT

Remove the center hinge bracket by removing the

three Torx

screws.

NOTE: Keep these screws with the hinge bracket.

They are long screws and will be used when installing

the hinge on the other side.

On some models, you will need to remove the color-

matched caps from the screw heads before you can

remove the screws. Use the edge of a thin flat blade to

gently pry the caps off the screw heads. (A putty knife

works well for this.) Cover the blade with tape to

prevent scratching the paint.

Remove the three Torx

screws from the center left

side of the cabinet. Screw them into the holes on

the right side.

Place the center hinge bracket over the holes at

the center left side of the cabinet. Insert and

tighten the three long screws.

Replace the caps by snapping them over the screws

with your finger.

TRANSFER DOOR STOPS

On each door, move the metal door stop from the

right to the left.

Move any screws from the left to the right.

Door Stop

Left Side

Right Side

Screw Cap

Installation Instructions

REVERSING THE DOOR SWING (CONT.)

TRANSFER REFRIGERATOR

DOOR HANDLE TO THE RIGHT

Plastic handle:

Remove the plug

button by carefully

prying under the edge

with a putty knife.

Remove the

exposed screw holding

the handle. Remove

the two screws holding

the handle to the top

of the door.

Stainless steel handle (on some models):

Remove the two

screws holding the

handle to the top of

the door. Loosen the

set screw with the

3/32″ Allen wrench

(supplied) and remove

the handle. Remove

the handle fastener

with the 3/16″ Allen

wrench (supplied).

Transfer the fastener

to the right side and

move the plug button

to the left side of the

refrigerator door.

After removing the

handle: Move the small

plug buttons from the top

right side of the door top

and insert them into the

holes on the opposite side.

Small Plug

Buttons

Move the large plug

button from the left

edge of the door and

insert it into the hole

on the opposite side.

Handle

Plug

Handle

Plug

Fastener

Plug

Button

Plug Button

Installation Instructions

TRANSFER FREEZER DOOR

HANDLE TO THE RIGHT

Plastic handle:

Remove the screws

holding the handle to

the top and bottom of

the door. Remove

handle. Move the

plug button on the

right side of the door to

the handle screw hole

on the left side.

TRANSFER REFRIGERATOR DOOR

HANDLE TO THE RIGHT (CONT.)

Transfer the door plug

button to the opposite

side.

Reinstalling the handle:

Attach the handle to the

right side of the door.

Plastic handle:

Line up the handle with the

screw holes in the top of the door

and tighten the screws. Install the

screw into the bottom of the handle.

Reinstall the handle plug.

Handle

Plug

Button

Stainless steel handle

(on some models):

Attach the handle

to the fastener and

tighten with the 3/32″

Allen wrench

(supplied). Line

up the handle with the

screw holes in the top

of the door and

tighten the screws.

Stainless steel handle

(on some models):

Remove the two

screws holding the

handle to the bottom

of the door. Loosen the

set screw with the

3/32″ Allen wrench

(supplied) and remove

the handle.

Remove the handle

fastener with the 3/16″

Allen wrench

(supplied). Transfer

the fastener to the right side and move the GE badge

to the left side of the freezer door. Remove the paper

covering on the adhesive backing prior to attaching

the badge to the door.

Reattach the handle on the opposite side using the

holes closest to the edge of the door.

Plastic handle:

Line up the handle

with the screw hole in

the top of the door and

tighten screw. Install

the two screws into the

bottom of the handle.

Move the plug

button on the right

side of the door to the

handle screw hole on

the left side.

Fastener

Plug

Button

Plug

Button

RE-HANG THE REFRIGERATOR

DOOR

Lower the refrigerator door onto the bottom

hinge pin.

Straighten the door and line it up with the center

hinge bracket.

Reinstall the center hinge pin with a 3/8″ socket.

Turn it until it extends through the hinge bracket

and into the door.

Plastic

Washer

Plastic Washer

Refrigerator Door

Hinge Pin

Center Hinge

Bracket

RE-HANG THE FREEZER DOOR

Lower the freezer door onto the center hinge pin.

Be sure the washer is in place.

Lift the top hinge so the pin fits into the door socket.

Support the door on the handle side and make sure

the door is straight and the gap between the doors is

even across the front. While holding the door in

place, tighten the top hinge screws.

Center Hinge Pin

Plastic Washer

Installation Instructions

REVERSING THE DOOR SWING (CONT.)

TRANSFER FREEZER DOOR

HANDLE TO THE RIGHT (CONT.)

Stainless steel handle

(on some models):

Attach the handle to

the fastener and tighten

with the 3/32″ Allen

wrench (supplied).

Line up the handle

with the screw holes in

the bottom of the door

and tighten the screws.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions

Installation Instructions

HUMMM...

WHOOSH...

■

The new high efficiency compressor may run faster and longer

than your old refrigerator and you may hear a high-pitched

hum or pulsating sound while it is operating.

■

You may hear a whooshing sound when the doors close.

This is due to pressure equalizing within the refrigerator.

Normal operating sounds. GEAppliances.com

Newer refrigerators sound different from older refrigerators. Modern refrigerators

have more features and use newer technology.

■

You may hear the fans spinning at high speeds. This happens

when the refrigerator is first plugged in, when the doors are

opened frequently or when a large amount of food is added to

the refrigerator or freezer compartments. The fans are helping

to maintain the correct temperatures.

CLICKS, POPS,

CRACKS and CHIRPS

■

You may hear cracking or popping sounds when the

refrigerator is first plugged in. This happens as the refrigerator

cools to the correct temperature.

■

The compressor may cause a clicking or chirping sound when

attempting to restart (this could take up to 5 minutes).

