Installation Instructions
Instructions d’installation
Instrucciones de instalación
HMV1472BHS
Microwave Oven
Four à micro-ondes
Horno de microondas
Part # 0570001268 REV A
TABLE OF CONTENTS
MICROWAVE SAFETY ........................................................................... 2
INSTALLATION REQUIREMENTS ............................................................. 3
Tools and Parts ............................................................................. 3
Location Requirements ................................................................... 4
Electrical Requirements .................................................................. 5
INSTALLATION INSTRUCTIONS ............................................................. 6
Step 1 - Unpack Microwave Oven ....................................................... 6
Step 2 - Locate Wall Studs ............................................................... 7
Step 3 - Align Rear Wall Template and Mark Wall ..................................... 7
Step 4 - Drill Holes for Mounting Microwave Oven .................................. 9
Step 5 - Determine Ventilation Method ............................................. 10
Step 6 - Install Microwave Oven ....................................................... 11
Step 7 - Complete Installation ........................................................ 25
1
ENGLISH
MICROWAVE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and
on your appliance. Always read and obey all safety messages.
DANGER
WARNING
CAUTION
This is the safety alert symbol.
This symbol alerts you to potential hazards that can
kill or hurt you and others. All safety messages will
follow the safety alert symbol and either the word
“DANGER,” “WARNING” or “CAUTION.”
These words mean:
An imminently hazardous situation. You
could be killed or seriously injured if you
don’t immediately follow instructions.
A potentially hazardous situation
which, if not avoided, could result in
death or serious bodily injury.
A potentially hazardous situation
which, if not avoided, may result in
moderate or minor injury.
All safety messages will tell you what the potential hazard is, tell you
how to reduce the chance of injury, and tell you what can happen if the
instructions are not followed.
IMPORTANT SAFETY
INSTRUCTIONS
IMPORTANT: To reduce the risk of re, electrical shock, injury to
persons, or damage when using the microwave oven, follow basic
precautions, including the following:
•
Read all of the instructions before using this appliance.
•
This appliance must be properly installed and located in accordance
with the installation instructions before it is used.
•
The microwave oven must be properly grounded. Connect only to
properly grounded outlet. See “GROUNDING INSTRUCTIONS” found
in this installation guide.
•
Consult a qualied electrician or serviceman if the grounding
instructions are not completely understood, or if doubt exists as to
whether the microwave oven is properly grounded.
•
Do not remove ground prong.
•
Do not use an adapter.
•
Do not use an extension cord.
2
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
•
Disconnect electrical power at the fuse box or circuit breaker box
before installing.
•
The mounting surface must be capable of supporting the cabinet
load, in addition to the added weight of this 63–85 pound (28.5–
38.5 kg) product, plus additional oven loads of up to 50 pounds
(22.7 kg) or a total weight of 113–135 pounds (51.3–61.2 kg).
•
This product cannot be installed in cabinet arrangements such as an
island or a peninsula. It must be mounted to BOTH a top cabinet AND
a wall.
•
Use two or more people to move and install microwave oven.
READ AND SAVE THESE
INSTRUCTIONS
INSTALLATION REQUIREMENTS
TOOLS AND PARTS
Gather the required tools and parts before starting installation. Read and follow the
instructions provided with any tools listed here.
TOOLS NEEDED
•
Phillips Screwdriver
•
Pencil
•
Tape Measure or Ruler
•
Carpenter's Square
•
Tin Snips (for cutting damper, if
required)
•
Scissors
•
Cordless Electric Drill
•
³⁄₁₆", ½" and ⅝" Drill Bits
•
Reciprocating Saw, Hole Saw or
Keyhole Saw
•
Stud Finder
•
Hammer
•
Carpenter's Level
•
Duct Tape
•
Masking Tape
•
Safety Gloves and Goggles
PARTS SUPPLIED
Wood Screws (¹⁄₄" x 2")
Toggle Bolts and wing
nuts (³⁄₁₆" x 3")
Grease Filters (packed
separately)
3
ENGLISH
TOP CABINET TEMPLATE
REAR WALL TEMPLATE
Nylon Grommet (for metal
cabinets)
Top Cabinet Template Rear Wall Template
Glass Tray Turntable Ring
PARTS NEEDED
•
M6-1.00 Self-aligning Machine Screw (2) - of the length needed to go through
the cabinet bottom, ller block (if needed for recessed bottom cabinets), and
into the top of the microwave.
