Sub Zero IW-30A-RH Guide d'installation

Marque: Sub Zero

Modèle: IW-30A-RH

Taper: Guide d'installation

Ce manuel convient également à

Wine Storage Installation Guide

WINE STORAGE

Contents

3 Wine Storage

4 Opening Dimensions

5 Electrical

6 Plumbing

6 Preparation

6 Anti-Tip Bracket

8 Placement

8 Alignment

9 Water Line

10 Custom Panels

12 Panel Installation

14 Completion

Features and specications are subject to change at any

time without notice. Visit subzero.com/specs for the most

up-to-date information.

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

IMPORTANT NOTE: Save these instructions for the local

electrical inspector.

Sub-Zero Customer Care 800.222.7820

subzero.com

Product Information

Important product information including the model and

serial number are listed on the product rating plate. The

rating plate is located on the handle side wall, directly below

the control panel. Refer to the illustration below.

If service is necessary, contact Sub-Zero factory certied

service with the model and serial number. For the name

of the nearest Sub-Zero factory certied service or for

questions regarding the installation, visit the contact & sup-

port section of our website, subzero.com or call Sub-Zero

customer care at 800-222-7820.

WINE STORAGE

Tools | Materials

• Screwdrivers—standard, Phillips and Torx.

• Power drill.

• Drill bits (masonry bits required for concrete installation).

• Standard socket and wrench set.

• 2' and 4' levels.

• Tubing cutter.

• 3'

(.9 m) of

/4" OD copper, braided stainless steel or

PEX tubing.

• Saddle valve.

• Material to protect home, ooring and cabinetry during

installation.

Rating plate location.

RATING PLATE

Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

Opening Dimensions

WINE STORAGE

OPENING DIMENSIONS

W H

18" Model 18" (457) 84" (2134)

24" Model 24" (610) 84" (2134)

30" Model 30" (762) 84" (2134)

The depth of each wine storage model is 24" (610). Allow for

panel thickness when planning the nished opening depth.

A minimum 3

/2" (89) nished return is required on all sides

of the opening. Framed cabinets will require additional

nished ller material behind the face frame for a proper

installation. Refer to the illustration.

DUAL INSTALLATION

When installing two units side by side in a dual installa-

tion, the opening width is the width of the two units added

together. A dual installation kit will be required for this instal-

lation. If a dual installation kit is not specied, a minimum

(51) ller strip is required between units.

Dual installation kits are available through an authorized

Sub-Zero dealer. For local dealer information, visit the nd a

showroom section of our website, subzero.com. For ques-

tions regarding the installation, call Sub-Zero customer care

at 800-222-7820.

25"

(635)

OPENING

DEPTH

OPENING WIDTH

OPENING

HEIGHT

NOTE:

/2" (89) finished returns will be visible and should be finished to match cabinetry.

SIDE

VIEW

TOP VIEW

FRONT VIEW

/2" (89)

FINISHED

RETURN

FRAMELESS CABINETRY

/4"

(19)

TYPICAL

/2" (89)

FINISHED

RETURN

FILLER

FRAMED CABINETRY

W W

subzero.com

SITE PREPARATION

HOME SECURITY CONNECTION

If the unit will be connected to a home security system, low-

voltage leads must be provided to the unit. Two connectors

are located behind the top trim. Provide 10'

(3 m) minimum

lead wires for each connector, exiting the back wall near the

electrical receptacle.

Remove the top trim by disengaging the trim from the hinge

side of the unit. Rotate the trim and remove the trim pin from

the handle side vertical support. Refer to the illustrations

below. Use spade terminals or wire nuts to make proper

wiring connections. Refer to the following color codes:

• Normally open contacts—white with red stripe wire.

• Common—gray with white stripe wire.

CAUTION

The alarm circuit in the unit is intended as a low-

voltage, low-current device only. It should not be used

to switch line power. Any unused terminals should be

completely insulated and all wires should be secured

away from conductive or moving components.

Electrical

Installation must comply with all applicable electrical codes.

The electrical supply must be located within the shaded

area shown in the illustration and chart below. A separate

circuit, servicing only this appliance is required. A ground

fault circuit interrupter (GFCI) is not recommended and may

cause interruption of operation.

The electrical outlet must be positioned with the grounding

prong to the right of the thinner blades.

