Fisher & Paykel WL26CW1 Installation Instructions And User Manual

AquaSmart™ clothes washer

Installation instructions

and user guide US CA (EN)

WL26CW1

Laveuse AquaSmart™

Instructions d’installation

et guide de l’utilisateur US CA (FR)

Lavadora AquaSmart™

Instructivo de instalación

y guía de usuario US CA (ES)

Please Note: To obtain maximum efficiency, your AquaSmart™ washer has the ability to learn

and adapt to the local environment. This may take several wash cycles, therefore maximum

energy efficiency may not be achieved until a number of wash cycles have been completed. This

usually takes about 5 cycles.

As an ENERGY STAR® Partner Fisher & Paykel Limited has determined

that this product meets ENERGY STAR® guidelines for energy efficiency.

WARNING!

Electric Shock Hazard

Read and follow the SAFETY AND WARNINGS outlined in this User Guide

before operating this appliance, pages 3 – 5.

Failure to do so can result in death, electric shock, fire or injury to persons.

English Page 1 – 45

Español Pág 46 – 83

Français Page 84 – 121

1

Safety and warnings 3

Installation instructions 6

Before you do your first wash 12

Checklist, Water consumption, Capacity 12

Getting started quickly 14

AquaSmart™ controls 16

Easy touch controls, The display screen, Time to go 16

The unique AquaSmart™ wash 17

Fully automatic water level 18

Sorting and loading 18

Detergent/Bleach 19

Fabric Softener 20

Choosing your wash cycle 21

Changing the wash cycle options 22

Wash cycle options 23

Wash cycles explained 24

Bulky wash options 27

Lifestyle cycles 28

Special Care Handwash / Wool / Jeans 29

Stains Chocolate / Tomato / Blood / Grass / Fruit / Wine 30

Family Comforter / Allergy / Hygiene / Diaper Rinse / Soft Toys 31

Sports Sweaty / Muddy / Sports Shoes / Beach Gear 32

Clean Up Clean Me 32

Settings Menu 33

Balance Recovery / Alarm Level 33

Screen Brightness / Key Lock Mode / Hints 34

Language / Service Contacts / Trouble Shooting / Reset Defaults / Replay Intro 35

Lid Lock 35

Caring for your AquaSmart™ washer 36

Before you call for service 38

If your AquaSmart™ beeps for help 38

Solving operating problems 40

Solving wash problems 42

Limited warranty 43

Important!

SAVE THESE INSTRUCTIONS

Contents

The models shown in this user guide may not be available in all markets and are subject to change

at any time. For current details about model and specification availability in your country, please go

to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

EN

2

Welcome to AquaSmart™

Thank you for buying a Fisher & Paykel AquaSmart™ clothes washer. We are very proud of this

washer and trust it will serve you well for many years.

At Fisher & Paykel we aim to provide innovative products that are simple to use, ergonomic and

kind to the environment. Thousands of tonnes of washing and 70 years of laundry experience

have been programmed into your clothes washer to help give you the best possible performance.

Your AquaSmart™ clothes washer works differently from a conventional washer. It is a “High

Efficiency” washer utilizing innovative technology to wash in less water and take great care of

your clothes.

It is important that you take the time to read these instructions carefully before you begin using

your washer. Like all High Efficiency washers, a little extra care in how you sort your clothes and

choose your cycle and detergent will ensure that you get the best possible wash result.

We hope you enjoy your new washer, we have certainly enjoyed designing it for you.

Introduction

Important!

It is important that this User Guide should be retained with your AquaSmart™ clothes washer

for future reference. Should the appliance be sold or transferred to another owner, please ensure

that the User Guide is left with the appliance. This will ensure that the new owner can familiarise

themselves with the information and warnings contained within the Guide.

3

Safety and warnings

Read all safety information before using

Many washers are located near a gas dryer or a water heater in the home.

WARNING!

Fire Hazard

For your safety the information in this manual must be followed to

minimize the risk of fire or explosion or to prevent property damage,

personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

Installation and service must be performed by a qualified installer, service

agency or the gas supplier.

What to do if you smell gas

DO NOT try to light any appliance.

DO NOT touch an electrical switch; do not use any phone in your building.

Clear the room, building or area of all occupants.

