Develco Products H6500130 Guide d'installation
- Taper
- Guide d'installation
eng
Resetting
Resetting is needed if you want to connect your
humidity sensor to another gateway or if you
need to perform a factory reset to eliminate ab-
normal behaviour.
STEPS FOR RESETTING
1. Open the casing of the Smart Humidity
Sensor.
2. Press and hold the round menu button
inside the device.
Mounting
1. Open the casing of the Smart Humidity
Sensor and remove the batteries.
Placement
• Place the sensor indoors at a temperature
between 0-50°C.
• Inside the room, in which you want to
monitor humidity levels.
• The Smart Humidity Sensor should be
placed on a wall, reachable for battery
testing and maintenance.
Product description
The Smart Humidity Sensor allows you to protect
your building and belongings by monitoring the
temperature and humidity levels, and receive
immediate alerts if the climate uctuates to
unsafe levels.
By supervising the indoor climate, the wireless
Smart Humidity Sensor helps maintain the ideal
comfort level and protect interior, electronics,
musical instruments, furniture, artwork, and
other humidity-sensitive household items.
Smart Humidity Sensor
2. Use double-sided tape or screws to attach
the sensor on the wall.
4. Make sure that the Smart Humidity Sensor has
joined a network before closing the casing.
3. Insert batteries respecting the polarities.
50 cm
150 cm
WALL
Version 2.0
INSTALLATION MANUAL
Precautions
• Do not remove the product label as it
contains important information.
• Be aware that electronics are sensitive
to static electricity, so aim to discharge
before touching, and avoid touching any
components inside the device.
• Do not place the Smart Humidity Sensor
on the ceiling, or behind obstacles, such as
curtains.
• Do not place the Smart Humidity Sensor
under direct sunlight or bright light.
• Avoid placing the Smart Humidity Sensor
close to radiators or electromagnetic elds.
• Do not paint the sensor.
1. Open the casing of the Smart Humidity
Sensor to replace the batteries.
Fault nding
• If the search for a gateway has timed out, a
short press on the button will restart it.
• In case of a bad or wireless weak signal,
change the location of the Smart Humidity
Sensor. Otherwise, you can relocate your
gateway or strengthen the signal with a
range extender.
2. Replace the batteries respecting the
polarities.
Battery replacement
The device will blink twice every minute when
the battery is low.
CAUTION:
• Do not attempt to recharge or open the
batteries.
• Risk of explosion if batteries are replaced by
an incorrect type.
• Dispose of a battery into re or a hot oven, or
mechanically crushing or cutting of a battery
can result in an explosion
• Leaving a battery in an extremely high
temperature surrounding environment can
result in an explosion or the leakage of
ammable liquid or gas.
• A battery subjected to extremely low air
pressure may result in an explosion or the
leakage of ammable liquid or gas
• Maximum operation temperature is 50°C /
122°F
• If you experience leakage from the batteries,
immediately wash your hands and/or any
aected area of your body thoroughly!
CAUTION: When removing cover for battery
change - Electrostatic Discharge (ESD) can
harm electronic components inside.
a.
b.
c.
d.
e.
f.
g.
h.
i.
Disclaimers
CAUTION:
• Choking hazard! Keep away from children.
Contains small parts.
• Please follow the guidelines thoroughly.
The Smart Humidity Sensor is a preventive,
informing device, not a guarantee or
insurance that sucient warning or
protection will be provided, or that no
property damage, theft, injury, or any similar
situation will take place. Develco Products
cannot be held responsible in case any of
the above-mentioned situations occur.
6. When the LED stops ashing, the Smart
Humidity Sensor has successfully joined the
Zigbee network.
5. While the Smart Humidity Sensor is search-
ing for a Zigbee network to join, the LED
ashes red.
2. Insert two AA batteries respecting the
polarities.
3. The Smart Humidity Sensor will now start
searching (up to 15 minutes) for a Zigbee
network to join.
4. Make sure that the Zigbee network is open
for joining devices and will accept the Smart
Humidity Sensor.
Getting started
1. Open the sensor by pushing the switch and
pulling the top of the casing.
3. While you are holding the button down, the
LED rst ashes once, then two times in a
row, and nally numerous times in a row.
4. Release the button while the LED is ashing
numerous times in a row.
5. After you release the button, the LED shows
one long ash, and the reset is completed.
Other certications
• Zigbee Home Automation 1.2 compliant
Other certications
IC statement
Develco Products assumes no responsibility for
any errors, which may appear in this manual.
Furthermore, Develco Products reserves the
right to alter the hardware, software, and/
or specications detailed herein at any time
without notice, and Develco Products does
not make any commitment to update the
information contained herein. All the trademarks
listed herein are owned by their respective
owners.
All rights reserved.
Distributed by Develco Products A/S
Tangen 6
8200 Aarhus N
Denmark
www.develcoproducts.com
Copyright © Develco Products A/S
FCC statement
Changes or modications to the equipment not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful
interference to radio or television reception,
which can be determined by turning the
equipment o and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/
TV technician for help.
This device complies with FCC RF radiation
exposure limits set forth for an uncontrolled
FCC statement
ISED statement
Innovation, Science and Economic Develop-
ment Canada ICES-003 Compliance Label:
CAN ICES-3 (B)/NMB-3(B).
ISED statement
IN ACCORDANCE WITH THE DIRECTIVES
• Radio Equipment Directive (RED)
2014/53/EU
• RoHS Directive 2015/863/EU amending
2011/65/EU
CE certication
The CE mark axed to this product conrms
its compliance with the European Directives
which apply to the product and, in particular, its
compliance with the harmonized standards and
specications.
CE certication
Français
L’émetteur/récepteur exempt de licence
contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences
et Développement économique Canada
applicables aux appareils radio exempts de
licence. L’exploitation est autorisée aux deux
conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.
Cet équipement est conforme aux limites
d’exposition aux radiations IC CNR-102 établies
pour un environnement non contrôlé. Cet
équipement doit être installé et utilisé avec une
English
This device contains licence-exempt
transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference,
including interference that may cause
undesired operation of the device.
This equipment complies with IC RSS-102
radiation exposure limits set forth for an
uncontrolled environment. This equipment
should be installed and operated with minimum
distance 20 cm between the radiator and your
body.
Disposal
Dispose the product and batteries properly at
the end of life. This is electronic waste which
should be recycled.
3. Close the casing of the sensor.
j. environment. The antenna used for this
transmitter must be installed to provide a
separation distance of at least 20 cm from
all persons and must not be co-located or
operating in conjunction with any other antenna
or transmitter.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interfer-
ence, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
distance minimale de 20 cm entre le radiateur
et votre corps.
-
1
-
2