CAUTION

The outlet must be checked by a qualied electrician to

be sure that it is wired with the correct polarity. Verify

that the outlet is properly grounded.

WARNING

Do not use an extension cord, two-prong adapter or

remove the power cord ground prong.

ELECTRICAL REQUIREMENTS

Electrical Supply 115 VAC, 60 Hz

Service 15 amp

Receptacle 3-prong grounding-type

ELECTRICAL SUPPLY LOCATION

18" Model 6" (152)

24" Model 9

/2" (241)

30" Model 12

/2" (318)

/4" (6)

/4"

(108)

/2"

(114)

FLOOR

LEFT SIDE

OF OPENING

Electrical supply location.

Top trim—hinge side.

Top trim—handle side.

Sub-Zero Customer Care 800.222.7820

SITE PREPARATION

SCREW

Kickplate removal.

Preparation

Uncrate the unit and inspect for damage. Remove the wood

base and discard shipping bolts and brackets. Remove and

recycle packing materials. Do not discard the kickplate, anti-

tip bracket and hardware.

Remove the kickplate by extracting the two mounting

screws. Refer to the illustration below.

Anti-Tip Bracket

WARNING

To prevent the unit from tipping forward, the anti-tip

bracket must be installed.

The back of the anti-tip bracket must be installed 24" (610)

from the front of the unit (without panels). Use all anti-tip

bracket hardware as instructed for wood or concrete oors.

IMPORTANT NOTE: For wood or concrete oor applications,

if the #12 screws do not hit a wall stud or wall plate, use the

#8 screws and #12 washers with the wall anchors.

IMPORTANT NOTE: In some installations the subooring or

nished oor may necessitate angling the screws used to

fasten the anti-tip bracket to the back wall.

Plumbing

Installation must comply with all applicable plumbing

codes.

For model IW-30CI, the water supply line should be located

within the shaded area shown in the illustration below.

The water supply line should be connected to the house

supply with an easily accessible shut-off valve. Do not use

self-piercing valves. The water supply line must be ush

to the oor and not interfere with installation of the anti-tip

bracket.

A reverse osmosis system can be used provided there is

constant water pressure of 35–120 psi

(2.4–8.3 bar) supplied

to the unit at all times. In this application, the water ltra-

tion system must be bypassed. Refer to water lter bypass

on page 15. A copper line is not recommended for this

application.

PLUMBING REQUIREMENTS

Water Supply Line

/4" OD copper, braided

stainless steel or PEX tubing

Water Pressure 35–120 psi

(2.4–8.3 bar)

Excess Water Line for Connection 36" (914)

WATER SUPPLY LOCATION

IW-30CI 6" (152)

3" (76)

6" (152)

RIGHT SIDE

OF OPENING

AREA EXTENDS

/2" (13)

FORWARD ON FLOOR

Water supply location

(IW-30CI).

subzero.com

SITE PREPARATION

CONCRETE WEDGE ANCHOR INSTALLATION

1 Drill a

/8" (10) diameter hole any depth exceeding the

minimum embedment. Clean the hole or drill additional

depth to accommodate drill nes.

2 Assemble the washer and nut ush with the end of

anchor to protect threads. Drive the anchor through the

material to be fastened until the washer is ush with the

surface material.

3 Expand the anchor by tightening the nut 3–5 turns past

hand-tight position or to 25 foot-pounds of torque.

WARNING

Verify there are no electrical wires or plumbing in the

area which the screws could penetrate.

CAUTION

Always wear safety glasses and use other neces-

sary protective devices or apparel when installing or

working with anchors.

Anchors are not recommended for use in lightweight

masonry material such as block or brick, or for use in

new concrete which has not had sufcient time to cure.

The use of core drills is not recommended to drill holes

for the anchors.

Anti-Tip Bracket

WOOD FLOOR APPLICATION

After properly locating the anti-tip bracket in the opening,

drill pilot holes

/16" (5) diameter maximum in the wall studs

or wall plate. Use the #12 screws and washers to secure the

brackets. Verify the screws penetrate through the ooring

material and into wall studs or wall plate a minimum of

/4"

(19)

. Refer to the illustration and chart below.