Immediately call your gas supplier from your neighbor’s phone.

Follow the gas supplier’s instructions.

If you cannot reach your gas supplier, call the fire department.

Water heater safety

Under certain conditions Hydrogen gas may be produced in a water heater that has not been

used for two weeks or more.

HYDROGEN GAS CAN BE EXPLOSIVE UNDER THESE CIRCUMSTANCES.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or

injury by turning on all hot water faucets and allowing them to run for several minutes before

using any electrical appliance which is connected to the hot water system. This will allow any

hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or

appliance during this process.

EN

4

WARNING!

Electric Shock Hazard

Follow the safety precautions outlined in this User Guide.

Failure to do so can result in death, electric shock, fire or injury to persons.

Important safety precautions

Read all instructions before using the appliance.

Use this appliance only for its intended purpose as described in this User Guide.

This washer must be properly installed and located in accordance with the Installation Instructions

before it is used.

This washer must be properly grounded to conform with all governing codes and ordinances. Follow

details in the Installation Instructions.

Do not install or store washer where it will be exposed to temperatures below freezing or exposed to

the weather.

Connect to a properly rated, protected and sized power supply circuit to avoid electrical overload.

Connect to adequate plumbing and drain facilities as described in the Installation Instructions.

Turn off water faucets when the washer is not in use to relieve pressure on hoses and valves and to

minimize leakages if a hose or valve should break or rupture.

Do not repair or replace any part of the appliance or attempt any servicing unless specifically

recommended in this User Guide or in published user repair instructions that you understand, and

have skills to carry out.

When disconnecting the appliance pull by the plug rather than the cord or junction of cord to avoid

damage to the cord or junction of the cord and plug.

Make sure that the cord is located so that it will not be stepped on, tripped over or otherwise subject

to damage or stress.

Keep all laundry aids (such as detergents, bleach, fabric softener, etc.) out of the reach of children,

preferably in a locked cabinet. Observe all warnings on container labels to avoid personal injury.

Do not tamper with the controls.

Keep the area around/underneath your appliance free from the accumulation of combustible

materials, such as lint, paper, rags, chemicals, etc.

Keep the floor around your appliance clean and dry to reduce the possibility of slipping.

Never reach into the washer if the tub or agitator is moving.

Before loading, unloading or adding clothes, press START/PAUSE and wait until the washer has

completely stopped before opening the lid.

Close supervision is necessary if this appliance is used by or near children. Do not allow children to

play inside, or on, or with this appliance or any discarded appliance.

Safety and warnings

5

Safety and warnings

Dispose of discarded appliances and shipping/packing materials properly. Before discarding a

washer, or removing from service, remove the washer lid.

Do not leave the washer lid up during the cycle. The washer will not function. To start, close lid and

press START/PAUSE.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with

combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.) which may ignite or explode. Do not add these substances to the wash

water. Do not use these substances around your washer and/or dryer during operation, as they give

off vapors that could ignite or explode.

The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, the garment

manufacturer’s care instructions should be followed very carefully.

Do not mix chlorine bleach with ammonia or acid such as vinegar and/or rust remover. Mixing can

produce a toxic gas which may cause death.

Never climb on or stand on the washer top or lid.

Do not wash fibreglass articles in your washer. Skin irritation could result from the remaining

particles that may be picked up by clothing during subsequent washer use.

To minimize the possibility of electric shock, unplug this appliance from the power supply or

disconnect the washer at the household distribution panel by removing the fuse or switching off the

circuit breaker before attempting any maintenance or cleaning.

Note: Pressing the POWER button does NOT disconnect the appliance from the power supply, even

though the lights are out.

Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or has

missing or broken parts, including a damaged cord or plug.

Do not operate this appliance if the lid has been incorrectly fitted.

If you are using an extension cord or a portable electrical outlet device (eg mulit-socket outlet box),

ensure that it is positioned so that it does not come into contact with water or moisture.

SAVE THESE INSTRUCTIONS

EN

Before you begin – read these instructions completely and carefully.

WARNING!

Electric Shock Hazard

Read and follow the SAFETY AND WARNINGS outlined in this User Guide

before operating this appliance, pages 3 – 5.

Improper connection of an equipment-grounding conductor can result in a

risk of electric shock. Check with a qualified electrician or serviceman if you

are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance – if it will not fit the

outlet, have a proper outlet installed by a qualified electrician.