■

Expansion and contraction of cooling coils during and after

defrost can cause a cracking or popping sound.

■

On models with an icemaker, after an icemaking cycle, you

may hear the ice cubes dropping into the ice bucket.

■

On models with a dispenser, during water dispense, you may

hear the water lines move at initial dispense and after

dispenser button is released.

WATER SOUNDS

■

The flow of refrigerant through the freezer cooling coils may

make a gurgling noise like boiling water.

■

Water dropping on the defrost heater can cause a sizzling,

popping or buzzing sound during the defrost cycle.

■

A water dripping noise may occur during the defrost cycle as

ice melts from the evaporator and flows into the drain pan.

■

Closing the door may cause a gurgling sound due to pressure

equalization.

Do you hear what I hear? These sounds are normal.

For additional information on normal

icemaker operating sounds, see the

About the automatic icemaker section.

Before you call for service…

Troubleshooting Tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

Problem Possible Causes What To Do

Freezer door pops open

This is normal if, after • This indicates that there is a good seal on the freezer

when refrigerator door

popping open, the freezer door. If the freezer door does not automatically close after

is closed

door closed on its own. popping open, the rollers need adjusting. See

Rollers and

Leveling Legs.

Door does not close

Leveling legs need adjusting. • See

Rollers and Leveling Legs.

by itself

Refrigerator does

Refrigerator in defrost cycle. • Wait about 40 minutes for defrost cycle to end.

not operate

Refrigerator control in • Move the refrigerator and freezer control to a

0 (off)

position. temperature setting.

Refrigerator is unplugged. • Push the plug completely into the outlet.

The fuse is blown/circuit • Replace fuse or reset the breaker.

breaker is tripped.

Vibration or rattling

Refrigerator is not resting • Adjust leveling legs (See

Rollers and Leveling Legs).

(slight vibration

on all four rollers.

is normal)

Consumer Support

Troubleshooting Tips

Operating Instructions Safety InstructionsInstallation Instructions

Before you call for service…

Problem Possible Causes What To Do

Motor operates for

Normal when refrigerator • Wait 24 hours for the refrigerator to completely

long periods or cycles

is first plugged in. cool down.

on and off frequently

Often occurs when large • This is normal.

(Modern refrigerators

amounts of food are

with more storage

placed in refrigerator.

space and a larger

Door left open. • Check to see if package is holding door open.

freezer require more

Hot weather or frequent • This is normal.

operating time. They

door openings.

start and stop often

Temperature controls set • See

About the controls.

to maintain even

at the coldest setting.

temperatures.)

Refrigerator or freezer

Temperature control not set • See

About the controls.

compartment too warm

cold enough.

Warm weather or frequent • Set the temperature control one step colder.

door openings. See

About the controls.

Door left open. • Check to see if package is holding door open.

Freezer door popped open. • See the problem

Freezer door pops open when

refrigerator door is closed.

Frost or ice crystals

Door left open. • Check to see if package is holding door open.

on frozen food

Too frequent or too long

(frost within package

door openings.

is normal)

Food blocking freezer air vents. • Move items away from the back wall of the freezer.

Frequent “buzzing”

Icemaker power switch is in • On power switch models, set the power switch to the

O (off)

sound

the

I (on)

position, but the position. On feeler arm models, move the feeler arm to the

water supply to the refrigerator

STOP

(up) position. Keeping the power switch in the

I (on)

has not been connected. position or the feeler arm in the

(down) position will

damage the water valve.

Small or hollow cubes

Water filter clogged. • Replace filter cartridge with new cartridge or with plug.

Automatic icemaker

Icemaker power switch is not on. • On power switch models, set the power switch to the

does not work I (on)

position. On feeler arm models, move the feeler

(on some models)

arm to the

(down) position.

Water supply turned off or • See

Installing the water line.

not connected.

Freezer compartment too warm. • Wait 24 hours for the refrigerator to completely cool down.

Piled up cubes in the storage • Level cubes by hand.

bin cause the icemaker to shut off.

Ice cubes stuck in icemaker. • Turn off the icemaker, remove cubes and turn the

(Green power light on icemaker back on.

icemaker blinking.)

Ice cubes have

Ice storage bin needs cleaning. • Empty and wash bin. Discard old cubes.

odor/taste

Food transmitting odor/taste • Wrap foods well.

to ice cubes.

Interior of refrigerator • See

Care and cleaning.

needs cleaning.

Slow ice cube freezing

Door left open. • Check to see if package is holding door open.

Temperature control not set •See

About the controls.

cold enough.

• A newly installed refrigerator may take 12–24 hours

to begin making ice cubes.

Moisture forms on

Not unusual during • Wipe surface dry; then adjust the fresh food control

cabinet surface

periods of high humidity. setting one number higher and check again in 24 hours.

between the doors

Refrigerator has odor

Foods transmitting • Foods with strong odors should be tightly wrapped.

odor to refrigerator.

• Keep an open box of baking soda in the refrigerator;

replace every three months.

Interior needs cleaning. • See

Care and cleaning.

Refrigerator compartment

No power at outlet. • Replace fuse or reset the breaker.

light does not work

Light bulb burned out or loose. • See

Replacing the light bulbs.

La page charge ...

GE Profile GTS18DCPLBB Le manuel du propriétaire

Marque: GE Profile

Modèle: GTS18DCPLBB

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: GE Profile GTS18DCPLBB Owner's manual
español: GE Profile GTS18DCPLBB El manual del propietario

GE Profile GTS18DCPLBB Le manuel du propriétaire

GE Profile GTS18DCPLBB Le manuel du propriétaire

dans d''autres langues

Autres documents