CONCRETE FLOOR APPLICATION

After properly locating the anti-tip bracket in the opening,

drill pilot holes

/16" (5) diameter maximum in the wall studs

or wall plate. Drill

/8" (10) diameter holes into the concrete

a minimum of 1

/2" (38) deep. Use the #12 screws and

washers to secure the brackets to the wall, and use the

/8"

wedge anchors to secure the brackets to the oor. Verify the

screws penetrate wall studs or wall plate a minimum of

/4"

(19)

. Refer to the illustration and chart below.

ANTI-TIP BRACKET PLACEMENT

18" Model 9" (229)

24" Model 12" (305)

30" Model 15" (381)

SUBFLOORING

WOOD FLOOR

WALL PLATE

FINISHED

FLOORING

SUBFLOORING

CONCRETE

FLOOR

WALL PLATE

FINISHED

FLOORING

/2"(38)

min

Wood oor.

Concrete oor.

Sub-Zero Customer Care 800.222.7820

INSTALLATION

Placement

CAUTION

Before moving the unit into position, secure the door |

drawers closed and protect any nished ooring.

Use an appliance dolly to move the unit near the opening.

The front leveling legs are extended below the front rollers to

improve stability during placement. Once the unit is placed

in front of the opening, completely retract the front leveling

legs to allow the unit to be rolled into position. Front and

rear leveling legs can be adjusted from the front once the

unit is positioned.

If the unit has been on its back or side, it must stand upright

for a minimum of 24 hours before connecting power.

Plug the power cord into the grounded outlet and roll the

unit into position. Verify the anti-tip bracket is properly

engaged.

Alignment

LEVELING

Once the unit is in position, height adjustment can be made

from the front. Using a Phillips drive, turn clockwise to raise

the unit or counterclockwise to lower. Use the lowest torque

setting when using a power drill. Do not turn the leveling

legs by hand. Refer to the illustration below.

When the unit is properly leveled, door | drawer adjustments

are less likely to be necessary.

IMPORTANT NOTE: Level the unit to the oor, not sur-

rounding cabinetry. This could affect the operation of the

unit, such as door closing.

WARNING

To reduce the possibility of the unit tipping forward,

the front leveling legs must be in contact with the oor.

REAR

ADJUSTMENT

FRONT

ADJUSTMENT

Leveling.

subzero.com

INSTALLATION

Alignment

DEPTH ADJUSTMENT

Adjust the depth of the unit to t ush with surrounding

cabinetry. Follow these steps for a precision t:

1 Place decorative panel on a protected work surface.

Place the panel thickness gauge next to the panel to

determine which notch corresponds with the panel thick-

ness. Refer to the illustration below. Once the proper

notch has been determined, mark that notch with a

marker.

2 With the door closed, position the top of the unit using

the panel thickness gauge. Refer to the illustration

below. Insert a #8 x

/2" stainless steel screw above the

hinge, then insert a #8 x

/2" pan head screw on the

handle side of the unit. For narrower units, the door may

need to be opened to access the handle side screw

location. Repeat the process to align the bottom.

ANCHORING

Once the top and bottom are aligned, verify the door |

drawers open properly, then install remaining screws in each

side trim.

PANEL THICKNESS

GAUGE

FRONT OF

UNIT

CABINETRY

FACE

FRAME

SCREW

SIDE TRIM

Panel thickness.

Unit depth.

Water Line

For model IW-30CI, approximately 3' (.9 m) of

/4" plastic

tubing is connected to the unit with a preassembled

/4"

compression connection under the unit. The water line t-

ting connection kit, provided with the unit, contains a

/4"

compression union tting for connection to the household

water line.

Purge the water line prior to nal connection to the unit. This

will remove any debris that may be present in the tubing

from installing the new water line. Connect the plastic tubing

from the unit to the house water supply line with the tting

connection kit provided. Locate the water line in the notch

as shown in the illustration below. Check all water line t-

tings for leaks.

IMPORTANT NOTE: If a reverse osmosis system used, it is

recommended that the water ltration system be bypassed

by removing the lter.

IMPORTANT NOTE: Water lines can not be exposed to

freezing temperatures.

WATER LINE

CONNECTION

NOTCH

Water line (IW-30CI).

Sub-Zero Customer Care 800.222.7820

Custom Panels

Custom door | drawer panels and handle hardware must

be installed. Stainless steel panels are available through an

authorized Sub-Zero dealer. For local dealer information,

visit the nd a showroom section of our website,

subzero.com.