Failure to do so can result in death, electric shock, fire or injury to persons.

Important!

Observe all governing codes and ordinances.

Installation Requirements

Location

Your washer must be installed on firm flooring to minimize vibration during spin cycles. Concrete

flooring is best, but wood base is sufficient providing the floor support meets FHA standards.

Your washer should not be installed on rugs or exposed to the weather.

Plumbing

Water Temperature

Your cold water should not exceed 95˚F (35˚C) or your hot water exceed 149˚F (65˚C).

Temperatures above this may damage your washer.

Shut Off Valves

Both hot and cold shut-off valves (faucets) should be available in the laundry area.

Drain

Water may be drained into a standpipe or set tub/sink. The standpipe must be 1 ½” (38 mm)

minimum interior diameter and must be open to the atmosphere.

Electrical

This appliance must be supplied with 110V – 120V, 60Hz electrical supply and connected to an

individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time

delay fuse.

Installation instructions

6

7

Water supply

This washer must be plumbed into both a hot and cold water supply or it will not work

correctly. Please ensure that both hot and cold water are connected to the washer.

If you have an uncontrolled water-heating source (eg a wet back or solar heating) you should

have a tempering device fitted. This will ensure the hot water temperature remains within

safe limits. For the most suitable type of tempering device we recommend you contact a local

plumber or plumbing supply merchant.

Inlet Water Static Pressure 3psi (20kPa) to 150psi (1MPa).

(If using a header tank then the top of the header tank must be at least 39” (2 m) above the top

of your clothes washer).

Minimum flow rate from the faucet supplying the clothes washer should be greater than

1 ½ gallons/min (6 liters/min) (assumes ½” (12.7 mm) diameter pipes).

Minimum height of faucets to clear the top of the washer is 45” (1150 mm).

Draining

Regularly check that your standpipe or set tub/sink is free from lint or other obstructions, which

may affect how your washer works or may cause flooding.

In multi-storey apartments or any upper floor, the washer should be installed on a drained floor.

Draining must comply with local by-laws.

Clothes washer safety

This clothes washer is not intended for use by young children or infirm persons without

supervision.

Please supervise young children to ensure they do not play with this clothes washer.

Important!

If you are using an extension cord or a portable electrical outlet device (eg multi-socket outlet

box), ensure that it is positioned so that it does not come into contact with water or moisture.

Accessories and spare parts

Available from your Fisher & Paykel Dealer or Authorised Service Center.

Drain Hose Extension Part No. 425627p

Power Cord If the Power Cord of your clothes washer is damaged it must be

replaced by a Fisher & Paykel Authorised Service Center, as it

is not a standard power cord.

Installation instructions

EN

8

Fig.1 Tilt washer backwards

to remove packer

Unpacking

To ensure the best performance from your new AquaSmart™

clothes washer please follow the instructions below.

Removing the packaging

1

Remove the outer packaging.

2

Tilt the washer backwards and walk it off the bottom

packer one foot at a time.

3

Remove the bottom packer from under the washer by

pulling it out the front.

Caution!

Operating the washer when the bottom packer is in

place can result in damage to the washer.

4

Lift the lid and remove the basket packer from the basket.

5

Remove the hoses and accessories.

6

Keep the bottom packer and basket packer in case they are required for future transit.

Please ensure that the bottom packer has been removed before operating your washer.

Installation

In your clothes washer you will find:

4 rubber inserts for the levelling feet (joined together).

1 hose guide.

2 inlet hoses.

Installation instructions

9

Drain hose

1

Carefully pull the drain hose out from the

back of the washer by pulling the exposed

part of the hose downwards and outwards.

2

To guide the drain hose over the set tub/sink

or standpipe the hose guide MUST be fitted

to the drain hose.

To prevent siphoning:

The drain hose should not extend more than

¾” (20 mm) from the end of the guide.

The height of the standpipe or set tub/sink

should be between 33 ½” to 78” (850 – 1200 mm).

The drain hose can be trimmed to length.

3

Place the drain hose in the set tub/sink or

standpipe.

Important!

In multi-storey apartments or any upper floor installation, the washer should be installed on a

drained floor.