LOCATION REQUIREMENTS
24" (61.0 cm)
30"
(76.2 cm)
min.
16½" (42 cm)
c
b
d
a
2
" (5.1 cm)
A
Grounded 3 Prong Outlet
B
Bottom edge of cabinet
needs to be 30" (76.2 cm)
or more from the cooking
surface.
C
Backsplash
D
66" (167.6 cm) or more
from the oor to the top
of the microwave
•
The space between the cabinets on each side of the range must be at least 24"
(61 cm) wide and free of obstructions.
•
Grounded electrical outlet inside overhead cabinet. See “Electrical
Requirements” section.
•
If you are going to vent the microwave oven to the outside, see “Install
Microwave Oven” for exhaust and duct preparation.
•
When installing the microwave oven beneath smooth,
at cabinets, follow the
instructions on the Top Cabinet template for power cord clearance.
4
ENGLISH
ELECTRICAL REQUIREMENTS
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove the ground prong from the power cord plug.
Do not use an adapter.
Do not use an extension cord.
Failure to do so can result in death, fire or electrical shock.
Observe all governing codes and ordinances.
Product rating is 120 volts AC, 60 Hertz and 1500 watts. This product must be
connected to a supply circuit of the proper voltage and frequency.
The power supply cord and plug should be brought to a separate 15 to 20 ampere
branch circuit single grounded outlet.
The outlet box should be located in the cabinet above the microwave oven.
The outlet box and supply circuit should be installed by a
qualied electrician and
conform to the National Electrical Code or the prevailing local code.
GROUNDING INSTRUCTIONS
For a grounded, cord-connected microwave:
The microwave oven must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by providing an
escape wire for the electric current. The microwave oven is equipped
with a cord having a grounding wire with a grounding plug. The plug must
be plugged into an outlet that is properly installed and grounded.
WARNING: Improper use of the grounding plug can result in a risk of
electric shock. Consult a qualied electrician or serviceman if the
grounding instructions are not completely understood, or if doubt
exists as to whether the microwave oven is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have
a qualied electrician or serviceman install an outlet near the microwave
oven.
READ AND SAVE THESE
INSTRUCTIONS
5
ENGLISH
INSTALLATION INSTRUCTIONS
WARNING
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit breaker box
before installing microwave.
Failure to do so can result in death or electrical shock.
STEP 1 - UNPACK MICROWAVE OVEN
WARNING
Excessive Weight Hazard
Use two or more people to move and install microwave oven.
Failure to do so can result in back or other injury.
1. Using two or more people move the microwave close to the installation site.
2. Open the four aps on the carton top. From the top of the microwave, remove
the foam packing that contains the turntable and turntable ring.
NOTE: Do not remove the foam packing from the front of the oven.
3. Open the top of the plastic bag. Using two people, lift the microwave out of the
carton and gently set it front down on the foam packing. Remove the grease
lters and User Manual from the carton.
a
b
A
Foam Packing
B
Carton
4. Locate and remove the two screws attaching the mounting plate to the back of
the oven, and then remove the mounting plate.
6
ENGLISH
NOTE: The mounting plate will be used as the wall template and to mount
the microwave oven onto the wall.
a
b
A
Screws
B
Mounting Plate
(Wall Template)
5. Replace the two screws into the holes from which they were removed.
STEP 2 - LOCATE WALL STUDS
IMPORTANT: The microwave must be installed to at least one wall stud,
preferably two wall studs. If there is no wall stud within the cabinet opening, do
not install the microwave oven.
1. Find the studs using one of the following methods:
Stud nder – a magnetic device that locates nails.
OR
Using a hammer, tap lightly across the mounting surface while listening for a
solid sound. A solid sound indicates a stud location.
2. After locating the stud(s), nd the center by probing the wall with a small nail to
nd the edges of the stud. Then place a mark halfway between the edges. The
center of any adjacent studs should be 16" (40.6 cm) or 24" (61 cm) from this
mark.
3. Mark the center of the adjacent stud, and then draw a vertical plumb line down
the center of each stud.
STEP 3 - ALIGN REAR WALL TEMPLATE AND MARK
WALL
Overhead cabinet styles vary. Follow the instructions that apply to the cabinet style
in your home.
IMPORTANT: Disconnect power to electrical outlet.
STYLE 1 - FLAT-BOTTOM CABINET
IMPORTANT: The microwave must be level. Use a carpenter’s level to make
sure the cabinet bottom is level.