The thickness of the custom panel can vary. A minimum

/8" (16) thick panel is required, but the thickness can be

increased provided it does not exceed the maximum panel

weight indicated in the chart below. The depth of each

model is 24"

(610). Allow for panel thickness when planning

the nished opening depth.

PANEL REQUIREMENTS

WEIGHT PER PANEL MAX

Door (column model) 35 lb (16 kg)

Door (tall model) 25 lb (11 kg)

Drawer 15 lb (7 kg)

PANEL THICKNESS MIN

All Panels

/8" (16)

Reveals between panels can vary,

/8" (3) reveals are typical.

CAUTION

When installing a panel thicker than 1" (25), the 90° stop

may be required to prevent damage to the unit and

adjacent cabinetry.

CAUTION

As reveals between cabinetry and the unit decrease,

severe nger pinching can occur while door is closing.

Finish all sides of custom panels. They will be visible when

the door is open.

D-style handles are recommended. Stainless steel tubular

and pro handles are avail able through an authorized

Sub-Zero dealer. For local dealer information, visit the nd

a showroom section of our website, subzero.com. Door

handles must be located near the edge of the panel oppo-

site the hinge and should be centered top to bottom. Drawer

handles must be located near the top edge of each panel.

PANEL INSTALLATION

subzero.com

PANEL INSTALLATION

Custom Panels

DOOR PANEL HEIGHT

The height of the custom door panel can extend beyond the

typical panel height, provided it does not exceed the weight

limit. Refer to the illustration below.

(45)

A DECORATIVE VALANCE

CANNOT EXTEND

BEYOND THIS PLANE

DOOR

PANEL

HINGE

24" (610)

TO BACK OF UNIT

84"

(2134)

/8" (3)

Upper valance (side view).

TOE KICK CLEARANCE

The height of the toe kick area can extend beyond the

typical toe kick height, provided it does not exceed the

dimensions in the illustration below. Toe kick heights from

(51) to 3

/8" (98) require a reduced toe kick accessory

available through an authorized Sub-Zero dealer. For local

dealer information, visit the nd a showroom section of our

website, subzero.com. For questions regarding the installa-

tion, call Sub-Zero customer care at 800-222-7820.

24" (610)

TO BACK OF UNIT

VENTED

LOUVERS

HINGE

DOOR

PANEL

/8" (29)

MAX

TOE KICK

ADJUSTMENT

A DECORATIVE TOE KICK

CANNOT EXTEND

BEYOND THIS PLANE

2" (51)*

6" (152)

FROM

FLOOR

*2" (51) to 3

/8" (98) requires sales accessory.

**Column models only.

Toe kick (side view).

Sub-Zero Customer Care 800.222.7820

PANEL INSTALLATION

Panel Installation

DOOR PANEL

Typical panel dimensions are based on an 84" (2134) nished

height with

/8" (3) reveals. Template placement must be

adjusted for panels exceeding typical dimensions.

For tall models, the door panel should be installed rst,

followed by the upper then lower drawer panel.

Place the panel face down on a protected work surface.

Position the template ush with the top and sides of the

panel. Verify the correct side of the template is being used,

then mark and drill holes. Refer to the illustration below.

For tall models, align the notch in the template with the

bottom of the door panel, then mark and drill holes. Refer to

the illustration below.

Use the T-20 torx drive provided to partially insert a #8 x

/2"

screw into the second hole from the top on each side of the

panel. The screws should be approximately

/16" (4) proud

of the panel and will support the weight of the panel during

installation.

Align the support screws on the back of the panel with the

slotted holes on both door mounting brackets. Opening the

door slightly may help with alignment. Once the panel is

supported by the screws, partially insert a #8 x

/2" screw

into the second hole from the bottom on each side of the

panel, but do not tighten.

CAUTION

As the reveal between cabinets and the unit decreases,

the potential exists for severe nger pinching if ngers

are placed in the opening when the door is closing.

BACK OF

DOOR PANEL

Door panel mounting.