Check that the tub or standpipe is free from lint or other obstructions before operating the washer.

In a basement installation do not exceed a standpipe height of 96” (2438 mm).

Inlet hoses

1

Install hoses with the straight end (with filters) fitted to the faucets (refer to Fig.3).

2

Install elbow ends onto clothes washer (inlet valves are marked on the back of the washer

H=hot, C=cold) (refer to Fig.4).

Fig.3 Faucet end of hose Fig.4 Washer end of hose

Installation instructions

Fig.2 Fitting the drain hose guide

Flex hose

guide apart

Standpipe 33 ½” to 78” (850 – 1200 mm)

¾” (20 mm)

maximum

Pull hose

through guide

EN

10

Levelling your washer

It is IMPORTANT to level the washer to ensure good spin performance and effective detergent and

fabric softener dispensing.

1

Separate the 4 rubber foot inserts from the moulding and fit into the feet on the base of the

washer.

2

Move the washer to its final position. (We suggest a minimum clearance of 1” (25 mm) each side).

3

Adjust the feet so the washer is level and cannot rock.

4

Use the walls and adjacent counter tops as a sight guide to check to see if washer appears level.

Readjust the feet if necessary.

5

Open the lid and check the washer tub to see that it sits slightly forward of centre. (See diagram 3).

Correct

adjustment

Incorrect

adjustment

Diagram 3

6

Turn on the water and check all hose connections for leaks. Make sure there are no kinks in the hoses.

7

Uncoil power cord and plug into wall socket.

8

Check for leaks, noise, vibration, correct water temperatures and proper operation in spin. Check

that the lid locks during spin.

Adjustable feet

Rubber insert

Fig.5 Levelling your washer

1” (25 mm) 1” (25 mm)

Fig.6 Minimum clearances

Installation instructions

11

Special requirements for alcove or closet installation

The minimum ventilation clearance between the washer and adjacent walls or other surfaces is:

1” (25mm) minimum either side and front

3” (75mm) minimum rear

Consideration must be given to providing adequate

clearance for installation and servicing.

The minimum vertical space required from floor

to overhead shelves, cabinets, ceilings etc is 59”

(1500 mm).

Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches open

area for a washer only, or if the closet contains both

a washer and dryer, doors must contain at least 120

square inches of open area equally distributed.

Caution!

Do not install this appliance in a closet with a solid door.

Mobile home installation

Installation must conform to the STANDARD FOR MOBILE HOMES, ANSI A119.1 and NATIONAL

MOBILE HOME CONSTRUCTION & SAFETY STANDARDS ACT OF 1974 (PL93-383).

Grounding instructions

This appliance must be grounded. In the event of malfunction or break down, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a cord that has an equipment-grounding conductor and a

grounding plug. The plug must be plugged into an appropriate outlet that is properly installed

and grounded in accordance with all local codes and ordinances.

Specification subject to change without notice.

Installation instructions

60 Sq. In

(388 Sq. cm)

60 Sq. In

(388 Sq. cm)

Fig. 8 Louvered door Washer & Dryer

EN

12

You owe it to yourself and your AquaSmart™ to have it installed correctly by an authorised

service agent.

Before you start, it is a good idea to go through the following checklist:

1

Has the basepacker been removed?

2

Is the hot hose connected to the hot valve marked ‘H’?

Is the cold hose connected to the cold valve marked ‘C’?

3

Is the drain hose threaded through the ‘U bend’ (with no

more than ¾” 20 mm extended) and on to your standpipe?

4

Are the rubber inserts secured into the feet on the base of

your washer and is the washer levelled? Use the levelling

indicator bubble to check if washer is level (refer to page 10).

Refer to Installation instructions, pages 6 – 11.

AquaSmart™ water consumption

Load Size Regular High Efficiency*

15.5 lb (7 kg) 22 G (82 L)

11 lb (5 kg) 18 G (69 L)

7 lb (3 kg) 16 G (60 L)

2 lb (1 kg) 14 G (54 L)

*Regular High Efficiency is the default wash cycle for AquaSmart™.

AquaSmart™ capacity

AquaSmart™ offers a generous 15.5 lb (7 kg) capacity. The list below outlines what is included in

a 15.5 lb (7 kg) wash load (in accordance with ANSI/AHAM HLW-1-2002).