1. Draw a vertical line on the wall at the center of the 24" (61 cm) wide opening.
2. Place the Mounting Plate/Rear Wall Template onto the wall so that the
centerline of the template is aligned with the center line, and the top of the
template is touching the bottom of the cabinet. Tape the template in this
position.
7
ENGLISH
16½"
(41.9 cm)
a
A
Center
Line
STYLE 2 - FRAMED, RECESSED CABINET
IMPORTANT: The microwave must be level. Use a carpenter’s level to make
sure the cabinet bottom is level.
1. Draw a vertical line on the wall at the center of the 24" (61 cm) wide opening.
2. Place the Mounting Plate/Rear Wall Template onto the wall so that the
centerline of the template is aligned with the center line, and the top of the
template is touching the bottom of the cabinet. Tape the template in this
position.
a
3/
8
"
TO
E
D
GE
NO
T
E: IT IS VERY I
MP
O
RTANT
T
O
RE
AD AND
FO
LLOW
T
HE DI
RECTIONS
I
N
THE
INSTAL
LA
TION I
NSTRUCT
IONS
BE
F
ORE
PROCE
EDING
WIT
H THIS
REAR WAL
L TE
MPLATE.
This Rear Wa
l
l Temp
l
a
te serves to positio
n
the bot
tom
mountin
g plate and to locate t
h
e
ho
rizon
tal exh
aust
ou
tl
e
t
.
1. U
se a
level
to
che
ck t
hat th
e
templ
ate is positioned
a
cc
urately.
2. L
ocate a
nd ma
rk
a
t
least one stud on t
h
e l
eft
o
r
right s
ide
of t
h
e cen
te
rl
i
ne.
It
is
i
mportant
to use a
t least
o
ne w
o
od
scr
e
w
m
ounte
d
f
irmly i
n
a stud to sup
port the w
e
ight
of the mi
cr
ow
ave
. M
a
rk two additi
onal
, e
ve
nl
y sp
a
ced
l
o
ca
tio
ns for
th
e
suppli
e
d
t
oggle
b
ol
ts
.
3
.
D
rill
h
oles
in
th
e
mar
ked lo
cat
ions. Wh
e
r
e there is
a stud, d
ri
ll a 3/
1
6"
ho
le
for
w
oo
d scr
ews.
For
hole
s
t
hat d
o n
ot l
ine up with
a st
u
d, d
rill 5/8
" hol
es f
or
to
ggle
b
o
l
ts.
DO
N
OT I
N
STALL TH
E M
OUN
T
IN
G PLAT
E
AT TH
IS TIME
.
4
.
Remo
ve
the template
from the re
ar wal
l.
5. Re
view
the Installa
tion Instruction
book for your
installatio
n si
t
uati
on.
Loc
ate
and mark holes to al
i
gn wi
t
h h
ole
s i
n
the
mou
nt
i
ng plate.
I
MPORTANT:
LOCATE AT LEAST
ONE S
T
UD
ON EITHE
R
S
IDE
OF
T
HE CENTER
LINE.
MARK
T
HE LOC
A
T
ION FOR
2 A
D
DITIONAL,
E
VENLY
SPA
CE
D
TOGGLE
BOLTS
IN
TH
E MOU
NT
ING
PL
ATE
AREA.
Locate
and
ma
rk
holes to ali
gn with hole
s in
the
moun
t
ing pl
at
e.
IMP
O
RTA
NT:
LOCA
TE
A
T LE
AST
ONE
STUD ON EI
THER S
IDE OF
THE
CE
NTERLI
NE.
MA
RK
THE LOC
ATI
O
N
F
O
R 2
ADDIT
I
ONAL,
EV
ENL
Y
SPACE
D
TO
GG
LE
BOLT
S
I
N
THE MOUNT
ING PLATE
ARE
A.
Trim
the re
ar
w
a
ll temp
late al
ong the do
tted lin
e.
T
rim th
e
rea
r wall temp
l
ate al
on
g t
he
dotted
l
ine.
12"
4"
Da
rl
e
v
uelta a la hoja pa
r
a
co
nsulta
r
la
versión
en Es
pa
ñ
ol.
b
A
Center Line
B
30" (76.2 cm) to
cooktop
STYLE 3 - RECESSED CABINET WITH FRONT OVERHANG OR
DECORATIVE TRIM
IMPORTANT:
•
The microwave must be level. Use a carpenter’s level to make sure the
cabinet bottom is level.
•
If a decorative cabinet trim is interfering with the installation and leveling of
the microwave oven, remove the decorative trim.