BOTTOM OF

DOOR PANEL

EDGE OF DOOR PANEL

USE TABS FOR HINGE

SIDE PANEL EDGE ON

DUAL INSTALLATION

TOP OF

DOOR PANEL

84" APPLICATION

83 7/8" ACTUAL

EDGE OF DOOR PANEL

TOP OF DOOR PANEL

BOTTOM OF

DOOR PANEL

EDGE OF DOOR PANEL

USE TABS FOR HINGE

SIDE PANEL EDGE ON

DUAL INSTALLATION

TOP OF

DOOR PANEL

84" APPLICATION

83 7/8" ACTUAL

EDGE OF DOOR PANEL

BOTTOM OF

DOOR PANEL

Door panel template—top.

Door panel template—bottom

(tall model).

subzero.com

PANEL INSTALLATION

PANEL ADJUSTMENT

Close the door | drawers, now adjustments can be made to

align panels and reveals.

For side-to-side adjustment, move panels side to side, then

install and tighten all mounting screws.

For up-and-down and in-and-out adjustments, slightly

loosen the bracket screws. Depending on the level of

adjustment required, it may be helpful to loosen all of the

bracket screws which will allow for maximum adjustment.

Once the bracket screws are loosened, use the cam wrench

provided to rotate the cams to make adjustments. After

adjustments have been made, tighten all bracket screws.

Refer to the illustrations below.

BRACKET

SCREWS

IN-AND-OUT

CAM

BRACKET

SCREWS

UP-AND-DOWN

CAM

In-and-out adjustment.

Up-and-down adjustment.

Panel Installation

DRAWER PANELS—TALL MODEL

Place the panel face down on a protected work surface.

Position the template ush with the top and sides of the

panel. Verify the correct side of the template is being used,

then mark and drill holes. Refer to the illustration below.

Use the T-20 torx drive provided, to partially insert a #8 x

/2"

screw into the second hole from the top on each side of the

panel. The screws should be approximately

/16" (4) proud

of the panel and will support the weight of the panel during

installation.

Align the support screws on the back of the panel with the

slotted holes on both drawer mounting brackets. Refer to

the illustration below. Opening the drawer slightly may help

with alignment. Once the panel is supported by the screws,

partially insert a #8 x

/2" screw into the second hole from

the bottom on each side of the panel, but do not tighten.

RIGHT EDGE OF DRA

WER PANEL

TOP HOLES

FOR UPPER

AND LOWER

DRAWERS

BOTTOM

HOLES FOR

LOWER

DRAWER

BOTTOM

HOLES FOR

UPPER

DRAWER

7021340

TOP OF

DRAWER PANEL

LEFT EDGE OF DRAWER PANEL

TOP OF DRAWER PANEL

BACK OF

DRAWER PANEL

Drawer panel template—top.

Drawer panel mounting.

Sub-Zero Customer Care 800.222.7820

INSTALLATION

Completion

DOOR TRIM INSTALLATION

After panels have been adjusted, install the decorative side

trim to the door | drawers. To install, start at the top and

align the trim with the front and rear anges on the bracket,

then snap into place by pushing the trim toward the back

of the panel. Once the top is secure, continue the installa-

tion downward until the remaining trim is completely secure.

Refer to the illustrations below.

DOOR TRIM

FRONT

FLANGE

REAR

FLANGE

Door trim.

Bracket anges.

SIDE TRIM INSTALLATION

Install the decorative trim strip to the handle side of tall

and column models. The side trim snaps over the bracket

attached to the handle side of the unit. Refer to the illustra-

tion below.

Side trim.

TOP TRIM INSTALLATION

Identify the top trim strips by the notch on one end at the

bottom; this trim strip ts on the hinge side of the unit.

Insert the outer end of each trim strip behind the vertical

side trim. Engage the snap in the plastic side bracket and

slide the panel as far to the outside as possible. Refer to the

illustration below.

Rotate the inner end of each panel into the side ange of

the center shroud, next to the water lter access door. Press

on the trim strip to snap into place. Refer to the illustration

below.

Inner top trim.

Outer top trim.

subzero.com

INSTALLATION

WATER FILTER BYPASS

If the water ltration system will not be utilized, it can be

placed in water lter bypass mode by removing the water

lter. Follow these steps to remove the water lter:

1 Pull out on the bottom edge of the access door and tilt

upward.

2 To remove the lter, rotate counterclockwise one-quarter

turn, then pull out. Refer to the illustration below.