3 Bed sheets (double)

2 Tablecloths

4 Shirts

6 Bath towels

4 T-shirts

4 Pillow cases

6 Shorts

6 Washcloths

5 Handkerchiefs

We recommend for everyday use that you separate out your bed sheets and wash them on the

specially designed BED SHEETS cycle.

Before you do your  rst wash

13

The  rst time you turn your washer on

Customizing your AquaSmart™ washer

The first time that you turn your washer on an intial set-up mode will be initiated. This is to

ensure that your AquaSmart™ is customized for your individual needs. The set-up mode will

prompt you to select the language that you would prefer your AquaSmart™ washer to use.

Australia US Español Canada

English

Canada

Français

New Zealand

US ENGLISH

Using the SCROLL buttons, scroll to the language that you would like your washer to use. Once

the language icon has been highlighted, press SELECT to confirm your choice. Your washer will

now use this language, and the initial set-up prompt will not appear again.

If you wish to change your language choice at any time, you can do this by simply selecting the

LANGUAGE option in the SETTINGS MENU (please refer to page 35).

EN

14 Getting started quickly

It is important to sort your clothes, particularly by color, as well as separating out bed sheets and

washing them on the BED SHEETS cycle. Jeans also need to be washed separately on the JEANS

cycle (refer to page 18 for more details on sorting and loading).

Close bra clasps, do up zippers and check pockets.

Place your clothes evenly around the wash tub.

Detergent

Your AquaSmart™ has been designed for use with High Efficiency (HE) detergent. For example

Tide® HE liquid or powder, Wisk® HE liquid or powder.

AquaSmart™ offers a Detergent dispenser for your convenience, located on the front, left hand

side of the top deck.

For detergent dose, please follow the manufacturers directions, outlined on the detergent

package.

Pour the detergent down the Detergent dispenser.

For more information on detergent, fabric softener please refer to pages 19 – 20.

Fig.9 AquaSmart™ control panel

1 2 6

15

Getting started quickly

Easy touch buttons and LCD screen

These buttons require only a gentle touch to activate.

1

Touch POWER to activate your AquaSmart™ washer.

2

HIGH EFFICIENCY – this light tells you when ‘High Efficiency’ mode is recommended, and the

button allows you to switch between High Efficiency and Conventional modes (refer to page

17).

3

The screen in the middle of the panel, will display the wash cycle options available (refer to

pages 21 – 27).

4

Use the SCROLL buttons to select the wash cycle that best suits your load (refer to page 21).

5

Use the SELECT/TICK button to confirm your selection. (For more information on how to alter

wash options refer to page 22).

6

Touch START – your AquaSmart™ will start to fill with water, and will automatically select the

correct water level and wash action for your load. To pause your AquaSmart™ at any time, simply

touch START/PAUSE.

3 4 5

EN

16 AquaSmart™ controls

Easy touch controls

These smooth, easy clean buttons require only a gentle touch to activate. To scroll you need to

remove your finger to break contact and touch it again. Once you become accustomed to the

soft touch technology you will find it effortless to operate.

High Efficiency mode

This button activates or deactivates the HIGH EFFICIENCY mode. The light

will be on when High Efficiency is selected, (please refer to High Efficiency

mode page 17). To select CONVENTIONAL mode simply press the High

Efficiency mode button and the light will turn off.

The High Efficiency symbol will appear on the screen when the mode

is active.

Scroll

The SCROLL buttons allow you to scroll between the wash options.

Select

Use the SELECT key to confirm your selected option and the BACK key to

cancel.

The display screen

The display screen allows you to view the available wash cycles and modify options. It provides

feedback on what your AquaSmart™ washer is doing and how long the wash has to go, to keep

you informed throughout the cycle. The screen will also display messages to help you with the

overall running of your washer.

Regular

CHOOSE

WASH

Time to go

Your AquaSmart™ washer will display how many minutes the wash cycle has to go, so that you

can tell at a glance when your washing will be finished. Once AquaSmart™ has finished the filling

and sensing process, the time to go will be displayed. A progress bar is also displayed and will

move along as the cycle progresses. Please be aware that the flow rate of the water supply may

influence your cycle time.