•
If the cabinets have a front overhang, but no back or side overhang, to keep
the microwave level, place the mounting plate so that the distance from the
top of the mounting plate to the cabinet bottom is equal to the distance
from the bottom of the front overhang to the bottom of the cabinet.
8
ENGLISH
1. Measure the inside depth of the front overhang.
2. Draw a horizontal line on the back wall that is the same distance below the
cabinet bottom as the depth of the front overhang.
a
b
16½"
(41.9 cm)
A
Center
Line
B
Draw a
line on
the back
wall equal
to the
depth of
the front
overhang
3. Draw a vertical line on the wall at the center of the 24" (61 cm) wide opening.
4. Place the Mounting Plate/Rear Wall Template onto the wall so that the
centerline of the template is aligned with the center line, and the top of the
template is the same distance below the cabinet bottom as the depth of the
front overhang. Tape the template in this position.
STEP 4 - DRILL HOLES FOR MOUNTING MICROWAVE
OVEN
IMPORTANT: At LEAST one wood screw mounted
rmly in a stud must be
used to support the weight of the microwave.
1. Draw a horizontal line on the wall marking the bottom of the Rear Wall
Template.
2. Locate holes A and B inside the Mounting Plate Area indicated on the rear wall
template.
3. Place the mounting plate on top of the rear wall template centered in the
Mounting Plate Area so that the holes on the mounting plate align with the
holes on the template.
4. Mark the wall through holes A and B.
IMPORTANT: If neither Hole A nor Hole B aligns with a stud, locate a stud
within the mounting plate area and mark a third hole that aligns with the
stud.
5. Remove the mounting plate and set it aside. Drill holes in the marked locations.
NOTE: A wood screw must be used when installing into a wood stud.
•
Drill a ⁵⁄₈" hole to use a toggle bolt
•
Drill a ³⁄₁₆" hole to use a wood screw.
6. DO NOT INSTALL THE MOUNTING PLATE AT THIS TIME.
9
ENGLISH
3/8" TO EDGE
24” MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
Trim the rear wall template along the dotted line.
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
12"
4"
Darle vuelta a la hoja para consultar la
versión en Espa
ol.
e efa b
d
c
A
Hole A
B
Hole B
C
Draw a Vertical Line on Wall
marking Center of Top Cabinet
D
Centerline notches
E
Draw a horizontal line on wall marking
the bottom of Rear Wall Template.
F
Mounting Plate Area
STEP 5 - DETERMINE VENTILATION METHOD
IMPORTANT: This microwave oven is shipped assembled for a Recirculating
Ventilation Installation; however, it is designed to adapt to the following
methods of ventilation. Select the ventilation method required for your
installation and follow the instructions specic to your method:
Method A - Outside Top Exhaust (Vertical Duct)
10
ENGLISH
Method B - Outside Back Exhaust (Horizontal Duct)
Method C - Recirculating (Non-Vented, Ductless)
STEP 6 - INSTALL MICROWAVE OVEN
Install the microwave oven following the instructions specic to your method of
ventilation: Method A - Outside Top Exhaust, Method B - Outside Back Exhaust,
Method C - Non-Vented (Recirculating)
METHOD A - OUTSIDE TOP EXHAUST
IMPORTANT:
•
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help avoid excessive vibration.
•
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.
INSTALL MOUNTING PLATE
NOTE: At least one wood screw must be used to attach the plate to a wall stud.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the holes designated to go into
drywall and reattach the toggle wings onto each bolt.
11
ENGLISH
3. Place the mounting plate against the wall and insert the toggle wings into the
holes in the wall to mount the plate.
b
a
d
c
f
e
A
Mounting Plate
B
Wall
C
Bolt End
D
Spacing for Toggles
More Than Wall
Thickness
E
Toggle Wings
F
Toggle Bolt
4. Press the mounting plate ush against the wall. Make sure the mounting plate
touches the bottom of the horizontal line and that the plate is centered under
the cabinet.
NOTE: Avoid pinching
ngers between the back of the mounting plate
and the wall.
5. Tighten all bolts.
NOTE: Pull the plate away from the wall to help tighten the bolts.
PREPARE OVERHEAD CABINET
1. Read the instructions on the Top Cabinet template, and then tape the template
underneath the overhead cabinet.
2. Drill the holes following the instructions on the template.
•
Drill holes for the top support screws.
•
Drill a hole large enough for the power cord to
t through.
•
Drill a cutout large enough for the exhaust adapter.