WARNING

Follow all city and state laws when storing, recycling or

discarding unused refrigerators and freezers.

Completion

KICKPLATE INSTALLATION

Position the kickplate and install using the two mounting

screws. Refer to the illustration below. Kickplate must

be removable for service. The oor cannot interfere with

removal.

A maximum 6"

(152) decorative kickplate can be attached

to the factory-installed kickplate. The two rows of vented

louvers can be covered if door panel is a minimum 4"

(102)

from nished oor.

To install a decorative kickplate, remove paper backing from

the magnets and attach decorative kickplate to magnets.

Magnets will allow the decorative kickplate to be removed,

if necessary.

Turn power on by touching ‘power’ on the control panel.

90° DOOR STOP

A 105° door stop is built into the hinges. To limit the door

to 90°, open the door slightly less than 90°, then use a

standard screwdriver blade to remove the existing clips from

each hinge. Locate the 90° clips from inside the plastic bag

containing product literature, then insert the 90° clips onto

each hinge. Refer to the illustration below.

SCREWMAGNET

CLIP

Kickplate installation.

90° door stop.

WATER FILTER

ACCESS DOOR

Water lter removal (IW-30CI).

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design, are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.

Atención al cliente de Sub-Zero 800.222.7820

ALMACENAMIENTO DE VINOS

Contenido

3 Almacenamiento de vinos

4 Dimensiones de abertura

5 Instalación eléctrica

6 Plomería

6 Preparación

6 Soporte antivuelco

8 Colocación en posición

8 Alineación

9 Línea de agua

10 Paneles personalizados

12 Instalación del panel

14 Finalización

Las características y especicaciones están sujetas a

cambios sin previo aviso. Visite subzero.com/specs para

obtener la información más actualizada.

Aviso importante

Para garantizar que este producto se instale y opere de

la forma más segura y eciente posible, tome nota de los

siguientes tipos de información resaltada en esta guía:

AVISO IMPORTANTE señala la información que es especial-

mente importante.

PRECAUCIÓN indica una situación en la que se pueden

sufrir heridas leves o provocar daños al producto si no se

siguen las instrucciones.

ADVERTENCIA indica peligro de que se produzcan heridas

graves o incluso la muerte si no se siguen las precauciones.

AVISO IMPORTANTE: En toda esta guía, las dimensiones

entre paréntesis son milímetros, a menos que se especi-

que lo contrario.

AVISO IMPORTANTE: Guarde estas instrucciones para el

inspector eléctrico local.

subzero.com

Información del producto

La información importante del producto, incluido el modelo

y número de serie de la unidad, se encuentra en la placa de

datos del producto. La placa de datos se encuentra en la

parte de abajo del panel de control, a la izquierda. Consulte

la siguiente ilustración.

Si necesita servicio, póngase en contacto con el centro

de servicio autorizado de Sub-Zero y tenga a la mano el

modelo y número de serie de la unidad. Para obtener los

datos del centro de servicio autorizado de Sub-Zero más

cercano o si tiene preguntas acerca de la instalación, visite

la sección de contacto y soporte técnico en nuestra página

de Internet subzero.com o llame a la línea de atención al

cliente de Sub-Zero al 800-222-7820.

ALMACENAMIENTO DE VINOS

Herramientas y materiales

• Destornilladores: estándar, Phillips y Torx.

• Taladro eléctrico.

• Brocas (se requieren brocas de mampostería para

instalación en concreto).

• Juego de llaves estándar y de vaso.

• Niveles 2' y 4'.

• Cortador de tubos.

• 3'

(0.9 m) de tubería de cobre, trenzada de acero

inoxidable o PEX de

/4" de diámetro exterior.

• Válvula de asiento.

• Material para proteger la casa, el piso y los gabinetes

durante la instalación.

Ubicación de la placa de datos.

PLACA DE DATOS

Atención al cliente de Sub-Zero 800.222.7820

PREPARACIÓN DEL SITIO

Dimensiones de abertura

ALMACENAMIENTO DE VINOS

DIMENSIONES DE ABERTURA

Ancho Altura

Modelo de 18" 18" (457) 84" (2134)

Modelo de 24" 24" (610) 84" (2134)

Modelo de 30" 30" (762) 84" (2134)

La profundidad de cada modelo de almacén de vinos es

24"

(610). Para determinar la profundidad de la abertura ya

con acabados, considere el grosor del panel. Se necesita

un tubo de retorno de 3

/2" (89) con acabados en todos los

lados de la abertura. Los gabinetes con marco necesitarán

material de relleno de acabado detrás del marco frontal para

lograr una instalación adecuada. Consulte la ilustración.