17

The unique AquaSmart™ wash

The AquaSmart™ washer has two modes of washing, High Efficiency and Conventional. Both

modes start the same way, with a Detergent Activating wash.

Detergent Activating wash

AquaSmart™ fills the tub at the selected water temperature, with

just enough water so the clothes are saturated. This small amount

of sudsy water flows through the clothes, up a specially designed

portal and back onto the clothes in a waterfall effect. This

thoroughly dissolves and activates the detergent.

High Efficiency mode

In the High Efficiency mode the AquaSmart™ then fills with just

enough water to lift the clothes off the low profile agitator so when

it rotates, the clothes gently roll over each other. This wash uses

similar quantities of water to most Front Loaders and so, not only

do you get the benefits of water savings but the higher detergent

concentrations give you optimum soil removal.

Conventional mode

The Conventional mode is the immersion wash all Top Loader users

are familiar with. After the Detergent Activating wash the AquaSmart™

fills with cooler water until the clothes are submerged, and gently

turns the clothes over. We recommend this mode when the dilution

effect of water can solve or prevent common wash problems. For

example, when dye or color run can be a problem, or when washing

sandy towels. The BED SHEETS cycle uses the Conventional mode.

Some cycles can be used in both modes, whilst others work in only one.

High Efficiency Conventional

Regular –

Bed Sheets –

Whites –

Colors –

Heavy Duty

Delicate

Easy Iron –

Bulky –

These two wash modes mean that your AquaSmart™ washer gives you the best of both worlds,

to suit any laundry situation.

Fig.11 High Efficiency wash

Fig.12 Conventional wash

Fig.10 Detergent Activating wash

EN

18 Fully automatic water level

You may notice that your AquaSmart™ clothes washer behaves differently from your previous washer.

Your AquaSmart™, like all High Efficiency washers, has a fully automatic water level. This means

that, like Front Loaders, the selection of the water level is left entirely up to the washer. This

ensures optimum wash performance and water savings.

Should you wish to use more water, simply select a Conventional cycle (refer to Conventional

mode page 17).

Sorting and loading

You have bought a High Efficiency washer, like Front Loaders your AquaSmart™ uses much less

water and energy than Traditional Top Loading clothes washers. It is important to sort your wash

load to ensure optimum wash performance.

BED SHEETS – Separate out bed sheets and comforter covers and use the BED SHEETS

cycle which has been especially designed for these items. Ensure that comforter covers

are buttoned or zipped up. To get the best possible wash for bed sheets, load these items

around the edge of the tub rather than directly across the low profile agitator.

COLORED ITEMS – Dye or color run can be a problem with High Efficiency washers, so

separate highly colored garments especially when they are new and choose the COLORS

cycle. Most dye transfer occurs when clothes are left too long in the washer at the

completion of the cycle so try not to leave your colored clothes lingering in the washer.

BULKY ITEMS – Comforters, sleeping bags, ski jackets , blankets and throws are all items

which tend to behave unusually in a clothes washer. The lighter ones tend to float, while

a large blanket can get very heavy and make spinning difficult. Your AquaSmart™ has

specific BULKY cycles designed to take care of these washing challenges.

ITEMS THAT WRINKLE – When you are concerned about creasing or wrinkling we

recommend you use the EASY IRON cycle. Alternatively select one of the Conventional

cycles. The extra water used by these cycles will help to reduce wrinkling. Reducing the

spin speed of the wash may also help (refer to page 23).

JEANS – These heavy items are responsible for damaging other items in the wash and

require their own specific wash action to get clean. We feel so strongly that they should

be washed separately we created a special JEANS cycle in the Lifestyle menu. Select

LIFESTYLE, SPECIAL CARE, JEANS.

SOIL – Very dirty, sandy, or linty loads are best washed separately to prevent transfer

onto other garments. It may be that you have new towels that create lots of lint or very

sandy beach gear. We suggest using a Conventional cycle in this circumstance.

DELICATES – To take extra care of delicate items, we suggest using the DELICATE , or

HANDWASH cycles. For HANDWASH select LIFESTYLE, SPECIAL CARE, HANDWASH.

La page est en cours de chargement...

Fisher & Paykel WL26CW1 Installation Instructions And User Manual

Fisher & Paykel WL26CW1 Installation Instructions And User Manual

dans d''autres langues

Documents connexes