10-23/64
12
ENGLISH
ADAPT BLOWER FOR OUTSIDE TOP EXHAUST
1. Place the microwave in an upright position.
2. Remove and save the three screws fastening the exhaust plate to the
microwave.
3. Remove and save the screw fastening the blower motor to the microwave.
b
d
c
a
A
Exhaust Plate Screw (3)
B
Exhaust Plate
C
Back of Microwave
D
Blower Motor Screw
4. Carefully pull out the blower unit. The wires will extend far enough to allow you
to adjust the blower unit.
b
a
c
A
End A
B
End B
C
Back of Microwave
5. Roll the blower unit 90° so that fan blade openings are facing out the top of the
microwave.
Before Rotation
After Rotation
a
a
b
A
Back of Microwave
B
Fan Blade Openings
6. Place the blower unit back into the microwave.
7. Using the blower motor screw removed earlier, secure blower unit to
microwave. Completely tighten the screw.
a
b
A
AFTER: Fan Blade Openings
Facing Top
B
Back of Microwave
8. Using the three blower plate screws removed earlier, reinstall the blower plate.
Completely tighten the screws.
13
ENGLISH
a
A
Back of Microwave
MOUNT THE MICROWAVE OVEN
WARNING
Excessive Weight Hazard
Use two or more people to move and install microwave oven.
Failure to do so can result in back or other injury.
NOTE: If the cabinet front hangs below the bottom cabinet shelf it is
recommended that you use ller blocks to avoid damaging the case by over
tightening the screws.
a
b
c
e
d
A
Cabinet Front
B
Cabinet Bottom
C
Filler Block
D
Equivalent to Depth of
Cabinet Recess
E
Microwave Oven Top
1. Thread the power cord through the hole in the bottom of the overhead cabinet.
Keep the power cord tight while mounting the oven.
NOTE: If the overhead cabinet is metal, use the nylon grommet around
the power cord hole to avoid cutting the power cord.
2. Using two or more people, lift the microwave, tilt it forward, and hook slots at
back bottom edge onto four lower tabs of mounting plate.
3. Rotate microwave so that the top is up against cabinet bottom.
NOTE: Keep the power cord tight, and do not pinch the cord, especially
when mounting
ush to bottom of cabinet.
14
ENGLISH
4. Insert the two mounting screws through the holes in the overhead cabinet and
into the holes in the top of the microwave oven. Turn each screw until it is
completely tightened.
a a
5. Holding the microwave oven ush against the back wall and the overhead
cabinet, tighten the two screws completely.
CONNECT DUCTWORK
1. Extend the house exhaust duct down, and then connect the exhaust duct to a
range hood boot adapter (not supplied).
2. Seal exhaust duct joints using furnace duct tape for high temperature
applications.
a
A
Adapter
15
ENGLISH
INSTALL GREASE FILTERS
Grease lters are located on the underside of microwave oven. For
installation instructions, see the User Manual packed with the microwave.
a b
c
d
A
Surface Lights
B
Door
C
Grease Filters
METHOD B - OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
IMPORTANT:
•
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help avoid excessive vibration.
•
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.
CREATE REAR WALL EXHAUST OPENING
3
/8" TO E
DGE
NO
TE: IT IS VE
RY IM
PORTAN
T TO
RE
AD
AND
FOLL
OW
TH
E
DIR
EC
TIONS
IN T
HE IN
STA
L
LATION INSTRU
CTIONS
BEFORE
PR
OCEED
ING
WITH
THIS
RE
AR
W
ALL
TEMPLA
TE.
This
Re
ar
Wall Tem
plate
serv
es
t
o posit
i
on th
e bot
tom
mounting plate and to loc
a
te the horizontal exhaust
ou
tlet.
1. Use
a level t
o
check that th
e templat
e
is
positioned
accurately.
2.
Locat
e
and
mark at
l
ea
st
one
stud on
t
he left
or
right
side o
f
t
he c
ent
erl
ine.
It is
important to
use at least
on
e
wood
scr
ew moun
te
d
f
irmly in a
st
ud
t
o sup
port
t
he
weight
of th
e
m
i
crowave.
Mark two
a
dditional, e
venly spaced
locat
ions f
or
the suppl
ied toggle bolts.
3. Dri
ll
holes in
th
e
m
arked locations.
Where t
here is
a st
ud, drill a
3/
1
6"
hole for wood screws.
F
or h
oles
that do n
ot
line up wit
h
a
stud,
d
rill
5
/
8
"
hole
s for
t
oggle
bolts.