INSTALACIÓN DOBLE

Al colocar dos unidades juntas en una instalación doble, el

ancho de la abertura es la suma del ancho de ambas uni-

dades. Para esta instalación se requiere un kit de instalación

doble. Si el uso de un kit de instalación doble no está espe-

cicado, se debe utilizar una tira de relleno de 2"

(51) como

mínimo entre las unidades.

Los kits de instalación doble están disponibles a través de

un distribuidor autorizado de Sub-Zero. Para obtener más

información acerca de los distribuidores locales, visite la

sección para encontrar una sala de exhibición de nuestro

sitio web, subzero.com. Para preguntas sobre la instalación,

comuníquese con la línea de atención al cliente de Sub-Zero

al 800-222-7820.

PROFUNDIDAD DE

LA ABERTURA DE

25"

(635)

Ancho

ANCHO DE

LA ABERTURA

Altura

ALTURA DE

LA ABERTURA

NOTA: Los tubos de retorno de

/2" (89) con acabados quedarán a la vista y deben

estar listos para ajustarse a los gabinetes.

VIST

A LATERAL

VISTA SUPERIOR

VISTA FRONTAL

TUBO DE

RETORNO DE

(89) CON

ACABADOS

GABINETE SIN MARCO

TÍPICO DE

/4"(19)

TUBO DE

RETORNO DE

/2" (89) CON

ACABADOS

RELLENO

GABINETE CON MARCO

Ancho Ancho

subzero.com

PREPARACIÓN DEL SITIO

CONEXIÓN A LÍNEAS DE SEGURIDAD DEL HOGAR

Si la unidad se conecta a un sistema de seguridad de la

casa, se deben proporcionar cables de bajo voltaje para

la unidad. Hay dos conectores ubicados detrás del ribete

superior. Proporcione cables de 10'

(3 m) como mínimo para

cada conector, que salen de la pared posterior cerca del

tomacorriente eléctrico.

Retire el ribete superior al desengancharlo del lado de la

bisagra de la unidad. Gire el ribete y retire el pasador del

ribete del soporte vertical del lado de la manija. Consulte las

siguientes ilustraciones. Use las terminales tipo espada o

tuercas para cable para efectuar las conexiones de manera

correcta. Aplique los siguientes códigos de colores:

• Contactos normalmente abiertos — cable blanco con

línea roja.

• Común — cable gris con línea blanca.

PRECAUCIÓN

El circuito de la alarma de la unidad debe utilizarse

solamente como un dispositivo de bajo voltaje y baja

corriente. No debe usarse como interruptor de la línea

de energía. Cualquier terminal que no se utilice debe

estar completamente aislada y todos los cables deben

estar alejados de manera segura de componentes

conductores o móviles.

Instalación eléctrica

La instalación debe cumplir con todos los códigos eléc-

tricos vigentes. El suministro eléctrico debe colocarse

dentro del área sombreada que se muestra en la siguiente

ilustración. Es necesario un circuito independiente que dé

servicio únicamente a este aparato. No es recomendable

utilizar un circuito de fallos de conexión a tierra (GFCI, por

sus siglas en inglés) ya que puede interrumpir el funciona-

miento de la unidad. El tomacorriente eléctrico debe colo-

carse de tal forma que la clavija con conexión a tierra quede

a la derecha de las aspas más delgadas.

PRECAUCIÓN

Un electricista calicado debe revisar el tomacorriente

para asegurarse de que la conexión se haya realizado

con la polaridad correcta. Verique que el tomaco-

rriente esté debidamente conectado a tierra.

ADVERTENCIA

No utilice un cable de extensión, adaptador de dos cla-

vijas ni retire la clavija con conexión a tierra del cable

de alimentación.