DO
NOT
I
N
S
T
ALL
THE
MOUNTING
PLATE
AT T
HI
S
T
I
M
E.
4.
Rem
o
v
e
the template from the rear wall.
5. Review the Installa
t
ion Instruction boo
k for y
our
installation sit
u
a
t
io
n.
Lo
cate and mar
k hol
es to
a
lig
n with holes
in the
mo
unti
ng plate
.
IMP
ORTANT:
LOCATE
AT LEAST ON
E STUD
ON
EITHER
S
ID
E
OF
TH
E
C
ENTER
LIN
E.
MARK THE L
OCATION FOR
2 ADD
ITIO
NAL, EVEN
LY
SP
ACED TOGGLE BO
LTS IN
THE
MOU
NTING PLATE
AREA.
Locate and mar
k hol
es to
a
lig
n with holes in the
mo
unting
plate.
IMPORTA
NT:
LO
CATE
AT LE
AST ON
E STU
D O
N EITH
ER
SIDE OF
THE CE
NTERLINE.
MA
RK TH
E LOCATION FOR
2 AD
DIT
IO
NAL, EVEN
LY
SP
ACE
D
TOGG
LE
BOLTS
IN THE
M
OU
NTI
N
G PLA
TE
AR
EA.
Trim the r
ea
r wall templa
te a
l
ong the dotted
line.
Trim the
r
ea
r
wall te
mpla
te
alo
ng
the
d
otted
lin
e.
12"
4"
Darle vuelta a la hoja
par
a co
nsultar
la
versión en E
spañol.
1. Read the instructions on the Mounting Plate/Rear Wall template.
2. Tape the Mounting Plate/Template to the rear wall, aligning it with the holes
previously drilled for holes A and B in the mounting plate.
3. Cut the opening, following the instructions on the Rear Wall template.
REMOVE THE BLOWER PLATE
1. Remove and save the screw(s) fastening the blower plate to the microwave.
2. Lift o the blower plate.
16
ENGLISH
b
a
A
Exhaust Plate
B
Back of Microwave
INSTALL MOUNTING PLATE
NOTE: At least one wood screw must be used to attach the plate to a wall stud.
1. Remove the toggle wings from the bolts.
2. Insert the bolts into the mounting plate through the holes designated to go into
drywall and reattach the toggle wings onto each bolt.
3. Place the mounting plate against the wall and insert the toggle wings into the
holes in the wall to mount the plate.
b
a
d
c
f
e
A
Mounting Plate
B
Wall
C
Bolt End
D
Spacing for Toggles
More Than Wall
Thickness
E
Toggle Wings
F
Toggle Bolt
4. Press the mounting plate ush against the wall. Make sure the mounting plate
touches the bottom of the horizontal line and that the plate is centered under
the cabinet.
NOTE: Avoid pinching ngers between the back of the mounting plate
and the wall.
5. Tighten all bolts.
NOTE: Pull the plate away from the wall to help tighten the bolts.
PREPARE OVERHEAD CABINET
1. Read the instructions on the Top Cabinet template, and then tape the template
underneath the overhead cabinet.
2. Drill the holes following the instructions on the template.
17
ENGLISH
•
Drill holes for the top support screws.
•
Drill a hole large enough for the power cord to t through.
•
Drill a cutout large enough for the exhaust adapter.
10-23/64
ADAPT BLOWER FOR OUTSIDE REAR EXHAUST
1. Remove and save the screw fastening the blower motor to the microwave.
b
d
c
a
A
Exhaust Plate Screw (3)
B
Exhaust Plate
C
Back of Microwave
D
Blower Motor Screw
2. Carefully pull out the blower unit. The wires will extend far enough to allow you
to adjust the blower unit.
b
a
c
A
End A
B
End B
C
Before: Fan Blade Openings
Facing Forward
3. Roll the blower unit 90°.
Before Rotation
After Rotation
a
a
b
A
Back of Microwave
B
Fan Blade Openings
4. Rotate blower unit counterclockwise 180°.
18
ENGLISH
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
dans d''autres langues
- English: Avanti 851070 Installation guide
- español: Avanti 851070 Guía de instalación
Autres documents
-
Haier HMV1472BHS Installation Instructions Manual
-
-
Frigidaire EI30SM35QS Guide d'installation
-
Whirlpool WMC10007AB Guide d'installation
-
-
-
-
Insignia NS-OTR16WH8 Template