REQUISITOS ELÉCTRICOS

Suministro eléctrico 115 V CA, 60 Hz

Servicio 15 amperes

Receptáculo Conexión a tierra de 3 clavijas

UBICACIÓN DEL SUMINISTRO ELÉCTRICO

Modelo de 18" 6" (152)

Modelo de 24" 9

/2" (241)

Modelo de 30" 12

/2" (318)

/4" (6)

/4"

(108)

/2"

(114)

SUELO

LADO IZQUIERDO

DE LA ABERTURA

Ubicación del suministro eléctrico.

CLAVIJA

Ribete superior—lado de la

bisagra.

Ribete superior—lado de la

manija.

Atención al cliente de Sub-Zero 800.222.7820

Preparación

Desembale la unidad e inspeccione si tiene algún daño.

Retire la base de madera y deseche los pernos y soportes

de transporte. Retire y recicle los materiales de embalaje.

No deseche el zócalo, el soporte antivuelco ni las piezas de

montaje.

Para quitar el zócalo extraiga los dos tornillos para montaje.

Consulte la siguiente ilustración.

Soporte antivuelco

ADVERTENCIA

Para evitar que la unidad se vuelque hacia el frente,

debe instalarse el soporte antivuelco.

La parte posterior del soporte antivuelco debe instalarse a

24"

(610) del frente de la unidad (sin paneles).

Utilice todas las piezas de montaje de los soportes anti-

vuelco de acuerdo con las instrucciones para suelos de

madera o de concreto.

AVISO IMPORTANTE: Para aplicaciones en suelo de madera

o de concreto, si los tornillos del #12 no alcanzan un trave-

saño o la placa de pared, utilice tornillos del #8 y arandelas

del #12 con los anclajes de pared.

AVISO IMPORTANTE: En algunas instalaciones el contrapiso

o el suelo terminado pueden necesitar inclinar los tornillos

utilizados para sujetar el soporte antivuelco a la pared del

fondo.

PREPARACIÓN DEL SITIO

TORNILLO

Extracción del zócalo.

Plomería

La instalación debe cumplir con todos los códigos de

plomería vigentes. Para el modelo IW-30CI, la tubería de

suministro de agua debe colocarse dentro del área som-

breada que se muestra en la siguiente ilustración. La línea

del suministro de agua debe conectarse al suministro

doméstico con una válvula de cierre de fácil acceso. Evite

utilizar válvulas autoperforantes. La línea de suministro de

agua no debe sobresalir del nivel de piso ni interferir en la

instalación del soporte antivuelco.

Se puede utilizar un sistema de ósmosis inversa siempre

y cuando la presión del agua que llegue a la unidad se

mantenga de forma constante entre 35 y 120 psi

(de 2.4 a 8.3

bares)

en todo momento. En esta aplicación, se debe desviar

el sistema de ltrado de agua. Consulte la desviación del

ltro de agua en la página 15. No es recomendable utilizar

una línea de cobre para esta aplicación.

REQUISITOS DE PLOMERÍA

Línea de suministro de agua Tubería de cobre, trenzada de

acero inoxidable o PEX de

/4" de

diámetro exterior.

Presión del agua De 35 a 120 psi

(de 2.4 a 8.3 bares)

Línea de exceso de agua para

la conexión

36" (914)

UBICACIÓN DEL SUMINISTRO DE AGUA

IW-30CI 6" (152)

3" (76)

VISTA FRONTAL

SUELO

VISTA SUPERIOR

PARED

POSTERIOR

/2"

(13)

(152)

LÍNEA

DE AGUA

(152)

LADO DERECHO

DE LA ABERTURA

LADO

DERECHO

DE LA

ABERTURA

3" (76)

VISTA FRONTAL

SUELO

VISTA SUPERIOR

PARED

POSTERIOR

/2"

(13)

(152)

LÍNEA

DE AGUA

(152)

LADO DERECHO

DE LA ABERTURA

LADO

DERECHO

DE LA

ABERTURA

Ubicación del suministro de

agua (parte posterior).

Ubicación del suministro de

agua (parte inferior).

La page est en cours de chargement...

Sub Zero IW-30A-RH Guide d'installation

Marque: Sub Zero

Modèle: IW-30A-RH

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Sub Zero IW-30A-RH Installation guide
español: Sub Zero IW-30A-RH Guía de instalación

Sub Zero IW-30A-RH Guide d'installation

Ce manuel convient également à

Sub Zero IW-30A-RH Guide d'installation

dans d''autres langues

Documents connexes

Autres documents